wifi: ath11k: rearrange IRQ enable/disable in reset path

For non WoW suspend/resume, ath11k host powers down whole hardware
when suspend and powers up it when resume, the code path it goes
through is very like the ath11k reset logic.

In order to reuse that logic, rearrange IRQ handling in the reset
path.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30

Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-2-quic_bqiang@quicinc.com

wifi: ath11k: add support for QCA2066

QCA2066 is a PCI based DBS device. It is very similar to WCN6855
overall: they share the same PCI device ID, the same major and
minor version numbers, the same register address, and same HAL
descriptors etc. The most significant difference is that QCA2066
supports 3-antenna configuration while WCN6855 does not. To differentiate
them, subversion numbers are used. Currently four numbers are used
by QCA2066: 0x1019A0E1, 0x1019B0E1, 0x1019C0E1 and 0x1019D0E1.

Tested-on: QCA2066 hw2.1 PCI WLAN.HSP.1.1-03737-QCAHSPSWPL_V2_SILICONZ_CE-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240109021336.4143-3-quic_bqiang@quicinc.com

wifi: ath11k: support 2 station interfaces

Add hardware parameter support_dual_stations to indicate whether 2 station
interfaces are supported. For chips which support this feature, limit total
number of AP interface and mesh point to 1. The max interfaces are 3 for such
chips.

The chips affected are:

QCA6390 hw2.0
WCN6855 hw2.0
WCN6855 hw2.1

Other chips are not affected.

For affected chips, remove radar_detect_widths because now
num_different_channels is set to 2. radar_detect_widths can be set only when
num_different_channels is 1, see mac80211 function wiphy_verify_combinations
for details. This means that in affectected chips DFS cannot be enabled in AP
mode.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20230714023801.2621802-2-quic_cjhuang@quicinc.com

wifi: ath11k: add firmware-2.bin support

Firmware IE containers can dynamically provide various information
what firmware supports. Also it can embed more than one image so
updating firmware is easy, user just needs to update one file in
/lib/firmware/.

The firmware API 2 or higher will use the IE container format, the
current API 1 will not use the new format but it still is supported
for some time. Firmware API 2 files are named as firmware-2.bin
(which contains both amss.bin and m3.bin images) and API 1 files are
amss.bin and m3.bin.

Currently ath11k PCI driver provides firmware binary (amss.bin) path to
MHI driver, MHI driver reads firmware from filesystem and boots it. Add
provision to read firmware files from ath11k driver and provide the amss.bin
firmware data and size to MHI using a pointer.

Currently enum ath11k_fw_features is empty, the patches adding features will
add the flags.

With AHB devices there's no amss.bin or m3.bin, so no changes in how AHB
firmware files are used. But AHB devices can use future additions to the meta
data, for example in enum ath11k_fw_features.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9

Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Co-developed-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230727100430.3603551-4-kvalo@kernel.org

wifi: ath11k: Remove ath11k_base::bd_api

Currently struct ath11k_base defines the member bd_api. However, this
member is only accessed within ath11k_core_fetch_bdf(). Since the
scope is local just to that one function, remove it from ath11k_base
and instead just use a local stack variable.

No functional changes, compile tested only.

Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231013-ath11k_bd_api-v1-1-3fefe4629706@quicinc.com

wifi: ath11k: add chip id board name while searching board-2.bin for WCN6855

Sometimes board-2.bin does not have the board data which matched the
parameters such as bus type, vendor, device, subsystem-vendor,
subsystem-device, qmi-chip-id and qmi-board-id, then wlan will load fail.

Hence add another type which only matches the bus type and qmi-chip-id,
then the ratio of missing board data reduced.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230830060226.18664-1-quic_wgong@quicinc.com

wifi: ath11k: Add coldboot calibration support for QCN9074

QCN9074 supports 6 GHz, which has increased number of channels
compared to 5 GHz/2 GHz. So, to support coldboot calibration in
QCN9074 ATH11K_COLD_BOOT_FW_RESET_DELAY extended to 60 seconds. To
avoid code redundancy, fwreset_from_cold_boot moved to QMI and made
common for both ahb and pci. Coldboot calibration is enabled only in
FTM mode for QCN9074. QCN9074 requires firmware restart after coldboot,
hence enable cbcal_restart_fw in hw_params.

This support can be enabled/disabled using hw params for different
hardware. Currently it is not enabled for QCA6390.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230726141032.3061-3-quic_rajkbhag@quicinc.com

wifi: ath11k: Split coldboot calibration hw_param

QCN9074 enables coldboot calibration only in Factory Test Mode (FTM).
Hence, split cold_boot_calib to two hw_params for mission and FTM
mode.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230726141032.3061-2-quic_rajkbhag@quicinc.com

wifi: ath11k: Restart firmware after cold boot calibration for IPQ5018

Restart is required after cold boot calibration on IPQ5018. Otherwise,
we get the following exception:

[ 14.412829] qcom-q6-mpd cd00000.remoteproc: fatal error received: err_smem_ver.2.1:
[ 14.412829] QC Image Version : QC_IMAGE_VERSION_STRING=WLAN.HK.2.6.0.1-00974-QCAHKSWPL_SILICONZ-1
[ 14.412829] Image Variant : IMAGE_VARIANT_STRING=5018.wlanfw2.map_spr_spr_evalQ
[ 14.412829] DALSysLogEvent.c:174 Assertion 0 failed param0 :zero,param1 :zero,param2 :zero
[ 14.412829] Thread ID : 0x00000048 Thread name : WLAN RT0 Process ID : 0x00000001 Process name :wlan0
[ 14.412829]
[ 14.412829] Registers:
[ 14.412829] SP : 0x4c81c120
[ 14.412829] FP : 0x4c81c138
[ 14.412829] PC : 0xb022c590
[ 14.412829] SSR : 0x00000000
[ 14.412829] BADVA : 0x00000000
[ 14.412829] LR : 0xb0008490
[ 14.412829]
[ 14.412829] StackDump
[ 14.412829] from:0x4c81c120
[ 14.412829] to: 0x00000000:
[ 14.412829]
[ 14.463006] remoteproc remoteproc0: crash detected in cd00000.remoteproc: type fatal error

Fixes: 8dfe875aa24a ("wifi: ath11k: update hw params for IPQ5018")
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/TYZPR01MB55566969818BD4B49E770445C953A@TYZPR01MB5556.apcprd01.prod.exchangelabs.com

wifi: ath11k: remove manual mask names from debug messages

Now that the previous patch changed ath11k_dbg() to print the debug level
there's no need to have the level in the actual message anymore. So remove those.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23

Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609142440.24643-4-kvalo@kernel.org

wifi: ath11k: factory test mode support

Add support to process factory test mode commands (FTM) for calibration.
By default firmware start with NORMAL mode and to process the FTM commands
firmware needs to be restarted in FTM mode using module parameter ftm_mode.
The pre-request is all the radios should be down before starting the test.

When start command ATH11K_TM_CMD_TESTMODE_START is received, ar->state
is set to Test Mode. If the FTM command or event length is greater
than 256 bytes, it will be broken down into multiple segments and
encoded with TLV header if it is segmented commands, else it is sent
to firmware as it is.

On receiving UTF event from firmware, if it is segmented event, the driver
will wait until it receives all the segments and notify the complete
data to user application. In case the segmented sequence are missed or
lost from the firmware, driver will skip the already received partial data.

In case of unsegmented UTF event from firmware, driver notifies the
data to the user application as it comes. Applications handles
the data further.

Command to boot in ftm mode:

insmod ath11k ftm_mode=1

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Govindaraj Saminathan <quic_gsaminat@quicinc.com>
Co-developed-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230517135934.16408-4-quic_rajkbhag@quicinc.com

wifi: ath11k: add support default regdb while searching board-2.bin for WCN6855

Sometimes board-2.bin does not have the regdb data which matched the
parameters such as vendor, device, subsystem-vendor, subsystem-device
and etc. Add default regdb data with 'bus=%s' into board-2.bin for
WCN6855, then ath11k use 'bus=pci' to search regdb data in board-2.bin
for WCN6855.

kernel: [ 122.515808] ath11k_pci 0000:03:00.0: boot using board name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
kernel: [ 122.517240] ath11k_pci 0000:03:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 6179564
kernel: [ 122.517280] ath11k_pci 0000:03:00.0: failed to fetch regdb data for bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262 from ath11k/WCN6855/hw2.0/board-2.bin
kernel: [ 122.517464] ath11k_pci 0000:03:00.0: boot using board name 'bus=pci'
kernel: [ 122.518901] ath11k_pci 0000:03:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 6179564
kernel: [ 122.518915] ath11k_pci 0000:03:00.0: board name
kernel: [ 122.518917] ath11k_pci 0000:03:00.0: 00000000: 62 75 73 3d 70 63 69 bus=pci
kernel: [ 122.518918] ath11k_pci 0000:03:00.0: boot found match regdb data for name 'bus=pci'
kernel: [ 122.518920] ath11k_pci 0000:03:00.0: boot found regdb data for 'bus=pci'
kernel: [ 122.518921] ath11k_pci 0000:03:00.0: fetched regdb

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230517133959.8224-1-quic_wgong@quicinc.com

wifi: ath11k: enable SAR support on WCN6750

Currently, SAR is enabled only on WCN6855, enable this for WCN6750 too. This
functionality gets triggered, when the user space application calls
NL80211_CMD_SET_SAR_SPECS.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1

Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230328113455.11252-1-quic_youghand@quicinc.com

wifi: ath11k: Configure the FTM responder role using firmware capability flag

Fine Time Measurement(FTM) is offloaded feature to firmware.
Hence, the configuration of FTM responder role is done using
firmware capability flag instead of hw param.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Ganesh Babu Jothiram <quic_gjothira@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230317072034.8217-1-quic_gjothira@quicinc.com

wifi: ath11k: Add support to configure FTM responder role

Fine Timing Measurement(FTM) support is used to measure round trip
time between two nodes.

Enable FTM responder feature using hw_params on supported device.
Since FTM functionality is offloaded to firmware, adding the
interface allows user space to enable or disable FTM responder.
Also add support for advertising the same in extended capabilities.

QCA6390, WCN6855 and WCN6750 do not support this feature.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221220044435.10506-1-quic_rajkbhag@quicinc.com

wifi: ath11k: initialize hw_ops for IPQ5018

The ipq5018_ops is initialized for IPQ5018. This is different from
other platforms.

Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1

Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-7-quic_kathirve@quicinc.com

wifi: ath11k: update hal srng regs for IPQ5018

IPQ5018 hal srng register address & offsets are not
similar to IPQ8074/IPQ6018/QCN9074, hence define a
new set of srng register group data for IPQ5018.

Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1

Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-6-quic_kathirve@quicinc.com

wifi: ath11k: remap ce register space for IPQ5018

In IPQ5018 ce register space is moved out of wcss unlike
ipq8074 or ipq6018 and the space is not contiguous,
hence remap the CE registers to a new space to access them.

Register read/write is modified to check if the register to be written
falls in the CE register space and corresponding register is written.
Also adjust the interrupt register address to ce irq enable/disable.

Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1

Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-5-quic_kathirve@quicinc.com

wifi: ath11k: update ce configurations for IPQ5018

IPQ5018 is a single pdev device. Update host
and target CE configurations accordingly.

Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1

Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-4-quic_kathirve@quicinc.com

wifi: ath11k: update hw params for IPQ5018

Add new compatible string for IPQ5018 and add
required hw params for IPQ5018. The hw descriptors size and
datapath ops are similar to QCN9074, hence reuse the same.

Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1

Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-3-quic_kathirve@quicinc.com

wifi: ath11k: Trigger sta disconnect on hardware restart

Currently after the hardware restart triggered from the driver, the
station interface connection remains intact, since a disconnect trigger
is not sent to userspace. This can lead to a problem in targets where
the wifi mac sequence is added by the firmware.

After the target restart, its wifi mac sequence number gets reset to
zero. Hence AP to which our device is connected will receive frames with
a wifi mac sequence number jump to the past, thereby resulting in the
AP dropping all these frames, until the frame arrives with a wifi mac
sequence number which AP was expecting.

To avoid such frame drops, its better to trigger a station disconnect
upon target hardware restart which can be done with API
ieee80211_reconfig_disconnect exposed to mac80211.

The other targets are not affected by this change, since the hardware
params flag is not set.

Reported-by: kernel test robot <lkp@intel.com>

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1

Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221104085403.11025-1-quic_youghand@quicinc.com

wifi: ath11k: fix monitor vdev creation with firmware recovery

During firmware recovery, the monitor interface is not
getting created in the driver and firmware since
the respective flags are not updated properly.

So after firmware recovery is successful, when monitor
interface is brought down manually, firmware assertion
is observed, since we are trying to bring down the
interface which is not yet created in the firmware.

Fix this by updating the monitor flags properly per
phy#, during firmware recovery.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221014155054.11471-1-quic_nmaran@quicinc.com

wifi: ath11k: stop tx queues immediately upon firmware exit

Currently, recovery flag is set immediately upon firmware
exit but tx queues are stopped once firmware arrives back
and is ready which is during ath11k_core_restart. Once
ieee80211 hw restart is completed, tx queues are resumed.
If during the time delta between firmware exit and firmware
ready, mac80211 send packets, currently ath11k will drop it
since recovery flag will be set. But warning prints will
come -
"ath11k c000000.wifi: failed to transmit frame -108"

If more tx packets are there, this could lead to flooding
of above print.

However, actually tx queues should be stopped immediately
when firmware leaves. This will prevent packets to get
dropped when firmware is recovering.

Add fix to stop tx queues immediately after firmware exit.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1

Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220923170235.18873-1-quic_adisi@quicinc.com

wifi: ath11k: Add spectral scan support for 160 MHz

There are two types of 160 MHz spectral scan support mentioned below

1. Fragmented approach
2. Single event approach

In this fragmented approach, single 160 MHz will be split as two
80 MHz buffer. First fft sample buffer will contain spectral scan
result of primary 80 MHz and the second fft sample buffer will contain
secondary 80 MHz and here cfreq1 and cfreq2 will be mentioned.
In case of 160 MHz on 36th channel will contain cfreq1 as 5210 and
cfreq2 as 5290. Chipsets which support this approach are IPQ8074/IPQ6018.

Replacing freq1 with freq2 in every secondary sepctral scan event to
distinguish between two different 80 MHz spectral event data.

In the 2nd approach each fft sample buffer will contain spectral scan
result for whole 160 MHz by mentioning cfreq1 as 5250 which is center
frequency of whole 160 MHz. Chipset which support this approach is QCN9074.

Host will receive spectral event from target for every 5 fft samples.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01120-QCAHKSWPL-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01120-QCAHKSWP

Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725055001.15194-1-quic_tamizhr@quicinc.com

wifi: ath11k: move firmware stats out of debugfs

Currently, firmware stats, comprising pdev, vdev and beacon stats are
part of debugfs. In firmware pdev stats, firmware reports the final
Tx power used to transmit each packet. If driver wants to know the
final Tx power being used at firmware level, it can leverage from
firmware pdev stats.

Move firmware stats out of debugfs context in order to leverage
the final Tx power reported in it even when debugfs is disabled.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603082814.31466-2-quic_adisi@quicinc.com

wifi: ath11k: change complete() to complete_all() for scan.completed

Currently commit 1f682dc9fb37 ("ath11k: reduce the wait time of 11d scan
and hw scan while add interface") introduced a wait_for_completion_timeout
operation for ar->scan.completed, another one is existed in ath11k_scan_stop(),
then ath11k has two places to wait for the ar->scan.completed and they
run in different thread, thus it is possible to happend that the two
thread both enter wait status. To handle this scenario, ath11k should
change the complete() to complete_all() for the ar->scan.completed. This
also work well when it is only one thread wait for ar->scan.completed.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220919024413.25083-1-quic_wgong@quicinc.com

wifi: ath11k: Add WoW support for WCN6750

Add support for WoW on WCN6750 chipset.

Unlike other chips where WoW exit happens after sending WoW wakeup
WMI command, exit from WoW suspend in the case of WCN6750 happens
upon sending a WoW exit SMP2P (Shared memory point to point) message
to the firmware.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220902112520.24804-3-quic_mpubbise@quicinc.com

wifi: ath11k: Increase TCL data ring size for WCN6750

Increase TCL data ring size to 2048 for WCN6750. This is
needed to meet 160 MHz TX throughput.

Add a new hw_param to indicate the TX ring size for
individual devices.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-4-quic_mpubbise@quicinc.com

wifi: ath11k: Add multi TX ring support for WCN6750

Currently in the case of WCN6750, only one TCL ring is used for TX,
this is limiting the TX throughput in 160 MHz case, enabling multiple
TCL rings on WCN6750 has shown an improvement of nearly 300 Mbps in
the case of TCP TX, therefore add the support of multi TX ring for
WCN6750.

Currently TCL ring is selected based on CPU ID, this logic cannot be
applied for WCN6750 as there is chance of out of order TX of packets
and to avoid this, choose TCL ring based on flow hash so that packets
of the same flow will end up on same TCL ring. For the same reason,
TCL ring retry logic is also not applicable for WCN6750.

Also the mapping of TCL, WBM & RBM IDs for WCN6750 is different from
existing devices. Create a new TCM/WBM/RBM mapping for WCN6750.

Change does not impact existing ath11k devices.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-3-quic_mpubbise@quicinc.com

wifi: ath11k: implement SRAM dump debugfs interface

On-board SRAM contains valuable information for firmware debugging so
add a new file named "sram" to debugfs with which we can dump SRAM
content using following the following:

cp /sys/kernel/debug/ath11k/wcn6855\ hw2.0/sram /tmp/sram

Currently this feature is enabled for QCA6390 and WCN6855.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220802075533.1744-3-quic_bqiang@quicinc.com

ath11k: Enable remain-on-channel support on WCN6750

Enable remain on channel support on WCN6750 as it is needed for
GAS, Passpoint.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220901080656.3450-1-quic_mpubbise@quicinc.com

wifi: ath11k: Add support to connect to non-transmit MBSSID profiles

Add support to connect to a non-transmit MBSSID AP profile.

Non-transmit MBSSID profile parameters are passed to the firmware
via WMI VDEV UP command and this helps firmware to track MBSSID
profile within the multi-BSS beacon and report beacon loss if
any.

WCN6750, QCA6390 & WCN6855 firmwares have the support and hence
enable the support on these hardwares.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220901080616.29414-1-quic_mpubbise@quicinc.com

wifi: ath11k: Add cold boot calibration support on WCN6750

Add cold boot calibration support on WCN6750. Unlike other
chipsets where firmware(FW) is restarted after cold boot
calibration is completed, it is recommended not to restart
the firmware for WCN6750.

For WCN6750, FW sends both CAL_DONE & FW_READY QMI indication
to the driver after cold boot calibration is completed.

QMI message flow for WCN6750 with cold boot support:
FW_INIT_DONE to HOST -> CALIBRATION Mode to FW -> CAL_DONE to Host ->
FW_READY to Host -> MODE_ON to FW

QMI message flow for other chipsets with cold boot support:
FW_INIT_DONE to Host -> CALIBRATION Mode to FW -> FW_READY to Host ->
Trigger FW restart -> FW_INIT_DONE to HOST -> MODE_ON to FW

QMI message flow for chipsets without cold boot support:
FW_INIT_DONE to Host -> MODE_ON to FW

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134909.15626-3-quic_mpubbise@quicinc.com

wifi: ath11k: Register shutdown handler for WCN6750

When the system shuts down, SMMU driver will be stopped and
will not assist in IOVA translations. SMMU driver expects all
of its consumers to shutdown before shutting down itself.
WCN6750 being one of the consumer device should not perform any
DMA operations after the SMMU has shutdown which will otherwise
result in SMMU faults.

SMMU driver will call the shutdown() callback of all its
consumer devices and the consumers shall stop further DMA
activity after the invocation of their respective shutdown()
callbacks.

Register the shutdown() callback to the platform core for WCN6750.
Change will not impact other AHB ath11k devices.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134710.15523-1-quic_mpubbise@quicinc.com

Revert "ath11k: add support for hardware rfkill for QCA6390"

This reverts commit ec038c6127fa772d2c5604e329f22371830d5fa6. Tyler reported
that on L390 Yoga Thinkpad with QCA6390 the suspend was failing because of this commit.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9

Link: https://bugzilla.kernel.org/show_bug.cgi?id=215881
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220708164656.29549-1-kvalo@kernel.org

wifi: ath11k: Fix register write failure on QCN9074

Commit 56c8ccf331bd ("ath11k: Add register access logic for WCN6750")
regressed QCN9074. With the above mentioned commit, writes are failing
for some registers on QCN9074 although the device seems to work
normally.

ath11k_pci 0000:03:00.0: failed to set pcie link register0x01e0e0a8: 0xffffffff != 0x00000010
ath11k_pci 0000:03:00.0: failed to set sysclk: -110

PCIe devices in ath11k (QCA6390, WCN6855, QCN9074, WCN6750) use window
concept for register accesses. There are two schemes, dynamic & static
window.

In dynamic window scheme, a single window(region in the BAR) is mapped
either to CE or DP register windows at any give time. QCA6390 & WCN6855
follow this scheme for register accesses.

In static window scheme, CE & DP register windows are statically mapped
to separate regions with in the BAR so that there is no switching of
register windows between CE & DP register accesses. QCN9074 & WCN6750
follow this scheme although the window start offsets are different for
QCN9074 & WCN6750.

QCN9074 uses 3rd & 2nd window for DP & CE register accesses respectively
whereas WCN6750 uses 1st & 2nd window for DP & CE. In QCN9074, along with
2nd & 3rd windows, 1st window is also used for certain configurations
which commit 56c8ccf331bd ("ath11k: Add register access logic for WCN6750")
did not account for and hence the regression.

Fix this by going back to the original way of accessing the registers on
QCN9074. Since this diverges from WCN6750 way of accessing registers, it
is required to register window_read32/window_write32() pci_ops for WCN6750.
We can also get rid of dp_window_idx & ce_window_idx members in hw_params,
so remove them.

Also add a new API ath11k_pcic_register_pci_ops() for registering pci_ops
to the ath11k core. This API checks for mandatory pci_ops() and reports
error if those are missing. Also initialize unused pci_ops to NULL.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1

Fixes: 56c8ccf331bd ("ath11k: Add register access logic for WCN6750")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220608062954.27792-1-quic_mpubbise@quicinc.com

ath11k: fix netdev open race

Make sure to allocate resources needed before registering the device.

This specifically avoids having a racing open() trigger a BUG_ON() in
mod_timer() when ath11k_mac_op_start() is called before the
mon_reap_timer as been set up.

I did not see this issue with next-20220310, but I hit it on every probe
with next-20220511. Perhaps some timing changed in between.

Here's the backtrace:

[ 51.346947] kernel BUG at kernel/time/timer.c:990!
[ 51.346958] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
...
[ 51.578225] Call trace:
[ 51.583293] __mod_timer+0x298/0x390
[ 51.589518] mod_timer+0x14/0x20
[ 51.595368] ath11k_mac_op_start+0x41c/0x4a0 [ath11k]
[ 51.603165] drv_start+0x38/0x60 [mac80211]
[ 51.610110] ieee80211_do_open+0x29c/0x7d0 [mac80211]
[ 51.617945] ieee80211_open+0x60/0xb0 [mac80211]
[ 51.625311] __dev_open+0x100/0x1c0
[ 51.631420] __dev_change_flags+0x194/0x210
[ 51.638214] dev_change_flags+0x24/0x70
[ 51.644646] do_setlink+0x228/0xdb0
[ 51.650723] __rtnl_newlink+0x460/0x830
[ 51.657162] rtnl_newlink+0x4c/0x80
[ 51.663229] rtnetlink_rcv_msg+0x124/0x390
[ 51.669917] netlink_rcv_skb+0x58/0x130
[ 51.676314] rtnetlink_rcv+0x18/0x30
[ 51.682460] netlink_unicast+0x250/0x310
[ 51.688960] netlink_sendmsg+0x19c/0x3e0
[ 51.695458] ____sys_sendmsg+0x220/0x290
[ 51.701938] ___sys_sendmsg+0x7c/0xc0
[ 51.708148] __sys_sendmsg+0x68/0xd0
[ 51.714254] __arm64_sys_sendmsg+0x28/0x40
[ 51.720900] invoke_syscall+0x48/0x120

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Fixes: 840c36fa727a ("ath11k: dp: stop rx pktlog before suspend")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220517103436.15867-1-johan+linaro@kernel.org

ath11k: Reuse the available memory after firmware reload

Ath11k allocates memory when firmware requests memory in QMI.
Coldboot calibration and firmware recovery uses firmware reload.
On firmware reload, firmware sends memory request again. If Ath11k
allocates memory on first firmware boot, reuse the available
memory. Also check if the segment type and size is same
on the next firmware boot. Reuse if segment type/size is
same as previous firmware boot else free the segment and
allocate the segment with size/type.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00752-QCAHKSWPL_SILICONZ-1

Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506141448.10340-1-quic_akolli@quicinc.com

ath11k: Designating channel frequency when sending management frames

In case of Passpoint, the WLAN interface may be requested to
remain on a specific channel and then to send some management
frames on that channel. Now chanfreq of wmi_mgmt_send_cmd is set
as 0, as a result firmware may choose a default but wrong channel.
Fix it by assigning chanfreq field with the designated channel.

This change only applies to WCN6855 and QCA6390, other chips are
not affected.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-4-quic_bqiang@quicinc.com

ath11k: Implement remain-on-channel support

Add remain on channel support, it is needed in several
scenarios such as Passpoint etc.

Currently this is supported by QCA6390, WCN6855, IPQ8074,
IPQ6018 and QCN9074.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-2-quic_bqiang@quicinc.com

ath11k: reset 11d state in process of recovery

When doing simulate_fw_crash operation periodically with a short interval
time such as 10 seconds, it is easy happened WMI command timed out for
WMI_SCAN_CHAN_LIST_CMDID in ath11k_reg_update_chan_list().

log:
[42287.610053] ath11k_pci 0000:01:00.0: wmi command 12291 timeout
[42287.610064] ath11k_pci 0000:01:00.0: failed to send WMI_SCAN_CHAN_LIST cmd
[42287.610073] ath11k_pci 0000:01:00.0: failed to perform regd update : -11

Note that this issue does not occur with a longer interval such as 20 seconds.

The reason the issue occurs with a shorter interval is the following steps:
1) Upon initial boot, or after device recovery, the initial hw scan plus
the 11d scan will run, and when 6 GHz support is present, these scans
can take up to 12 seconds to complete, so ath11k_reg_update_chan_list()
is still waiting the completion of ar->completed_11d_scan.
2) If a simulate_fw_crash operation is received during this time, those
scans do not complete, and ath11k_core_pre_reconfigure_recovery()
complete the ar->completed_11d_scan, then ath11k_reg_update_chan_list()
wakeup and start to send WMI_SCAN_CHAN_LIST_CMDID, but firmware is crashed
at this moment, so wmi timed out occur.

To address this issue, reset the 11d state during device recovery so that
WMI_SCAN_CHAN_LIST_CMDID does not timed out for short interval time such
as 10 seconds.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Fixes: 1f682dc9fb37 ("ath11k: reduce the wait time of 11d scan and hw scan while add interface")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220505034636.29582-1-quic_wgong@quicinc.com

ath11k: Datapath changes to support WCN6750

HAL RX descriptor for WCN6750 is same as QCN9074, this
means that the size of the HAL RX decriptor and the DP
APIs that WCN6750 requires to enable datapath should be
initialized with that of QCN9074's RX descriptor size
and the DP APIs respectively. There is one change wrt to
REO configuration though, REO configuration for WCN6750
follows WCN6855, therefore use reo_setup() of WCN6855
for WCN6750.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-9-quic_mpubbise@quicinc.com

ath11k: HAL changes to support WCN6750

Add HAL changes required to support WCN6750. Offsets of some registers
for WCN6750 are different from other supported devices; move such
register offsets to platform specific ath11k_hw_regs.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-8-quic_mpubbise@quicinc.com

ath11k: Add QMI changes for WCN6750

In the case of WCN6750, FW doesn't request for DDR memory
via QMI, instead it uses a fixed 12MB reserved Memory region
in the DDR which is called as MSA region. As a result, QMI
message sequence is not same as other ath11k supported devices.

Also, M3 firmware will be bundled into the FW and will be
downloaded to the target as part of Q6 boot.

This is the QMI flow in the case of WCN6750,

1) QMI firmware indication REQ/RESP
2) QMI host capability REQ/RESP
3) QMI target capability REQ/RESP
4) QMI device info REQ/RESP
5) QMI BDF download
6) QMI FW ready

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-7-quic_mpubbise@quicinc.com

ath11k: Add register access logic for WCN6750

WCN6750 uses static window mapping to access the HW registers.
Unlike QCN9074 which uses 3rd window for UMAC and 2nd window
for CE register access, WCN6750 uses 1st window for UMAC
and 2nd window for CE registers.

Also, refactor the code so that WCN6750 can use the existing
ath11k_pci_read32/write32() APIs for accessing the registers.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-5-quic_mpubbise@quicinc.com

ath11k: Add HW params for WCN6750

WCN6750 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.

Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.

A new variable hybrid_bus_type is defined in hw_params to indicate the
hybrid nature of the device.

Add HW params for WCN6750.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-4-quic_mpubbise@quicinc.com

ath11k: Move parameters in bus_params to hw_params

In ath11k, bus_params were added with an intention to hold
parameters related to bus (AHB/PCI), but this is not true
as some bus parameters being different between chipsets of
the same bus.

With the addition of WCN6750 to ath11k, bus parameters are
going to be entirely different among AHB devices. Therefore,
it is wise to move bus_params to hw_params and get rid of
bus_params entirely.

Also, mhi_support parameter is not used anywhere in the driver,
remove it from bus_params.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-3-quic_mpubbise@quicinc.com

ath11k: read country code from SMBIOS for WCN6855/QCA6390

This read the country code from SMBIOS and send the country code
to firmware, firmware will indicate the regulatory domain info of the
country code and then ath11k will use the info.

dmesg:
[ 1242.637173] ath11k_pci 0000:02:00.0: chip_id 0x2 chip_family 0xb board_id 0xff soc_id 0x400c0200
[ 1242.637176] ath11k_pci 0000:02:00.0: fw_version 0x110b09e5 fw_build_timestamp 2021-06-22 09:32 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02533-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
[ 1242.637253] ath11k_pci 0000:02:00.0: worldwide regdomain setting from SMBIOS
[ 1242.637259] ath11k_pci 0000:02:00.0: bdf variant name not found.
[ 1242.637261] ath11k_pci 0000:02:00.0: SMBIOS bdf variant name not set.
[ 1242.637263] ath11k_pci 0000:02:00.0: DT bdf variant name not set.
[ 1242.927543] ath11k_pci 0000:02:00.0: set current country pdev id 0 alpha2 00

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220421023501.32167-1-quic_wgong@quicinc.com

ath11k: Update WBM idle ring HP after FW mode on

Currently, WBM idle ring HP is updated much before the shadow
configuration is sent to the FW. Any update to the shadow
registers before FW mode on request would not be reflected
on to the actual HW registers failing to bring up the device.
Send FW mode ON QMI request before WBM idle ring HP update
to fix this problem.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-12-quic_mpubbise@quicinc.com

ath11k: Do not put HW in DBS mode for WCN6750

Though WCN6750 is a single PDEV device, it is not a
DBS solution. So, do not put HW in DBS mode for WCN6750.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-10-quic_mpubbise@quicinc.com

ath11k: Add support for SAR

Add ath11k_mac_op_set_bios_sar_specs() to ath11k_ops, this function is called
when user space application calls NL80211_CMD_SET_SAR_SPECS. ath11k also
registers SAR type and frequency ranges to wiphy so user space can query SAR
capabilities.

This feature is currently enabled for WCN6855.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401120948.1312956-3-quic_bqiang@quicinc.com

ath11k: Fix spelling mistake "reseting" -> "resetting"

There is a spelling mistake in an ath11k_warn message. Fix it.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220407102820.613881-1-colin.i.king@gmail.com

ath11k: Remove unnecessary delay in ath11k_core_suspend

The intended delay in ath11k_core_suspend is introduced in commit
d1b0c33850d2 ("ath11k: implement suspend for QCA6390 PCI devices"),
now with ath11k_mac_wait_tx_complete added in commit ba9177fcef21
("ath11k: Add basic WoW functionalities"), that delay is not
necessary now, so remove it.

This is found in code review.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220331002105.1162099-1-quic_bqiang@quicinc.com

ath11k: Remove core PCI references from PCI common code

Remove core PCI and ath11k PCI references(struct ath11k_pci)
from PCI common code. Since, PCI common code will be used
by hybrid bus devices, this code should be independent
from ATH11K PCI references and Linux core PCI references
like struct pci_dev.

Since this change introduces function callbacks for bus wakeup
and bus release operations, wakeup_mhi HW param is no longer
needed and hence it is removed completely. Alternatively, bus
wakeup/release ops for QCA9074 are initialized to NULL as
QCA9704 does not need bus wakeup/release for register accesses.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-6-quic_mpubbise@quicinc.com

ath11k: reduce the wait time of 11d scan and hw scan while add interface

Currently ath11k will wait 11d scan complete while add interface in
ath11k_mac_op_add_interface(), when system resume without enable
wowlan, ath11k_mac_op_add_interface() is called for each resume, thus
it increase the resume time of system. And ath11k_mac_op_hw_scan()
after ath11k_mac_op_add_interface() also needs some time cost because
the previous 11d scan need more than 5 seconds when 6 GHz is enabled,
then the scan started event will indicated to ath11k after the 11d
scan completed.

While 11d scan/hw scan is running in firmware, if ath11k update channel
list to firmware by WMI_SCAN_CHAN_LIST_CMDID, then firmware will cancel
the current scan which is running, it lead the scan failed. The patch
commit 9dcf6808b253 ("ath11k: add 11d scan offload support") used
finish_11d_scan/finish_11d_ch_list/pending_11d to synchronize the 11d
scan/hw scan/channel list between ath11k/firmware/mac80211 and to avoid
the scan fail.

Add wait operation before ath11k update channel list, function
ath11k_reg_update_chan_list() will wait until the current 11d scan/hw
scan completed. And remove the wait operation of start 11d scan and
waiting channel list complete in hw scan. After these changes, resume
time cost reduce about 5 seconds and also hw scan time cost reduced
obviously, and scan failed not seen.

The 11d scan is sent to firmware only one time for each interface added
in mac.c, and it is moved after the 1st hw scan because 11d scan will
cost some time and thus leads the AP scan result update to UI delay.
Currently priority of ath11k's hw scan is WMI_SCAN_PRIORITY_LOW, and
priority of 11d scan in firmware is WMI_SCAN_PRIORITY_MEDIUM, then the
11d scan which sent after hw scan will cancel the hw scan in firmware,
so change the priority to WMI_SCAN_PRIORITY_MEDIUM for the hw scan which
is in front of the 11d scan, thus it will not happen scan cancel in
firmware.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Fixes: 9dcf6808b253 ("ath11k: add 11d scan offload support")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328035832.14122-1-quic_wgong@quicinc.com

ath11k: add support to search regdb data in board-2.bin for WCN6855

Currently ath11k only download the same regdb.bin file for all WCN6855
chips, actually ath11k needs to distinguish all different WCN6855 chips.

This is to re-use the string type which include bus, chip id, board id,
vendor, device, subsystem-vendor, subsystem-device and variant for
WCN6855 to distinguish different regdb in board-2.bin.

ath11k will first load board-2.bin and search in it for the regdb data
with the above parameters, if matched one regdb data, then download it
to firmware, if not matched any one, then ath11k will download the file
regdb.bin to firmware.

Add enum value ATH11K_BD_IE_REGDB and enum type ath11k_bd_ie_regdb_type
to distinguish regdb data and board data since they are in the same file
board-2.bin.

This only take effect for WCN6855 which supports regdb in hardware parameters.

Test log:
[ 3833.091948] ath11k_pci 0000:05:00.0: boot using board name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[ 3833.092072] ath11k_pci 0000:05:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 205316
[ 3833.092079] ath11k_pci 0000:05:00.0: board name
[ 3833.092083] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092088] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 31 -id=1
[ 3833.092091] ath11k_pci 0000:05:00.0: board name
[ 3833.092095] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092099] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 32 -id=2
[ 3833.092102] ath11k_pci 0000:05:00.0: board name
[ 3833.092105] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092109] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 33 -id=3
[ 3833.092112] ath11k_pci 0000:05:00.0: board name
[ 3833.092116] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 3833.092119] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c 7cb,device=1103,
[ 3833.092123] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 3833.092126] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d =17cb,subsystem-
[ 3833.092130] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d device=3374,qmi-
[ 3833.092133] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f chip-id=2,qmi-bo
[ 3833.092137] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 36 2c 76 61 72 69 61 ard-id=266,varia
[ 3833.092140] ath11k_pci 0000:05:00.0: 00000070: 6e 74 3d 48 50 5f 47 38 5f 4c 61 6e 63 69 61 31 nt=HP_G8_Lancia1
[ 3833.092144] ath11k_pci 0000:05:00.0: 00000080: 35 5
[ 3833.092147] ath11k_pci 0000:05:00.0: board name
[ 3833.092150] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 3833.092154] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c 7cb,device=1103,
[ 3833.092157] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 3833.092161] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d =17cb,subsystem-
[ 3833.092165] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d device=3374,qmi-
[ 3833.092168] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f chip-id=2,qmi-bo
[ 3833.092172] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 36 ard-id=266
[ 3833.092206] ath11k_pci 0000:05:00.0: board name
[ 3833.092209] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[ 3833.092213] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c 7cb,device=1103,
[ 3833.092216] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[ 3833.092220] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d =17cb,subsystem-
[ 3833.092223] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d device=3374,qmi-
[ 3833.092227] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f chip-id=2,qmi-bo
[ 3833.092230] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 32 ard-id=262
[ 3833.092234] ath11k_pci 0000:05:00.0: boot found match regdb data for name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[ 3833.092238] ath11k_pci 0000:05:00.0: board name
[ 3833.092241] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092245] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 31 31 -id=11
[ 3833.092248] ath11k_pci 0000:05:00.0: board name
[ 3833.092251] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092255] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 32 32 -id=22
[ 3833.092258] ath11k_pci 0000:05:00.0: board name
[ 3833.092261] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70 bus=pci,qmi-chip
[ 3833.092265] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 33 33 -id=33
[ 3833.092268] ath11k_pci 0000:05:00.0: boot found regdb data for 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[ 3833.092272] ath11k_pci 0000:05:00.0: fetched regdb

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220319023543.14288-4-quic_wgong@quicinc.com

ath11k: store and send country code to firmware after recovery

Currently ath11k does not send the country code to firmware after device
recovery, as a result the regdomain info is reported from firmware by
default. Regdomain info is important, so ath11k also need to restore
it to the value which was used before recovery.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220324011856.11014-1-quic_wgong@quicinc.com

ath11k: Add peer rhash table support

When more clients (128) are connected, the UL data traffic
KPI measurement is low compared to single client. This issue
is due to more CPU cycles spent on the peer lookup operation
with more clients. So reduce the peer lookup operation by
modifying the linear based lookup operation into the rhash
based lookup operation. This improve the peak throughput
measurement. Since this is a software algorithm change, it is
applicable for all the platforms.

TCP UL 128 Clients test case Observation (64bit system):
Previous: ~550 Mbps
Now : ~860 Mbps

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644036628-5334-1-git-send-email-quic_periyasa@quicinc.com

ath11k: add read variant from SMBIOS for download board data

This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220315104721.26649-3-quic_wgong@quicinc.com

ath11k: add fallback board name without variant while searching board-2.bin

Sometimes it has a variant value which read from DT or SMBIOS by
ath11k, and meanwhile it does not have the matched board name in
board-2.bin, then it will failed at boot up phase.

Add fallback board name which removed variant value and search again
in board-2.bin when failed with variant and try to load the board
data again to increase boot up success rate.

dmesg log after this patch:
[169547.248472] ath11k_pci 0000:05:00.0: boot using board name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262,variant=test'
[169547.248565] ath11k_pci 0000:05:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 180324
[169547.248568] ath11k_pci 0000:05:00.0: board name
[169547.248570] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[169547.248571] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c 7cb,device=1103,
[169547.248572] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[169547.248574] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d =17cb,subsystem-
[169547.248575] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d device=3374,qmi-
[169547.248576] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f chip-id=2,qmi-bo
[169547.248577] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 32 ard-id=262
[169547.248578] ath11k_pci 0000:05:00.0: board name
[169547.248579] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[169547.248581] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c 7cb,device=1103,
[169547.248582] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[169547.248583] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d =17cb,subsystem-
[169547.248584] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d device=3374,qmi-
[169547.248585] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f chip-id=2,qmi-bo
[169547.248587] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 36 ard-id=266
[169547.248588] ath11k_pci 0000:05:00.0: board name
[169547.248589] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[169547.248590] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c 7cb,device=1103,
[169547.248591] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[169547.248592] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d =17cb,subsystem-
[169547.248594] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d device=3374,qmi-
[169547.248595] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 31 38 2c 71 6d 69 2d 62 chip-id=18,qmi-b
[169547.248596] ath11k_pci 0000:05:00.0: 00000060: 6f 61 72 64 2d 69 64 3d 32 36 36 oard-id=266
[169547.248597] ath11k_pci 0000:05:00.0: failed to fetch board data for bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262,variant=test from ath11k/WCN6855/hw2.0/board-2.bin
[169547.248476] ath11k_pci 0000:05:00.0: boot using board name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[169547.248634] ath11k_pci 0000:05:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 180324
[169547.248636] ath11k_pci 0000:05:00.0: board name
[169547.248637] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31 bus=pci,vendor=1
[169547.248638] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c 7cb,device=1103,
[169547.248639] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72 subsystem-vendor
[169547.248641] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d =17cb,subsystem-
[169547.248642] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d device=3374,qmi-
[169547.248643] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f chip-id=2,qmi-bo
[169547.248645] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 32 ard-id=262
[169547.248646] ath11k_pci 0000:05:00.0: boot found match for name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[169547.248647] ath11k_pci 0000:05:00.0: boot found board data for 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[169547.248649] ath11k_pci 0000:05:00.0: using board api 2

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220315104721.26649-2-quic_wgong@quicinc.com

ath11k: enable PLATFORM_CAP_PCIE_GLOBAL_RESET QMI host capability

In Qualcomm ARM platforms there is WL_EN pin and other power regulators
which can be controlled at platform side to completely reset the chip.
For most of x86 and other platforms, the chip is connected via PCIe M.2
interface, and there is no way to control WL_EN pin. Instead the host
driver needs to reset the chip via PCIE_SOC_GLOBAL_RESET hardware
register, just like ath11k does currently.

But when using PCIE_SOC_GLOBAL_RESET there are some hardware registers
which are not cleared/restored. To handle those cases we can enable
PLATFORM_CAP_PCIE_GLOBAL_RESET QMI host capability to tell the firmware
to do some platform specific operations after firmware download.

This does not fix any known issues, but is recommended by the firmware
team, so enable the capability on QCA6390 and WCN6855 PCI devices. It is
currently unclear if this should be enabled also on QCN9074, so leave it
disabled for now. On AHB devices this is not needed as they don't use
PCIE_SOC_GLOBAL_RESET.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211011055602.77342-1-bqiang@codeaurora.org

ath11k: add synchronization operation between reconfigure of mac80211 and ath11k_base

ieee80211_reconfig() of mac80211 is the main function for recovery of
each ieee80211_hw and ath11k, and ath11k_core_reconfigure_on_crash()
is the main function for recovery of ath11k_base, it has more than
one ieee80211_hw and ath11k for each ath11k_base, so it need to add
synchronization between them, otherwise it has many issue.

For example, when ath11k_core_reconfigure_on_crash() is not complete,
mac80211 send a hw scan request to ath11k, it leads firmware crash,
because firmware has not been initialized at that moment, firmware
is only finished downloaded and loaded, it can not receive scan
command.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-3-quic_wgong@quicinc.com

ath11k: add support for device recovery for QCA6390/WCN6855

Currently ath11k has device recovery logic, it is introduced by this
patch "ath11k: Add support for subsystem recovery" which is upstream
by https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git/commit/?h=ath11k-bringup&id=3a7b4838b6f6f234239f263ef3dc02e612a083ad.

The patch is for AHB devices such as IPQ8074, it has remote proc module
which is used to download the firmware and boots the processor which
firmware is running on. If firmware crashed, remote proc module will
detect it and download and boot firmware again. Below command will
trigger a firmware crash, and then user can test feature of device
recovery.

Test command:
echo assert > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash
echo assert > /sys/kernel/debug/ath11k/wcn6855\ hw2.0/simulate_fw_crash

Unfortunately, QCA6390 is PCIe bus, it does not have the remote proc
module, it use mhi module to communicate between firmware and ath11k.
So ath11k does not support device recovery for QCA6390 currently.

This patch is to add the extra logic which is different for QCA6390.
When firmware crashed, MHI_CB_EE_RDDM event will be indicate by
firmware and then ath11k_mhi_op_status_cb which is the callback of
mhi_controller will receive the MHI_CB_EE_RDDM event, then ath11k
will start to do recovery process, ath11k_core_reset() calls
ath11k_hif_power_down()/ath11k_hif_power_up(), then the mhi/ath11k
will start to download and boot firmware. There are some logic to
avoid deadloop recovery and two simultaneous recovery operations.
And because it has muti-radios for the soc, so it add some logic
in ath11k_mac_op_reconfig_complete() to make sure all radios has
reconfig complete and then complete the device recovery.

Also it add workqueue_aux, because ab->workqueue is used when receive
ATH11K_QMI_EVENT_FW_READY in recovery process(queue_work(ab->workqueue,
&ab->restart_work)), and ath11k_core_reset will wait for max
ATH11K_RESET_TIMEOUT_HZ for the previous restart_work finished, if
ath11k_core_reset also queued in ab->workqueue, then it will delay
restart_work of previous recovery and lead previous recovery fail.

ath11k recovery success for QCA6390/WCN6855 after apply this patch.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-2-quic_wgong@quicinc.com

ath11k: disable regdb support for QCA6390

Currently it does not have regdb files for QCA6390, so disable its regdb
support feature now.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220319023543.14288-3-quic_wgong@quicinc.com

ath11k: Add basic WoW functionalities

Implement basic WoW functionalities such as magic-packet, disconnect
and pattern. The logic is very similar to ath10k.

When WoW is configured, ath11k_core_suspend and ath11k_core_resume
are skipped as WoW configuration and hif suspend/resume are done in
ath11k_wow_op_suspend() and ath11k_wow_op_resume().

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-2-git-send-email-quic_cjhuang@quicinc.com

ath11k: reduce the wait time of 11d scan and hw scan while add interface

(cherry picked from commit 1f682dc9fb3790aa7ec27d3d122ff32b1eda1365 in wireless-next)

Currently ath11k will wait 11d scan complete while add interface in
ath11k_mac_op_add_interface(), when system resume without enable
wowlan, ath11k_mac_op_add_interface() is called for each resume, thus
it increase the resume time of system. And ath11k_mac_op_hw_scan()
after ath11k_mac_op_add_interface() also needs some time cost because
the previous 11d scan need more than 5 seconds when 6 GHz is enabled,
then the scan started event will indicated to ath11k after the 11d
scan completed.

While 11d scan/hw scan is running in firmware, if ath11k update channel
list to firmware by WMI_SCAN_CHAN_LIST_CMDID, then firmware will cancel
the current scan which is running, it lead the scan failed. The patch
commit 9dcf6808b253 ("ath11k: add 11d scan offload support") used
finish_11d_scan/finish_11d_ch_list/pending_11d to synchronize the 11d
scan/hw scan/channel list between ath11k/firmware/mac80211 and to avoid
the scan fail.

Add wait operation before ath11k update channel list, function
ath11k_reg_update_chan_list() will wait until the current 11d scan/hw
scan completed. And remove the wait operation of start 11d scan and
waiting channel list complete in hw scan. After these changes, resume
time cost reduce about 5 seconds and also hw scan time cost reduced
obviously, and scan failed not seen.

The 11d scan is sent to firmware only one time for each interface added
in mac.c, and it is moved after the 1st hw scan because 11d scan will
cost some time and thus leads the AP scan result update to UI delay.
Currently priority of ath11k's hw scan is WMI_SCAN_PRIORITY_LOW, and
priority of 11d scan in firmware is WMI_SCAN_PRIORITY_MEDIUM, then the
11d scan which sent after hw scan will cancel the hw scan in firmware,
so change the priority to WMI_SCAN_PRIORITY_MEDIUM for the hw scan which
is in front of the 11d scan, thus it will not happen scan cancel in
firmware.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Fixes: 9dcf6808b253 ("ath11k: add 11d scan offload support")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215777
Cc: <stable@vger.kernel.org>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328035832.14122-1-quic_wgong@quicinc.com
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220427111619.9758-1-kvalo@kernel.org

ath11k: remove unneeded flush_workqueue

All work currently pending will be done first by calling destroy_workqueue,
so there is no need to flush it explicitly.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi (CGEL ZTE) <lv.ruyi@zte.com.cn>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220301013246.2052570-1-lv.ruyi@zte.com.cn

ath11k: add dbring debug support

Target copies spectral report and CFR report through dbring to
host for further processing. This mechanism involves ring and
buffer management in the Host, FW, and uCode, where improper
tail pointer update issues are seen.

This dbring debug support help to debug such issues by tracking
head and tail pointer movement along with the timestamp at which
each buffer is received and replenished.

Provide a debugfs interface to enalbe/disable dbring debug
support and dump the dbring debug entries.

Also introduced a new hardware param to add dbring debugfs support
for few hardwares which are using dbings.

Usage:

echo <dbr_id> <val> > /sys/kernel/debug/ath11k/ipq8074_2/
mac0/enable_dbr_debug

dbr_id: 0 for spectral and 1 for CFR
val: 0 - disable, 1 - enable.

Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1

Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1645366059-11798-1-git-send-email-quic_vnaralas@quicinc.com

ath11k: avoid firmware crash when reg set for QCA6390/WCN6855

For the NL80211_REGDOM_SET_BY_USER hint from cfg80211, it set the new
alpha2 code to ath11k, then ath11k send WMI_SET_INIT_COUNTRY_CMDID to
firmware for all chips currently. When test with WCN6855/QCA6390 chips,
this WMI CMD leads firmware crash.

For AP based chips(ipq8074/qcn9074), WMI_SET_INIT_COUNTRY_CMDID is used
to send to firmware, for STATION based chips(WCN6855/QCA6390), it need to
use another WMI CMD WMI_SET_CURRENT_COUNTRY_CMDID.

Add flag current_cc_support in hardware parameters, it is used to
distinguish AP/STA platform. After that, the firmware will work
normal and the regulatory feature works well for QCA6390/WCN6855.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220119041355.32014-1-quic_wgong@quicinc.com

ath11k: fix workqueue not getting destroyed after rmmod

Currently, ath11k_core_alloc() creates a single thread workqueue.
This workqueue is not detroyed during clean up when ath11k modules
are unloaded from the kernel and is left as it is.
If workqueue is not destroyed, it could lead to kernel
memory scarcity in a longer run. This could affect self and
other drivers workability as well.

Add destroy workqueue in ath11k_core_free().

Tested on: IPQ8074 WLAN.HK.2.4.0.1-01746-QCAHKSWPL_SILICONZ-1

Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1640231787-17408-1-git-send-email-quic_adisi@quicinc.com

ath11k: add support of firmware logging for WCN6855

Host enables WMI firmware logging feature via QMI message.
Host receives firmware logging messages on WMI_DIAG_EVENTID, then
sends logging messages to user space via event tracing infrastructure.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Cheng Wang <quic_chengwan@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211220121053.357087-1-quic_chengwan@quicinc.com

ath11k: add regdb.bin download for regdb offload

The regdomain is self-managed type for ath11k, the regdomain info is
reported from firmware, it is not from wireless regdb. Firmware fetch
the regdomain info from board data file before. Currently most of the
regdomain info has moved to another file regdb.bin from board data
file for some chips such as QCA6390 and WCN6855, so the regdomain info
left in board data file is not enough to support the feature which need
more regdomain info.

After download regdb.bin, firmware will fetch the regdomain info from
regdb.bin instead of board data file and report to ath11k. If it does
not have the file regdb.bin, it also can initialize wlan success and
firmware then fetch regdomain info from board data file.

Add download the regdb.bin before download board data for some specific
chip which support supports_regdb in hardware parameters.

download regdb.bin log:
[430082.334162] ath11k_pci 0000:05:00.0: chip_id 0x2 chip_family 0xb board_id 0x106 soc_id 0x400c0200
[430082.334169] ath11k_pci 0000:05:00.0: fw_version 0x110c8b4c fw_build_timestamp 2021-10-25 07:41 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02892-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
[430082.334414] ath11k_pci 0000:05:00.0: boot firmware request ath11k/WCN6855/hw2.0/regdb.bin size 24310

output of "iw reg get"
global
country US: DFS-FCC
(2402 - 2472 @ 40), (N/A, 30), (N/A)
(5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
(5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
(5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
(5735 - 5835 @ 80), (N/A, 30), (N/A)
(57240 - 63720 @ 2160), (N/A, 40), (N/A)

phy#0 (self-managed)
country US: DFS-FCC
(2402 - 2472 @ 40), (6, 30), (N/A)
(5170 - 5250 @ 80), (N/A, 24), (N/A), AUTO-BW
(5250 - 5330 @ 80), (N/A, 24), (0 ms), DFS, AUTO-BW
(5490 - 5730 @ 160), (N/A, 24), (0 ms), DFS, AUTO-BW
(5735 - 5895 @ 160), (N/A, 30), (N/A), AUTO-BW
(5945 - 7125 @ 160), (N/A, 24), (N/A), NO-OUTDOOR, AUTO-BW

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211220062355.17021-1-quic_wgong@quicinc.com

ath11k: add support for hardware rfkill for QCA6390

When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath11k will check the capability, and if it is enabled then
ath11k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath11k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware and also notifies cfg80211.

This only enable rfkill feature for QCA6390, rfkill_pin is all initialized to 0
for other chips in ath11k_hw_params.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211217102334.14907-1-quic_wgong@quicinc.com

ath11k: report rssi of each chain to mac80211 for QCA6390/WCN6855

Command "iw wls1 station dump" does not show each chain's rssi currently.

If the rssi of each chain from mon status which parsed in function
ath11k_hal_rx_parse_mon_status_tlv() is invalid, then ath11k send
wmi cmd WMI_REQUEST_STATS_CMDID with flag WMI_REQUEST_RSSI_PER_CHAIN_STAT
to firmware, and parse the rssi of chain in wmi WMI_UPDATE_STATS_EVENTID,
then report them to mac80211.

WMI_REQUEST_STATS_CMDID is only sent when CONFIG_ATH11K_DEBUGFS is set,
it is only called by ath11k_mac_op_sta_statistics(). It does not effect
performance and power consumption. Because after STATION connected to
AP, it is only called every 6 seconds by NetworkManager in below stack.

[ 797.005587] CPU: 0 PID: 701 Comm: NetworkManager Tainted: G W OE 5.13.0-rc6-wt-ath+ #2
[ 797.005596] Hardware name: LENOVO 418065C/418065C, BIOS 83ET63WW (1.33 ) 07/29/2011
[ 797.005600] RIP: 0010:ath11k_mac_op_sta_statistics+0x2f/0x1b0 [ath11k]
[ 797.005644] Code: 41 56 41 55 4c 8d aa 58 01 00 00 41 54 55 48 89 d5 53 48 8b 82 58 01 00 00 48 89 cb 4c 8b 70 20 49 8b 06 4c 8b a0 90 08 00 00 <0f> 0b 48 8b 82 b8 01 00 00 48 ba 00 00 00 00 01 00 00 00 48 89 81
[ 797.005651] RSP: 0018:ffffb1fc80a4b890 EFLAGS: 00010282
[ 797.005658] RAX: ffff8a5726200000 RBX: ffffb1fc80a4b958 RCX: ffffb1fc80a4b958
[ 797.005664] RDX: ffff8a5726a609f0 RSI: ffff8a581247f598 RDI: ffff8a5702878800
[ 797.005668] RBP: ffff8a5726a609f0 R08: 0000000000000000 R09: 0000000000000000
[ 797.005672] R10: 0000000000000000 R11: 0000000000000007 R12: 02dd68024f75f480
[ 797.005676] R13: ffff8a5726a60b48 R14: ffff8a5702879f40 R15: ffff8a5726a60000
[ 797.005681] FS: 00007f632c52a380(0000) GS:ffff8a583a200000(0000) knlGS:0000000000000000
[ 797.005687] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 797.005692] CR2: 00007fb025d69000 CR3: 00000001124f6005 CR4: 00000000000606f0
[ 797.005698] Call Trace:
[ 797.005710] sta_set_sinfo+0xa7/0xb80 [mac80211]
[ 797.005820] ieee80211_get_station+0x50/0x70 [mac80211]
[ 797.005925] nl80211_get_station+0xd1/0x200 [cfg80211]
[ 797.006045] genl_family_rcv_msg_doit.isra.15+0x111/0x140
[ 797.006059] genl_rcv_msg+0xe6/0x1e0
[ 797.006065] ? nl80211_dump_station+0x220/0x220 [cfg80211]
[ 797.006223] ? nl80211_send_station.isra.72+0xf50/0xf50 [cfg80211]
[ 797.006348] ? genl_family_rcv_msg_doit.isra.15+0x140/0x140
[ 797.006355] netlink_rcv_skb+0xb9/0xf0
[ 797.006363] genl_rcv+0x24/0x40
[ 797.006369] netlink_unicast+0x18e/0x290
[ 797.006375] netlink_sendmsg+0x30f/0x450
[ 797.006382] sock_sendmsg+0x5b/0x60
[ 797.006393] ____sys_sendmsg+0x219/0x240
[ 797.006403] ? copy_msghdr_from_user+0x5c/0x90
[ 797.006413] ? ____sys_recvmsg+0xf5/0x190
[ 797.006422] ___sys_sendmsg+0x88/0xd0
[ 797.006432] ? copy_msghdr_from_user+0x5c/0x90
[ 797.006443] ? ___sys_recvmsg+0x9e/0xd0
[ 797.006454] ? __fget_files+0x58/0x90
[ 797.006461] ? __fget_light+0x2d/0x70
[ 797.006466] ? do_epoll_wait+0xce/0x720
[ 797.006476] ? __sys_sendmsg+0x63/0xa0
[ 797.006485] __sys_sendmsg+0x63/0xa0
[ 797.006497] do_syscall_64+0x3c/0xb0
[ 797.006509] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 797.006519] RIP: 0033:0x7f632d99912d
[ 797.006526] Code: 28 89 54 24 1c 48 89 74 24 10 89 7c 24 08 e8 ca ee ff ff 8b 54 24 1c 48 8b 74 24 10 41 89 c0 8b 7c 24 08 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 2f 44 89 c7 48 89 44 24 08 e8 fe ee ff ff 48
[ 797.006533] RSP: 002b:00007ffd80808c00 EFLAGS: 00000293 ORIG_RAX: 000000000000002e
[ 797.006540] RAX: ffffffffffffffda RBX: 0000563dab99d840 RCX: 00007f632d99912d
[ 797.006545] RDX: 0000000000000000 RSI: 00007ffd80808c50 RDI: 000000000000000b
[ 797.006549] RBP: 00007ffd80808c50 R08: 0000000000000000 R09: 0000000000001000
[ 797.006552] R10: 0000563dab96f010 R11: 0000000000000293 R12: 0000563dab99d840
[ 797.006556] R13: 0000563dabbb28c0 R14: 00007f632dad4280 R15: 0000563dabab11c0
[ 797.006563] ---[ end trace c9dcf08920c9945c ]---

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211215090944.19729-1-quic_wgong@quicinc.com

ath11k: Change qcn9074 fw to operate in mode-2

In mode-2 QCN9074 firmware uses 15MB of host memory and firmware
request 1MB size segements in QMI, whereas in mode-0 firmware
uses 45MB of host memory and each segment is of 2MB size.
In mode-2 firmware operates with reduced number of vdevs and peers.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1

Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211209104351.9811-3-kvalo@kernel.org

ath11k: add ab to TARGET_NUM_VDEVS & co

The next patch changes TARGET_NUM_VDEVS to be dynamic and need access to ab.
Add ab separately to keep the next patch simple.

Compile tested only.

Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211209104351.9811-2-kvalo@kernel.org

ath11k: Add htt cmd to enable full monitor mode

A new hw_param full_monitor_mode is added to enable full
monitor support for QCN9074.
HTT_H2T_MSG_TYPE_RX_FULL_MONITOR_MODE cmd is sent to FW
to enable the full monitor mode.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-2-git-send-email-akolli@codeaurora.org

ath11k: add wait operation for tx management packets for flush from mac80211

In ath11k, tx of management packet is doing in a work queue. Sometimes
the workqueue does not finish tx immediately, then it lead after the next
step of vdev delete finished, it start to send the management packet to
firmware and lead firmware crash.

ieee80211_set_disassoc() have logic of ieee80211_flush_queues() after
it send_deauth_disassoc() to ath11k, its purpose is make sure the
deauth was actually sent, so it need to change ath11k to match the
purpose of mac80211.

To address these issue wait for tx mgmt as well as tx data packets.

dmesg log of connect/disconnect to AP:
[ 307.522226] wls1: authenticate with 62:66:e4:e9:6a:a9
[ 307.586565] wls1: send auth to 62:66:e4:e9:6a:a9 (try 1/3)
[ 307.586581] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 307.586922] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 307.590179] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 307.590181] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 307.598699] wls1: authenticated
[ 307.599483] wls1: associate with 62:66:e4:e9:6a:a9 (try 1/3)
[ 307.599506] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 307.599519] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 307.603059] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 307.603063] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 307.637105] wls1: associated
[ 317.365239] wls1: deauthenticating from 62:66:e4:e9:6a:a9 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 317.368104] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 317.372622] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 317.378320] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 317.378330] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 317.378359] ath11k_pci 0000:05:00.0: mac mgmt tx flush mgmt pending 0
[ 317.421066] ath11k_pci 0000:05:00.0: mac mgmt tx flush mgmt pending 0
[ 317.421427] ath11k_pci 0000:05:00.0: mac remove interface (vdev 0)

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211202063705.14321-1-quic_wgong@quicinc.com

ath11k: add 11d scan offload support

Add handler for WMI_11D_NEW_COUNTRY_EVENTID, WMI_11D_SCAN_START_CMDID,
WMI_11D_SCAN_STOP_CMDID.

After vdev create for STATION, send WMI_11D_SCAN_START_CMDID to firmware
and wait firmware complete it, the scan from mac80211 also need to wait
the 11d scan finished, and send WMI_11D_SCAN_STOP_CMDID to firmware
before vdev delete for STATION.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211201071745.17746-4-quic_wgong@quicinc.com

ath11k: add support for WCN6855 hw2.1

Ath11k fails to probe WCN6855 hw2.1 chip:

[ 6.983821] ath11k_pci 0000:06:00.0: enabling device (0000 -> 0002)
[ 6.983841] ath11k_pci 0000:06:00.0: Unsupported WCN6855 SOC hardware version: 18 17

This is caused by the wrong bit mask setting of hardware major version:
for QCA6390/QCN6855, it should be BIT8-11, not BIT8-16, so change the
definition to GENMASK(11, 8).

Also, add a separate entry for WCN6855 hw2.1 in ath11k_hw_params.

Please note that currently WCN6855 hw2.1 shares the same firmwares
as hw2.0, so users of this chip need to create a symlink as below:

ln -s hw2.0 hw2.1

Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Fixes: 18ac1665e785 ("ath11k: pci: check TCSR_SOC_HW_VERSION")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129025613.21594-1-quic_bqiang@quicinc.com

Revert "ath11k: add read variant from SMBIOS for download board data"

This reverts commit 46e46db313a2bf3c48cac4eb8bdb613b762f301b. Mark reported
that it breaks QCA6390 hw2.0 on Dell XPS 13 9310:

[    5.537034] ath11k_pci 0000:72:00.0: chip_id 0x0 chip_family 0xb board_id 0xff soc_id 0xffffffff
[    5.537038] ath11k_pci 0000:72:00.0: fw_version 0x101c06cc fw_build_timestamp 2020-06-24 19:50 fw_build_id
[    5.537236] ath11k_pci 0000:72:00.0: failed to fetch board data for bus=pci,qmi-chip-id=0,qmi-board-id=255,variant=DE_1901 from ath11k/QCA6390/hw2.0/board-2.bin
[    5.537255] ath11k_pci 0000:72:00.0: failed to fetch board-2.bin or board.bin from QCA6390/hw2.0
[    5.537257] ath11k_pci 0000:72:00.0: qmi failed to fetch board file: -2
[    5.537258] ath11k_pci 0000:72:00.0: failed to load board data file: -2

So we need to back to the drawing board and implement it so that backwards
compatiblity is not broken.

Reported-by: Mark Herbert <mark.herbert42@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211124094316.9096-1-kvalo@codeaurora.org

ath11k: add read variant from SMBIOS for download board data

This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118100033.8384-1-quic_wgong@quicinc.com

ath11k: add hw_param for wakeup_mhi

Wakeup mhi is needed before pci_read/write only for QCA6390 and WCN6855. Since
wakeup & release mhi is enabled for all hardwares, below mhi assert is seen in
QCN9074 when doing 'rmmod ath11k_pci':

Kernel panic - not syncing: dev_wake != 0
CPU: 2 PID: 13535 Comm: procd Not tainted 4.4.60 #1
Hardware name: Generic DT based system
[<80316dac>] (unwind_backtrace) from [<80313700>] (show_stack+0x10/0x14)
[<80313700>] (show_stack) from [<805135dc>] (dump_stack+0x7c/0x9c)
[<805135dc>] (dump_stack) from [<8032136c>] (panic+0x84/0x1f8)
[<8032136c>] (panic) from [<80549b24>] (mhi_pm_disable_transition+0x3b8/0x5b8)
[<80549b24>] (mhi_pm_disable_transition) from [<80549ddc>] (mhi_power_down+0xb8/0x100)
[<80549ddc>] (mhi_power_down) from [<7f5242b0>] (ath11k_mhi_op_status_cb+0x284/0x3ac [ath11k_pci])
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[<7f5242b0>] (ath11k_mhi_op_status_cb [ath11k_pci]) from [<7f524878>] (ath11k_mhi_stop+0x10/0x20 [ath11k_pci])
[<7f524878>] (ath11k_mhi_stop [ath11k_pci]) from [<7f525b94>] (ath11k_pci_power_down+0x54/0x90 [ath11k_pci])
[<7f525b94>] (ath11k_pci_power_down [ath11k_pci]) from [<8056b2a8>] (pci_device_shutdown+0x30/0x44)
[<8056b2a8>] (pci_device_shutdown) from [<805cfa0c>] (device_shutdown+0x124/0x174)
[<805cfa0c>] (device_shutdown) from [<8033aaa4>] (kernel_restart+0xc/0x50)
[<8033aaa4>] (kernel_restart) from [<8033ada8>] (SyS_reboot+0x178/0x1ec)
[<8033ada8>] (SyS_reboot) from [<80301b80>] (ret_fast_syscall+0x0/0x34)

Hence, disable wakeup/release mhi using hw_param for other hardwares.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01060-QCAHKSWPL_SILICONZ-1

Fixes: a05bd8513335 ("ath11k: read and write registers below unwindowed address")
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636702019-26142-1-git-send-email-quic_seevalam@quicinc.com

ath11k: add string type to search board data in board-2.bin for WCN6855

Currently ath11k only support string type with bus, chip id and board id
such as "bus=ahb,qmi-chip-id=1,qmi-board-id=4" for ahb bus chip and
"bus=pci,qmi-chip-id=0,qmi-board-id=255" for PCIe bus chip in
board-2.bin. For WCN6855, it is not enough to distinguish all different
chips.

This is to add a new string type which include bus, chip id, board id,
vendor, device, subsystem-vendor and subsystem-device for WCN6855.

ath11k will first load board-2.bin and search in it for the board data
with the above parameters, if matched one board data, then download it
to firmware, if not matched any one, then ath11k will download the file
board.bin to firmware.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111065340.20187-1-quic_wgong@quicinc.com

ath11k: Disabling credit flow for WMI path

Firmware credit flow control is enabled for WMI control services,
which expects available tokens should be acquired before sending a
command to the target. Also the token gets released when firmware
receives the command.

This credit-based flow limits driver to send WMI command only
when the token available which is causing WMI commands to timeout and
return -EAGAIN, whereas firmware has enough capability to process the
WMI command. To fix this Tx starvation issue, introduce the ability to
disable the credit flow for the WMI path.

The driver sends WMI configuration for disabling credit flow to firmware
by two ways.
1. By using a global flag
(HTC_MSG_SETUP_COMPLETE_EX_ID msg type flags)
2. By using a local flag
(ATH11K_HTC_CONN_FLAGS_DISABLE_CREDIT_FLOW_CTRL = 1 << 3)

Ath11k uses both these configurations to disable credit flow for the
WMI path completely.

Also added a hw_param member for credit flow control by which we can
enable or disable it based on per-target basis. Currently we are disabling
credit flow for IPQ8074, IPQ6018, and QCN9074 as recommended by firmware.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1

Co-developed-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635156494-20059-1-git-send-email-quic_ppranees@quicinc.com

ath11k: allocate dst ring descriptors from cacheable memory

tcl_data and reo_dst rings are currently being allocated using
dma_allocate_coherent() which is non cacheable.

Allocating ring memory from cacheable memory area allows cached descriptor
access and prefetch next descriptors to optimize CPU usage during
descriptor processing on NAPI. Based on the hardware param we can enable
or disable this feature for the corresponding platform.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1

Co-developed-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-3-git-send-email-ppranees@codeaurora.org

ath11k: enable 802.11 power save mode in station mode

To reduce power consumption enable 802.11 power save mode in station mode. This
allows both radio and CPU to sleep more.

Only enable the mode on QCA6390 and WCN6855, it's unknown how other hardware
families support this feature.

To test that power save mode is running run "iw dev wls1 set power_save off",
check there is no NULL Data frame seen by a sniffer. And run "iw dev wls1 set power_save
on" and check there is a NULL Data frame in sniffer.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211108123826.8463-2-kvalo@codeaurora.org

ath11k: set correct NL80211_FEATURE_DYNAMIC_SMPS for WCN6855

Commit 6f4d70308e5e ("ath11k: support SMPS configuration for 6 GHz") changed
"if (ht_cap & WMI_HT_CAP_DYNAMIC_SMPS)" to "if (ht_cap &
WMI_HT_CAP_DYNAMIC_SMPS || ar->supports_6ghz)" which means
NL80211_FEATURE_DYNAMIC_SMPS is enabled for all chips which support 6 GHz.
However, WCN6855 supports 6 GHz but it does not support feature
NL80211_FEATURE_DYNAMIC_SMPS, and this can lead to MU-MIMO test failures for
WCN6855.

Disable NL80211_FEATURE_DYNAMIC_SMPS for WCN6855 since its ht_cap does not
support WMI_HT_CAP_DYNAMIC_SMPS. Enable the feature only on QCN9074 as that's
the only other device supporting 6 GHz band.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-3-jouni@codeaurora.org

ath11k: change return buffer manager for QCA6390

QCA6390 firmware uses HAL_RX_BUF_RBM_SW1_BM, not HAL_RX_BUF_RBM_SW3_BM. This is
needed to fix a case where an A-MSDU has an unexpected LLC/SNAP header in the
first subframe (CVE-2020-24588).

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-2-jouni@codeaurora.org

ath11k: Change number of TCL rings to one for QCA6390

Some targets, QCA6390 for example, use only one TCL ring, it is better to
initialize only one ring and leave others untouched for such targets.

This is a theoretical fix found during code review, no visible impact.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-1-jouni@codeaurora.org

ath11k: use hw_params to access board_size and cal_offset

Reuse board_size from hw_params, add cal_offset to hw params.
This patch is clean up only, there is no change in functionality.

cal_size was unused, so remove that.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-2-jouni@codeaurora.org

ath11k: Add spectral scan support for QCN9074

Populate the below hw parameters as per the QCN9074 support
1. FFT bin size as two bytes
2. Maximum FFT bin count as 1024
3. Summary report pad size as 16
4. FFT report header length as 24

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-5-jouni@codeaurora.org

ath11k: Introduce spectral hw configurable param

Below parameters have been identified as configurable across the platforms.
So to scale the spectral across the platforms, move these parameter
into hw param.

1. Maximum FFT bins
2. Summary report pad size
3. FFT report header length

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-3-jouni@codeaurora.org

ath11k: Refactor spectral FFT bin size

In IPQ8074, actual FFT bin size is two bytes but hardware reports it
with extra pad size of two bytes for each FFT bin. So finally each FFT
bin advertise as four bytes size in the collected data. This FFT pad is
not advertised in IPQ6018 platform. To accommodate this different
behavior across the platforms, introduce the hw param fft_pad_sz and use
it in spectral process. Also group all the spectral params under the new
structure in hw param structure for scalable in future.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-2-jouni@codeaurora.org

ath11k: Fix an error handling path in ath11k_core_fetch_board_data_api_n()

All error paths but this one 'goto err' in order to release some
resources.
Fix this.

Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/e959eb544f3cb04258507d8e25a6f12eab126bde.1621676864.git.christophe.jaillet@wanadoo.fr

ath11k: don't call ath11k_pci_set_l1ss for WCN6855

For QCA6390, one PCI related clock drifts sometimes, and it makes
PCI link difficult to quit L1ss. Current implementation fixed this
by configuring some related regs using ath11k_pci_fix_l1ss.

WCN6855 does not have this clock drift problem, so no need to set
these regs.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-8-jouni@codeaurora.org

ath11k: add support for WCN6855

This patch is to add support for WCN6855. For station mode,
WCN6855 is able to connect to an AP, and ping works well.
For AP mode, hostapd is able to bringup an SAP interface with
WCN6855, a normal station can connect to this AP and
ping works well.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-7-jouni@codeaurora.org

ath11k: print hardware name and version during initialisation

This way it's easy for the user to find what device is actually installed. This
also helps reporting bugs.

Screenshot:

[ 459.988812] ath11k_pci 0000:06:00.0: BAR 0: assigned [mem 0xdb000000-0xdbffffff 64bit]
[ 459.988867] ath11k_pci 0000:06:00.0: enabling device (0000 -> 0002)
[ 459.997048] ath11k_pci 0000:06:00.0: qca6390 hw2.0
[ 460.058093] mhi mhi0: Requested to power ON
[ 460.059741] mhi mhi0: Power on setup success
[ 460.476924] ath11k_pci 0000:06:00.0: chip_id 0x0 chip_family 0xb board_id 0xff soc_id 0xffffffff
[ 460.477032] ath11k_pci 0000:06:00.0: fw_version 0x101c06cc fw_build_timestamp 2020-06-24 19:50 fw_build_id

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1613589400-18891-1-git-send-email-kvalo@codeaurora.org

ath11k: add extended interrupt support for QCN9074

Update the specific hw ring mask for QCN9074. Update the timestamp
information while processing DP and CE interrupts.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-11-git-send-email-akolli@codeaurora.org

ath11k: add CE interrupt support for QCN9074

Define host CE configuration for QCN9074 since the max CE count is six.
Available MSI interrupt is five so cannot able to map the ce_id directly
for the msi_data_idx. Added get_ce_msi_idx ops in ath11k_hif_ops to get
the CE MSI idx which is used to initialize the CE ring.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-10-git-send-email-akolli@codeaurora.org

ath11k: add data path support for QCN9074

hal rx descriptor is different for QCN9074 target type. since
rx_msdu_end, rx_msdu_start, rx_mpdu_start elements are in
different placement/alignment. In order to have generic data path,
introduce platform specific hal rx descriptor access ops in
ath11k_hw_ops.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-9-git-send-email-akolli@codeaurora.org

ath11k: add hal support for QCN9074

Define the hal ring address and ring meta descriptor mask for
QCN9074. Move the platform specific address to the ath11k_hw_regs.
Define tx_mesh_enable ops in ath11k_hw_ops since its accessing
platform specific TCL descriptor.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-8-git-send-email-akolli@codeaurora.org

ath11k: Add qcn9074 mhi controller config

Add MHI config for QCN9074 also populate ath11k_hw_params for QCN9074.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-6-git-send-email-akolli@codeaurora.org

ath11k: Move qmi service_ins_id to hw_params

qmi service_ins_id is unique for QCA6390 and QCN9074,
this is needed for adding QCN9074 support. No functional
changes.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-3-git-send-email-akolli@codeaurora.org

ath11k: Fix error code in ath11k_core_suspend()

The "if (!ret)" condition is inverted and it should be "if (ret)". It means
that we return success when we had intended to return an error code. This also
caused a spurious warning even when the suspend was successful:

[ 297.186612] ath11k_pci 0000:06:00.0: failed to suspend hif: 0

Fixes: d1b0c33850d2 ("ath11k: implement suspend for QCA6390 PCI devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X9nF17L2/EKOSbn/@mwanda

ath11k: implement suspend for QCA6390 PCI devices

Now that all the needed pieces are in place implement suspend support QCA6390
PCI devices. All other devices will return -EOPNOTSUPP during suspend. The
suspend is implemented by switching the firmware to WoW mode during suspend, so
the firmware will be running on low power mode while host is in suspend.

At the moment we are not able to shutdown and fully power off the device due to
bugs in MHI subsystem, so WoW mode is a workaround for the time being.

During suspend we enable WoW mode, disable CE irq and DP irq, then put MHI to
suspend state. During resume, driver resumes MHI firstly, then enables CE irq
and dp IRQ, and sends WoW wakeup command to firmware.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-11-git-send-email-kvalo@codeaurora.org

ath11k: implement WoW enable and wakeup commands

Implement wow enable ane wow wakeup commands which are needed for suspend.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-9-git-send-email-kvalo@codeaurora.org

ath11k: htc: implement suspend handling

When ath11k sends suspend command to firmware, firmware will
return suspend_complete events and add handlers for those.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-6-git-send-email-kvalo@codeaurora.org

ath11k: put hw to DBS using WMI_PDEV_SET_HW_MODE_CMDID

It's recommended to use wmi command WMI_PDEV_SET_HW_MODE_CMDID to put hardware
to dbs mode instead of wmi_init command. This fixes a few strange stability
issues.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-3-git-send-email-kvalo@codeaurora.org

ath11k: peer delete synchronization with firmware

Peer creation in firmware fails, if last peer deletion
is still in progress.
Hence, add wait for the event after deleting every peer
from host driver to synchronize with firmware.

Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-3-git-send-email-mkenna@codeaurora.org

ath11k: vdev delete synchronization with firmware

When the interface is added immediately after removing the
interface, vdev deletion in firmware might not have been
completed.

Hence, add vdev_delete_resp_event and wait_event_timeout
to synchronize with firmware.

Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-2-git-send-email-mkenna@codeaurora.org

ath11k: cold boot calibration support

cold boot calibration is the process to calibrate all the channels
during the boot-up to avoid the calibration delay during the
channel change.
During the boot-up, firmware started in cold boot calibration mode
Firmware calibrate all channels and generate CalDb(DDR).
Subsequent wifi bringup will reuse the same CalDb.
Firmware is restarted in normal mode to continue the normal operation.

caldb memory address send to firmware through the QMI message.Firmware
use this address to store the caldb data and use it until next reboot.

This will give the improvement during the channel change. But it is
increasing the boot-up time(up to 15sec depend on number of radios).
So if the user want to reduce the boot-up time and accepting for channel
change delay, user can disable this feature using the module param
cold_boot_cal=0.

Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01162-QCAHKSWPL_SILICONZ-1

Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602862111-14063-1-git-send-email-ssreeela@codeaurora.org

ath11k: search DT for qcom,ath11k-calibration-variant

Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on IPQ6018 using bus, qmi-chip-id and
qmi-board-id.

The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.

This problem was already solved on ath10k by adding a ",variant=.*" at the
end of the board name. The same functionality must also be provided for
ath11k.

The device tree requires an additional string to define the variant name

wifi@c000000 {
status = "okay";
qcom,ath11k-calibration-variant = "Cigtech-WF-188";
};

This would create the boarddata identifier for the board-2.bin search

* bus=ahb,qmi-chip-id=0,qmi-board-id=18,variant=Cigtech-WF-188

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-2-sven@narfation.org

ath11k: enable idle power save mode

Host sends wmi command to allow hardware enter idle power
save mode in ath11k_mac_op_start function.

hw parameter idle_ps indicates whether idle power save is supported.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-8-git-send-email-kvalo@codeaurora.org

ath11k: enable shadow register configuration and access

To enable shadow register access, host needs to pass shadow
register configuration to firmware via qmi message. Host also
needs to update ring's HP or TP address to shadow register
address. The write operation to shadow register will be
forwarded to target register by hardware automatically, and
the write operation to shadow register is permitted even
when the target is in power save or sleep mode.

Update the shadow config whenever power up happens.

This feature is controlled by hw parameter supports_shadow_regs which is only
enabled for QCA6390.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-3-git-send-email-kvalo@codeaurora.org

ath11k: disable monitor mode on QCA6390

QCA6390 does not support monitor mode at the moment so disable it altogether,
using a hack as mac80211 does not support disabling it otherwise. Add a boolean
to hw_params to know if hardware supports monitor mode.

IPQ8074 continues to support monitor mode normally.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-6-git-send-email-kvalo@codeaurora.org

ath11k: add interface_modes to hw_params

As QCA6390 does not support mesh interfaces, move the interface_modes to
hw_params. Also create interface combinations dynamically so that it's easy to
change the values.

Now QCA6390 does not claim to support mesh interfaces to user space, but
IPQ8074 continues to do that.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-4-git-send-email-kvalo@codeaurora.org

ath11k: Add support spectral scan for IPQ6018

IPQ6018 supported with 4 bytes FFT BIN size. so supported 4 bytes
parsing logic in FFT report process. since spectral_fft_sz is
configured as zero in hw_params, spectral is not supported in
QCA6390 platform.

Tested-on: IPQ6018 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600236776-4042-1-git-send-email-periyasa@codeaurora.org

ath11k: debugfs: use ath11k_debugfs_ prefix

As these functions are now defined in debugfs.c change the prefix to use
ath11k_debugfs_ as well.

No functional changes. Compile tested only.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600264523-12939-2-git-send-email-kvalo@codeaurora.org

ath11k: Remove rproc references from common core layer

IPQ8074 HW uses rproc with AHB as underlying hif layer.
Move rproc references from common core layer to target
hif layer. Remove IS_ENABLED check for CONFIG_REMOTEPROC
as it's not required anymore.

No functional changes. Compile tested only.

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600090615-18904-1-git-send-email-govinds@codeaurora.org

ath11k: fix link error when CONFIG_REMOTEPROC is disabled

If CONFIG_REMOTEPROC was disabled the linking failed with:

ERROR: modpost: "rproc_get_by_phandle" [drivers/net/wireless/ath/ath11k/ath11k.ko] undefined!

Compile tested only.

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 1ff8ed786d5d ("ath11k: use remoteproc only with AHB devices")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/0101017476e38f40-c4168ac4-c00a-4220-a032-fe17e4a157cb-000000@us-west-2.amazonses.com

ath11k: remove calling ath11k_init_hw_params() second time

During probe ath11k_init_hw_params() is called from ath11k_core_pre_init()
and is not needed agian in ath11k_core_init().

Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1

Fixes: 1ff8ed786d5d (ath11k: use remoteproc only with AHB devices)
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746d2a40d3-25cd7dbe-c0dd-4fdf-8735-366d7fb40207-000000@us-west-2.amazonses.com

ath11k: add raw mode and software crypto support

Adding raw mode tx/rx support. Also, adding support
for software crypto which depends on raw mode.

To enable raw mode tx/rx:
insmod ath11k.ko frame_mode=0

To enable software crypto:
insmod ath11k.ko crypto_mode=1

These modes could be helpful in debugging crypto related issues.

Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746c6a52d9-18302a2c-0d6d-4057-aa4b-95960c809646-000000@us-west-2.amazonses.com

ath11k: add ipq6018 support

IPQ6018 has one 5G and one 2G radio with 2x2,
shares ipq8074 configurations.

Tested on: IPQ6018 hw1.0 AHB WLAN.HK.2.2-02134-QCAHKSWPL_SILICONZ-1
Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746cb68b63-c2bc31ec-a31e-442e-a572-26f4c045c06b-000000@us-west-2.amazonses.com

ath11k: move target ce configs to hw_params

Move target CE config and target CE service config to hw_params.
No functional changes.

Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746cb685d9-6bedeccb-29a1-4d32-8664-fcfe7d105f4a-000000@us-west-2.amazonses.com

ath11k: Use fallthrough pseudo-keyword

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200727194415.GA1275@embeddedor

ath11k: use TCL_DATA_RING_0 for QCA6390

For QCA6390, wbm2sw1 is used for other purpose rather than
tx completion ring. So use TCL_DATA_RING 0 only for QCA6390.

Add MISC_CAPS_TCL_0_ONLY to control it.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-9-git-send-email-kvalo@codeaurora.org

ath11k: assign correct search flag and type for QCA6390

QCA6390 doesn't enable V2 map and ummap event, so the addr search
flags and type is different from IPQ8074. Assign correct search flags
and type for QCA6390.

Without this change, ping sometimes fails. With this change, now ping
is always successful.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-7-git-send-email-kvalo@codeaurora.org

ath11k: delay vdev_start for QCA6390

For QCA6390 firmware, bss peer must be created before vdev_start, so delay
vdev_start until bss peer is created.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-6-git-send-email-kvalo@codeaurora.org

ath11k: setup QCA6390 rings for both rxdmas

For QCA6390, only one pdev is created and this pdev manages both lmacs, thus
both rxdmas. So host needs to initialize all rxdma related rings for one pdev.

Another difference is for QCA6390, host fills rxbuf to firmware and firmware
further fills the rxbuf to rxbuf ring for each rxdma.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-4-git-send-email-kvalo@codeaurora.org

ath11k: don't initialize rxdma1 related ring

For QCA6390, it has 2 lmacs and thus 2 rxdmas. However, each rxdma has rxdma0
only, and doesn't have rxdma1. So for QCA6390, don't initialize rxdma1 related
rings such as rx_mon_buf_ring, rx_mon_dst_ring and rx_mon_desc_ring.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-3-git-send-email-kvalo@codeaurora.org

ath11k: enable DP interrupt setup for QCA6390

QCA6390 uses MSI interrupt, so need to configure msi_add and
msi_data to dp srngs. As there are so many DP srngs, so need
to group them. Each group shares one MSI interrupt.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-2-git-send-email-kvalo@codeaurora.org

ath11k: wmi: put hardware to DBS mode

For QCA6390, host puts hardware to Dual Band Simultaneous (DBS) mode by default
so both 2G and 5G bands can be used. Otherwise only the 5G band can be used.
QCA6390 doesn't provide band_to_mac configuration and firmware will do the
band_to_mac map.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-12-git-send-email-kvalo@codeaurora.org

ath11k: force single pdev only for QCA6390

For QCA6390, only one pdev is created and only one HW is registered to
mac80211. This one pdev manages both 2G radio and 5G radio.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-10-git-send-email-kvalo@codeaurora.org

ath11k: ce: support different CE configurations

QCA6390 uses only 9 Copy Engines while IPQ8074 may use 12, make it possible to
change CE configuration dynamically via hw_params.

The defines for host_ce_config_wlan and CE_COUNT are temporary solutions, they
will be removed in the following patches to keep things simple.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-4-git-send-email-kvalo@codeaurora.org

ath11k: hal: create register values dynamically

QCA6390 has different register offset compared to IPQ8074, so need to
attach the register offset dynamically based on hw_params.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-2-git-send-email-kvalo@codeaurora.org

ath11k: enable internal sleep clock

On x86 and other non-qcom platforms, host needs to explicitly tell the firmware
to use the internal sleep clock. Some QCA6390 modules have OTP burnt with
external sleep clock selected, and these modules can't work expectedly unless
firmware selects internal sleep clock.

Add a field to hw_params to support this difference.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-11-git-send-email-kvalo@codeaurora.org

ath11k: add board file support for PCI devices

PCI devices like QCA6390 load the board file differently, add support for that
and the method is chosen using bus_params variables.

Add support to create board name for different targets. This board name is
used to parse the board data from board-2.bin for ahb/pci based targets.

As struct target_mem_chunk::vaddr was changed from 'u32' to 'u32 *' in
ath11k_qmi_assign_target_mem_chunk() vaddr assignments were changed to NULL to
avoid a compilation warning. IPQ8074 does not use the vaddr field for anything
so that change does not affect functionality.

At the moment this only supports board files with BIN type. Support for ELF
type, which seems to be more popular on QCA6390 devices, needs to be added later.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-3-git-send-email-kvalo@codeaurora.org

ath11k: use remoteproc only with AHB devices

QCA6390 and other PCI devices use MHI based firmware loading and do not use
remoteproc, so enable it only for AHB devices.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-11-git-send-email-kvalo@codeaurora.org

ath11k: pci: add HAL, CE and core initialisation

Define CE pipe/qmi config and setup pci irq for the
same. Call ath11k_core_init().

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-10-git-send-email-kvalo@codeaurora.org

ath11k: implement ath11k_core_pre_init()

This is needed to initialise hw_params before MHI registration starts. MHI
needs location of firmware directory and that's delivered via hw_params.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-8-git-send-email-kvalo@codeaurora.org

ath11k: add simple PCI client driver for QCA6390 chipset

QCA6390 is a PCI based 11ax chipset, split AHB into own kernel module
ath11k_ahb.ko and add ath11k_pci.ko for PCI devices.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-5-git-send-email-kvalo@codeaurora.org

ath11k: move ring mask definitions to hw_params

This is needed for splitting ahb and pci modules as they have different ring
mask settings.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-4-git-send-email-kvalo@codeaurora.org

ath11k: add hw_params entry for QCA6390

Define own firmware directory and settings for QCA6390.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-3-git-send-email-kvalo@codeaurora.org

ath11k: don't use defines in hw_params

These defines are not used anywhere else so to avoid extra indirection add the
values directly to hw_params.

No functional changes. Compile tested only.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-12-git-send-email-kvalo@codeaurora.org

ath11k: change ath11k_core_fetch_board_data_api_n() to use ath11k_core_create_firmware_path()

Use the helper added in previous comment to create the full path, instead of doing it manually.

No functional changes. Compile tested only.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-9-git-send-email-kvalo@codeaurora.org

ath11k: don't use defines for hw specific firmware directories

The downside of using defines in struct ath11k_hw_params.fw.dir is that it's
easy to get it wrong as the full path is not visible. So drop the use of
defines and instead create the patch runtime using a static inline function
ath11k_core_create_firmware_path(). Hopefully this reduces the chances of using
incorrect firmware path.

No functional changes. Compile tested only.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-8-git-send-email-kvalo@codeaurora.org

ath11k: create a common function to request all firmware files

To avoid duplicating the logic how the full firmware path is created create a
common function ath11k_core_firmware_request() and convert also qmi.c to use it.

Also remove a useless info print, it's more like a debug message anyway.

No functional changes. Compile tested only.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-7-git-send-email-kvalo@codeaurora.org

ath11k: Add bdf-addr in hw_params

bdf-addr is different for IPQ8074 and IPQ6018 so add it to hw_params.

No functional changes. Compile tested only.

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-6-git-send-email-kvalo@codeaurora.org

ath11k: add hw_ops for pdev id to hw_mac mapping

pdev_id to hw_mac is different for ipq8074 and ipq6018
Below table has the mapping

pdev_id ipq8074 ipq6018
------- ------- -------
0 0 0
1 2 1
2 1 Not applicable

No functional changes. Compile tested only.

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-5-git-send-email-kvalo@codeaurora.org

ath11k: define max_radios in hw_params

IPQ6018 needs different value for max_radios so make it configurable via hw_params.

No functional changes. Compile tested only.

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-4-git-send-email-kvalo@codeaurora.org

ath11k: convert ath11k_hw_params to an array

Convert to ath11k_hw_params to an array to make it possible add new hardware in
the future, for example IPQ6018 or QCA6390.

No functional changes. Compile tested only.

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-3-git-send-email-kvalo@codeaurora.org

ath11k: add support for spectral scan

spectral scan control interface is exposed through debugfs eentry.
Relayfs is used to collect the spectral data. These interfaces are
similar to ath10k spectral.

spectral debugfs interfaces are below,

echo background > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan0 > fft_samples.dump

Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-2-git-send-email-periyasa@codeaurora.org

ath11k: Remove bus layer includes from upper layer

Bus level header files needs to be abstracted by upper
layer. Remove bus layer includes by adding appropriate header
files.

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200506094400.4740-4-govinds@codeaurora.org

ath11k: Add drv private for bus opaque struct

Add drv private opaque structure to have bus level
structure for multibus support.

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200506094400.4740-3-govinds@codeaurora.org

ath11k: Add support for multibus support

Current design supports only AHB interface for
11ax chipset. Refactor the code by adding hif layer
for bus level abstraction to support PCI based device.

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200506094400.4740-2-govinds@codeaurora.org

ath11k: add thermal sensor device support

Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.

Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,

cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input

Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath11k: add thermal cooling device support

Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by suspending all data tx queues by given percentage of time. The
thermal device allows user to configure duty cycle.

Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.

/sys/class/ieee80211/phy*/device/cooling_device.

To set duty cycle as 40%,

echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state

Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath11k: fix warn-on in disassociation

In multi AP VAP scenario, when user bring down the interfaces. mac80211 mark
the interface down for the duplicated VAP and removed from the
local->interfaces list. ath11k_mac_get_arvif() is dependent on
ieee80211_iterate_active_interfaces_atomic() API to find the vdev id
in a given radio. In disassociation path, ath11k_mac_get_arvif() not
able to find the given vdev id since that VAP is removed from the
local->interfaces list. since sta_state callback throws error, mac80211 log
the below WARN_ON_ONCE message.

Fixed it by storing the allocated_vdev_map in each radio structure to maintain
the created vdev id bits. so that we can directly mask this against the given
vdev_id to find out the ar from the vdev_id.

WARN LOG:

WARNING: at net/mac80211/sta_info.c:1008
CPU: 2 PID: 2135 Comm: hostapd Not tainted #1
Hardware name: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C1 (DT)
task: ffffffc03a43d800 ti: ffffffc03a43d800 task.ti: ffffffc03a43d800
PC is at sta_set_sinfo+0x9dc/0xad4 [mac80211]
LR is at sta_set_sinfo+0x9cc/0xad4 [mac80211]
pc : [<ffffffbffce2a008>] lr : [<ffffffbffce29ff8>] pstate: 20000145
sp : ffffffc02cedb5f0
x29: ffffffc02cedb5f0 x28: ffffffc03a43d800
x27: 0000000000000014 x26: 0000000000000001
x25: ffffffc02cfc4000 x24: ffffffc036905508
x23: 0000000000000012 x22: ffffffc02cedb670
x21: ffffffc03bc64880 x20: ffffffc036904f80
x19: ffffffc02ae31000 x18: 00000000b019f3a1
x17: 0000000057f30331 x16: 00000000d8d1998e
x15: 0000000000000066 x14: 393a35383a36343a
x13: 6337203a6e6f6974 x12: 6174732065746169
x11: 636f737361736964 x10: 206f742064656c69
x9 : 6146203a31696669 x8 : 6337203a6e6f6974
x7 : 6174732065746169 x6 : ffffffc0008c33f6
x5 : 0000000000000000 x4 : 0000000000000000
x3 : 0000000000000000 x2 : 00000000ffffff92
x1 : 0000000000000000 x0 : ffffffbffcea1091
---[ end trace 63c4b1c527345d5a ]---
Call trace:
[<ffffffbffce2a008>] sta_set_sinfo+0x9dc/0xad4 [mac80211]
[<ffffffbffce2a2c4>] __sta_info_flush+0xec/0x130 [mac80211]
[<ffffffbffce3dc48>] ieee80211_nan_func_match+0x1a34/0x23e4 [mac80211]
[<ffffffbffcde03e0>] __cfg80211_stop_ap+0x60/0xf0 [cfg80211]
[<ffffffbffcdb6d08>] __cfg80211_leave+0x110/0x150 [cfg80211]
[<ffffffbffcdb6d78>] cfg80211_leave+0x30/0x48 [cfg80211]
[<ffffffbffcdb6fbc>] cfg80211_init_wdev+0x22c/0x808 [cfg80211]
[<ffffffc0000afe28>] notifier_call_chain+0x50/0x84
[<ffffffc0000afefc>] raw_notifier_call_chain+0x14/0x1c
[<ffffffc0004ae94c>] call_netdevice_notifiers_info+0x5c/0x6c
[<ffffffc0004ae96c>] call_netdevice_notifiers+0x10/0x18
[<ffffffc0004aea80>] __dev_close_many+0x54/0xc0
[<ffffffc0004aeb50>] dev_close_many+0x64/0xdc
[<ffffffc0004b0b70>] rollback_registered_many+0x138/0x2f4
[<ffffffc0004b0d4c>] rollback_registered+0x20/0x34
[<ffffffc0004b34b4>] unregister_netdevice_queue+0x68/0xa8
[<ffffffbffce3870c>] ieee80211_if_remove+0x84/0xc0 [mac80211]
[<ffffffbffce3e588>] ieee80211_nan_func_match+0x2374/0x23e4 [mac80211]
[<ffffffbffcdc29e8>] cfg80211_wext_giwscan+0x1000/0x1140 [cfg80211]
[<ffffffbffcb2a87c>] backport_genlmsg_multicast_allns+0x158/0x1b4 [compat]
[<ffffffc0004e0944>] genl_family_rcv_msg+0x258/0x2c0
[<ffffffc0004e09f4>] genl_rcv_msg+0x48/0x6c
[<ffffffc0004dfb50>] netlink_rcv_skb+0x5c/0xc4
[<ffffffc0004e06d8>] genl_rcv+0x34/0x48
[<ffffffc0004df570>] netlink_unicast+0x12c/0x1e0
[<ffffffc0004df9a4>] netlink_sendmsg+0x2bc/0x2dc
[<ffffffc00049a540>] sock_sendmsg+0x18/0x2c
[<ffffffc00049ab94>] ___sys_sendmsg+0x1bc/0x248
[<ffffffc00049ba24>] __sys_sendmsg+0x40/0x68
[<ffffffc00049ba5c>] SyS_sendmsg+0x10/0x20
[<ffffffc000085db0>] el0_svc_naked+0x24/0x28

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath11k: rename ath11k_wmi_base instances from wmi_sc to wmi_ab

This makes the code consistent with the recent sc to ab rename.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath11k: Setup REO destination ring before sending wmi_init command

Firmware expects all the required REO destination rings setup
while processing wmi_init command. Not doing this causes connected
stations getting disconnected and not able to connect back.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath11k: Move mac80211 hw allocation before wmi_init command

This is to prepare REO ring setup before sending wmi_init command.
Firmware expects all the required REO rings to be setup while processing
wmi_init command. But as per the current initialization sequence, REO ring
configurations are done only after wmi_init command is sent.
Also refactoring ath11k_mac_create() into ath11k_mac_alloc() and
ath11k_mac_register() to it mac80211 hw structure available before sending
wmi_init command.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath11k: unlock mutex during failure in qmi fw ready

qmi firmware ready event start to initialize the core modules and
the sequence executed with mutex lock. In case of any failure
mutex should be unlocked otherwise it will hang during the recovery.

Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath11k: driver for Qualcomm IEEE 802.11ax devices

ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first
supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k
uses mac80211 and supports AP, Station and Mesh modes.

Even though ath11k has some similar code as with ath10k (especially
the WMI layer) it was concluded to be simpler to have a "clean start"
for ath11k code base and not try to share the code with ath10k. This
makes maintenance easier and avoids major changes in ath10k, which
would have significantly increased the risk of regressions in existing
setups.

Even though the driver is very similar with ath10k but there are major
differences as well. The datapath is completely different. ath11k
supports multiple MACs, called "soc" in the firmware interface. And
there's only one WMI interface to support.

Currently ath11k supports only IEEE 802.11ac mode, but patches for
802.11ax are available and they will be submitted after ath11k is
accepted to upstream.

The firmware images are available from ath11k-firmware repository but
they will be also submitted to linux-firmware:

https://github.com/kvalo/ath11k-firmware

This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1.

The driver has had multiple authors who are listed in alphabetical
order below.

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>