wifi: ath11k: Update Qualcomm Innovation Center, Inc. copyrights

Update the copyright for all ath11k files modified on behalf of
Qualcomm Innovation Center, Inc. in 2021 through 2023.

Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231128-ath12kcopyrights-v1-2-be0b7408cbac@quicinc.com

wifi: ath11k: Ignore frags from uninitialized peer in dp.

When max virtual ap interfaces are configured in all the bands with
ACS and hostapd restart is done every 60s, a crash is observed at
random times.
In this certain scenario, a fragmented packet is received for
self peer, for which rx_tid and rx_frags are not initialized in
datapath. While handling this fragment, crash is observed as the
rx_frag list is uninitialised and when we walk in
ath11k_dp_rx_h_sort_frags, skb null leads to exception.

To address this, before processing received fragments we check
dp_setup_done flag is set to ensure that peer has completed its
dp peer setup for fragment queue, else ignore processing the
fragments.

Call trace:
ath11k_dp_process_rx_err+0x550/0x1084 [ath11k]
ath11k_dp_service_srng+0x70/0x370 [ath11k]
0xffffffc009693a04
__napi_poll+0x30/0xa4
net_rx_action+0x118/0x270
__do_softirq+0x10c/0x244
irq_exit+0x64/0xb4
__handle_domain_irq+0x88/0xac
gic_handle_irq+0x74/0xbc
el1_irq+0xf0/0x1c0
arch_cpu_idle+0x10/0x18
do_idle+0x104/0x248
cpu_startup_entry+0x20/0x64
rest_init+0xd0/0xdc
arch_call_rest_init+0xc/0x14
start_kernel+0x480/0x4b8
Code: f9400281 f94066a2 91405021 b94a0023 (f9406401)

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403184155.8670-2-quic_nmaran@quicinc.com

ath11k: Add peer rhash table support

When more clients (128) are connected, the UL data traffic
KPI measurement is low compared to single client. This issue
is due to more CPU cycles spent on the peer lookup operation
with more clients. So reduce the peer lookup operation by
modifying the linear based lookup operation into the rhash
based lookup operation. This improve the peak throughput
measurement. Since this is a software algorithm change, it is
applicable for all the platforms.

TCP UL 128 Clients test case Observation (64bit system):
Previous: ~550 Mbps
Now : ~860 Mbps

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644036628-5334-1-git-send-email-quic_periyasa@quicinc.com

ath11k: fix fw crash due to peer get authorized before key install

Firmware expects host to authorize the peer after the successful key
install. But host authorize the peer before the key install, this trigger
the firmware assert which leads to Q6 crash. To avoid this Q6 crash, host
should authorize the peer after the key install. So introduce is_authorized
in peer object to identify that peer is authorize or not. When
IEEE80211_STA_CONTROL_PORT flag is unset, peer move to authorize state
before the vdev up. When the same flag is set then peer move to authorize
state after vdev up. So added authorise check in ath11k_bss_assoc() to
handle the earlier state transition case. Also added the WMI authorize
procedure in ath11k_mac_op_sta_state() to handle the non-earlier state
transition case.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636554200-12345-1-git-send-email-quic_periyasa@quicinc.com

ath11k: Update tx descriptor search index properly

Tx descriptor search index field should be updated with hw peer id
and not by AST Hash as per the HW/FW recommendation. Incorrect search
index causes throughput degradation in all scenario for all the
platforms. so updated the search index field with hw peer id, which
is a common change applicable for all the platforms. Also no need of these
configuration for non station type. seen 10% throughput increase in WDS
traffic with this change.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612410960-9120-1-git-send-email-periyasa@codeaurora.org

ath11k: start vdev if a bss peer is already created

For QCA6390, bss peer must be created before vdev is to start. This
change is to start vdev if a bss peer is created. Otherwise, ath11k
delays to start vdev.

This fixes an issue in a case where HT/VHT/HE settings change between
authentication and association, e.g., due to the user space request
to disable HT.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201211051358.9191-1-cjhuang@codeaurora.org

ath11k: peer delete synchronization with firmware

Peer creation in firmware fails, if last peer deletion
is still in progress.
Hence, add wait for the event after deleting every peer
from host driver to synchronize with firmware.

Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-3-git-send-email-mkenna@codeaurora.org

ath11k: fix duplication peer create on same radio

Add the pdev index information in the peer object to validate
the peer creation. Ignore the peer creation request, if the given
MAC address is already present in the peer list with same radio.
If we allow the peer creation in above scenario, FW assert will happen.
Above scenario occurred in two cases, where Multiple AP VAP created in
the same radio.

1. when testing tool sends association request to two AP with same
MAC address
2. when a station do roaming from one AP VAP to another AP VAP.

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586343795-21422-1-git-send-email-periyasa@codeaurora.org

ath11k: Perform per-msdu rx processing

As Hash based reo destination selection is configured,
the decapped packets reach different reo destintion rings
based on the destintaion ring selected for the computed hash (based on
the 5-tuple {ip src/ip dst/src port/dst port/protocol}) by hw and
as configured by driver.

Hence the current implementation of amsdu list based processing after all
the subframes of amsdu are received (since all msdu's for a pdev are
received in same reo dest ring), is not applicable here and hence is
replaced with per msdu based handling as these subframes
can be received in different reo dest rings.

Also, as some of the rx descriptor fields might be valid only for the
first msdu (for ex. received 80211 header, encryption type, etc),
it might not be useful now as we cannot sync between different
subframes received in different rings. Hence do not rely on those
fields and replace them with fieds valid only on per msdu descriptors.
Also cache other details such as encryption type for a peer so that
it can be reused when a packet is received from it.

Co-developed-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath11k: handle RX fragments

IPQ8074 HW has support to verify the PN of the received frames.
For all frames except for fragmented ones, HW checks the PN and
delivers them to the driver. For fragmented frames, driver is
required to do a little more; it has to reassemble the fragments
and then reinject them to the HW for verifying the PN. Currently,
to keep the logic simple, PN verifcation is disabled in HW and is
handled in mac80211 for all the frames (fragmented and unfragmented).

On the contrary, offloading PN Validation to the HW brings important
benefits. It reduces CPU cycles spent on the host CPU for verifying
the same; helps in enabling features which improve performance like
mac80211 fast RX path, enabling multiple REO rings for parallel RX
processing, 802.11 decapsulation offloading. All these features are
dependent on PN offload which in turn is dependent on handling of
the received fragments in the driver.

When TKIP security is used, additional handling is required while
processing the fragments; since MIC is computed on an MSDU in TKIP,
only the last fragment has the MIC info. In this case, driver has to
compute the MIC after reassembly and compare it against the MIC
present in the frame. For this, MICHAEL_MIC kernel crypto library
APIs are used and the dependencies are appropriately set.

Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath11k: driver for Qualcomm IEEE 802.11ax devices

ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first
supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k
uses mac80211 and supports AP, Station and Mesh modes.

Even though ath11k has some similar code as with ath10k (especially
the WMI layer) it was concluded to be simpler to have a "clean start"
for ath11k code base and not try to share the code with ath10k. This
makes maintenance easier and avoids major changes in ath10k, which
would have significantly increased the risk of regressions in existing
setups.

Even though the driver is very similar with ath10k but there are major
differences as well. The datapath is completely different. ath11k
supports multiple MACs, called "soc" in the firmware interface. And
there's only one WMI interface to support.

Currently ath11k supports only IEEE 802.11ac mode, but patches for
802.11ax are available and they will be submitted after ath11k is
accepted to upstream.

The firmware images are available from ath11k-firmware repository but
they will be also submitted to linux-firmware:

https://github.com/kvalo/ath11k-firmware

This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1.

The driver has had multiple authors who are listed in alphabetical
order below.

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>