regulator: tps65086: Select dedicated regulator config for chip variant

Some configurations differ between chip variants, e,g. the register
to control the on of state of LDOA1 and SWB2. Thus, it is necessary
to choose the correct configuration for a dedicated device.
If the wrong configuration was used, the LDOA1 output that was
disabled by the bootloader was enabled in Kernel again.

Each chip variant gets its dedicated configuration selected by
the chip ID previously collected from MFD probe function.
The VTT enum value (tps65086_regulators) is shifted because not all
chip variants have a separate SWB2 switch. Sometimes they are merged.
So the configuration possibilities differ, thus the regulator
configuration arrays have a different length.

Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
Link: https://lore.kernel.org/r/20230818083721.29790-5-andre.werner@systec-electronic.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14

Probing of regulators can be a slow operation and can contribute to
slower boot times. This is especially true if a regulator is turned on
at probe time (with regulator-boot-on or regulator-always-on) and the
regulator requires delays (off-on-time, ramp time, etc).

While the overall kernel is not ready to switch to async probe by
default, as per the discussion on the mailing lists [1] it is believed
that the regulator subsystem is in good shape and we can move
regulator drivers over wholesale. There is no way to just magically
opt in all regulators (regulators are just normal drivers like
platform_driver), so we set PROBE_PREFER_ASYNCHRONOUS for all
regulators found in 'drivers/regulator' individually.

Given the number of drivers touched and the impossibility to test this
ahead of time, it wouldn't be shocking at all if this caused a
regression for someone. If there is a regression caused by this patch,
it's likely to be one of the cases talked about in [1]. As a "quick
fix", drivers involved in the regression could be fixed by changing
them to PROBE_FORCE_SYNCHRONOUS. That being said, the correct fix
would be to directly fix the problem that caused the issue with async
probe.

The approach here follows a similar approach that was used for the mmc
subsystem several years ago [2]. In fact, I ran nearly the same python
script to auto-generate the changes. The only thing I changed was to
search for "i2c_driver", "spmi_driver", and "spi_driver" in addition
to "platform_driver".

[1] https://lore.kernel.org/r/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk
[2] https://lore.kernel.org/r/20200903232441.2694866-1-dianders@chromium.org/

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.1.I2a4677392a38db5758dee0788b2cea5872562a82@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>

treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE

Based on the normalized pattern:

this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is distributed
as is without any warranty of any kind whether expressed or implied
without even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license version 2 for
more details

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference.

Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: tps65086: Constify static regulator_ops

The only usage of reg_ops and switch_ops is to assign their addresses to
the ops field in the regulator_desc struct, which is a const pointer.
Make them const to allow the compiler to put them in read-only memory.

Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200829221104.20870-5-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: Replace HTTP links with HTTPS ones

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.

Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200719200623.61524-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: use linear_ranges helper

Change the regulator helpers to use common linear_ranges code.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/64f01d5e381b8631a271616b7790f9d5640974fb.1588944082.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65086: Fix tps65086_ldoa1_ranges for selector 0xB

selector 0xB (1011) should be 2.6V rather than 2.7V, fit ix.

Table 5-4. LDOA1 Output Voltage Options
VID Bits VOUT VID Bits VOUT VID Bits VOUT VID Bits VOUT
0000 1.35 0100 1.8 1000 2.3 1100 2.85
0001 1.5 0101 1.9 1001 2.4 1101 3.0
0010 1.6 0110 2.0 1010 2.5 1110 3.3
0011 1.7 0111 2.1 1011 2.6 1111 Not Used

Fixes: d2a2e729a666 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65086: Fix DT node referencing in of_parse_cb

When we check for additional DT properties in the current node we
use the device_node passed in with the configuration data, this
will not point to the correct DT node, use the one passed in
for this purpose.

Fixes: d2a2e729a666 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Reported-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65086: Fix expected switch DT node names

The three load switches are called SWA1, SWB1, and SWB2. The
node names describing properties for these are expected to be
the same, but due to a typo they are not. Fix this here.

Fixes: d2a2e729a666 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Reported-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65086: Fix 25mV ranges for BUCK regulators 1, 2, and 6

These regualtors output 0v when vsel is 0. The datasheet will be updated
to reflect this.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

regulator: tps65086: Fix 25mV ranges for BUCK regulators

The BUCK regulators 3, 4, and 5 also have a 10mV step mode,
adjust the tables and logic to reflect the data-sheet for
these regulators.

fixes: d2a2e729a666 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65086: Update regulator driver for the TPS65086 PMIC

Make changes to allow this driver to work with the updated TPS65086 core
driver and bindings.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65086: Add regulator driver for the TPS65086 PMIC

Add support for TPS65086 PMIC regulators.

The regulators set consists of 3 Step-down Controllers, 3 Step-down
Converters, 3 LDOs, 3 Load Switches, and a Sink and Source LDO. The
output voltages are configurable and are meant to supply power to a
SoC and/or other components.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>