wifi: rtw89: wow: update config mac function with different generation

The registers to configure mac function for WoWLAN mode that are different
from different generation, so update them.

Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-5-pkshih@realtek.com

wifi: rtw89: wow: update WoWLAN status register for different generation

The statue register is for driver to check if WoWLAN mode works or stops
successfully. It is changed for new generation, so update it.

Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-3-pkshih@realtek.com

wifi: rtw89: 8922a: add coexistence helpers of SW grant

Under some circumstances, coexistence mechanism want to keep grant BT or
WiFi, such as inquiry and WiFi is connecting, to ensure BT or WiFi can
transmit or receive data in that period.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-3-pkshih@realtek.com

wifi: rtw89: mac: add coexistence helpers {cfg/get}_plt

When hardware grant BT initially but transition to grant WiFi, the PLT
(polluted) bit is set to assist coexistence mechanism to debug if
grant signal is expected.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-2-pkshih@realtek.com

wifi: rtw89: reference quota mode when setting Tx power

Reference the current quota mode to avoid misleading warnings.
This patch is required after supporting DBCC quota mode.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-11-pkshih@realtek.com

wifi: rtw89: 8922a: implement AP mode related reg for BE generation

Modify reg for BE generation when AP stop, otherwise have warning
messages "Polling beacon packet empty fail".

Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-10-pkshih@realtek.com

wifi: rtw89: differentiate narrow_bw_ru_dis setting according to chip gen

When there are OBSS that cannot interpret 26-tone RU transmissions,
we should disable 26-tone RU HE TB PPDU transmissions. So, add registers
accordingly.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-8-pkshih@realtek.com

wifi: rtw89: use PLCP information to match BSS_COLOR and AID

Hardware can use spatial reuse to reduce interference in OBSS environment,
and originally use MAC header to match BSS color and AID. Change to use
PLCP to match them earlier to prevent margin timing.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-7-pkshih@realtek.com

wifi: rtw89: mac: reset PHY-1 hardware when going to enable/disable

When going to use PHY-1, reset the hardware to make it work properly.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-6-pkshih@realtek.com

wifi: rtw89: mac: correct MUEDCA setting for MAC-1

Consider mac_idx as an argument to set this register to disable QoS NULL
update MUEDCA timer.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-5-pkshih@realtek.com

wifi: rtw89: mac: return held quota of DLE when changing MAC-1

DLE (data link engine) could hold quota when we are going to enable/disable
MAC-1 block, so trigger hardware to return all held quota.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-4-pkshih@realtek.com

wifi: rtw89: update ps_state register for chips with different generation

The ps_state register is used for driver to check if the WiFi chip leave
power save mode successfully. The register is changed for new generation,
so update it.

Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126063356.17857-7-pkshih@realtek.com

wifi: rtw89: 8922a: add ieee80211_ops::hw_scan

This adds support for hardware scan after FW version 0.34.35. Currently
we only support scanning on single hardware band and support of dual band
scan will be added in the future. Adjust the current flow to make driver
compatible with different generation ICs.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126063356.17857-5-pkshih@realtek.com

wifi: rtw89: prepare scan leaf functions for wifi 7 ICs

The channel field slightly differs between WiFi 6 and WiFi 7.
So we prepare some required functions in advance, this doesn't change
existing wifi 6 ICs behavior. This H2C prepares the channel list
to be scanned for. With layout as the following:

+--------+--------------------+-------------------+-----------------------+
| header | number of channels | channel info size | channel_info * number |
+--------+--------------------+-------------------+-----------------------+

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126063356.17857-4-pkshih@realtek.com

wifi: rtw89: 8922a: implement {stop,resume}_sch_tx and cfg_ppdu

To set TX/RX path or set channel, we need these helpers to stop TX and
restore settings. The sch_tx stands for scheduler TX channel, and the
cfg_ppdu is to stop reporting PPDU status, so we should stop them during
setting.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033637.12330-3-pkshih@realtek.com

wifi: rtw89: mac: Fix spelling mistakes "notfify" -> "notify"

There are two spelling mistakes in rtw89_err error messages. Fix these
and also add space between [ERR] and message text.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231220141831.10063-1-colin.i.king@gmail.com

wifi: rtw89: mac: implement to configure TX/RX engines for WiFi 7 chips

After enabling DMAC and CMAC, configure detail registers one by one.
DMAC includes DLE (data link engine), packet preload engine, HFC (HCI
flow control) for DMA channels, security egine and etc. CMAC includes
scheduler, address CAM, RX filter, CCA control and etc.

The SER IMR is to configure to help SER. When hardware TX/RX get
abnormal, it raises an interrupt to firmware to determine if send C2H
events to notify driver to reset PCI bus or call ieee80211_restart_hw().

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231216045739.10432-3-pkshih@realtek.com

wifi: rtw89: mac: add sys_init and filter option for WiFi 7 chips

The sys_init is to enable hardware function block of DMAC (data-path MAC),
CMAC (control-path MAC) and others called 'chip_func'. To understand the
functionality of this function, we keep some functions as empty.

The other is typ_fltr_opt that is to configure filter option to decide
whether RX packets engine can forward packets to host or WiFi CPU.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231216045739.10432-2-pkshih@realtek.com

wifi: rtw89: mac: add flags to check if CMAC and DMAC are enabled

Before accessing CMAC and DMAC registers, we should ensure they have been
powered on, so add flag to determine the state. For old chips, we read
registers and check corresponding bit, but it takes extra cost to read.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-4-pkshih@realtek.com

wifi: rtw89: add XTAL SI for WiFi 7 chips

The XTAL SI is a serial interface to indirectly access registers of
analog hardware circuit. Since WiFi 7 chips use different registers, add
a ops to access them via common functions. This patch doesn't change logic
for existing chips.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-2-pkshih@realtek.com

wifi: rtw89: mac: refine SER setting during WiFi CPU power on

Don't enable firmware debug mode to prevent SER flow stuck due to fail
to reset payload buffer, and clear HALT_C2H_INT to avoid handling
unexpected interrupt at beginning.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-6-pkshih@realtek.com

wifi: rtw89: 8922a: dump MAC registers when SER occurs

To diagnose the reason why firmware or hardware get abnormal, add to dump
MAC registers related to counters and interrupt masks. With these values,
people can classify problems and check if registers values are unexpected,
and then correct them. However, it could possible false alarm because
firmware triggers this SER event by wrong conditions that we should
correct it at firmware or register settings.

In field, SER might happen under special conditions, and very hard to
happen again, so dump lots of registers to provide rich information to
catch the problem.

Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-5-pkshih@realtek.com

wifi: rtw89: mac: functions to configure hardware engine and quota for WiFi 7 chips

Add functions to configure HCI, DMAC (data MAC), DLE (data link engine),
HFC (HCI flow control), PLE (payload engine) and etc for WiFi 7 chips.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124071703.132549-9-pkshih@realtek.com

wifi: rtw89: mac: check queue empty according to chip gen

This function, currently called by WoWLAN flow, polls until specific HW
queues are empty. The polling bit definitions are not totally the same
between WiFi 6 and 7 chips. In addition, the check conditions are also
a little different. So, we differentiate the implementations according to
chip gen.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124071703.132549-6-pkshih@realtek.com

wifi: rtw89: mac: add to access efuse for WiFi 7 chips

MAC address, hardware type, calibration values and etc are stored in efuse,
so we read them at probe stage and use them as capabilities to register
hardware.

There are two physical efuse -- one is the main efuse for digital hardware
part, and the other is for analog part. Because they are very similar, we
only describe the main efuse below.

The main efuse is split into two regions -- one is for logic map, and the
other is for physical map. For both regions, we use the same method to read
data, but need additional parser to get logic map. To allow reading
operation, we need to convert power state to active, and turn to idle state
after reading.

For WiFi 7 chips, we introduce efuse blocks to define feature group easier,
and these blocks are discontinue. For example, RF block is from 0x1_0000 ~
0x1_0240, and the next block PCIE_SDIO is starting from 0x2_0000.
Comparing to old one used by WiFi 6 chips, there is only single one logic
map, it would be a little hard to add an new field to a group if we don't
reserve a room in advance.

The relationship between efuse, region and block is shown as below:

(logical map)
+------------+ +---------------+ +-----------------+
| main efuse | | region 1 | | block 0x1_0000~ |
| (digital) | |(to logcal map)| +-----------------+
| | | | => +-----------------+
| | => | | | block 0x2_0000~ |
| | | | +-----------------+
| | |---------------| :
| | | region 2 |
+------------+ +---------------+

+------------+ +-----------------+
| 2nd efuse | ======================> | block 0x7_0000~ |
| (analog) | +-----------------+
+------------+

The parser converting from raw data to logic map is to decode block page,
block page offset, and word_en bits. Each word_en bit indicates two
following bytes as data of logic map, so total four word_en bits can
represent eight bytes. Thus, block page offset is 8-byte alignment.
The layout of a tuple is shown as below

+--------+--------+--------+--------+--------+--------+
| fixed 3 byte header | | | |
| | | | |
| [19:17] block_page | | | ... |
| [16:4] block_page_offset| | | |
| [3:0] word_en | ^ | ^ | |
+----|---+--------+--------+---|----+----|---+--------+
| | |
+-------------------------+---------+
a word_en bit indicates two bytes as data

For example,
block_page = 0x3
block_page_offset = 0x80 (must 8-byte alignment)
word_en = 0x6 (b'0110; 0 means data is presented)
following 4 bytes = 34 56 78 90
Then,
0x3_0080 = 34 56
0x3_0086 = 78 90

A special block page is RTW89_EFUSE_BLOCK_ADIE (7) that uses different
but similar format, because its real efuse size is smaller than main efuse.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231117024029.113845-4-pkshih@realtek.com

wifi: rtw89: mac: set bf_assoc capabilities according to chip gen

When associated peer has beamformer capability, we should enable
beamformee, set CSI parameter, and configure rate to send CSI packets.
Since registers of WiFi 7 chips are very different from existing chips,
separate configuration functions.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-6-pkshih@realtek.com

wifi: rtw89: mac: set bfee_ctrl() according to chip gen

When associated peer has beamformer capability, enable hardware beamformee
function, and then hardware can run sounding protocol itself. Oppositely,
disable this function when disassociated. Define different registers for
WiFi 6 and 7 generations respectively.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-5-pkshih@realtek.com

wifi: rtw89: mac: generalize register of MU-EDCA switch according to chip gen

When connected with 802.11ax AP, MU-EDCA parameters are given, so enable
this hardware function by registers according to chip generation.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-3-pkshih@realtek.com

wifi: rtw89: mac: update RTS threshold according to chip gen

When TX size or time of packet over RTS threshold set by this register,
hardware will use RTS protection automatically. Since WiFi 6 and 7 chips
have different register address for this, separate the address according
to chip gen.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-2-pkshih@realtek.com

wifi: rtw89: mac: get TX power control register according to chip gen

There are two difference between Wi-Fi 6 and Wi-Fi 7 chips.
1. Address range of TX power control register
2. Checking code to get a TX power control register

So, separate the implementation of them, access according to
chip generation, and rename original things with a suffix `_ax`.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-2-pkshih@realtek.com

wifi: rtw89: add mac_gen pointer to access mac port registers

Using mac_gen pointer to reuse the code with WiFi 7 chips, and define
MAC ports registers for WiFi 7 chips.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230911082049.33541-7-pkshih@realtek.com

wifi: rtw89: fw: propagate an argument include_bb for BB MCU firmware

Though WiFi 7 chips need BB MCU firmware, we don't download it in probe
stage. Instead, only bring interface up under normal operation or WoWLAN
mode. So, add an argument to assist download flow to setup download
settings properly.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-6-pkshih@realtek.com

wifi: rtw89: fw: add checking type for variant type of firmware

For WiFi 6 chips, there is only single one firmware i.e. WiFi CPU firmware,
so no need an argument to discriminate them. For WiFi 7 chips, BB MCU
firmware is introduced, and we need to check it ready after downloading.

For each type of firmware, we need to check corresponding hardware ready
bit. After downloading all firmware, check status code to determine if
all things are ready.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-5-pkshih@realtek.com

wifi: rtw89: fw: implement supported functions of download firmware for WiFi 7 chips

To work with generalized flow of download firmware, implement WiFi 7
specific functions to support it. These functions include disable/enable
WiFi CPU, status of path ready, and status of firmware.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-4-pkshih@realtek.com

wifi: rtw89: mac: define register address of rx_filter to generalize code

rx_filter is used to decide which kind of packets are received to driver,
or just dropped by MAC layer to reduce bus traffic.

The bit definitions of old and new chips are the sames, but only address
is changed, so define a field to generalize usage.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-5-pkshih@realtek.com

wifi: rtw89: mac: define internal memory address for WiFi 7 chip

Define base address of WiFi 7 internal memory according to design to
provide the same functions as existing WiFi 6 chips.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-4-pkshih@realtek.com

wifi: rtw89: mac: add mac_gen_def::band1_offset to map MAC band1 register address

There are two copies of MAC hardware called band0 and band1. Basically,
the only difference between them is base address, so we can share functions
with a 'band' (or 'mac_idx') argument.

The offset of base address of WiFi 6 and 7 are 0x2000 and 0x4000
respectively, so add band1_offset field to new introduced struct
mac_gen_def to possibly reuse functions.

Using below spatch script to convert callers:

@@
expression reg, band;
@@
- rtw89_mac_reg_by_idx(reg, band)
+ rtw89_mac_reg_by_idx(rtwdev, reg, band)

@@
expression reg, port, band;
@@
- rtw89_mac_reg_by_port(reg, port, band)
+ rtw89_mac_reg_by_port(rtwdev, reg, port, band)

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-2-pkshih@realtek.com