net: phy: microchip: run phy initialization during each link update

PHY initialization is supposed to run on every mode changes.
"lan87xx_config_aneg()" verifies every mode change using
"phy_modify_changed()" function. Earlier code had phy_modify_changed()
followed by genphy_soft_reset. But soft_reset resets all the
pre-configured register values to default state, and lost all the
initialization done. With this reason gen_phy_reset was removed.
But it need to go through init sequence each time the mode changed.
Update lan87xx_config_aneg() to invoke phy_init once successful mode
update is detected.

PHY init sequence added in lan87xx_phy_init() have slave init
commands executed every time. Update the init sequence to run
slave init only if phydev is in slave mode.

Test setup contains LAN9370 EVB connected to SAMA5D3 (Running DSA),
and issue can be reproduced by connecting link to any of the available
ports after SAMA5D3 boot-up. With this issue, port will fail to
update link state. But once the SAMA5D3 is reset with LAN9370 link in
connected state itself, on boot-up link state will be reported as UP. But
Again after some time, if link is moved to DOWN state, it will not get
reported.

Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230120104733.724701-1-rakesh.sankaranarayanan@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: phy: lan87xx: change interrupt src of link_up to comm_ready

Currently phy link up/down interrupt is enabled using the
LAN87xx_INTERRUPT_MASK register. In the lan87xx_read_status function,
phy link is determined using the T1_MODE_STAT_REG register comm_ready bit.
comm_ready bit is set using the loc_rcvr_status & rem_rcvr_status.
Whenever the phy link is up, LAN87xx_INTERRUPT_SOURCE link_up bit is set
first but comm_ready bit takes some time to set based on local and
remote receiver status.
As per the current implementation, interrupt is triggered using link_up
but the comm_ready bit is still cleared in the read_status function. So,
link is always down. Initially tested with the shared interrupt
mechanism with switch and internal phy which is working, but after
implementing interrupt controller it is not working.
It can fixed either by updating the read_status function to read from
LAN87XX_INTERRUPT_SOURCE register or enable the interrupt mask for
comm_ready bit. But the validation team recommends the use of comm_ready
for link detection.
This patch fixes by enabling the comm_ready bit for link_up in the
LAN87XX_INTERRUPT_MASK_2 register (MISC Bank) and link_down in
LAN87xx_INTERRUPT_MASK register.

Fixes: 8a1b415d70b7 ("net: phy: added ethtool master-slave configuration support")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220905152750.5079-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: phy: LAN937x: add interrupt support for link detection

Added the config_intr and handle_interrupt for the LAN937x phy which is
same as the LAN87xx phy.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220423154727.29052-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: phy: LAN87xx: add ethtool SQI support

This patch add the support for measuring Signal Quality Index for
LAN87xx and LAN937x T1 Phy. It uses the SQI Method 5 for obtaining the
values.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: phy: LAN937x: added PHY_POLL_CABLE_TEST flag

Added the phy_poll_cable_test flag for the lan937x phy driver.
Tested using command - ethtool --cable-test <dev>

Fixes: 680baca546f2 ("net: phy: added the LAN937x phy support")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: LAN87xx: remove genphy_softreset in config_aneg

When the T1 phy master/slave state is changed, at the end of config_aneg
function genphy_softreset is called. After the reset all the registers
configured during the config_init are restored to default value.
To avoid this, removed the genphy_softreset call.

v1->v2
------
Added the author in cc

Fixes: 8a1b415d70b7 ("net: phy: added ethtool master-slave configuration support")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: lan87xx: use genphy_read_master_slave in read_status

To read the master slave configuration of the LAN87xx T1 phy, used the
generic phy driver genphy_read_master_slave function. Removed the local
lan87xx_read_master_slave function.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: phy: added ethtool master-slave configuration support

To configure the T1 phy as master or slave using the ethtool -s <dev>
master-slave <forced-master/forced-slave>, the config_aneg and read
status functions are added.

Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: added the LAN937x phy support

LAN937x T1 switch is based on LAN87xx Phy, so reusing the init script of
the LAN87xx. There is a workaround in accessing the DSP bank register
for LAN937x Phy. Whenever there is a bank switch to DSP registers, then
we need a one dummy read access before proceeding to the actual register
access.

Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: updated the initialization routine for LAN87xx

The new initialization sequence is the improvement to the existing init
routine. Init routine does soft reset, run init script and set
Hw_init. Added the new access_smi_poll_timeout() for polling smi
bank write.

Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: removed empty lines in LAN87XX

Removed the empty lines in struct phy_drivers.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: used the PHY_ID_MATCH_MODEL macro for LAN87XX

Used the PHY_ID_MATCH_MODEL MACRO for describing the phy_id and
phy_id_mask.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: used genphy_soft_reset for phy reset in LAN87xx

Replaced the current code of resetting of LAN87xx phy to
genphy_soft_reset library function.

Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: microchip_t1: add lan87xx_config_rgmii_delay for lan87xx phy

Add a function to initialize phy rgmii delay according to phydev->interface.

Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211101162119.29275-1-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: phy: microchip_t1: add cable test support for lan87xx phy

Add a basic cable test (diagnostic) support for lan87xx phy.
Tested with LAN8770 for connected/open/short wires using ethtool.

Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: microchip: remove the use of .ack_interrupt()

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: phy: microchip: implement generic .handle_interrupt() callback

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: phy: microchip_t1: Don't set .config_aneg

The .config_aneg in microchip_t1 is genphy_config_aneg, so it's not
needed, because the phy core will call genphy_config_aneg() if the
.config_aneg is NULL.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201109091605.3951c969@xhacker.debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: phy: microchip_t1: add lan87xx_phy_init to initialize the lan87xx phy.

lan87xx_phy_init() initializes the lan87xx phy hardware
including its TC10 Wake-up and Sleep features.

Fixes: 3e50d2da5850 ("Add driver for Microchip LAN87XX T1 PHYs")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
v0->v1:
- Add more details in the commit message and source comments.
- Update to the latest initialization sequences.
- Add access_ereg_modify_changed().
- Fix access_ereg() to access SMI bank correctly.
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: remove calls to genphy_config_init

Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy_config_init does is removing features that are set as
supported but can't be auto-detected. Basically it duplicates the
code in genphy_read_abilities. Therefore remove such calls from
all PHY drivers.

v2:
- remove call also from new adin PHY driver
v3:
- pass NULL as config_init function pointer for dp83848

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: remove flag PHY_HAS_INTERRUPT from driver configs

Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: Replace phy driver features u32 with link_mode bitmap

This is one step in allowing phylib to make use of link_mode bitmaps,
instead of u32 for supported and advertised features. Convert the phy
drivers to use bitmaps to indicates the features they support.

Build bitmap equivalents of the u32 values at runtime, and have the
drivers point to the appropriate bitmap. These bitmaps are shared, and
we don't want a driver to modify them. So mark them __ro_after_init.

Within phylib, the features bitmap is currently turned back into a
u32. This will be removed once the whole of phylib, and the drivers
are converted to use bitmaps.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

microchip_t1: Add driver for Microchip LAN87XX T1 PHYs

Add driver for Microchip LAN87XX T1 PHYs

This patch support driver for Microchp T1 PHYs.
There will be followup patches to this driver to support T1 PHY
features such as cable diagnostics, signal quality indicator(SQI),
sleep and wakeup (TC10) support.

Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>