wifi: rtlwifi: rtl8821ae: Access full PMCS reg and use pci_regs.h

_rtl8821ae_clear_pci_pme_status() accesses the upper byte of the Power
Management Control/Status register (PMCS) with literal 5 offset.

Access the entire PMCS register using defines from pci_regs.h to
improve code readability.

While at it, remove the obvious comment and tweak debug prints
slightly to not sound misleading.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-9-ilpo.jarvinen@linux.intel.com

wifi: rtlwifi: rtl8821ae: Add pdev into _rtl8821ae_clear_pci_pme_status()

Add local variable pdev to shorten rtlpci->pdev.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-8-ilpo.jarvinen@linux.intel.com

wifi: rtlwifi: rtl8821ae: Use pci_find_capability()

Instead of open coding the capability structure search, find the PM
Capability using pci_find_capability().

While at it, rename the generic 'cap_pointer' to 'pm_cap' which makes
the intent of the code more obvious.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-7-ilpo.jarvinen@linux.intel.com

wifi: rtlwifi: rtl8821ae: Reverse PM Capability exists check

Check if PM Capability does not exists and return early which follows
the usual error handling pattern.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-6-ilpo.jarvinen@linux.intel.com

wifi: rtlwifi: rtl8821ae: Remove unnecessary PME_Status bit set

BIT(7) (PME_Status) is first checked and then set unnecessarily. Remove
the unnecessary setting for the bit that is already on and adjust the
comment related to it.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-5-ilpo.jarvinen@linux.intel.com

wifi: rtlwifi: cleanup few rtlxxxx_set_hw_reg() routines

Since 'u8' comparison against zero is always false, drop the
corresponding branches of AMPDU_MIN_SPACE adjustment within
'rtlxxxx_set_hw_reg()' for rtl8188ee, rtl8192ce, rtl8192de,
rtl8723ae, rtl8723be, and rtl8821ae. Compile tested only.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230925090452.25633-1-dmantipov@yandex.ru

wifi: rtlwifi: simplify LED management

Introduce 'rtl_init_sw_leds()' to replace per-chip LED
initialization code (and so drop 'struct rtl_led' as no
longer used), drop 'init_sw_leds' and 'deinit_sw_leds'
fields from 'struct rtl_hal_ops', adjust related code.

Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614061832.40882-1-dmantipov@yandex.ru

wifi: rtlwifi: rtl8821ae: don't call kfree_skb() under spin_lock_irqsave()

It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. All the SKBs have
been dequeued from the old queue, so it's safe to enqueue these
SKBs to a free queue, then free them after spin_unlock_irqrestore()
at once. Compile tested only.

Fixes: 5c99f04fec93 ("rtlwifi: rtl8723be: Update driver to match Realtek release of 06/28/14")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207141411.46098-2-yangyingliang@huawei.com

mac80211: prepare sta handling for MLO support

Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.

With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.

To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.

For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.

For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.

Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.

Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.

@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@

(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)

@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@

(
si->
- var
+ deflink.var
)

Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

rtlwifi: rtl8821ae: fix comparison to bool warning in hw.c

Fixes coccicheck warning:

drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:1897:5-13: WARNING: Comparison to bool

Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918102505.16036-5-zhengbin13@huawei.com

rtlwifi: switch from 'pci_' to 'dma_' API

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.

The only file where some GFP_ flags are updated is 'pci.c'.

When memory is allocated in '_rtl_pci_init_tx_ring()' and
'_rtl_pci_init_rx_ring()' GFP_KERNEL can be used because both functions are
called from a probe function and no spinlock is taken.

The call chain is:
rtl_pci_probe
--> rtl_pci_init
--> _rtl_pci_init_trx_ring
--> _rtl_pci_init_rx_ring
--> _rtl_pci_init_tx_ring

@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL

@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE

@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE

@@
@@
- PCI_DMA_NONE
+ DMA_NONE

@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200907193828.318233-1-christophe.jaillet@wanadoo.fr

rtlwifi: rtl8821ae: Rename RT_TRACE to rtl_dbg

Change the misleading macro name to one that is more descriptive for
rtl8821ae. Changes suggested by ckeckpatch.pl have been made.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200831184536.29950-1-Larry.Finger@lwfinger.net

rtlwifi: rtl8821ae: Remove CamelCase variables

If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.

The following checkpatch exceptions are also fixed:

WARNING: line over 80 characters
#316: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/fw.c:1751:
+ SET_8821AE_H2CCMD_AOAC_RSVDPAGE_LOC_GTK_EXT_MEM(u1rsvdpageloc2, GTKEXT_PG);

CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+ (eeaddr+1), hwinfo[eeaddr+1]);
^

CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+ (eeaddr+1), hwinfo[eeaddr+1]);
^

CHECK: spaces preferred around that '+' (ctx:VxV)
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+ if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/
^

WARNING: Comparisons should place the constant on the right side of the test
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+ if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/

CHECK: spaces preferred around that '&' (ctx:VxV)
#501: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2666:
+ pwrinfo24g->bw40_diff[rfpath][txcount] = (hwinfo[eeaddr]&0xf0) >> 4;
^
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Replace old-style license information

The traditional license information is replaced by the SPDX form. There
are no code changes.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: replace _rtl8821ae_mrate_idx_to_arfr_id with generic version

Function _rtl8821ae_mrate_idx_to_arfr_id is functionally identical to
the generic version rtl_mrate_idx_to_arfr_id, so remove
_rtl8821ae_mrate_idx_to_arfr_id and use the generic one instead.

This also fixes a missing break statement found by CoverityScan in
_rtl8821ae_mrate_idx_to_arfr_id, namely: CID#1167237 ("Missing break
in switch")

Thanks to Joe Perches for spotting this when I submitted an earlier patch.

Fixes: 3c05bedb5fef ("Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Fix connection lost problem correctly

There has been a coding error in rtl8821ae since it was first introduced,
namely that an 8-bit register was read using a 16-bit read in
_rtl8821ae_dbi_read(). This error was fixed with commit 40b368af4b75
("rtlwifi: Fix alignment issues"); however, this change led to
instability in the connection. To restore stability, this change
was reverted in commit b8b8b16352cd ("rtlwifi: rtl8821ae: Fix connection
lost problem").

Unfortunately, the unaligned access causes machine checks in ARM
architecture, and we were finally forced to find the actual cause of the
problem on x86 platforms. Following a suggestion from Pkshih
<pkshih@realtek.com>, it was found that increasing the ASPM L1
latency from 0 to 7 fixed the instability. This parameter was varied to
see if a smaller value would work; however, it appears that 7 is the
safest value. A new symbol is defined for this quantity, thus it can be
easily changed if necessary.

Fixes: b8b8b16352cd ("rtlwifi: rtl8821ae: Fix connection lost problem")
Cc: Stable <stable@vger.kernel.org> # 4.14+
Fix-suggested-by: Pkshih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: James Cameron <quozl@laptop.org> # x86_64 OLPC NL3
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Convert individual interrupt results to struct

With the RTL8822BE and later devices, the number of interrupt vectors
has grown from 2 to 4. At this point, saving and passing those vectors
in a struct makes more sense than using individual scaler variables.

In two of the drivers, code to process the second of the interrupt
registers was included, but commented out. This patch removes those
useless sections.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: drop unused ppsc->last_wakeup_time

The calculation of ppsc->last_wakeup_time is not y2038-safe, but
the variable is not used at all, so we can simply drop it.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: use ktime_get_real_seconds() for suspend time

do_gettimeofday() is deprecated and slower than necessary for the purpose
of reading the seconds. This changes rtl_op_suspend/resume to use
ktime_get_real_seconds() instead, which is simpler and avoids confusion
about whether it is y2038-safe or not.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: fix uninitialized rtlhal->last_suspend_sec time

We set rtlhal->last_suspend_sec to an uninitialized stack variable,
but unfortunately gcc never warned about this, I only found it
while working on another patch. I opened a gcc bug for this.

Presumably the value of rtlhal->last_suspend_sec is not all that
important, but it does get used, so we probably want the
patch backported to stable kernels.

Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82839
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl_pci: Extend recognized interrupt parameters from two to four ISR

8822be checks H2CQ by int_d, so we extend to four ISR.
Also, irq_mask is extended to four.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Fix typo in variable name

In _rtl8821ae_dbi_write(), wrtie_addr should be write_addr.

Signed-off-by: Nik Nyby <nikolas@gnu.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Remove unused cur_rfstate variables

Clean up unused cur_rfstate variables in rtl8188ee, rtl8723ae, rtl8723be
and rtl8821ae.

Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Add bw_update parameter for RA mask update.

- Add new parameter "is_bw_update" to control if current bandwidth setting
is updated to FW RA.
- After this commit, we keep the same setting as before.
- Later, bandwidth update in watchdog is changed to false for 8822BE.

Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8192ee: Make driver support 64bits DMA.

1. Both 32-bit and 64-bit use the same TX/RX buffer desc layout
2. Extend set_desc() and get_desc() to set and get 64-bit address
3. Remove directive DMA_IS_64BIT
4. Add module parameter to turn on 64-bit dma

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Fix connection lost problem

In commit 40b368af4b75 ("rtlwifi: Fix alignment issues"), the read
of REG_DBI_READ was changed from 16 to 8 bits. For unknown reasonsi
this change results in reduced stability for the wireless connection.
This regression was located using bisection.

Fixes: 40b368af4b75 ("rtlwifi: Fix alignment issues")
Reported-and-tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.11+
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Fix HW_VAR_NAV_UPPER operation

The cast here is wrong. We want to cast the pointer but we accidentally
do a no-op cast of the value. We normally want to set us_nav_upper to
WIFI_NAV_UPPER_US (30000) but because of this bug we instead set it to
184 on little endian systems and 0 on big endian ones.

Fixes: 3c05bedb5fef ("Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: add amplifier type for 8812ae

With correct amplifier_type, the phy praser can choose correct parameters.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

treewide: Fix typos in printk

This patch fix some spelling typos found in printk.

[jkosina@suse.cz: drop arch/arm64/kernel/hibernate.c that was already
in place]
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

rtlwifi: Add QoS-NULL and BT-QoS-NULL to reserved page.

Two additional preset responses are added to the reserved page on the
wifi device.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Move items out of rtl_pci_priv and rtl_usb_priv

In commit 6773386f977c ("rtlwifi: rtl8192c-common: Fix "BUG: KASAN:"),
a BUG detected when CONFIG_KASAN=y was fixed by reordering the layouts
of struct rtl_pci_priv, and struct rtl_usb_priv so that the variables
used by both PCI and USB drivers have the same offsets in both structs.
The better fix of relocating the critical variables into struct rtl_priv
was deferred as these changes do not have to be applied to stable
kernels.

This change also removes CamelCase variables with pLed0 => pled0.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Fix alignment issues

The addresses of Wlan NIC registers are natural alignment, but some
drivers have bugs. These are evident on platforms that need natural
alignment to access registers. This change contains the following:
1. Function _rtl8821ae_dbi_read() is used to read one byte from DBI,
thus it should use rtl_read_byte().
2. Register 0x4C7 of 8192ee is single byte.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Remove all instances of DBG_EMERG

This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Replace local debug macro RT_ASSERT

This macro can be replaced with WARN_ONCE. In addition to using a
standard debugging macro for these critical errors, we also get
a stack dump.

In rtl8821ae/hw.c, a senseless comment was removed, and an incorrect
indentation was fixed.

This patch also fixes two places in each of rtl8192ee, rtl8723be,
and rtl8821ae where the logical condition was incorrect.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Add switch variable to 'switch case not processed' messages

Help along debugging by showing what switch/case variable is not
being processed in these messages.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Convert driver to use common hardware info routine

The driver for RTL8821AE chips is converted to use the common routine
for getting the hardware information.

Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Add missing newlines to RT_TRACE calls

RT_TRACE does not add a newline to the end of a message and always
emits at KERN_DEBUG so these are susceptible to message interleaving
from other processes without the newline.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: fix error handling in *_read_adapter_info()

There are nine copies of the _rtl88ee_read_adapter_info() function,
and most but not all of them cause a build warning in some configurations:

rtl8192de/hw.c: In function '_rtl92de_read_adapter_info':
rtl8192de/hw.c:1767:12: error: 'hwinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]
rtl8723ae/hw.c: In function '_rtl8723e_read_adapter_info.constprop':
rtlwifi/rtl8723ae/hw.c:1654:12: error: 'hwinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]

The problem is that when rtlefuse->epromtype is something other than
EEPROM_BOOT_EFUSE, the rest of the function uses undefined data, resulting
in random behavior later.

Apparently, in some drivers, the problem was already found and fixed
but the fix did not make it into the others.

This picks one approach to deal with the problem and applies identical
code to all 9 files, to simplify the later consolidation of those.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

treewide: Fix typos in printk

This patch fix spelling typos found in printk
within various part of the kernel sources.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

rtlwifi: Fix size of wireless mode variable

Smatch reports the following warning:

CHECK drivers/net/wireless/realtek/rtlwifi/rc.c
drivers/net/wireless/realtek/rtlwifi/rc.c:144 _rtl_rc_rate_set_series() warn: impossible condition '(wireless_mode == 256) => (0-255 == 256)'

This warning arises because commit acc6907b87a9 ("rtlwifi: Fix warning
from ieee80211_get_tx_rates() when using 5G") now checks the wireless
mode for WIRELESS_MODE_AC_ONLY (BIT(8)) in _rtl_rc_rate_set_series().
As a result, all quantities used to store the wireless mode must be u16.

This patch also reorders struct rtl_sta_info to save a little space.

Fixes: d76d65fd2695 ("rtlwifi: fix broken VHT support")
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Convert driver to use common 5G channel table

There are several copies of the 5G channel tables in this driver. These
are removed so that the tables in the core will be used. This change
also removes a useless message of "Channel 163 in Group not found".

The number of possible 5G channels was reduced from 54 to a better
value of 49 during the conversion.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl8821ae: Fix lockups on boot

In commit 54328e64047a5 ("rtlwifi: rtl8821ae: Fix system lockups on boot"),
an attempt was made to fix a regression introduced in commit 1277fa2ab2f9
("rtlwifi: Remove the clear interrupt routine from all drivers").
Unfortunately, there were logic errors in that patch that prevented
affected boxes from booting even after that patch was applied.

The actual cause of the original problem is unknown as none of the
developers have systems that are affected.

Fixes: 54328e64047a ("rtlwifi: rtl8821ae: Fix system lockups on boot")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V4.1+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: rtl818x: Move drivers into new realtek directory

Now that a new mac80211-based driver for Realtek devices has been submitted,
it is time to reorganize the directories. Rather than having directories
rtlwifi and rtl818x be in drivers/net/wireless/, they will now be in
drivers/net/wireless/realtek/. This change simplifies the directory
structure, but does not result in any configuration changes that are
visable to the user.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>