wifi: rtw89: chan: tweak weight recalc ahead before MLO

Originally, we consider weight only based on how many chanctxs that
mac80211 sets. However, we need to consider both active chanctxs and
active interfaces to distinguish MCC (multiple channel concurrent)
from impending MLO.

Although the logic of handling is extended, for now, behavior might
not be different under current condition.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240206030624.23382-5-pkshih@realtek.com

wifi: rtw89: pause/proceed MCC for ROC and HW scan

During (TDMA-based) MCC (multi-channel concurrency), the below two
cases might not have a good behavior on channel usage.
* ROC (remain on channel)
* HW scan
So, we tend to separate them from MCC.

The two cases would expect to operate the channel to which they want.
However, during MCC, channels are scheduled by FW MCC state mechanism.
So, channels cannot be controlled explicitly. To avoid the two cases
from operating wrong channels with chance, we pause MCC (essentially
stop FW MCC) once the two cases are coming. And then, we proceed MCC
again (essentially restart FW MCC) once the two cases finish.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230921003559.11588-3-pkshih@realtek.com

wifi: rtw89: mcc: track beacon offset and update when needed

In MCC STA+GC mode, the offset between TBTTs of remote AP and remote GO
might change. If the change is larger than tolerance, we should update
MCC after re-calculating parameters for new things. So, we track that in
rtw89_track_work() now. And, we add MCC update flow to tell FW either to
change durations of roles or to replace entire pattern according to how
MCC plans BT slot.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-6-pkshih@realtek.com

wifi: rtw89: mcc: update role bitmap when changed

Each MCC (multi-channel concurrency) role maintains a bitmap of mac IDs.
The bitmap is supposed to contain the two points below.
* mac ID of itself
* mac ID(s) of STA(s) connecting to it
Under STA+GC mode, the bitmaps of both roles should not change. However,
under STA+GO mode, the bitmap of GO may change due to P2P clients which
connect/disconnect to/from it.

FW controls (TDMA-based) MCC things via mac IDs in bitmap of each role.
For example, mac IDs are required by FW when it wants to pause role1's
TX in role0 slot.

So, to sync between driver and FW, we update the new mac ID bitmap of GO
to FW once it's changed.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-5-pkshih@realtek.com

wifi: rtw89: mcc: fill fundamental configurations

We determine the fundamental settings shown below.

|< MCC interval >|
|< duration ref >|< duration aux >|
| | | |
|< beacon offset >|
| |
V V
(tbtt ref) (tbtt aux)

(where `ref` (reference) and `aux` (auxiliary) mean the two MCC roles)

Based on MCC mode (GO+STA or GC+STA), we fill configurations of
MCC interval and beacon offset. And, we make sure each MCC role
have a basically required duration in the MCC interval.

The beacon offset mentioned above is a parameter for further MCC
pattern calculation. If MCC is in GC+STA mode, we will calculate
the real beacon offset through TSFs shown in beacons of both MCC
roles. Otherwise, we will use a default beacon offset, and make
GO sync STA's TSF timer with this offset.

MCC pattern calculation will break down each MCC role's duration
in more detail. We will implement it in the following.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-3-pkshih@realtek.com

wifi: rtw89: mcc: initialize start flow

We prepare to support TDMA-based MCC (multi-channel concurrency)
which allows two kinds of modes below.
* P2P GO + normal STA
* P2P GC + normal STA

Each mode has two vif and two chanctx. Then, each vif binds one
separate chanctx and becomes one MCC role. We name the two MCC
roles as follows.
* MCC role - reference (ref)
We calculate the baseline of our TDMA things accodring
to its info, e.g. TBTT. In normal case, it will be put
at the first slot of TDMA.
* MCC role - auxiliary (aux)

MCC state machine will be running in FW eventually, but before that,
we have to fill and calculate things that are needed by FW. We fill
the information of MCC role according to its vif and its chanctx.
Then, we calculate the start time for MCC.

Note that the parameters used in the calculation now is assigned by
default rules. The precise parameters for better MCC behavior will be
derived in the following.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-2-pkshih@realtek.com

wifi: rtw89: initialize multi-channel handling

We prepare to deal with multiple channels via new entity modes.
* MCC_PREPARE: Transitional mode before MCC
* MCC: Multi-Channel Concurrent mode
And, enum of sub-entity is extended for second channel context.

We add the entry flow of multi-channel handling and the core stuffs
for extended index of sub-entity. And, we now deal with the filling
of entity channels' info in entity recalc where we know the number
of active chanctx. However, the other detail coding of MCC start/stop
will be implemented in the following.

Besides, chanctx listener struct is pre-added in chip info. Each
component can add callback type in chanctx listener and configure
its callback function to react according to chanctx states. We know
at least RFK (RF calibration) and BTC (BT coexistence) will require
such callbacks.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-7-pkshih@realtek.com

wifi: rtw89: add ieee80211::remain_on_channel ops

Add support of remain on channel ops. Since channel context is
required to enable multi-channel concurrent(MCC) and the current
ROC in mac80211 don't support more than 1 channel context, add this
to let P2P and other protocols relying on this work as expected.
The off-channel duration and cancel timing is purely controlled by
upper layers.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-4-pkshih@realtek.com

wifi: rtw89: add skeleton of mac80211 chanctx ops support

Support mac80211 chanctx series ops. Still, currently support
single channel. Based on this premise, things should be similar
to before. So, we haven't dealt with relationship between vif
and chanctx in depth. Instead, we leave both ::assign_vif()
and ::unassign_vif() as noops for now.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-12-pkshih@realtek.com

wifi: rtw89: introduce entity mode and its recalculated prototype

After supporting more than one channel, we need entity mode to decide
how to set current channel(s) on the sub-entities. This decision may
happen on set_channel() and rtw89_core_set_chip_txpwr().

For now, we support single one channel and use only first HW entry,
i.e. RTW89_SUB_ENTITY_0, RTW89_MAC_0, RTW89_PHY_0. Without something
unexpected, the entity mode should always be RTW89_ENT_MODE_SCC after
recalcated, where SCC means single channel concurrency. So, an assert
is added in set_channel() and rtw89_core_set_chip_txpwr().

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-11-pkshih@realtek.com

wifi: rtw89: initialize entity and configure default chandef

While idle, we need a default chandef to set channel for things,
such as scan. Before support of mac80211 chanctx, mac80211 would
configure a default one on ieee80211_hw::conf::chandef. And we
just queried it whenever we did set channel. However, after support
of mac80211 chanctx, the flow won't work like before.

Besides, we don't now query chandef from ieee80211_hw::conf::chandef
either. So, similar to mac80211 without using chanctx, we configure
the default chandef with ieee80211_channel of index 0 in 2GHz.

Although we have not added the support of mac80211 chanctx here,
this configuration should be compatible before that. So, we commit
this ahead.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-10-pkshih@realtek.com

wifi: rtw89: concentrate chandef setting to stack callback

Originally, we didn't support mac80211 chanctx, so it's expected that
ieee80211_hw::conf::chandef would be filled by mac80211. And then, we
could just query it whenever we need the current chandef.

However, we are planing to support mac80211 chanctx. After that, the
above assumption would be broken. So, we adjust a bit ahead to reduce
future works about mac80211 chanctx.

After this, we don't query ieee80211_hw::conf::chandef directly, and
we add a map, entity_map, to HAL to indicate which chandef came from
stack. And it will later be used to recalcate entity mode.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-9-pkshih@realtek.com

wifi: rtw89: create rtw89_chan centrally to avoid breakage

Sometimes we need to write current rtw89_chan outside set_channel(),
e.g. during HW scan, we adjust it to align FW process through C2H.
However, we don't have full parameters to fill entire rtw89_chan.
And it will breakage if we update only part of current rtw89_chan.
That is what we don't want to see because most flows throughout
driver treat rtw89_chan as a whole.

So, we divide struct rtw89_chan to basic part and derived part. The
basic part contains the parameters which we are always able to know.
And the derived part will be calculated by the basic part. Then, a
central function, rtw89_chan_create(), is added to deal with this.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-5-pkshih@realtek.com

wifi: rtw89: re-arrange channel related stuffs under HAL

We are planning to support mac80211 chanctx. To reduce future works,
the driver architecture is adjusted first to isolate related things.

According to chip, our HW may have multiple sub-entities to support
multiple mac80211 chanctx. Struct rtw89_chan has been introduced for
things about channel/band/subband/... Now introduce struct rtw89_chan_rcd
to record difference after assigning new one of struct rtw89_chan.

We will implement and support chanctx with single channel first, i.e.
only use entry in RTW89_SUB_ENTITY_0, before handling dual channels.

Our hierarchy in planning will become as the following.
DEV
-> HAL
---> entity (manage status across sub-entities)
-----> sub-entity[*] (support mac80211 chanctx)
where each sub-entity contains one struct rtw89_chan.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-4-pkshih@realtek.com

wifi: rtw89: rewrite decision on channel by entity state

We need to invoke the callback of the changed band at the first
set_channel() after every power-off. Originally, we forced the
channel to be 0 when doing power-off, and then determined things
by comparing channel with 0.

However, deciding on such things by channel might be confusing.
It's also confusing to use this kind of decision when we consider
multiple channels in the follow-up patches. So, another flag,
entity_active, is added ahead to HAL to deal with this.

Besides, we also need to check if entity is active when we set
TX power.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-2-pkshih@realtek.com