phy: tegra: xusb: Add Tegra234 support

Add support for the XUSB pad controller found on Tegra234 SoCs. It is
mostly similar to the same IP found on Tegra194, because most of
the Tegra234 XUSB PADCTL registers definition and programming sequence
are the same as Tegra194, Tegra234 XUSB PADCTL can share the same
driver with Tegra186 and Tegra194 XUSB PADCTL.

Introduce a new feature, USB2 HW tracking, for Tegra234.
The feature is to enable HW periodical PAD tracking which measure
and capture the electric parameters of USB2.0 PAD.

Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Co-developed-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230111110450.24617-6-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

phy: tegra: xusb: Add Tegra234 support

Add support for the XUSB pad controller found on Tegra234 SoCs. It is
mostly similar to the same IP found on Tegra194, because most of
the Tegra234 XUSB PADCTL registers definition and programming sequence
are the same as Tegra194, Tegra234 XUSB PADCTL can share the same
driver with Tegra186 and Tegra194 XUSB PADCTL.

Introduce a new feature, USB2 HW tracking, for Tegra234.
The feature is to enable HW periodical PAD tracking which measure
and capture the electric parameters of USB2.0 PAD.

Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Co-developed-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230111110450.24617-6-jonathanh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: tegra: xusb: Add Tegra194 support

Add support for the XUSB pad controller found on Tegra194 SoCs. It is
mostly similar to the same IP found on Tegra186, but the number of
pads exposed differs, as do the programming sequences. Because most of
the Tegra194 XUSB PADCTL registers definition and programming sequence
are the same as Tegra186, Tegra194 XUSB PADCTL can share the same
driver, xusb-tegra186.c, with Tegra186 XUSB PADCTL.

Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
adds a "maximum-speed" property to usb3 ports which can be used to
specify the maximum supported speed for any particular USB 3.1 port.
For a port that is not capable of SuperSpeedPlus, "maximum-speed"
property should carry "super-speed".

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

phy: tegra: Add PCIe PIPE2UPHY support

Synopsys DesignWare core based PCIe controllers in Tegra 194 SoC
interface with Universal PHY (UPHY) module through a PIPE2UPHY (P2U)
module. For each PCIe lane of a controller, there is a P2U unit
instantiated at hardware level. This driver provides support for the
programming required for each P2U that is going to be used for a PCIe
controller.

Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Thierry Reding <treding@nvidia.com>

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

phy: tegra: xusb: Add Tegra186 support

Add support for the XUSB pad controller found on Tegra186 SoCs. It is
mostly similar to the same IP found on earlier chips, but the number of
pads exposed differs, as do the programming sequences.

Note that the DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL power
supplies of the XUSB pad controller require strict power sequencing and
are therefore controlled by the PMIC on Tegra186.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[dan.carpenter@oracle.com: Fix testing the wrong variable in probe()]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[yuehaibing@huawei.com: Make two functions static to fix sparse warning]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

phy: tegra: Add Tegra210 support

Add support for the XUSB pad controller found on Tegra210 SoCs. The
hardware is roughly the same, but some of the registers have been moved
around and the number and type of supported pads has changed.

Signed-off-by: Thierry Reding <treding@nvidia.com>

phy: Add Tegra XUSB pad controller support

Add a new driver for the XUSB pad controller found on NVIDIA Tegra SoCs.
This hardware block used to be exposed as a pin controller, but it turns
out that this isn't a good fit. The new driver and DT binding much more
accurately describe the hardware and are more flexible in supporting new
SoC generations.

Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>