PCI: rockchip: Use 64-bit mask on MSI 64-bit PCI address

A 32-bit mask was used on the 64-bit PCI address used for mapping MSIs.
This would result in the upper 32 bits being unintentionally zeroed and
MSIs getting mapped to incorrect PCI addresses if the address had any
of the upper bits set.

Replace 32-bit mask by appropriate 64-bit mask.

[kwilczynski: use GENMASK_ULL() over GENMASK() for 32-bit compatibility]
Fixes: dc73ed0f1b8b ("PCI: rockchip: Fix window mapping and address translation for endpoint")
Closes: https://lore.kernel.org/linux-pci/8d19e5b7-8fa0-44a4-90e2-9bb06f5eb694@moroto.mountain
Link: https://lore.kernel.org/linux-pci/20230703085845.2052008-1-rick.wertenbroek@gmail.com
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org

PCI: rockchip: Don't advertise MSI-X in PCIe capabilities

The RK3399 PCIe endpoint controller cannot generate MSI-X IRQs.
This is documented in the RK3399 technical reference manual (TRM)
section 17.5.9 "Interrupt Support".

MSI-X capability should therefore not be advertised. Remove the
MSI-X capability by editing the capability linked-list. The
previous entry is the MSI capability, therefore get the next
entry from the MSI-X capability entry and set it as next entry
for the MSI capability. This in effect removes MSI-X from the list.

Linked list before : MSI cap -> MSI-X cap -> PCIe Device cap -> ...
Linked list now : MSI cap -> PCIe Device cap -> ...

Link: https://lore.kernel.org/r/20230418074700.1083505-11-rick.wertenbroek@gmail.com
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org

PCI: rockchip: Use u32 variable to access 32-bit registers

Previously u16 variables were used to access 32-bit registers, this
resulted in not all of the data being read from the registers. Also
the left shift of more than 16-bits would result in moving data out
of the variable. Use u32 variables to access 32-bit registers

Link: https://lore.kernel.org/r/20230418074700.1083505-10-rick.wertenbroek@gmail.com
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org

PCI: rockchip: Fix window mapping and address translation for endpoint

The RK3399 PCI endpoint core has 33 windows for PCIe space, now in the
driver up to 32 fixed size (1M) windows are used and pages are allocated
and mapped accordingly. The driver first used a single window and allocated
space inside which caused translation issues (between CPU space and PCI
space) because a window can only have a single translation at a given
time, which if multiple pages are allocated inside will cause conflicts.
Now each window is a single region of 1M which will always guarantee that
the translation is not in conflict.

Set the translation register addresses for physical function. As documented
in the technical reference manual (TRM) section 17.5.5 "PCIe Address
Translation" and section 17.6.8 "Address Translation Registers Description"

Link: https://lore.kernel.org/r/20230418074700.1083505-9-rick.wertenbroek@gmail.com
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org

PCI: rockchip: Fix legacy IRQ generation for RK3399 PCIe endpoint core

Fix legacy IRQ generation for RK3399 PCIe endpoint core according to
the technical reference manual (TRM). Assert and deassert legacy
interrupt (INTx) through the legacy interrupt control register
("PCIE_CLIENT_LEGACY_INT_CTRL") instead of manually generating a PCIe
message. The generation of the legacy interrupt was tested and validated
with the PCIe endpoint test driver.

Link: https://lore.kernel.org/r/20230418074700.1083505-8-rick.wertenbroek@gmail.com
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org

PCI: rockchip: Add poll and timeout to wait for PHY PLLs to be locked

The RK3399 PCIe controller should wait until the PHY PLLs are locked.
Add poll and timeout to wait for PHY PLLs to be locked. If they cannot
be locked generate error message and jump to error handler. Accessing
registers in the PHY clock domain when PLLs are not locked causes hang
The PHY PLLs status is checked through a side channel register.
This is documented in the TRM section 17.5.8.1 "PCIe Initialization
Sequence".

Link: https://lore.kernel.org/r/20230418074700.1083505-5-rick.wertenbroek@gmail.com
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org

PCI: rockchip: Write PCI Device ID to correct register

Write PCI Device ID (DID) to the correct register. The Device ID was not
updated through the correct register. Device ID was written to a read-only
register and therefore did not work. The Device ID is now set through the
correct register. This is documented in the RK3399 TRM section 17.6.6.1.1

Link: https://lore.kernel.org/r/20230418074700.1083505-3-rick.wertenbroek@gmail.com
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org

PCI: Add defines for normal and subtractive PCI bridges

Add these PCI class codes to pci_ids.h:

PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE

Use these defines in all kernel code for describing PCI class codes for
normal and subtractive PCI bridges.

[bhelgaas: similar change in pci-mvebu.c]
Link: https://lore.kernel.org/r/20220214114109.26809-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI: Unify ECAM constants in native PCI Express drivers

Add ECAM-related constants to provide a set of standard constants
defining memory address shift values to the byte-level address that can
be used to access the PCI Express Configuration Space, and then move
native PCI Express controller drivers to use the newly introduced
definitions retiring driver-specific ones.

Refactor pci_ecam_map_bus() function to use newly added constants so
that limits to the bus, device function and offset (now limited to 4K as
per the specification) are in place to prevent the defective or
malicious caller from supplying incorrect configuration offset and thus
targeting the wrong device when accessing extended configuration space.

This refactor also allows for the ".bus_shift" initialisers to be
dropped when the user is not using a custom value as a default value
will be used as per the PCI Express Specification.

Thanks to Qian Cai <qcai@redhat.com>, Michael Walle <michael@walle.cc>,
and Vladimir Oltean <olteanv@gmail.com> for reporting a pci_ecam_create()
issue with .bus_shift and to Vladimir for proposing the fix.

[bhelgaas: incorporate Vladimir's fix, update commit log]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-2-kw@linux.com
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>

PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus

Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.

Also, bridge->busnr is never set so effectively the root bus must be 0.
This will be fixed by a subsequent commit.

Link: https://lore.kernel.org/r/20200722022514.1283916-10-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org

PCI: rockchip: Use pci_host_probe() to register host

The rockchip host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.

Link: https://lore.kernel.org/r/20200522234832.954484-14-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org

x86/PCI: Correct SPDX comment style

Change:

drivers/pci/controller/pcie-cadence.h
drivers/pci/controller/pcie-rockchip.h

to use the correct SPDX comment style per section 2 of
Documentation/process/license-rules.rst.

These resolve the following checkpatch.pl warning:

WARNING: Missing or malformed SPDX-License-Identifier tag in line 1

[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20190828135322.10370-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI: rockchip: Drop storing driver private outbound resource data

The Rockchip host bridge driver doesn't need to store outboard resources
in its private struct as they are already stored in struct
pci_host_bridge.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org

PCI: Collect all native drivers under drivers/pci/controller/

Native PCI drivers for root complex devices were originally all in
drivers/pci/host/. Some of these devices can also be operated in endpoint
mode. Drivers for endpoint mode didn't seem to fit in the "host"
directory, so we put both the root complex and endpoint drivers in
per-device directories, e.g., drivers/pci/dwc/, drivers/pci/cadence/, etc.

These per-device directories contain trivial Kconfig and Makefiles and
clutter drivers/pci/. Make a new drivers/pci/controllers/ directory and
collect all the device-specific drivers there.

No functional change intended.

Link: https://lkml.kernel.org/r/1520304202-232891-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>