remoteproc: qcom: q6v5: Add interconnect path proxy vote

Many remoteproc instances requires that Linux casts a proxy vote for an
interconnect path during boot, until they can do it themselves. Add
support for voting for a single path.

As this is a shared problem between both PAS and MSS drivers, the path
is acquired and votes casted from the common helper code.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20220225033224.2238425-1-bjorn.andersson@linaro.org

remoteproc: qcom: q6v5: Use qmp_send to update co-processor load state

The power domains exposed by the AOSS QMP driver control the load state
resources linked to modem, adsp, cdsp remoteprocs. These are used to
notify the Always on Subsystem (AOSS) that a particular co-processor is
up/down. AOSS uses this information to wait for the co-processors to
suspend before starting its sleep sequence.

These co-processors enter low-power modes independent to that of the
application processor and the load state resources linked to them are
expected to remain unaltered across system suspend/resume cycles. To
achieve this behavior lets stop using the power-domains exposed by the
AOSS QMP node and replace them with generic qmp_send interface instead.

Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
[bjorn: Fixed up build error in q6v5_wcss_remove()]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631800770-371-5-git-send-email-sibis@codeaurora.org

remoteproc: qcom: q6v5: Query sysmon before graceful shutdown

Requesting a graceful shutdown through the shared memory state signals
will not be acked in the event that sysmon has already successfully shut
down the remote firmware. So extend the stop request API to optionally
take the remoteproc's sysmon instance and query if there's already been
a successful shutdown attempt, before doing the signal dance.

Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

remoteproc: qcom: q6v5: Add common panic handler

Add a common panic handler that invokes a stop request and sleep enough
to let the remoteproc flush it's caches etc in order to aid post mortem
debugging. For now a hard coded 200ms is returned to the remoteproc
core, this value is taken from the downstream kernel.

Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324052904.738594-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

remoteproc: q6v5: Extract common resource handling

Shared between all Hexagon V5 based remoteprocs is the handling of the 5
interrupts and the SMP2P stop request, so break this out into a separate
function in order to allow these drivers to be cleaned up.

Reviewed-by: Rohit kumar <rohitkr@codeaurora.org>
Tested-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>