wifi: rtw88: 8821cu: Fix connection failure

Clear bit 8 of REG_SYS_STATUS1 after MAC power on.

Without this, some RTL8821CU and RTL8811CU cannot connect to any
network:

Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 1/3)
Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 2/3)
Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 3/3)
Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with
90:55:de:__:__:__ timed out

The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do
it for all three types of chips.

Tested with RTL8811CU (Tenda U9 V2.0).

Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/aeeefad9-27c8-4506-a510-ef9a9a8731a4@gmail.com

wifi: rtw88: add missing unwind goto for __rtw_download_firmware()

This flaw is detected by smatch:
drivers/net/wireless/realtek/rtw88/mac.c:748 __rtw_download_firmware()
warn: missing unwind goto?

Though most things of dlfw_fail have been done by
download_firmware_end_flow() and wlan_cpu_enable(), an exception is that
download_firmware_end_flow() clear BIT_MCUFWDL_EN bit conditionally.
So, make this change to clear the bit.

Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202306052310.OVhcUjZ3-lkp@intel.com/
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230607012741.10353-1-pkshih@realtek.com

wifi: rtw88: 8822c: extend reserved page number

Extend 8822c's reserved page number to accommodate additional required
pages. Reserved page is an area of memory in the FIFO dedicated for
special purposes. Previously only one interface is supported so 8 pages
should suffice, extend it so we can support 2 interfaces concurrently.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-4-pkshih@realtek.com

wifi: rtw88: mac: Support SDIO specific bits in the power on sequence

Add the code specific to SDIO HCI in the MAC power on sequence. This is
based on the RTL8822BS and RTL8822CS vendor drivers.

Co-developed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-4-martin.blumenstingl@googlemail.com

wifi: rtw88: sdio: Add HCI implementation for SDIO based chipsets

Add a sub-driver for SDIO based chipsets which implements the following
functionality:
- register accessors for 8, 16 and 32 bits for all states of the card
(including usage of 4x 8 bit access for one 32 bit buffer if the card
is not fully powered on yet - or if it's fully powered on then 1x 32
bit access is used)
- checking whether there's space in the TX FIFO queue to transmit data
- transfers from the host to the device for actual network traffic,
reserved pages (for firmware download) and H2C (host-to-card)
transfers
- receiving data from the device
- deep power saving state

The transmit path is optimized so DMA-capable SDIO host controllers can
directly use the buffers provided because the buffer's physical
addresses are 8 byte aligned.

The receive path is prepared to support RX aggregation where the
chipset combines multiple MAC frames into one bigger buffer to reduce
SDIO transfer overhead.

Co-developed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-3-martin.blumenstingl@googlemail.com

wifi: rtw88: Clear RTW_FLAG_POWERON early in rtw_mac_power_switch()

The SDIO HCI implementation needs to know when the MAC is powered on.
This is needed because 32-bit register access has to be split into 4x
8-bit register access when the MAC is not fully powered on or while
powering off. When the MAC is powered on 32-bit register access can be
used to reduce the number of transfers but splitting into 4x 8-bit
register access still works in that case.

During the power on sequence is how RTW_FLAG_POWERON is only set when
the power on sequence has completed successfully. During power off
however RTW_FLAG_POWERON is set. This means that the upcoming SDIO HCI
implementation does not know that it has to use 4x 8-bit register
accessors. Clear the RTW_FLAG_POWERON flag early when powering off the
MAC so the whole power off sequence is processed with RTW_FLAG_POWERON
unset. This will make it possible to use the RTW_FLAG_POWERON flag in
the upcoming SDIO HCI implementation.

Note that a failure in rtw_pwr_seq_parser() while applying
chip->pwr_off_seq can theoretically result in the RTW_FLAG_POWERON
flag being cleared while the chip is still powered on. However,
depending on when the failure occurs in the power off sequence the
chip may be on or off. Even the original approach of clearing
RTW_FLAG_POWERON only when the power off sequence has been applied
successfully could end up in some corner case where the chip is
powered off but RTW_FLAG_POWERON was not cleared.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-2-martin.blumenstingl@googlemail.com

wifi: rtw88: mac: Return the original error from rtw_mac_power_switch()

rtw_mac_power_switch() calls rtw_pwr_seq_parser() which can return
-EINVAL, -EBUSY or 0. Propagate the original error code instead of
unconditionally returning -EINVAL in case of an error.

Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230226221004.138331-3-martin.blumenstingl@googlemail.com

wifi: rtw88: mac: Return the original error from rtw_pwr_seq_parser()

rtw_pwr_seq_parser() calls rtw_sub_pwr_seq_parser() which can either
return -EBUSY, -EINVAL or 0. Propagate the original error code instead
of unconditionally returning -EBUSY in case of an error.

Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230226221004.138331-2-martin.blumenstingl@googlemail.com

wifi: rtw88: mac: Add SDIO HCI support in the TX/page table setup

txdma_queue_mapping() and priority_queue_cfg() can use the first entry
of each chip's rqpn_table and page_table. Add this mapping so data
transmission is possible on SDIO based chipsets.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230218152944.48842-3-martin.blumenstingl@googlemail.com

wifi: rtw88: mac: Add support for the SDIO HCI in rtw_pwr_seq_parser()

rtw_pwr_seq_parser() needs to know about the HCI bus interface mask for
the SDIO bus so it can parse the chip state change sequences.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230218152944.48842-2-martin.blumenstingl@googlemail.com

wifi: rtw88: use RTW_FLAG_POWERON flag to prevent to power on/off twice

Use power state to decide whether we can enter or leave IPS accurately,
and then prevent to power on/off twice.

The commit 6bf3a083407b ("wifi: rtw88: add flag check before enter or leave IPS")
would like to prevent this as well, but it still can't entirely handle all
cases. The exception is that WiFi gets connected and does suspend/resume,
it will power on twice and cause it failed to power on after resuming,
like:

rtw_8723de 0000:03:00.0: failed to poll offset=0x6 mask=0x2 value=0x2
rtw_8723de 0000:03:00.0: mac power on failed
rtw_8723de 0000:03:00.0: failed to power on mac
rtw_8723de 0000:03:00.0: leave idle state failed
rtw_8723de 0000:03:00.0: failed to leave ips state
rtw_8723de 0000:03:00.0: failed to leave idle state
rtw_8723de 0000:03:00.0: failed to send h2c command

To fix this, introduce new flag RTW_FLAG_POWERON to reflect power state,
and call rtw_mac_pre_system_cfg() to configure registers properly between
power-off/-on.

Reported-by: Paul Gover <pmw.gover@yahoo.co.uk>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217016
Fixes: 6bf3a083407b ("wifi: rtw88: add flag check before enter or leave IPS")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230216053633.20366-1-pkshih@realtek.com

wifi: rtw88: mac: Use existing macros in rtw_pwr_seq_parser()

Replace the magic numbers for the intf_mask with their existing
RTW_PWR_INTF_PCI_MSK and RTW_PWR_INTF_USB_MSK macros to make the code
easier to understand.

Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230204233001.1511643-5-martin.blumenstingl@googlemail.com

wifi: rtw88: Add common USB chip support

Add the common bits and pieces to add USB support to the RTW88 driver.
This is based on https://github.com/ulli-kroll/rtw88-usb.git which
itself is first written by Neo Jou.

Signed-off-by: neo_jou <neo_jou@realtek.com>
Signed-off-by: Hans Ulli Kroll <linux@ulli-kroll.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202081224.2779981-8-s.hauer@pengutronix.de

wifi: rtw88: 8821c: enable BT device recovery mechanism

8821ce is a combo card, and BT is a USB device that could get card lost
during stress test, and need WiFi firmware to detect and recover it, so
driver sends a H2C to enable this mechanism.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221128075653.5221-1-pkshih@realtek.com

wifi: rtw88: access chip_info by const pointer

Since chip_info has became const table, we must access them via const
pointer to avoid invalid writing.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065232.28510-1-pkshih@realtek.com

rtw88: use the correct bit in the REG_HCI_OPT_CTRL register

Write the BIT_USB_SUS_DIS bit rather than BIT_BT_DIG_CLK_EN to the
REG_HCI_OPT_CTRL register for fixing failure to PCIe power on.

Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/YmLAzuyPr0P4Y6BP@ns.kevlo.org

rtw88: 8822c: support FW crash dump when FW crash

Although FW crash logs are already supported for dumping in driver, the
logs may not be sufficient to analyze field issues. To improve this part,
we add a support to dump FW memory.

When driver receives FW crash notifications, driver uses DDMA, which is a
HW ability, to copy specified FW memory to FW fifo. Driver can then dump
these information from FW fifo. With this support, not only FW crash log
but also specified FW memory will be dumped while FW crash. Besides,
specified registers are also dumped.

This feature is implemeted on 8822C first due to difference of FW layouts
between ICs. In addition, we add a debugfs to trigger FW crash. It can
simulate the process of crash, dump and reset. Through it, we can also
check if a reset is ongoing.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210309060121.9099-1-pkshih@realtek.com

rtw88: use read_poll_timeout_atomic() for poll loop

This gives the added bonus of not wasting an extra udelay() if we're
timing out -- we double-check the register state one last time before
returning.

Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821235733.1785009-1-briannorris@chromium.org

rtw88: extract: export symbols used in chip functionalities

In the current design, various chip functions and tables
are built into rtw88 core. That causes kernel to load its
functionalities even if a chip isn't currently used. We
plan to make each chip's functionalities a separate
kernel module to reduce rtw88 core. And kernel will be
able to load the necessary.

Before extracting chip functionalities, we export symbols
inside rtw88 core which will be used in chip modules.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-2-yhchuang@realtek.com

rtw88: 8723d: implement flush queue

Flush queue is used to check if queue is empty, before doing something
else. Since 8723D uses different registers and page number of
availabl/reserved occupy 8 bits instead of 16 bits, so use a 'wsize' field
to discriminate which rtw_read{8,16} is adopted.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-6-yhchuang@realtek.com

rtw88: 8723d: Add set_channel

Set MAC/BB/RF register according to specified channel. The function
rtw_set_channel_mac() is used to set MAC registers, but 8723D only need
some of them.

For channel 14, we need to set different CCK DFIR values, so restore the
values when channel 1 to 13 is selected.

Spur calibration is needed in channel 13 and 14, and we do notch if spur
is over threshold.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-4-yhchuang@realtek.com

rtw88: fix spelling mistake "fimrware" -> "firmware"

There are spelling mistakes in two rtw_err error messages. Fix them.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424084733.7716-1-colin.king@canonical.com

rtw88: fix sparse warnings for download firmware routine

sparse warnings: (new ones prefixed by >>)

>> drivers/net/wireless/realtek/rtw88/mac.c:653:5: sparse: sparse:
symbol '__rtw_download_firmware' was not declared. Should it be static?
>> drivers/net/wireless/realtek/rtw88/mac.c:817:5: sparse: sparse:
symbol '__rtw_download_firmware_legacy' was not declared. Should it be
static?

Fixes: 15d2fcc6b2de ("rtw88: add legacy firmware download for 8723D devices")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424101255.28239-1-yhchuang@realtek.com

rtw88: 8723d: Organize chip TX/RX FIFO

TX FIFO size is 32k and it was divided into 256 pages with 128 bytes.
A boundary is used to split pages into two parts, head part is used to
store TX packets coming from host, and tail part is reserved for special
purposes, such as beacon packet, null data packet and so on.

The TX packets coming from host have many categories, such as VO, VI, BE,
BK, MG and etc. When going into head part of TX FIFO, they are classified
to four priority queue named low, normal, high and extra priority queues.
Each priority queue occupies predefined number of page, if a certain
priority queue is full, TX packet will store into PUB priority queue.

Similarly, RX FIFO is 16k and split into two parts, head part is used to
store RX packets, and tail part is 128 bytes and used to store report.
Thus, we fill this boundary to register as well.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-8-yhchuang@realtek.com

rtw88: 8723d: 11N chips don't support H2C queue

H2C queue is used to send command to firmware. Since 8723D doesn't support
this queue, this commit check wlan_cpu flag to avoid to set H2C related
registers.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-6-yhchuang@realtek.com

rtw88: decompose while(1) loop of power sequence polling command

The power polling command is one kind of power sequence commands. It's used
to check hardware situation, and subsequent comamnds will be executed if
hardware is ready. A special case is PCIE must toggle BIT_PFM_WOWL and try
again if first try is failed.

In order to reduce indentation to understand the code easier, move polling
part to a separate function. Then, the 'while (1)...loop' is replaced by
two statements to do first try and retry.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-5-yhchuang@realtek.com

rtw88: 8723d: Add mac power-on/-off function

The mac power-on flow consists of three steps:
1. pre_sys_cfg (Before switching power state)
2. power_switch (Switching power state)
3. init_sys_cfg (Settings after swtiching power state)

When switching power state, driver will load and parse the power sequence
tables. For 8723D devices, the logics for parsing are most same except for
the polling function. 8723D devices need to toggle BIT_PFM_WOWL twice.

The settings after power state is switched for 8723D devices are quite
different with other devices, extract a legacy function for them.

For power-off flow, 8723D devices have the same logic with existing chips.
But warning printed if we run power-off sequence in power-off state:

rtw_pci 0000:03:00.0: failed to poll offset=0x5f8 mask=0xff value=0x0

The scenario is user do 'ifconfig up' that will run power-on sequence to
bring up and then run power-off sequence to enter idle
(IEEE80211_CONF_IDLE). Then, user do 'ifconfig down' that will run
power-off sequence again, and the warning is shown. Original code check
power-on state to avoid to run power-on sequence twice, and this commit
extends to check both power-on and power-off states.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-4-yhchuang@realtek.com

rtw88: add legacy firmware download for 8723D devices

The WLAN CPU of 8723D device is different from others, add legacy
firmware download function for it. A new variable wlan_cpu is used to
decide which firmware download function we should use.

Legacy firmware file contains 32 bytes header including version and
subversion. When downloading to wlan cpu, header is excluded.

Firmware is downloaded via beacon queue to reserved page that is a part of
TX buffer. Since 11N WLAN CPU uses different control registers, this patch
introduces related control registers.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-2-yhchuang@realtek.com

rtw88: 8822[bc]: Make tables const, reduce data object size

Reduce the data size 2kb or 3kb by making tables const.
Add const to pointer declarations to make compilation work too.

(x86-64 defconfig)
$ size drivers/net/wireless/realtek/rtw88/rtw8822?.o*
text data bss dec hex filename
25054 672 8 25734 6486 drivers/net/wireless/realtek/rtw88/rtw8822b.o.new
23870 1872 8 25750 6496 drivers/net/wireless/realtek/rtw88/rtw8822b.o.old
53646 828 0 54474 d4ca drivers/net/wireless/realtek/rtw88/rtw8822c.o.new
52846 1652 0 54498 d4e2 drivers/net/wireless/realtek/rtw88/rtw8822c.o.old

(x86-64 allyesconfig)
$ size drivers/net/wireless/realtek/rtw88/rtw8822?.o*
text data bss dec hex filename
45811 6280 128 52219 cbfb drivers/net/wireless/realtek/rtw88/rtw8822b.o.new
44211 7880 128 52219 cbfb drivers/net/wireless/realtek/rtw88/rtw8822b.o.old
100195 8128 0 108323 1a723 drivers/net/wireless/realtek/rtw88/rtw8822c.o.new
98947 9376 0 108323 1a723 drivers/net/wireless/realtek/rtw88/rtw8822c.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: Use secondary channel offset enumeration

The hardware value of secondary channel offset isn't very intuitive. This
commit adds enumeration, so we can easier to check the logic with the
suffix of enumeration name, likes _UPPER or _LOWER.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: fix TX secondary channel offset of 40M if current bw is 20M or 40M

TX secondary channel offset is valid only if current bandwidth is 80M,
otherwise leave this value as zero. The wrong value of txsc40 causes
MAC unpredictable behavior.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: add interface config for 8822c

Some devices need to configure interface/HCI related reigsters
in power on flow. Add interface_cfg for HCI for the settings.

The driver only supports RTL8822BE/RTL8822CE now, and since
RTL8822BE does not need to configure PCIE, the configuration
is only added for RTL8822CE. Without it, some of the RTL8822CE
device can crash and disconnected to host in suspend/wowlan mode.

Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: avoid FW info flood

The FW info was printed everytime driver is powered on, such as
leaving IDLE state. It will flood the kernel log.

Move the FW info printing to callback when FW is loaded, so
that will only be printed once when device is probed.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: use macro to check the current band

Add macros to see which band we are, based on the current channel.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: Use rtw_write8_set to set SYS_FUNC

rtw_write8 could modify the values that we do not want
to change, use rtw_write8_set instead to only enable the
bits of sys_func_en

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: use struct rtw_fw_hdr to access firmware header

This commit doesn't change logic at all, just use struct rtw_fw_hdr to
access fixed part of 64 bytes header. Since remaining part is variable
length data of actual firmware, we don't define them within the struct.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: raise firmware version debug level

It's better to print firmware version at load time.
But since we need to set debug_mask properly to default print
rtw_dbg(), raise the debug level to rtw_info() instead.

Also change the multiple line style to one line only, it will
be easier for log analyzing.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: flush hardware tx queues

Sometimes mac80211 will ask us to flush the hardware queues.
To flush them, first we need to get the corresponding priority queues
from the RQPN mapping table.

Then we can check the available pages are equal to the originally
reserved pages, which means the hardware has returned all of the pages
it used to transmit.

Note that now we only check for 100 ms for the priority queue, but
sometimes if we have a lot of traffic (ex. 100Mbps up), some of the
packets could be dropped.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: remove redundant flag check helper function

These helper functions seems useless. And in some cases
we want to use test_and_[set/clear]_bit, these helpers
will make the code more complicated. So remove them.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: configure firmware after HCI started

After firmware has been downloaded, driver should send
some information to it through H2C commands. Those H2C
commands are transmitted through TX path.

But before HCI has been started, the TX path is not
working completely. Such as PCI interfaces, the interrupts
are not enabled, hence TX interrupts will not be issued
after H2C skb has been DMAed to the device. And the H2C
skbs will not be released until the device is powered off.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: power on again if it was already on

We could fail to power on because it was already on. If the return
value is -EALREADY, power off and then power on again to turn on the
hardware as expected.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtw88: new Realtek 802.11ac driver

This is a new mac80211 driver for Realtek 802.11ac wireless network chips.
rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode
functionalities. The firmware for both can be found at linux-firmware.

https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
For RTL8822BE: rtw88/rtw8822b_fw.bin
For RTL8822CE: rtw88/rtw8822c_fw.bin

And for now, only PCI buses (RTL8xxxE) are supported. We will add support
for USB and SDIO in the future. The bus interface abstraction can be seen
in this driver such as hci.h. Most of the hardware setting are the same
except for some TRX path or probing setup should be separated.

Supported:

* Basic STA/AP/ADHOC mode, and TDLS (STA is well tested)

Missing feature:

* WOW/PNO
* USB & SDIO bus (such as RTL8xxxU/RTL8xxxS)
* BT coexistence (8822B/8822C are combo ICs)
* Multiple interfaces (for now single STA is better supported)
* Dynamic hardware calibrations (to improve/stabilize performance)

Potential problems:

* static calibration spends too much time, and it is painful for
driver to leave IDLE state. And slows down associate process.
But reload function are under development, will be added soon!
* TRX statictics misleading, as we are not reporting status correctly,
or say, not reporting for "every" packet.

The next patch set should have BT coexistence code since RTL8822B/C are
combo ICs, and the driver for BT can be found after Linux Kernel v4.20.
So it is better to add it first to make WiFi + BT work concurrently.

Although now rtw88 is simple but we are developing more features for it.
Even we want to add support for more chips such as RTL8821C/RTL8814B.

Finally, rtw88 has many authors, listed alphabetically:

Ping-Ke Shih <pkshih@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Yan-Hsuan Chuang <yhchuang@realtek.com>

Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>