#
46190882 |
|
11-Oct-2023 |
Dmitry Antipov <dmantipov@yandex.ru> |
wifi: rtlwifi: simplify TX command fill callbacks Since 'rtlpriv->cfg->ops->fill_tx_cmddesc()' is always called with 'firstseg' and 'lastseg' set to 1 (and the latter is never actually used), all of the relevant chip-specific routines may be simplified. Compile tested only. Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Acked-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20231011154442.52457-2-dmantipov@yandex.ru
|
#
773755d9 |
|
08-Sep-2019 |
Larry Finger <Larry.Finger@lwfinger.net> |
rtlwifi: rtl8723ae: Convert inline routines to little-endian words In this step, the read/write routines for the descriptors are converted to use __le32 quantities, thus a lot of casts can be removed. Callback routines still use the 8-bit arrays, but these are changed within the specified routine. The macro that cleared a descriptor has now been converted into an inline routine. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
#
a9db071f |
|
08-Sep-2019 |
Larry Finger <Larry.Finger@lwfinger.net> |
rtlwifi: rtl8723ae: Convert macros that set descriptor As a first step in the conversion, the macros that set the RX and TX descriptors are converted to static inline routines, and the names are changed from upper to lower case. To minimize the changes in a given step, the input descriptor information is left as as a byte array (u8 *), even though it should be a little-endian word array (__le32 *). That will be changed in the next patch. Several places where checkpatch.pl reports lines too long are fixed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
#
05e2a0cb |
|
08-Sep-2019 |
Larry Finger <Larry.Finger@lwfinger.net> |
rtlwifi: rtl8723ae: Replace local bit manipulation macros This driver uses a set of local macros to manipulate the RX and TX descriptors, which are all little-endian quantities. These macros are replaced by the bitfield macros le32p_replace_bits() and le32_get_bits(). In several places, the macros operated on an entire 32-bit word. In these cases, a direct read or replacement is used. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
#
eb4b2d33 |
|
08-Sep-2019 |
Larry Finger <Larry.Finger@lwfinger.net> |
rtlwifi: rtl8723ae: Remove unused GET_XXX and SET_XXX macros As the first step in converting from macros that get/set information in the RX and TX descriptors, unused macros are being removed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
#
48fa0b4d |
|
14-Feb-2019 |
Larry Finger <Larry.Finger@lwfinger.net> |
rtlwifi: rtl8723ae: Replace old-style license information The traditional license information is replaced by the SPDX form. There are no code changes. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
#
ff77960d |
|
18-May-2018 |
Ping-Ke Shih <pkshih@realtek.com> |
rtlwifi: remove dummy hal_op rx_command_packet from rtl8188ee and rtl8723ae The caller of hal_op rx_command_packet will assert function pointer before calling, so we can remove dummy functions safely. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
#
0c07bd74 |
|
29-Sep-2017 |
Ping-Ke Shih <pkshih@realtek.com> |
rtlwifi: rtl8192ee: Make driver support 64bits DMA. 1. Both 32-bit and 64-bit use the same TX/RX buffer desc layout 2. Extend set_desc() and get_desc() to set and get 64-bit address 3. Remove directive DMA_IS_64BIT 4. Add module parameter to turn on 64-bit dma Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Yan-Hsuan Chuang <yhchuang@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
#
08aba42f |
|
15-Jun-2016 |
Arnd Bergmann <arnd@arndb.de> |
rtlwifi: use s8 instead of char Compiling the rtlwifi drivers for ARM with gcc -Wextra warns about lots of incorrect code that results from 'char' being unsigned here, e.g. realtek/rtlwifi/rc.c:113:18: error: comparison is always true due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8188ee/dm.c:1070:22: error: comparison is always false due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8192ce/trx.c:54:16: error: comparison is always false due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8192cu/mac.c:601:16: error: comparison is always false due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8192de/trx.c:53:16: error: comparison is always false due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8192ee/phy.c:1268:12: error: comparison is always true due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8192se/rf.c:150:20: error: comparison is always false due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8723be/dm.c:877:29: error: comparison is always false due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8723be/phy.c:386:16: error: comparison is always true due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8821ae/dm.c:1514:38: error: comparison is always false due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8821ae/phy.c:1558:11: error: comparison is always false due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8821ae/phy.c:386:24: error: comparison is always false due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/rtl8821ae/trx.c:55:12: error: comparison is always false due to limited range of data type [-Werror=type-limits] realtek/rtlwifi/stats.c:31:16: error: comparison is always false due to limited range of data type [-Werror=type-limits] This patch changes all uses of 'char' in this driver that refer to 8-bit integers to use 's8' instead, which is signed on all architectures. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
#
ce254243 |
|
22-Feb-2016 |
Colin Ian King <colin.king@canonical.com> |
rtlwifi: pass struct rtl_stats by reference as it is more efficient passing rtl_stats by value is inefficient; the structure is over 300 bytes in size and generally just one field (packet_report_type) is being accessed, so the pass by value is a relatively large overhead. This change just affects just the rx_command_packet calls. Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
#
f1d2b4d3 |
|
07-Sep-2015 |
Larry Finger <Larry.Finger@lwfinger.net> |
rtlwifi: rtl818x: Move drivers into new realtek directory Now that a new mac80211-based driver for Realtek devices has been submitted, it is time to reorganize the directories. Rather than having directories rtlwifi and rtl818x be in drivers/net/wireless/, they will now be in drivers/net/wireless/realtek/. This change simplifies the directory structure, but does not result in any configuration changes that are visable to the user. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|