wifi: ath11k: fix IOMMU errors on buffer rings

virt_to_phys() doesn't work on systems with IOMMU enabled, which have
non-identity physical-to-IOVA mappings. It leads to IO_PAGE_FAULTs like this:

[IO_PAGE_FAULT domain=0x0023 address=0x1cce00000 flags=0x0020]

And no association to the AP can be established.

This patch changes that to dma_map_single(), which works correctly. Even
virt_to_phys() documentation says device drivers should not use it:

This function does not give bus mappings for DMA transfers. In
almost all conceivable cases a device driver should not be using
this function

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Zhenghao Gu <imguzh@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231212031914.47339-1-imguzh@gmail.com

wifi: ath11k: Update Qualcomm Innovation Center, Inc. copyrights

Update the copyright for all ath11k files modified on behalf of
Qualcomm Innovation Center, Inc. in 2021 through 2023.

Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231128-ath12kcopyrights-v1-2-be0b7408cbac@quicinc.com

wifi: ath11k: remove unnecessary (void*) conversions

No need cast (void *) to (struct ath11k_base *),
struct hal_rx_msdu_link *), (struct ath11k_buffer_addr *) or
other types.

Signed-off-by: Wu Yunchuan <yunchuan@nfschina.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230919045150.524304-1-yunchuan@nfschina.com

wifi: ath11k: hal: cleanup debug message

Fix the debug message to follow the preferred style.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23

Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609142440.24643-13-kvalo@kernel.org

wifi: ath11k: debug: use all upper case in ATH11k_DBG_HAL

Somehow the character 'k' in ATH11k_DBG_HAL was in lower case. Change it to
upper case.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23

Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609142440.24643-12-kvalo@kernel.org

wifi: ath11k: remove manual mask names from debug messages

Now that the previous patch changed ath11k_dbg() to print the debug level
there's no need to have the level in the actual message anymore. So remove those.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23

Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609142440.24643-4-kvalo@kernel.org

wifi: ath11k: remap ce register space for IPQ5018

In IPQ5018 ce register space is moved out of wcss unlike
ipq8074 or ipq6018 and the space is not contiguous,
hence remap the CE registers to a new space to access them.

Register read/write is modified to check if the register to be written
falls in the CE register space and corresponding register is written.
Also adjust the interrupt register address to ce irq enable/disable.

Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1

Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-5-quic_kathirve@quicinc.com

wifi: ath11k: Fix miscellaneous spelling errors

Fix misspellings flagged by 'codespell'.

Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220909145535.20437-1-quic_jjohnson@quicinc.com

wifi: ath11k: Add multi TX ring support for WCN6750

Currently in the case of WCN6750, only one TCL ring is used for TX,
this is limiting the TX throughput in 160 MHz case, enabling multiple
TCL rings on WCN6750 has shown an improvement of nearly 300 Mbps in
the case of TCP TX, therefore add the support of multi TX ring for
WCN6750.

Currently TCL ring is selected based on CPU ID, this logic cannot be
applied for WCN6750 as there is chance of out of order TX of packets
and to avoid this, choose TCL ring based on flow hash so that packets
of the same flow will end up on same TCL ring. For the same reason,
TCL ring retry logic is also not applicable for WCN6750.

Also the mapping of TCL, WBM & RBM IDs for WCN6750 is different from
existing devices. Create a new TCM/WBM/RBM mapping for WCN6750.

Change does not impact existing ath11k devices.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-3-quic_mpubbise@quicinc.com

ath11k: Fix typo in comments

There is a typo(isn't') in comments.
It maybe 'isn't' instead of 'isn't''.

Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220704030004.16484-1-jiaming@nfschina.com

ath11k: HAL changes to support WCN6750

Add HAL changes required to support WCN6750. Offsets of some registers
for WCN6750 are different from other supported devices; move such
register offsets to platform specific ath11k_hw_regs.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-8-quic_mpubbise@quicinc.com

ath11k: Avoid false DEADLOCK warning reported by lockdep

With CONFIG_LOCKDEP=y and CONFIG_DEBUG_SPINLOCK=y, lockdep reports
below warning:

[ 166.059415] ============================================
[ 166.059416] WARNING: possible recursive locking detected
[ 166.059418] 5.15.0-wt-ath+ #10 Tainted: G W O
[ 166.059420] --------------------------------------------
[ 166.059421] kworker/0:2/116 is trying to acquire lock:
[ 166.059423] ffff9905f2083160 (&srng->lock){+.-.}-{2:2}, at: ath11k_hal_reo_cmd_send+0x20/0x490 [ath11k]
[ 166.059440]
but task is already holding lock:
[ 166.059442] ffff9905f2083230 (&srng->lock){+.-.}-{2:2}, at: ath11k_dp_process_reo_status+0x95/0x2d0 [ath11k]
[ 166.059491]
other info that might help us debug this:
[ 166.059492] Possible unsafe locking scenario:

[ 166.059493] CPU0
[ 166.059494] ----
[ 166.059495] lock(&srng->lock);
[ 166.059498] lock(&srng->lock);
[ 166.059500]
*** DEADLOCK ***

[ 166.059501] May be due to missing lock nesting notation

[ 166.059502] 3 locks held by kworker/0:2/116:
[ 166.059504] #0: ffff9905c0081548 ((wq_completion)events){+.+.}-{0:0}, at: process_one_work+0x1f6/0x660
[ 166.059511] #1: ffff9d2400a5fe68 ((debug_obj_work).work){+.+.}-{0:0}, at: process_one_work+0x1f6/0x660
[ 166.059517] #2: ffff9905f2083230 (&srng->lock){+.-.}-{2:2}, at: ath11k_dp_process_reo_status+0x95/0x2d0 [ath11k]
[ 166.059532]
stack backtrace:
[ 166.059534] CPU: 0 PID: 116 Comm: kworker/0:2 Kdump: loaded Tainted: G W O 5.15.0-wt-ath+ #10
[ 166.059537] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0059.2019.1112.1124 11/12/2019
[ 166.059539] Workqueue: events free_obj_work
[ 166.059543] Call Trace:
[ 166.059545] <IRQ>
[ 166.059547] dump_stack_lvl+0x56/0x7b
[ 166.059552] __lock_acquire+0xb9a/0x1a50
[ 166.059556] lock_acquire+0x1e2/0x330
[ 166.059560] ? ath11k_hal_reo_cmd_send+0x20/0x490 [ath11k]
[ 166.059571] _raw_spin_lock_bh+0x33/0x70
[ 166.059574] ? ath11k_hal_reo_cmd_send+0x20/0x490 [ath11k]
[ 166.059584] ath11k_hal_reo_cmd_send+0x20/0x490 [ath11k]
[ 166.059594] ath11k_dp_tx_send_reo_cmd+0x3f/0x130 [ath11k]
[ 166.059605] ath11k_dp_rx_tid_del_func+0x221/0x370 [ath11k]
[ 166.059618] ath11k_dp_process_reo_status+0x22f/0x2d0 [ath11k]
[ 166.059632] ? ath11k_dp_service_srng+0x2ea/0x2f0 [ath11k]
[ 166.059643] ath11k_dp_service_srng+0x2ea/0x2f0 [ath11k]
[ 166.059655] ath11k_pci_ext_grp_napi_poll+0x1c/0x70 [ath11k_pci]
[ 166.059659] __napi_poll+0x28/0x230
[ 166.059664] net_rx_action+0x285/0x310
[ 166.059668] __do_softirq+0xe6/0x4d2
[ 166.059672] irq_exit_rcu+0xd2/0xf0
[ 166.059675] common_interrupt+0xa5/0xc0
[ 166.059678] </IRQ>
[ 166.059679] <TASK>
[ 166.059680] asm_common_interrupt+0x1e/0x40
[ 166.059683] RIP: 0010:_raw_spin_unlock_irqrestore+0x38/0x70
[ 166.059686] Code: 83 c7 18 e8 2a 95 43 ff 48 89 ef e8 22 d2 43 ff 81 e3 00 02 00 00 75 25 9c 58 f6 c4 02 75 2d 48 85 db 74 01 fb bf 01 00 00 00 <e8> 63 2e 40 ff 65 8b 05 8c 59 97 5c 85 c0 74 0a 5b 5d c3 e8 00 6a
[ 166.059689] RSP: 0018:ffff9d2400a5fca0 EFLAGS: 00000206
[ 166.059692] RAX: 0000000000000002 RBX: 0000000000000200 RCX: 0000000000000006
[ 166.059694] RDX: 0000000000000000 RSI: ffffffffa404879b RDI: 0000000000000001
[ 166.059696] RBP: ffff9905c0053000 R08: 0000000000000001 R09: 0000000000000001
[ 166.059698] R10: ffff9d2400a5fc50 R11: 0000000000000001 R12: ffffe186c41e2840
[ 166.059700] R13: 0000000000000001 R14: ffff9905c78a1c68 R15: 0000000000000001
[ 166.059704] free_debug_processing+0x257/0x3d0
[ 166.059708] ? free_obj_work+0x1f5/0x250
[ 166.059712] __slab_free+0x374/0x5a0
[ 166.059718] ? kmem_cache_free+0x2e1/0x370
[ 166.059721] ? free_obj_work+0x1f5/0x250
[ 166.059724] kmem_cache_free+0x2e1/0x370
[ 166.059727] free_obj_work+0x1f5/0x250
[ 166.059731] process_one_work+0x28b/0x660
[ 166.059735] ? process_one_work+0x660/0x660
[ 166.059738] worker_thread+0x37/0x390
[ 166.059741] ? process_one_work+0x660/0x660
[ 166.059743] kthread+0x176/0x1a0
[ 166.059746] ? set_kthread_struct+0x40/0x40
[ 166.059749] ret_from_fork+0x22/0x30
[ 166.059754] </TASK>

Since these two lockes are both initialized in ath11k_hal_srng_setup,
they are assigned with the same key. As a result lockdep suspects that
the task is trying to acquire the same lock (due to same key) while
already holding it, and thus reports the DEADLOCK warning. However as
they are different spinlock instances, the warning is false positive.

On the other hand, even no dead lock indeed, this is a major issue for
upstream regression testing as it disables lockdep functionality.

Fix it by assigning separate lock class key for each srng->lock.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211209011949.151472-1-quic_bqiang@quicinc.com

ath11k: remove mod operator in dst ring processing

Replace use of mod operator with a manual wrap around
to avoid additional cost of using mod operation.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2

Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-10-git-send-email-ppranees@codeaurora.org

ath11k: allocate dst ring descriptors from cacheable memory

tcl_data and reo_dst rings are currently being allocated using
dma_allocate_coherent() which is non cacheable.

Allocating ring memory from cacheable memory area allows cached descriptor
access and prefetch next descriptors to optimize CPU usage during
descriptor processing on NAPI. Based on the hardware param we can enable
or disable this feature for the corresponding platform.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1

Co-developed-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-3-git-send-email-ppranees@codeaurora.org

ath11k: setup WBM_IDLE_LINK ring once again

For WCN6855, WBM idle link ring needs a reinit.
Without this reinit, firmware crash might happen occasionally.
This is requested by the hw team.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-5-jouni@codeaurora.org

ath11k: add hal support for QCN9074

Define the hal ring address and ring meta descriptor mask for
QCN9074. Move the platform specific address to the ath11k_hw_regs.
Define tx_mesh_enable ops in ath11k_hw_ops since its accessing
platform specific TCL descriptor.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-8-git-send-email-akolli@codeaurora.org

ath11k: remove unnecessary casts to u32

These casts are not needed. No changes in functionality.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-9-git-send-email-kvalo@codeaurora.org

ath11k: start a timer to update TCL HP

The timer is to check if TCL HP isn't updated to target.
The timer will postpone itself if there are TX operations
during the interval, otherwise the timer handler updates
the HP again so the index value in HP register will be
forwarded to target register, and the timer stops afterwards.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-5-git-send-email-kvalo@codeaurora.org

ath11k: enable shadow register configuration and access

To enable shadow register access, host needs to pass shadow
register configuration to firmware via qmi message. Host also
needs to update ring's HP or TP address to shadow register
address. The write operation to shadow register will be
forwarded to target register by hardware automatically, and
the write operation to shadow register is permitted even
when the target is in power save or sleep mode.

Update the shadow config whenever power up happens.

This feature is controlled by hw parameter supports_shadow_regs which is only
enabled for QCA6390.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-3-git-send-email-kvalo@codeaurora.org

ath11k: add packet log support for QCA6390

Add packet log support for QCA6390, otherwise the data connection will stall
within a minute or so. Enable it via debugfs and use trace-cmd to capture the
pktlogs.

echo 0xffff 1 > /sys/kernel/debug/ath11k/qca6390\ hw2.0/mac0/pktlog_filter

The mon status ring doesn't support interrupt so far, so host starts
a timer to reap this ring. The timer handler also reaps the
rxdma_err_dst_ring in case of monitor mode.

As QCA6390 requires bss created ahead of starting vdev, so check
vdev_start_delay for monitor mode.

For QCA6390, it uses wbm_desc_rel_ring to return descriptors.
It also uses rx_refill_buf_ring to fill mon buffer instead of
rxdma_mon_buf_ring.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601463073-12106-2-git-send-email-kvalo@codeaurora.org

ath11k: hal: assign msi_addr and msi_data to srng

QCA6390 uses MSI interrupt so it needs msi_addr and msi_data
to generate interrupt.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-7-git-send-email-kvalo@codeaurora.org

ath11k: ce: remove CE_COUNT() macro

This macro is evil as it's accesses ab variable in a hidden way. It's better
for readibility to access ab->hw_params.ce_count directly.

This is done in a separate patch to keep the patches simple. No functional changes.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-6-git-send-email-kvalo@codeaurora.org

ath11k: ce: support different CE configurations

QCA6390 uses only 9 Copy Engines while IPQ8074 may use 12, make it possible to
change CE configuration dynamically via hw_params.

The defines for host_ce_config_wlan and CE_COUNT are temporary solutions, they
will be removed in the following patches to keep things simple.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-4-git-send-email-kvalo@codeaurora.org

ath11k: hal: cleanup dynamic register macros

Now some of the HAL register macros access ab variable in a hidden way, make ab
variable visible in the macro by adding it as an argument.

This is done in a separate patch to keep the patches simple. No functional changes.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-3-git-send-email-kvalo@codeaurora.org

ath11k: hal: create hw_srng_config dynamically

On QCA6390 reg_start and reg_size values are different from IPQ8074 so we need
to change the values runtime. As we can't modify a static const variable
hw_srng_config directly, instead use it as a template, copy it and modify the
copy with correct values.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-12-git-send-email-kvalo@codeaurora.org

ath11k: pci: add HAL, CE and core initialisation

Define CE pipe/qmi config and setup pci irq for the
same. Call ath11k_core_init().

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-10-git-send-email-kvalo@codeaurora.org

ath11k: add simple PCI client driver for QCA6390 chipset

QCA6390 is a PCI based 11ax chipset, split AHB into own kernel module
ath11k_ahb.ko and add ath11k_pci.ko for PCI devices.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-5-git-send-email-kvalo@codeaurora.org

ath11k: Remove bus layer includes from upper layer

Bus level header files needs to be abstracted by upper
layer. Remove bus layer includes by adding appropriate header
files.

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200506094400.4740-4-govinds@codeaurora.org

ath11k: Add support for multibus support

Current design supports only AHB interface for
11ax chipset. Refactor the code by adding hif layer
for bus level abstraction to support PCI based device.

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200506094400.4740-2-govinds@codeaurora.org

ath11k: dump SRNG stats during FW assert

Dumping the SRNG stats during FW assert, this would help
in debugging ring stuck issues.

Co-developed-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath11k: driver for Qualcomm IEEE 802.11ax devices

ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first
supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k
uses mac80211 and supports AP, Station and Mesh modes.

Even though ath11k has some similar code as with ath10k (especially
the WMI layer) it was concluded to be simpler to have a "clean start"
for ath11k code base and not try to share the code with ath10k. This
makes maintenance easier and avoids major changes in ath10k, which
would have significantly increased the risk of regressions in existing
setups.

Even though the driver is very similar with ath10k but there are major
differences as well. The datapath is completely different. ath11k
supports multiple MACs, called "soc" in the firmware interface. And
there's only one WMI interface to support.

Currently ath11k supports only IEEE 802.11ac mode, but patches for
802.11ax are available and they will be submitted after ath11k is
accepted to upstream.

The firmware images are available from ath11k-firmware repository but
they will be also submitted to linux-firmware:

https://github.com/kvalo/ath11k-firmware

This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1.

The driver has had multiple authors who are listed in alphabetical
order below.

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>