wifi: brcmfmac: feature: Add support for setting feats based on WLC version

The "wlc_ver" iovar returns information on the WLC and EPI versions.
This can be used to determine whether the PMKID_V2 and _V3 features are
supported.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230214092423.15175-4-marcan@marcan.st

wifi: brcmfmac: cfg80211: Add support for scan params v2

This new API version is required for at least the BCM4387 firmware. Add
support for it, with a fallback to the v1 API.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230214092423.15175-3-marcan@marcan.st

brcmfmac: Add dump_survey cfg80211 ops for HostApd AutoChannelSelection

To enable ACS feature in Hostap daemon, dump_survey cfg80211 ops and dump
obss survey command in firmware side are needed. This patch is for adding
dump_survey feature and adding DUMP_OBSS feature flag to check if
firmware supports dump_obss iovar.

Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Ian Lin <ian.lin@infineon.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220929012527.4152-2-ian.lin@infineon.com

brcmfmac: support 4-way handshake offloading for WPA/WPA2-PSK in AP mode

Firmware may have authenticator code built-in. This is detected by the
driver and indicated in the wiphy features flags. User space can use
this flag to determine whether or not to provide the pre-shared key
material in the nl80211 start AP command to offload the 4-way handshake
in AP mode.

Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817073316.33402-3-stanley.hsu@cypress.com

brcmfmac: add initial support for monitor mode

Report monitor interface availability using cfg80211 and support it in
the add_virtual_intf() and del_virtual_intf() callbacks. This new
feature is conditional and depends on firmware flagging monitor packets.
Receiving monitor frames is already handled by the brcmf_netif_mon_rx().

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: add support for SAE authentication offload

The firmware may have SAE authentication code built-in. This is
detected by the driver and indicated in the wiphy features flags.
User-space can use this flag to determine whether or not to provide
the password material for SAE authentication in the nl80211 CONNECT
command.

Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: enable DFS_OFFLOAD extended feature if supported

If the firmware supports 802.11h and the device can operate in 5GHz
band we can enable DFS_OFFLOAD extended feature.

Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: switch source files to using SPDX license identifier

With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.

Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: support monitor frames with the hardware/ucode header

So far there were two monitor frame formats:
1) 802.11 frames (with frame (sub)type & all addresses)
2) 802.11 frames with the radiotap header

Testing the latest FullMAC firmwares for 4366b1/4366c0 resulted in
discovering a new format being used. It seems (almost?) identical to the
one known from ucode used in SoftMAC devices which is most likely the
same codebase anyway.

While new firmwares will /announce/ radiotap header support using the
"rtap" fw capability string it seems no string was added for the new
ucode header format.

All above means that:
1) We need new format support when dealing with a received frame
2) A new feature bit & mapping quirks have to be added manually

As for now only an empty radiotap is being created. Adding support for
extracting some info (band, channel, signal, etc.) is planned for the
future.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: detect firmware support for radiotap monitor frames

Depending on used build-time options some firmwares may already include
radiotap header in passed monitor frames. Add a new feature flag to
store info about it. It's needed for proper handling of received frames
before passing them up.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: detect firmware support for monitor interface

Many/most of firmwares support creating monitor interface but only the
most recent ones explicitly /announce/ it using a "monitor" entry in the
list of capabilities.

Check for that entry and store internally info about monitor mode
support using a new feature flag. Once we sort out all details of
handling monitor interface it will be used when reporting available
interfaces to the cfg80211.

Later some fallback detecion method may be added for older firmwares.
For now just stick to the "monitor" capability which should be 100%
reliable.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: use wiphy debugfs dir entry

The driver used to create a brcmfmac dir entry at the top level
debugfs mount point. This moves the debugfs entries into the
wiphy debugfs dir entry.

Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: support 4-way handshake offloading for WPA/WPA2-PSK

The firmware may have supplicant code built-in. This is detected
by the driver and indicated in the wiphy features flags. User-space
can use this flag to determine whether or not to provide the
pre-shared key material in the nl80211 CONNECT command.

Reviewed-by: Gautam (Gautam Kumar) Shukla <gautams@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: add firmware feature detection for gscan feature

Detect gscan support in firmware by doing pfn_gscan_cfg iovar with
invalid version.

Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: add 802.11w management frame protection support

Add full support for both AP and STA for management frame protection.

Reviewed-by: Arend Van Spriel <arend.van@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: keep ARP and ND offload enabled during WOWL

Currently ARP and ND (IPv6 Neigbor Discovery) offload get disabled
on entering suspend. However when firmwares support the wowl_cap
iovar then these offload routines can be kept enabled as they
will work during WOWL as well.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: add wowl gtk rekeying offload support

This patch adds support for gtk rekeying offload and for gtk
rekeying failure during wowl mode.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Add support for scheduled scan mac randomization

Scheduled scan be requested to use mac randomization. This patch
checks the flags and enables the randomization if desired.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Make TDLS a detectable feature

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Add RSDB support.

Broadcom devices with a single 802.11 core can work on two band
concurrently using VSDB feature, ie. Virtual Simultaneous Dual-Band.
For devices that are fitted with two 802.11 cores and RF paths the
driver should support a firmware feature called RSDB, which stands
for Real Simultaneous Dual-Band. RSDB works almost autonomously in
firmware except for AP config. When the device supports RSDB then
the interface should not be brought down when configuring it,
otherwise the link (if configured) on the other interface will be
lost.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[kvalo@codeaurora.org: changed the commit log based on discussion]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcm80211: move under broadcom vendor directory

Part of reorganising wireless drivers directory and Kconfig. Note that I had to
edit Makefiles from subdirectories to use the new location.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>