phy: freescale: Add i.MX8qm Mixel LVDS PHY support

Add Freescale i.MX8qm LVDS PHY support.
The PHY IP is from Mixel, Inc.

Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220706034810.2352641-4-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: add support for the Layerscape SerDes 28G

This patch adds a new generic PHY driver to support the Lynx 28G SerDes
block found on some of the Layerscape SoCs such as LX2160A.
At the moment, only the following Ethernet protocols are supported:
SGMII/1000Base-X and 10GBaseR.

SerDes lanes which are not running an Ethernet protocol or a currently
supported Ethenet protocol will be left as it was configured through the
RCW (Reset Configuration Word) at boot time.

At probe time, the platform driver will read the current
configuration of both PLLs found on a SerDes block and will determine
what protocols are supported using that PLL.

For example, if a PLL is configured to generate a clock net (frate) of
5GHz the only protocols sustained by that PLL are SGMII/1000Base-X
(using a quarter of the full clock rate) and QSGMII using the full clock
net frequency on the lane.

On the .set_mode() callback, the PHY driver will first check if the
requested operating mode (protocol) is even supported by the current PLL
configuration and will error out if not.
Then, the lane is reconfigured to run on the requested protocol.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver

Add the standalone i.MX8 PCIe PHY driver.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Link: https://lore.kernel.org/r/1638432158-4119-6-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs

This adds support for the Mixel DPHY as found on i.MX8 CPUs but since
this is an IP core it will likely be found on others in the future. So
instead of adding this to the nwl host driver make it a generic PHY
driver.

The driver supports the i.MX8MQ. Support for i.MX8QM and i.MX8QXP can be
added once the necessary system controller bits are in via
mixel_dphy_devdata.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Co-developed-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

phy: add driver for Freescale i.MX8MQ USB3 PHY

This is a cleaned up port of the downstream i.MX8MQ USB3 PHY driver.

Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>