platform/x86: int3472: Switch to devm_get_gpiod()

Switch to devm_get_gpiod() for discrete GPIOs for clks / regulators / LEDs
and let devm do the cleanup for us.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20231004162317.163488-5-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>

platform/x86: int3472: Stop using gpiod_toggle_active_low()

Use the new skl_int3472_gpiod_get_from_temp_lookup() helper to get
a gpio to pass to register_gpio_clock(), skl_int3472_register_regulator()
and skl_int3472_register_pled().

This removes all use of the deprecated gpiod_toggle_active_low() and
acpi_get_and_request_gpiod() functions.

Suggested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20231004162317.163488-4-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>

platform/x86: int3472/discrete: set variable skl_int3472_regulator_second_sensor storage-class-specifier to static

smatch reports
drivers/platform/x86/intel/int3472/clk_and_regulator.c:263:28: warning: symbol
'skl_int3472_regulator_second_sensor' was not declared. Should it be static?

This variable is only used in its defining file, so it should be static.

Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20230702134419.3438361-1-trix@redhat.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86: int3472: discrete: Add alternative "AVDD" regulator supply name

Add an "AVDD" regulator supply name alias to the supply-map which
gets registered for the INT3472 GPIO regulator.

This is necessary for the ov2680 driver which expects "AVDD" rather then
"avdd". Updating the ov2680 driver to use "avdd" is not possible because
that will break compatibility with existing DT / DTB files.

Tested-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230616172132.37859-5-hdegoede@redhat.com

platform/x86: int3472: discrete: Add support for 1 GPIO regulator shared between 2 sensors

On the Lenovo Miix 510-12IKB there is 1 GPIO regulator, with its GPIO
listed in the INT3472 device belonging to the OV5648 back sensor.
But this regulator also needs to be enabled for the OV2680 front sensor
to work.

Add support to skl_int3472_register_regulator() to add supply map entries
pointing to both sensors based on a DMI quirk table which gives the
dev_name part of the supply map for the second sensor (the sensor without
the GPIO listed in its matching INT3472 ACPI device).

Tested-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230616172132.37859-4-hdegoede@redhat.com

platform/x86: int3472: discrete: Remove sensor_config-s

Currently the only 2 sensor_config-s both specify "avdd" as supply-id.

The INT3472 device is going to be the only supplier of a regulator for
the sensor device.

So there is no chance of collisions with other regulator suppliers
and it is undesirable to need to manually add new entries to
int3472_sensor_configs[] for each new sensor module which uses
a GPIO regulator.

Instead just always use "avdd" as supply-id when registering
the GPIO regulator.

If necessary for specific sensor drivers then other supply-ids can
be added as aliases in the future, adding aliases will be safe
since INT3472 will be the only regulator supplier for the sensor.

Cc: Bingbu Cao <bingbu.cao@intel.com>
Tested-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230616172132.37859-3-hdegoede@redhat.com

platform/x86: int3472: Evaluate device's _DSM method to control imaging clock

On some platforms, the imaging clock should be controlled by evaluating
specific clock device's _DSM method instead of setting gpio, so this
change register clock if no gpio based clock and then use the _DSM method
to enable and disable clock.

Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Hao Yao <hao.yao@intel.com>
Link: https://lore.kernel.org/r/20230524035135.90315-2-bingbu.cao@intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230531134429.171337-1-hdegoede@redhat.com

platform/x86: int3472: Avoid crash in unregistering regulator gpio

When int3472 is loaded before GPIO driver, acpi_get_and_request_gpiod()
failed but the returned gpio descriptor is not NULL, it will cause panic
in later gpiod_put(), so set the gpio_desc to NULL in register error
handling to avoid such crash.

Signed-off-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Link: https://lore.kernel.org/r/20230524035135.90315-1-bingbu.cao@intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86: int3472/discrete: Get the polarity from the _DSM entry

According to:
https://github.com/intel/ipu6-drivers/blob/master/patch/int3472-support-independent-clock-and-LED-gpios-5.17%2B.patch

Bits 31-24 of the _DSM pin entry integer value codes the active-value,
that is the actual physical signal (0 or 1) which needs to be output on
the pin to turn the sensor chip on (to make it active).

So if bits 31-24 are 0 for a reset pin, then the actual value of the reset
pin needs to be 0 to take the chip out of reset. IOW in this case the reset
signal is active-high rather then the default active-low.

And if bits 31-24 are 0 for a clk-en pin then the actual value of the clk
pin needs to be 0 to enable the clk. So in this case the clk-en signal
is active-low rather then the default active-high.

IOW if bits 31-24 are 0 for a pin, then the default polarity of the pin
is inverted.

Add a check for this and also propagate this new polarity to the clock
registration.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230127203729.10205-6-hdegoede@redhat.com

platform/x86: int3472/discrete: Move GPIO request to skl_int3472_register_clock()

Move the requesting of the clk-enable GPIO to skl_int3472_register_clock()
(and move the gpiod_put to unregister).

This mirrors the GPIO handling in skl_int3472_register_regulator() and
allows removing skl_int3472_map_gpio_to_clk() from discrete.c.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230127203729.10205-5-hdegoede@redhat.com

platform/x86: int3472/discrete: Create a LED class device for the privacy LED

On some systems, e.g. the Lenovo ThinkPad X1 Yoga gen 7 and the ThinkPad
X1 Nano gen 2 there is no clock-enable pin, triggering the:
"No clk GPIO. The privacy LED won't work" warning and causing the privacy
LED to not work.

Fix this by modeling the privacy LED as a LED class device rather then
integrating it with the registered clock.

Note this relies on media subsys changes to actually turn the LED on/off
when the sensor's v4l2_subdev's s_stream() operand gets called.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230127203729.10205-4-hdegoede@redhat.com

platform/x86: int3472/discrete: Ensure the clk/power enable pins are in output mode

acpi_get_and_request_gpiod() does not take a gpio_lookup_flags argument
specifying that the pins direction should be initialized to a specific
value.

This means that in some cases the pins might be left in input mode, causing
the gpiod_set() calls made to enable the clk / regulator to not work.

One example of this problem is the clk-enable GPIO for the ov01a1s sensor
on a Dell Latitude 9420 being left in input mode causing the clk to
never get enabled.

Explicitly set the direction of the pins to output to fix this.

Fixes: 5de691bffe57 ("platform/x86: Add intel_skl_int3472 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20230111201426.947853-1-hdegoede@redhat.com

regulator: core: Use different devices for resource allocation and DT lookup

Following by the below discussion, there's the potential UAF issue
between regulator and mfd.
https://lore.kernel.org/all/20221128143601.1698148-1-yangyingliang@huawei.com/

From the analysis of Yingliang

CPU A |CPU B
mt6370_probe() |
devm_mfd_add_devices() |
|mt6370_regulator_probe()
| regulator_register()
| //allocate init_data and add it to devres
| regulator_of_get_init_data()
i2c_unregister_device() |
device_del() |
devres_release_all() |
// init_data is freed |
release_nodes() |
| // using init_data causes UAF
| regulator_register()

It's common to use mfd core to create child device for the regulator.
In order to do the DT lookup for init data, the child that registered
the regulator would pass its parent as the parameter. And this causes
init data resource allocated to its parent, not itself. The issue happen
when parent device is going to release and regulator core is still doing
some operation of init data constraint for the regulator of child device.

To fix it, this patch expand 'regulator_register' API to use the
different devices for init data allocation and DT lookup.

Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1670311341-32664-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

platform/x86: int3472: Split into 2 drivers

The intel_skl_int3472.ko module contains 2 separate drivers,
the int3472_discrete platform driver and the int3472_tps68470
I2C-driver.

These 2 drivers contain very little shared code, only
skl_int3472_get_acpi_buffer() and skl_int3472_fill_cldb() are
shared.

Split the module into 2 drivers, linking the little shared code
directly into both.

This will allow us to add soft-module dependencies for the
tps68470 clk, gpio and regulator drivers to the new
intel_skl_int3472_tps68470.ko to help with probe ordering issues
without causing these modules to get loaded on boards which only
use the int3472_discrete platform driver.

While at it also rename the .c and .h files to remove the
cumbersome intel_skl_int3472_ prefix.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-8-hdegoede@redhat.com