s390/qeth: use dev->groups for common sysfs attributes

All qeth devices have a minimum set of sysfs attributes, and non-OSN
devices share a group of additional attributes. Depending on whether
the device is forced to use a specific discipline, the device_type then
specifies further attributes.

Shift the common attributes into dev->groups, so that the device_type
only contains the discipline-specific attributes. This avoids exposing
the common attributes to the disciplines, and nicely cleans up our
sysfs code.

While replacing the qeth_l*_*_device_attributes() helpers, switch from
sysfs_*_groups() to the more generic device_*_groups().

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: replace deprecated simple_stroul()

Convert the remaining occurences in sysfs code to kstrtouint().

While at it move some input parsing out of locked sections, replace an
open-coded clamp() and remove some unnecessary run-time checks for
ipatoe->mask_bits that are already enforced when creating the object.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: stop yielding the ip_lock during IPv4 registration

As commit df2a2a5225cc ("s390/qeth: convert IP table spinlock to mutex")
converted the ip_lock to a mutex, we no longer have to yield it while
the subsequent IO sleep-waits for completion.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: remove open-coded inet_make_mask()

Use inet_make_mask() to replace some complicated bit-fiddling.

Also use the right data types to replace some raw memcpy calls with
proper assignments.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: overhaul L3 IP address dump code

The current code that dumps the RXIP/VIPA/IPATO addresses via sysfs
first checks whether the buffer still provides sufficient space to hold
another formatted address.
But the maximum length of an formatted IPv4 address is 15 characters,
not 12. So we underestimate the max required length and if the buffer
was previously filled to _just_ the right level, a formatted address can
end up being truncated.

Revamp these code paths to use the _actually_ required length of the
formatted IP address, and while at it suppress a gratuitous newline.

Also use scnprintf() to format the output. In case of a truncation, this
would allow us to return the number of characters that were actually
written.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: replace qeth_l3_get_addr_buffer()

The remaining usage effectively is a kmemdup() of the query object.
By not wrapping it, some of the callers can now use GFP_KERNEL for the
allocation.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: don't cache MAC addresses for multicast IPs

Instead of storing the multicast-mapped MAC address in an IP address
object, just calculate the MAC address when actually building a cmd
for the IP address.

While at it, also clean up some rather verbose copying of IP addresses.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: use helpers for IP address hashing

Replace our custom implementations with the stack's version of IP address
hashing.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qdio: move SSQD Sniffer mask definition

Put the Sniffer bit next to all the other CHSC AC2 bits.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

s390/qeth: shrink qeth_ipaddr struct

Using up 8 bytes in every ipaddr object to store SETIP/DELIP flags is
rather wasteful. Except for takeover eligibility, the flag values all
just depend on the address type, so determine them on demand.

While at it reorder the struct to fill an alignment hole.

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: extract helpers for managing special IPs

Reduce code duplication.

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: restructure IP notification handlers

Extract a helper that does the actual work & returns the right NOTIFY_*
responses, and start putting the temporary ipaddr container objects
on the stack rather than kmalloc'ing them. They are small, and this
reduces the confusion of which objects actually get added to qeth's
IP tables.

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: fix IP address lookup for L3 devices

Current code ("qeth_l3_ip_from_hash()") matches a queried address object
against objects in the IP table by IP address, Mask/Prefix Length and
MAC address ("qeth_l3_ipaddrs_is_equal()"). But what callers actually
require is either
a) "is this IP address registered" (ie. match by IP address only),
before adding a new address.
b) or "is this address object registered" (ie. match all relevant
attributes), before deleting an address.

Right now
1. the ADD path is too strict in its lookup, and eg. doesn't detect
conflicts between an existing NORMAL address and a new VIPA address
(because the NORMAL address will have mask != 0, while VIPA has
a mask == 0),
2. the DELETE path is not strict enough, and eg. allows del_rxip() to
delete a VIPA address as long as the IP address matches.

Fix all this by adding helpers (_addr_match_ip() and _addr_match_all())
that do the appropriate checking.

Note that the ADD path for NORMAL addresses is special, as qeth keeps
track of how many times such an address is in use (and there is no
immediate way of returning errors to the caller). So when a requested
NORMAL address _fully_ matches an existing one, it's not considered a
conflict and we merely increment the refcount.

Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: improve error reporting on IP add/removal

When adding & removing IP entries for rxip/vipa/ipato/hsuid, forward any
resulting errors back to the sysfs-level caller.

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: replace open-coded in*_pton()

There's a common helper for parsing an IP address string, let's use it.

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: use ether_addr_* helpers

Be a little more self-documenting, and get rid of OSA_ADDR_LEN.

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: update takeover IPs after configuration change

Any modification to the takeover IP-ranges requires that we re-evaluate
which IP addresses are takeover-eligible. Otherwise we might do takeover
for some addresses when we no longer should, or vice-versa.

Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/qeth: add support for early L3 device setup

Similar to how qeth currently does early L2 setup of OSM and OSN
devices, add support for early setup of L3-only devices.
This adds a qeth_l3_devtype that contains all core and l3-specific
sysfs attributes, so that they can be created in one go while probing.

This just adds the infrastructure, exploitation of the support happens
in a subsequent patch.

Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: optimize IP handling in rx_mode callback

In layer3 mode of the qeth driver, multicast IP addresses
from struct net_device and other type of IP addresses
from other sources require mapping to the OSA-card.
This patch simplifies the IP address mapping logic, and changes imple-
mentation of ndo_set_rx_mode callback and ip notifier events.
Addresses are stored in private hashtables instead of lists now.
It allows hardware registration/removal for new/deleted multicast
addresses only.

Signed-off-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Evgeny Cherkashin <Eugene.Crosser@ru.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: make local functions static in qeth_l3 module

This patch makes 4 local functions static and removes
the prototypes from the header file.

Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/comments: unify copyright messages and remove file names

Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.

Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>

qeth: add support for af_iucv HiperSockets transport

This patch extends the HiperSockets device driver to send and receive
af_iucv traffic over HiperSockets transport.
TX: Driver uses new asynchronous delivery of storage blocks to pass
flow control/congestion information from the HiperSockets microcode
to the af_iucv socket.
RX: Memory for incoming traffic is preallocated and passed to
HiperSockets layer. If receiver is not capable to clean its buffers
shared with HiperSockets and pass new memory to the HiperSockets
layer this will cause flow control/congestion events on the
sender.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: convert to hw_features part 2

Set rx csum default to hw checksumming again.
Remove sysfs interface for rx csum (checksumming) and TSO (large_send).
With the new hw_features it does not work to keep the old sysfs
interface in parallel. Convert options.checksum_type to new hw_features.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: IP address takeover flag setting

The qeth IP address flag setting is possible when device is
offline. When setting device online afterwards the current set
IP addresses have to be correctly registered with the device
regarding the IP address takeover attribute.

Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: HiperSockets Network Traffic Analyzer

New feature to trace HiperSockets network traffic for debugging
purposes.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: allow dynamic change of rx checksumming

Technically there is no need to set the card offline to change
RX checksumming. Get rid of this stupid limitation.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: rework TSO functions

The maximum TSO size OSA can handle is 15 * PAGE_SIZE. This
patch reduces gso_max_size to this value and adds some sanity
checks and statistics to the TSO implementation.
Since only layer 3 is able to do TSO move all TSO related functions
to the qeth_l3 module.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth module size reduction.

Replace complex macro for s390dbf calls by equivalent function. This reduces
module size about 10% without visible performance impact.

Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

qeth: improving debug message handling

Improving debug message handling, moving ipa into messages from kernel
to dbf, some cleanups and typo fixes.

Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

qeth: new qeth device driver

List of major changes and improvements:
no manipulation of the global ARP constructor
clean code split into core, layer 2 and layer 3 functionality
better exploitation of the ethtool interface
better representation of the various hardware capabilities
fix packet socket support (tcpdump), no fake_ll required
osasnmpd notification via udev events
coding style and beautification

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>