wifi: ath12k: enable 802.11 power save mode in station mode

To reduce power consumption enable 802.11 power save mode in
station mode. This allows both radio and CPU to sleep more.

Only enable the mode on WCN7850, other chips don't support it
for now.

To test that power save mode is running, run below command and
check there is no NULL Data frame seen by a sniffer:
iw dev <inf> set power_save off

And run below command, then check there is a NULL Data frame
in sniffer:
iw dev <inf> set power_save on

Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4

Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240201035830.2534-1-quic_bqiang@quicinc.com

wifi: ath12k: disable QMI PHY capability learn in split-phy QCN9274

QMI PHY capability learn is used to get PHY count information to
support single/multi link operation (SLO/MLO) configuration. The
QCN9274 dualmac firmware currently do not support SLO/MLO, if two
PHYs are within the same chip. Due to this firmware crashes in
split-phy QCN9274, while bringing up AP with MLO parameter enabled
in QMI host capability request message.

The QMI PHY capability learn is not required for split-phy QCN9274,
if SLO/MLO is not supported within the same chip. Hence, disable QMI
PHY capability learn support in split-phy QCN9274.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-14-quic_rajkbhag@quicinc.com

wifi: ath12k: Read board id to support split-PHY QCN9274

QCN9274 can support single-PHY or split-PHY architecture. Currently,
only the single-PHY architecture is supported in ath12k.

The split-PHY QCN9274 requires different AMSS firmware binary
"amss_dualmac.bin".

Hence, add support to read board id from OTP. Based on board id
decide whether single-mac / dual-mac firmware needs to be downloaded
to the target. Also, update HW param max_radios to support split-PHY
in QCN9274.

Also, add new Firmware IE for firmware_N.bin
"ATH11K_FW_IE_AMSS_DUALMAC_IMAGE" to support dualmac QCN9274.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

Signed-off-by: Ganesh Babu Jothiram <quic_gjothira@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-13-quic_rajkbhag@quicinc.com

wifi: ath12k: split hal_ops to support RX TLVs word mask compaction

With word mask subscription support, the rx_desc structure will
change. The fields in this structure rx_desc will be reduced to only
the required fields. To make word mask subscription changes compatible
with the older firmware version (firmware that does not support word
mask subscription), two different structures of rx_desc will be
required for the same hardware.

Most of the hal_ops are directly related to rx_desc.

Hence, split hal_ops into operations that are independent of rx_desc
(hal_ops) and the operations that are directly dependent on rx_desc
(hal_rx_ops). These hal_rx_ops depend on both hardware and firmware
hence move them out of hw_params.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-8-quic_rajkbhag@quicinc.com

wifi: ath12k: fix firmware assert during insmod in memory segment mode

In segment memory mode, firmware allocates memory segments of size
2 MB. This 2 MB memory is used by firmware for the number of peers.
This number of peer is sent from host to firmware during WMI init
command. For single-phy the number of peers sent is
TARGET_NUM_PEERS_SINGLE = 529 (512 + 17). While for split-phy number
of peers sent to firmware is TARGET_NUM_PEERS_DBS = 2 *(512 + 17) =
1058. With this 1058 number of peers firmware is unable to allocate
memory in 2 MB segment and firmware crash is observed.

Hence, fix this firmware crash by reducing the number of stations
TARGET_NUM_STATIONS for split-phy.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-7-quic_rajkbhag@quicinc.com

wifi: ath12k: add firmware-2.bin support

Firmware IE containers can dynamically provide various information
what firmware supports. Also it can embed more than one image so
updating firmware is easy, user just needs to update one file in
/lib/firmware/.

The firmware API 2 or higher will use the IE container format, the
current API 1 will not use the new format but it still is supported
for some time. Firmware API 2 files are named as firmware-2.bin
(which contains both amss.bin and m3.bin images) and API 1 files are
amss.bin and m3.bin.

Currently ath12k PCI driver provides firmware binary (amss.bin) path to
MHI driver, MHI driver reads firmware from filesystem and boots it. Add
provision to read firmware files from ath12k driver and provide the amss.bin
firmware data and size to MHI using a pointer.

Currently enum ath12k_fw_features is empty, the patches adding features will
add the flags.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123122812.3811251-1-quic_rajkbhag@quicinc.com

wifi: ath12k: Fix issues in channel list update

Currently, the logic used to select the 6 GHz band is incorrect,
which may cause 6 GHz supported channels to not be updated properly.
This is because the 6 GHz Max frequency supported by the driver is
being compared to the Max frequency supported on the board. If in
some cases, the 6 GHz Max frequency supported on the board is less
than the defined 6 GHz Max frequency, all 6 GHz channels are disabled.
To address this, compare the max frequency supported by the board to
the defined 6 GHz Minimum frequency by the driver.

Similarly, when a dual mac card supports both 6 GHz and 5 GHz radios,
if the 5 GHz radio gets enumerated first before 6 GHz, the checks in
ath12k_mac_setup_channels_rates() can cause the 5 GHz channels which
were enabled earlier to get disabled when the 6 GHz channel list is
updated. This is because the Min 6 GHz frequency defined in the driver
is 5945 MHz, which should be 5925 MHz since channel 2 is not considered
currently, but the firmware can pass 5925 MHz as the minimum.
Hence, update the Min frequency supported by the driver to 5925 MHz.

In addition, ensure that the channel list update to firmware updates
only the channels that the current radio (ar) supports rather than
considering the wiphy support. This would be required when multiple pdevs
are supported in a wiphy and they support different ranges of frequencies
or bands as in single wiphy support.

Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240117062628.8260-1-quic_srirrama@quicinc.com

wifi: ath12k: Introduce the container for mac80211 hw

To support multi link operation, we need to combine all the link/pdev
under a single wiphy. This avoids the overhead of synchronization
across multiple hardware instances in both the cfg80211 and mac80211
layers. Currently, each link/pdev is registered as separate wiphy,
tightly coupled with link/pdev/radio (ar) structure. To enable single
wiphy registration within the chip, we decouple the wiphy data entity from
the link/pdev/radio (ar) structure and move it under the chip (ab)
structure with a new data container (ath12k_hw) structure. This approach
improves scalability for future multi link operation support.

mac80211 hw private data structure diagram
------------------------------------------

Now After

+---------------------+ +---------------------+
|mac80211 hw priv data| |mac80211 hw priv data|
| | | |
| | | |
| | | |
| | | ath12k_hw (ah) |
| | | |
| | +-------------------> | |
| ath12k (ar) | | +-------------+ |
| | | | | |
| | | | ath12k (ar) | |
| | | | | |
| | | | | |
| | | +-------------+ |
| | | |
| | | |
+---------------------+ +---------------------+

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240118010320.3918136-3-quic_periyasa@quicinc.com

wifi: ath12k: Refactor the mac80211 hw access from link/radio

Currently, mac80211 hardware accesses link/radio structure directly in
multiple locations. Introduce helper function to avoid this direct
access, as this change will facilitate refactoring for Multi-link
operation support.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240118010320.3918136-2-quic_periyasa@quicinc.com

wifi: ath12k: add support to search regdb data in board-2.bin for WCN7850

Currently ath12k only downloads the same regdb.bin file for all WCN7850
chips, actually ath12k needs to distinguish all different WCN7850 chips.

This is to re-use the string type which includes bus, chip id, board id,
vendor, device, subsystem-vendor, subsystem-device and variant for
WCN7850 to distinguish different regdb in board-2.bin.

ath12k will first load board-2.bin and search in it for the regdb data
with the above parameters. If matched with one regdb data, download it
to firmware. And if not, download regdb.bin instead.

Add enum value ATH12K_BD_IE_REGDB and enum type ath12k_bd_ie_regdb_type
to distinguish regdb data and board data since they are in the same file
board-2.bin.

Test log:
[ 3833.091948] ath12k_pci 0000:05:00.0: boot using board name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[ 3833.092072] ath12k_pci 0000:05:00.0: boot firmware request ath12k/WCN7850/hw2.0/board-2.bin size 205316
[ 3833.092079] ath12k_pci 0000:05:00.0: board name
[ 3833.092083] ath12k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092088] ath12k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 31 -id=1
[ 3833.092091] ath12k_pci 0000:05:00.0: board name
[ 3833.092095] ath12k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092099] ath12k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 32 -id=2
[ 3833.092102] ath12k_pci 0000:05:00.0: board name
[ 3833.092105] ath12k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092109] ath12k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 33 -id=3
[ 3833.092112] ath12k_pci 0000:05:00.0: board name
[ 3833.092116] ath12k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 3833.092119] ath12k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c 7cb,device=1103,
[ 3833.092123] ath12k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 3833.092126] ath12k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d =17cb,subsystem-
[ 3833.092130] ath12k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d device=3374,qmi-
[ 3833.092133] ath12k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f chip-id=2,qmi-bo
[ 3833.092137] ath12k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 36 2c 76 61 72 69 61 ard-id=266,varia
[ 3833.092140] ath12k_pci 0000:05:00.0: 00000070: 6e 74 3d 48 50 5f 47 38 5f 4c 61 6e 63 69 61 31 nt=HP_G8_Lancia1
[ 3833.092144] ath12k_pci 0000:05:00.0: 00000080: 35 5
[ 3833.092147] ath12k_pci 0000:05:00.0: board name
[ 3833.092150] ath12k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 3833.092154] ath12k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c 7cb,device=1103,
[ 3833.092157] ath12k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 3833.092161] ath12k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d =17cb,subsystem-
[ 3833.092165] ath12k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d device=3374,qmi-
[ 3833.092168] ath12k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f chip-id=2,qmi-bo
[ 3833.092172] ath12k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 36 ard-id=266
[ 3833.092206] ath12k_pci 0000:05:00.0: board name
[ 3833.092209] ath12k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 3833.092213] ath12k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c 7cb,device=1103,
[ 3833.092216] ath12k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 3833.092220] ath12k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d =17cb,subsystem-
[ 3833.092223] ath12k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d device=3374,qmi-
[ 3833.092227] ath12k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f chip-id=2,qmi-bo
[ 3833.092230] ath12k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 32 ard-id=262
[ 3833.092234] ath12k_pci 0000:05:00.0: boot found match regdb data for name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[ 3833.092238] ath12k_pci 0000:05:00.0: board name
[ 3833.092241] ath12k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092245] ath12k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 31 31 -id=11
[ 3833.092248] ath12k_pci 0000:05:00.0: board name
[ 3833.092251] ath12k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092255] ath12k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 32 32 -id=22
[ 3833.092258] ath12k_pci 0000:05:00.0: board name
[ 3833.092261] ath12k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092265] ath12k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 33 33 -id=33
[ 3833.092268] ath12k_pci 0000:05:00.0: boot found regdb data for 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[ 3833.092272] ath12k_pci 0000:05:00.0: fetched regdb

Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231216060140.30611-5-quic_bqiang@quicinc.com

wifi: ath12k: add string type to search board data in board-2.bin for WCN7850

Currently ath12k only supports string type with bus, chip id and board id
such as "bus=ahb,qmi-chip-id=1,qmi-board-id=4" for AHB bus chip and
"bus=pci,qmi-chip-id=0,qmi-board-id=255" for PCI bus chip in board-2.bin.
For WCN7850, it is not enough to distinguish all different chips.

Add a new string type which includes bus, chip id, board id, vendor,
device, subsystem-vendor and subsystem-device for WCN7850.

ath12k will first load board-2.bin and searches in it for the board data
with the above parameters. If matched with one board data, ath12k downloads
it to firmware. And if not, downloads board.bin instead.

Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231216060140.30611-2-quic_bqiang@quicinc.com

wifi: ath12k: add CE and ext IRQ flag to indicate irq_handler

Add two flags to indicate whether IRQ handler for CE and DP can be called.
This is because in one MSI vector case, interrupt is not disabled in
hif_stop and hif_irq_disable. So if interrupt is disabled, MHI interrupt
is disabled too.

Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4

Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231121021304.12966-3-quic_kangyang@quicinc.com

wifi: ath12k: Remove struct ath12k::ops

Currently struct ath12k defines the following member:
struct ieee80211_ops *ops;

This is being flagged by checkpatch.pl:
WARNING: struct ieee80211_ops should normally be const

The original plan was to add the const qualifier. However, it turns
out this is actually unused, so remove it.

No functional changes, compile tested only.

Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231106-ath12k-remove-ieee80211_ops-v1-2-d72cef1a855b@quicinc.com

wifi: ath12k: Introduce and use ath12k_sta_to_arsta()

Currently, the logic to return an ath12k_sta pointer, given a
ieee80211_sta pointer, uses typecasting throughout the driver. In
general, conversion functions are preferable to typecasting since
using a conversion function allows the compiler to validate the types
of both the input and output parameters.

ath12k already defines a conversion function ath12k_vif_to_arvif() for
a similar conversion. So introduce ath12k_sta_to_arsta() for this use
case, and convert all of the existing typecasting to use this
function.

Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019-upstream-ath12k_sta_to_arsta-v1-1-06f06f693338@quicinc.com

wifi: ath12k: Remove ath12k_base::bd_api

Currently struct ath12k_base defines the member bd_api. However, this
member is only accessed within ath12k_core_fetch_bdf(). Since the
scope is local just to that one function, remove it from ath12k_base
and instead just use a local stack variable.

No functional changes, compile tested only.

Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231013-ath11k_bd_api-v1-2-3fefe4629706@quicinc.com

wifi: ath12k: add read variant from SMBIOS for download board data

This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.

Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230905105637.10230-1-quic_wgong@quicinc.com

wifi: ath12k: add support for hardware rfkill for WCN7850

When hardware rfkill is enabled in the firmware, it will report the
capability using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event
to the host. Currently ath12k does not process this service capability. In
order to support this, update ath12k to check if the capability is enabled,
if so, send the GPIO information to firmware. When the firmware detects
hardware rfkill is enabled by the user, it will report it using
WMI_RFKILL_STATE_CHANGE_EVENTID. When ath12k receive the event, it will set
the value of rfkill_radio_on based on whether radio_state is equal to
WMI_RFKILL_RADIO_STATE_ON, then send WMI_PDEV_PARAM_RFKILL_ENABLE to
firmware.

Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4

Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906110412.182176-1-quic_lingbok@quicinc.com

wifi: ath12k: Remove unused declarations

Commit d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
declared but never implemented these, remove it.

Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230816130550.50896-1-yuehaibing@huawei.com

wifi: ath12k: configure puncturing bitmap

Enable the feature flag to indicate the driver support for
preamble puncturing. Firmware will support this feature
by default from IEEE 802.11be onwards.
Configure the bitmap as part of VDEV start/restart and
peer association commands.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-12-quic_alokad@quicinc.com

wifi: ath12k: WMI support to process EHT capabilities

Add WMI support to process the EHT capabilities passed by
the firmware. Add required EHT specific definitions in
structures ath12k_band_cap and ath12k_wmi_svc_rdy_ext_parse.

For single_pdev chip such as WCN7850, only one pdev is created
and only one hardware is registered to mac80211. This one pdev
manages both 2.4 GHz radio and 5 GHz/6 GHz radio.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-4-quic_alokad@quicinc.com

wifi: ath12k: add wait operation for tx management packets for flush from mac80211

Transmission of management packets are done in a work queue. Sometimes
the workqueue does not finish Tx immediately, then it lead after the next
step of vdev delete finished, it start to send the management packet to
firmware and lead firmware crash.

ieee80211_set_disassoc() have logic of ieee80211_flush_queues() after
it send_deauth_disassoc() to ath12k, its purpose is make sure the
deauth was actually sent, so it need to change ath12k to match the
purpose of mac80211.

To address these issues wait for Tx management as well as Tx data packets.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthik M <quic_karm@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230419095738.19859-1-quic_rgnanase@quicinc.com

wifi: ath12k: fix firmware assert during channel switch for peer sta

Currently, during change in bandwidth for peer sta, host sends the
new value of channel width via WMI_PEER_CHWIDTH set peer param command
alone. This can lead to firmware assert in some scenario since before
the command, firmware was having value of channel width and its
corresponding phymode. After the command, host tries to set the new
value of channel width alone which can become incompatible when compared
with its phymode.

For example:

Bandwidth Upgrade
~~~~~~~~~~~~~~~~~~
After association, sta is in 40 MHz bandwidth in 11ax-HE40 phymode.
After bandwidth upgrades, sta moves to 80 MHz but as per phymode,
max bandwidth is still 40 MHz. Hence, firmware assert is seen.
So in this case first phymode should be moved to 11ax-HE80
followed by bandwidth change.

Bandwidth Downgrade
~~~~~~~~~~~~~~~~~~
Similarly, reverse of above is also possible when sta is in 40 MHz
bandwidth in 11ax-HE40 phymode. Bandwidth should be changed to 20 MHz
and if host sends phymode first then, phymode will become 11ax-HE20
and will be incompatible with bandwidth value and hence firmware
assert will be seen. Hence, in this case first channel width
should be set followed by phymode.

Fix this issue by sending WMI set peer param command for phymode as
well as bandwidth based on the type of bandwidth change i.e upgrade
or downgrade.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230315113202.8774-1-quic_aarasahu@quicinc.com

wifi: ath12k: Fix spelling mistakes in warning messages and comments

There are quite a few spelling mistakes in warning messages and a lot
of the comments. Fix these.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230214092122.265336-1-colin.i.king@gmail.com

wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices

ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.

ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.

ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.

Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.

The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.

The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:

https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52

The driver has had multiple authors who are listed in alphabetical
order below.

Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>