net: axienet: Introduce dmaengine support

Add dmaengine framework to communicate with the xilinx DMAengine
driver(AXIDMA).

Axi ethernet driver uses separate channels for transmit and receive.
Add support for these channels to handle TX and RX with skb and
appropriate callbacks. Also add axi ethernet core interrupt for
dmaengine framework support.

The dmaengine framework was extended for metadata API support.
However it still needs further enhancements to make it well suited for
ethernet usecases. The ethernet features i.e ethtool set/get of DMA IP
properties, ndo_poll_controller,(mentioned in TODO) are not supported
and it requires follow-up discussions.

dmaengine support has a dependency on xilinx_dma as it uses
xilinx_vdma_channel_set_config() API to reset the DMA IP
which internally reset MAC prior to accessing MDIO.

Benchmark with netperf:

xilinx-zcu102-20232:~$ netperf -H 192.168.10.20 -t TCP_STREAM
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET
to 192.168.10.20 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec

131072 16384 16384 10.02 886.69

xilinx-zcu102-20232:~$ netperf -H 192.168.10.20 -t UDP_STREAM
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET
to 192.168.10.20 () port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec

212992 65507 10.00 15851 0 830.66
212992 10.00 15851 830.66

Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1700074613-1977070-4-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: axienet: Preparatory changes for dmaengine support

The axiethernet driver has inbuilt dma programming. In order to add
dmaengine support and make it's integration seamless the current axidma
inbuilt programming code is put under use_dmaengine check.

It also performs minor code reordering to minimize conditional
use_dmaengine checks and there is no functional change. It uses
"dmas" property to identify whether it should use a dmaengine
framework or inbuilt axidma programming.

Signed-off-by: Sarath Babu Naidu Gaddam <sarath.babu.naidu.gaddam@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1700074613-1977070-3-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: axienet: Fix check for partial TX checksum

Due to a typo, the code checked the RX checksum feature in the TX path.

Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20231122004219.3504219-1-samuel.holland@sifive.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: xilinx: Convert to platform remove callback returning void

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().

Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Explicitly include correct DT includes

The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.

Acked-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230727014944.3972546-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: axienet: Move reset before 64-bit DMA detection

64-bit DMA detection will fail if axienet was started before (by boot
loader, boot ROM, etc). In this state axienet will not start properly.
XAXIDMA_TX_CDESC_OFFSET + 4 register (MM2S_CURDESC_MSB) is used to detect
64-bit DMA capability here. But datasheet says: When DMACR.RS is 1
(axienet is in enabled state), CURDESC_PTR becomes Read Only (RO) and
is used to fetch the first descriptor. So iowrite32()/ioread32() trick
to this register to detect 64-bit DMA will not work.
So move axienet reset before 64-bit DMA detection.

Fixes: f735c40ed93c ("net: axienet: Autodetect 64-bit DMA capability")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20230622192245.116864-1-fido_max@inbox.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: phylink: pass neg_mode into phylink_mii_c22_pcs_config()

Convert fman_dtsec, xilinx_axienet and pcs-lynx to pass the neg_mode
into phylink_mii_c22_pcs_config(). Where appropriate, drivers are
updated to have neg_mode passed into their pcs_config() and
pcs_link_up() functions. For other drivers, we just hoist the call
to phylink_pcs_neg_mode() to their pcs_config() method out of
phylink_mii_c22_pcs_config().

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Do-00EaFM-Ra@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: remove explicit phylink_generic_validate() references

Virtually all conventional network drivers are now converted to use
phylink_generic_validate() - only DSA drivers and fman_memac remain,
so lets remove the necessity for network drivers to explicitly set
this member, and default to phylink_generic_validate() when unset.
This is possible as .validate must currently be set.

Any remaining instances that have not been addressed by this patch can
be fixed up later.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/E1or0FZ-001tRa-DI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: axiemac: add PM callbacks to support suspend/resume

Support basic system-wide suspend and resume functions

Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Remove the obsolte u64_stats_fetch_*_irq() users (drivers).

Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.

Convert to the regular interface.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: drop the weight argument from netif_napi_add

We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().

Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ll_temac: axienet: delete unnecessary blank lines and spaces

Cleaning some static warnings of indent.

Signed-off-by: huangjunxian <huangjunxian6@hisilicon.com>
Signed-off-by: Haoyue Xu <xuhaoyue1@hisilicon.com>
Reviewed-by: Harini Katakam <harini.katakam@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ll_temac: axienet: align with open parenthesis

Cleaning some static warnings of open parenthesis.

Signed-off-by: huangjunxian <huangjunxian6@hisilicon.com>
Signed-off-by: Haoyue Xu <xuhaoyue1@hisilicon.com>
Reviewed-by: Harini Katakam <harini.katakam@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: axienet: Switch to 64-bit RX/TX statistics

The RX and TX byte/packet statistics in this driver could be overflowed
relatively quickly on a 32-bit platform. Switch these stats to use the
u64_stats infrastructure to avoid this.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220829233901.3429419-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: move from strlcpy with unused retval to strscpy

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: axienet: add missing error return code in axienet_probe()

It should return error code in error path in axienet_probe().

Fixes: 00be43a74ca2 ("net: axienet: make the 64b addresable DMA depends on 64b archectures")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220616062917.3601-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: axienet: make the 64b addresable DMA depends on 64b archectures

Currently it is not safe to config the IP as 64-bit addressable on 32-bit
archectures, which cannot perform a double-word store on its descriptor
pointers. The pointer is 64-bit wide if the IP is configured as 64-bit,
and the device would process the partially updated pointer on some
states if the pointer was updated via two store-words. To prevent such
condition, we force a probe fail if we discover that the IP has 64-bit
capability but it is not running on a 64-Bit kernel.

This is a series of patch (1/2). The next patch must be applied in order
to make 64b DMA safe on 64b archectures.

Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reported-by: Max Hsu <max.hsu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Use NAPI for TX completion path

This driver was using the TX IRQ handler to perform all TX completion
tasks. Under heavy TX network load, this can cause significant irqs-off
latencies (found to be in the hundreds of microseconds using ftrace).
This can cause other issues, such as overrunning serial UART FIFOs when
using high baud rates with limited UART FIFO sizes.

Switch to using a NAPI poll handler to perform the TX completion work
to get this out of hard IRQ context and avoid the IRQ latency impact.
A separate poll handler is used for TX and RX since they have separate
IRQs on this controller, so that the completion work for each of them
stays on the same CPU as the interrupt.

Testing on a Xilinx MPSoC ZU9EG platform using iperf3 from a Linux PC
through a switch at 1G link speed showed no significant change in TX or
RX throughput, with approximately 941 Mbps before and after. Hard IRQ
time in the TX throughput test was significantly reduced from 12% to
below 1% on the CPU handling TX interrupts, with total hard+soft IRQ CPU
usage dropping from about 56% down to 48%.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Be more careful about updating tx_bd_tail

The axienet_start_xmit function was updating the tx_bd_tail variable
multiple times, with potential rollbacks on error or invalid
intermediate positions, even though this variable is also used in the
TX completion path. Use READ_ONCE where this variable is read and
WRITE_ONCE where it is written to make this update more atomic, and
move the write before the MMIO write to start the transfer, so it is
protected by that implicit write barrier.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axiemac: use a phandle to reference pcs_phy

In some SGMII use cases where both a fixed link external PHY and the
internal PCS/PMA PHY need to be configured, we should explicitly use a
phandle "pcs-phy" to get the reference to the PCS/PMA PHY. Otherwise, the
driver would use "phy-handle" in the DT as the reference to both the
external and the internal PCS/PMA PHY.

In other cases where the core is connected to a SFP cage, we could still
point phy-handle to the intenal PCS/PMA PHY, and let the driver connect
to the SFP module, if exist, via phylink.

Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: factor out phy_node in struct axienet_local

the struct member `phy_node` of struct axienet_local is not used by the
driver anymore after initialization. It might be a remnent of old code
and could be removed.

Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: setup mdio unconditionally

The call to axienet_mdio_setup should not depend on whether "phy-node"
pressents on the DT. Besides, since `lp->phy_node` is used if PHY is in
SGMII or 100Base-X modes, move it into the if statement. And the next patch
will remove `lp->phy_node` from driver's private structure and do an
of_node_put on it right away after use since it is not used elsewhere.

Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Use napi_alloc_skb when refilling RX ring

Use napi_alloc_skb to allocate memory when refilling the RX ring
in axienet_poll for more efficiency. napi_alloc_skb() can reuse
softirq-local cache of freed skbs which may still be cache-warm
and skipping allocator calls.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220308211013.1530955-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: axienet: add coalesce timer ethtool configuration

Add the ability to configure the RX/TX coalesce timer with ethtool.
Change default setting to scale with the clock rate rather than being a
fixed number of clock cycles.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: implement NAPI and GRO receive

Implement NAPI and GRO receive. In addition to better performance, this
also avoids handling RX packets in hard IRQ context, which reduces the
IRQ latency impact to other devices.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: don't set IRQ timer when IRQ delay not used

When the RX or TX coalesce count is set to 1, there's no point in
setting the delay timer value since an interrupt will already be raised
on every packet, and the delay interrupt just causes extra pointless
interrupts.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Clean up DMA start/stop and error handling

Simplify the DMA error handling process, and remove some duplicated code
between the DMA error handling and the stop function.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Clean up device used for DMA calls

Instead of using lp->ndev.parent to find the correct device to use for
DMA API calls, just use the dev attribute in the device structure.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: fix RX ring refill allocation failure handling

If a memory allocation error occurred during an attempt to refill a slot
in the RX ring after the packet was received, the hardware tail pointer
would still have been updated to point to or past the slot which remained
marked as previously completed. This would likely result in the DMA engine
raising an error when it eventually tried to use that slot again.

If a slot cannot be refilled, then just stop processing and do not move
the tail pointer past it. On the next attempt, we should skip receiving
the packet from the empty slot and just try to refill it again.

This failure mode has not actually been observed, but was found as part
of other driver updates.

Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: xilinx: cleanup comments

Remove the second 'the'.
Replacements:
endiannes to endianness
areconnected to are connected
Mamagement to Management
undoccumented to undocumented
Xilink to Xilinx
strucutre to structure

Change kernel-doc comment style to c style for
/* Management ...

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: replace mdiobus_write() with mdiodev_write()

Commit 0ebecb2644c8 ("net: mdio: Add helper functions for accessing
MDIO devices") added support for mdiodev accessor operations that
neatly wrap the mdiobus accessor operations. Since we are dealing with
a mdio device here, update the driver to use mdiodev_write().

Tested-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: convert to phylink_pcs

Convert axienet to use the phylink_pcs layer, resulting in it no longer
being a legacy driver.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: increase default TX ring size to 128

With previous changes to make the driver handle the TX ring size more
correctly, the default TX ring size of 64 appears to significantly
bottleneck TX performance to around 600 Mbps on a 1 Gbps link on ZynqMP.
Increasing this to 128 seems to bring performance up to near line rate and
shouldn't cause excess bufferbloat (this driver doesn't yet support modern
byte-based queue management).

Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: fix for TX busy handling

Network driver documentation indicates we should be avoiding returning
NETDEV_TX_BUSY from ndo_start_xmit in normal cases, since it requires
the packets to be requeued. Instead the queue should be stopped after
a packet is added to the TX ring when there may not be enough room for an
additional one. Also, when TX ring entries are completed, we should only
wake the queue if we know there is room for another full maximally
fragmented packet.

Print a warning if there is insufficient space at the start of start_xmit,
since this should no longer happen.

Combined with increasing the default TX ring size (in a subsequent
patch), this appears to recover the TX performance lost by previous changes
to actually manage the TX ring state properly.

Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: fix number of TX ring slots for available check

The check for the number of available TX ring slots was off by 1 since a
slot is required for the skb header as well as each fragment. This could
result in overwriting a TX ring slot that was still in use.

Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix TX ring slot available check

The check for whether a TX ring slot was available was incorrect,
since a slot which had been loaded with transmit data but the device had
not started transmitting would be treated as available, potentially
causing non-transmitted slots to be overwritten. The control field in
the descriptor should be checked, rather than the status field (which may
only be updated when the device completes the entry).

Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: limit minimum TX ring size

The driver will not work properly if the TX ring size is set to below
MAX_SKB_FRAGS + 1 since it needs to hold at least one full maximally
fragmented packet in the TX ring. Limit setting the ring size to below
this value.

Fixes: 8b09ca823ffb4 ("net: axienet: Make RX/TX ring sizes configurable")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: add missing memory barriers

This driver was missing some required memory barriers:

Use dma_rmb to ensure we see all updates to the descriptor after we see
that an entry has been completed.

Use wmb and rmb to avoid stale descriptor status between the TX path and
TX complete IRQ path.

Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: reset core on initialization prior to MDIO access

In some cases where the Xilinx Ethernet core was used in 1000Base-X or
SGMII modes, which use the internal PCS/PMA PHY, and the MGT
transceiver clock source for the PCS was not running at the time the
FPGA logic was loaded, the core would come up in a state where the
PCS could not be found on the MDIO bus. To fix this, the Ethernet core
(including the PCS) should be reset after enabling the clocks, prior to
attempting to access the PCS using of_mdio_find_device.

Fixes: 1a02556086fc (net: axienet: Properly handle PCS/PMA PHY for 1000BaseX mode)
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Wait for PhyRstCmplt after core reset

When resetting the device, wait for the PhyRstCmplt bit to be set
in the interrupt status register before continuing initialization, to
ensure that the core is actually ready. When using an external PHY, this
also ensures we do not start trying to access the PHY while it is still
in reset. The PHY reset is initiated by the core reset which is
triggered just above, but remains asserted for 5ms after the core is
reset according to the documentation.

The MgtRdy bit could also be waited for, but unfortunately when using
7-series devices, the bit does not appear to work as documented (it
seems to behave as some sort of link state indication and not just an
indication the transceiver is ready) so it can't really be relied on for
this purpose.

Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: increase reset timeout

The previous timeout of 1ms was too short to handle some cases where the
core is reset just after the input clocks were started, which will
be introduced in an upcoming patch. Increase the timeout to 50ms. Also
simplify the reset timeout checking to use read_poll_timeout.

Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: mark as a legacy_pre_march2020 driver

axienet has a PCS, but does not make use of the phylink PCS support.
Mark it was a pre-March 2020 driver.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: extend ringparam setting/getting API with rx_buf_len

Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.

Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: use phylink_generic_validate()

axienet has no special behaviour in its validation implementation, so
can be switched to phylink_generic_validate().

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: remove interface checks in axienet_validate()

As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: populate supported_interfaces member

Populate the phy_interface_t bitmap for the Xilinx axienet driver with
interfaces modes supported by the MAC.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: convert users of bitmap_foo() to linkmode_foo()

This converts instances of
bitmap_foo(args..., __ETHTOOL_LINK_MODE_MASK_NBITS)
to
linkmode_foo(args...)

I manually fixed up some lines to prevent them from being excessively
long. Otherwise, this change was generated with the following semantic
patch:

// Generated with
// echo linux/linkmode.h > includes
// git grep -Flf includes include/ | cut -f 2- -d / | cat includes - \
// | sort | uniq | tee new_includes | wc -l && mv new_includes includes
// and repeating until the number stopped going up
@i@
@@

(
#include <linux/acpi_mdio.h>
|
#include <linux/brcmphy.h>
|
#include <linux/dsa/loop.h>
|
#include <linux/dsa/sja1105.h>
|
#include <linux/ethtool.h>
|
#include <linux/ethtool_netlink.h>
|
#include <linux/fec.h>
|
#include <linux/fs_enet_pd.h>
|
#include <linux/fsl/enetc_mdio.h>
|
#include <linux/fwnode_mdio.h>
|
#include <linux/linkmode.h>
|
#include <linux/lsm_audit.h>
|
#include <linux/mdio-bitbang.h>
|
#include <linux/mdio.h>
|
#include <linux/mdio-mux.h>
|
#include <linux/mii.h>
|
#include <linux/mii_timestamper.h>
|
#include <linux/mlx5/accel.h>
|
#include <linux/mlx5/cq.h>
|
#include <linux/mlx5/device.h>
|
#include <linux/mlx5/driver.h>
|
#include <linux/mlx5/eswitch.h>
|
#include <linux/mlx5/fs.h>
|
#include <linux/mlx5/port.h>
|
#include <linux/mlx5/qp.h>
|
#include <linux/mlx5/rsc_dump.h>
|
#include <linux/mlx5/transobj.h>
|
#include <linux/mlx5/vport.h>
|
#include <linux/of_mdio.h>
|
#include <linux/of_net.h>
|
#include <linux/pcs-lynx.h>
|
#include <linux/pcs/pcs-xpcs.h>
|
#include <linux/phy.h>
|
#include <linux/phy_led_triggers.h>
|
#include <linux/phylink.h>
|
#include <linux/platform_data/bcmgenet.h>
|
#include <linux/platform_data/xilinx-ll-temac.h>
|
#include <linux/pxa168_eth.h>
|
#include <linux/qed/qed_eth_if.h>
|
#include <linux/qed/qed_fcoe_if.h>
|
#include <linux/qed/qed_if.h>
|
#include <linux/qed/qed_iov_if.h>
|
#include <linux/qed/qed_iscsi_if.h>
|
#include <linux/qed/qed_ll2_if.h>
|
#include <linux/qed/qed_nvmetcp_if.h>
|
#include <linux/qed/qed_rdma_if.h>
|
#include <linux/sfp.h>
|
#include <linux/sh_eth.h>
|
#include <linux/smsc911x.h>
|
#include <linux/soc/nxp/lpc32xx-misc.h>
|
#include <linux/stmmac.h>
|
#include <linux/sunrpc/svc_rdma.h>
|
#include <linux/sxgbe_platform.h>
|
#include <net/cfg80211.h>
|
#include <net/dsa.h>
|
#include <net/mac80211.h>
|
#include <net/selftests.h>
|
#include <rdma/ib_addr.h>
|
#include <rdma/ib_cache.h>
|
#include <rdma/ib_cm.h>
|
#include <rdma/ib_hdrs.h>
|
#include <rdma/ib_mad.h>
|
#include <rdma/ib_marshall.h>
|
#include <rdma/ib_pack.h>
|
#include <rdma/ib_pma.h>
|
#include <rdma/ib_sa.h>
|
#include <rdma/ib_smi.h>
|
#include <rdma/ib_umem.h>
|
#include <rdma/ib_umem_odp.h>
|
#include <rdma/ib_verbs.h>
|
#include <rdma/iw_cm.h>
|
#include <rdma/mr_pool.h>
|
#include <rdma/opa_addr.h>
|
#include <rdma/opa_port_info.h>
|
#include <rdma/opa_smi.h>
|
#include <rdma/opa_vnic.h>
|
#include <rdma/rdma_cm.h>
|
#include <rdma/rdma_cm_ib.h>
|
#include <rdma/rdmavt_cq.h>
|
#include <rdma/rdma_vt.h>
|
#include <rdma/rdmavt_qp.h>
|
#include <rdma/rw.h>
|
#include <rdma/tid_rdma_defs.h>
|
#include <rdma/uverbs_ioctl.h>
|
#include <rdma/uverbs_named_ioctl.h>
|
#include <rdma/uverbs_std_types.h>
|
#include <rdma/uverbs_types.h>
|
#include <soc/mscc/ocelot.h>
|
#include <soc/mscc/ocelot_ptp.h>
|
#include <soc/mscc/ocelot_vcap.h>
|
#include <trace/events/ib_mad.h>
|
#include <trace/events/rdma_core.h>
|
#include <trace/events/rdma.h>
|
#include <trace/events/rpcrdma.h>
|
#include <uapi/linux/ethtool.h>
|
#include <uapi/linux/ethtool_netlink.h>
|
#include <uapi/linux/mdio.h>
|
#include <uapi/linux/mii.h>
)

@depends on i@
expression list args;
@@

(
- bitmap_zero(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_zero(args)
|
- bitmap_copy(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_copy(args)
|
- bitmap_and(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_and(args)
|
- bitmap_or(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_or(args)
|
- bitmap_empty(args, ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_empty(args)
|
- bitmap_andnot(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_andnot(args)
|
- bitmap_equal(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_equal(args)
|
- bitmap_intersects(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_intersects(args)
|
- bitmap_subset(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_subset(args)
)

Add missing linux/mii.h include to mellanox. -DaveM

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet: use eth_hw_addr_set()

Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():

@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: extend coalesce setting uAPI with CQE mode

In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

dev_ioctl: split out ndo_eth_ioctl

Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.

Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.

This is a purely cosmetic change intended to help readers find
their way through the implementation.

Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Use devm_platform_get_and_ioremap_resource()

Use devm_platform_get_and_ioremap_resource() to simplify
code.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix fall-through warning for Clang

In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding a fallthrough statement instead of just
letting the code fall through to the next case.

Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20210528195831.GA39131@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

of: net: pass the dst buffer to of_get_mac_address()

of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.

There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.

Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().

Usually the code looks like:

const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);

This can then be simply rewritten as:

of_get_mac_address(np, ndev->dev_addr);

Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.

The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!

<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>

@@
identifier a.x;
@@
- if (<+... x ...+>) {}

@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}

@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}

@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>

All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Remove redundant dev_err call in axienet_probe()

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Enable more clocks

This driver was only enabling the first clock on the device, regardless
of its name. However, this controller logic can have multiple clocks
which should all be enabled. Add support for enabling additional clocks.
The clock names used are matching those used in the Xilinx version of this
driver as well as the Xilinx device tree generator, except for mgt_clk
which is not present there.

For backward compatibility, if no named clocks are present, the first
clock present is used for determining the MDIO bus clock divider.

Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: allow setups without MDIO

In setups with fixed-link settings there is no mdio node in DTS.
axienet_probe() already handles that gracefully but lp->mii_bus is
then NULL.

Fix code that tries to blindly grab the MDIO lock by introducing two helper
functions that make the locking conditional.

Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix probe error cleanup

The driver did not always clean up all allocated resources when probe
failed. Fix the probe cleanup path to clean up everything that was
allocated.

Fixes: 57baf8cc70ea ("net: axienet: Handle deferred probe on clock properly")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Support dynamic switching between 1000BaseX and SGMII

Newer versions of the Xilinx AXI Ethernet core (specifically version 7.2 or
later) allow the core to be configured with a PHY interface mode of "Both",
allowing either 1000BaseX or SGMII modes to be selected at runtime. Add
support for this in the driver to allow better support for applications
which can use both fiber and copper SFP modules.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: hook up nway_reset ethtool operation

Hook up the nway_reset ethtool operation to the corresponding phylink
function so that "ethtool -r" can be supported.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Handle deferred probe on clock properly

This driver is set up to use a clock mapping in the device tree if it is
present, but still work without one for backward compatibility. However,
if getting the clock returns -EPROBE_DEFER, then we need to abort and
return that error from our driver initialization so that the probe can
be retried later after the clock is set up.

Move clock initialization to earlier in the process so we do not waste as
much effort if the clock is not yet available. Switch to use
devm_clk_get_optional and abort initialization on any error reported.
Also enable the clock regardless of whether the controller is using an MDIO
bus, as the clock is required in any case.

Fixes: 09a0354cadec267be7f ("net: axienet: Use clock framework to get device clock rate")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: xilinx: axiethernet: Enable dynamic MDIO MDC

MDIO spec does not require an MDC at all times, only when MDIO
transactions are occurring. This patch allows the xilinx_axienet
driver to disable the MDC when not in use, and re-enable it when
needed. It also simplifies the driver by removing MDC disable
and enable in device reset sequence.

Signed-off-by: Clayton Rayment <clayton.rayment@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: axienet: Properly handle PCS/PMA PHY for 1000BaseX mode

Update the axienet driver to properly support the Xilinx PCS/PMA PHY
component which is used for 1000BaseX and SGMII modes, including
properly configuring the auto-negotiation mode of the PHY and reading
the negotiated state from the PHY.

Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/20201028171429.1699922-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: xilinx: remove redundant null check before clk_disable_unprepare()

Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: axienet: Allow DMA to beyond 4GB

With all DMA address accesses wrapped, we can actually support 64-bit
DMA if this option was chosen at IP integration time.
If the IP has been configured for an address width greater than 32 bits,
we assume the full 64 bit DMA width is working. In practise this will be
limited by the actual system address bus width, which will ideally be the
same as the DMA IP address width.
If this is not the case, the actual width can still be configured using a
dma-ranges property in the parent of the MAC node.

This increases the DMA mask on those systems to let the kernel choose
buffers from memory at higher addresses.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Autodetect 64-bit DMA capability

When newer revisions of the Axienet IP are configured for a 64-bit bus,
we *need* to write to the MSB part of the an address registers,
otherwise the IP won't recognise this as a DMA start condition.
This is even true when the actual DMA address comes from the lower 4 GB.

To autodetect this configuration, at probe time we write all 1's to such
an MSB register, and see if any bits stick. If this is configured for a
32-bit bus, those MSB registers are RES0, so reading back 0 indicates
that no MSB writes are necessary.
On the other hands reading anything other than 0 indicated the need to
write the MSB registers, so we set the respective flag.

The actual DMA mask stays at 32-bit for now. To help bisecting, a
separate patch will enable allocations from higher addresses.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Upgrade descriptors to hold 64-bit addresses

Newer revisions of the AXI DMA IP (>= v7.1) support 64-bit addresses,
both for the descriptors itself, as well as for the buffers they are
pointing to.
This is realised by adding "MSB" words for the next and phys pointer
right behind the existing address word, now named "LSB". These MSB words
live in formerly reserved areas of the descriptor.

If the hardware supports it, write both words when setting an address.
The buffer address is handled by two wrapper functions, the two
occasions where we set the next pointers are open coded.

For now this is guarded by a flag which we don't set yet.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Wrap DMA pointer writes to prepare for 64 bit

Newer versions of the Xilink DMA IP support busses with more than 32
address bits, by introducing an MSB word for the registers holding DMA
pointers (tail/current, RX/TX descriptor addresses).
On IP configured for more than 32 bits, it is also *required* to write
both words, to let the IP recognise this as a start condition for an
MM2S request, for instance.

Wrap the DMA pointer writes with a separate function, to add this
functionality later. For now we stick to the lower 32 bits.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Add mii-tool support

mii-tool is useful for debugging, and all it requires to work is to wire
up the ioctl ops function pointer.
Add this to the axienet driver to enable mii-tool.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Drop MDIO interrupt registers from ethtools dump

Newer revisions of the IP don't have these registers. Since we don't
really use them, just drop them from the ethtools dump.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Mark eth_irq as optional

According to the DT binding, the Ethernet core interrupt is optional.

Use platform_get_irq_optional() to avoid the error message when the
IRQ is not specified.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Check for DMA mapping errors

Especially with the default 32-bit DMA mask, DMA buffers are a limited
resource, so their allocation can fail.
So as the DMA API documentation requires, add error checking code after
dma_map_single() calls to catch the case where we run out of "low" memory.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Factor out TX descriptor chain cleanup

Factor out the code that cleans up a number of connected TX descriptors,
as we will need it to properly roll back a failed _xmit() call.
There are subtle differences between cleaning up a successfully sent
chain (unknown number of involved descriptors, total data size needed)
and a chain that was about to set up (number of descriptors known), so
cater for those variations with some extra parameters.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Improve DMA error handling

Since 0 is a valid DMA address, we cannot use the physical address to
check whether a TX descriptor is valid and is holding a DMA mapping.

Use the "cntrl" member of the descriptor to make this decision, as it
contains at least the length of the buffer, so 0 points to an
uninitialised buffer.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix DMA descriptor cleanup path

When axienet_dma_bd_init() bails out during the initialisation process,
it might do so with parts of the structure already allocated and
initialised, while other parts have not been touched yet. Before
returning in this case, we call axienet_dma_bd_release(), which does not
take care of this corner case.
This is most obvious by the first loop happily dereferencing
lp->rx_bd_v, which we actually check to be non NULL *afterwards*.

Make sure we only unmap or free already allocated structures, by:
- directly returning with -ENOMEM if nothing has been allocated at all
- checking for lp->rx_bd_v to be non-NULL *before* using it
- only unmapping allocated DMA RX regions

This avoids NULL pointer dereferences when initialisation fails.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Propagate failure of DMA descriptor setup

When we fail allocating the DMA buffers in axienet_dma_bd_init(), we
report this error, but carry on with initialisation nevertheless.

This leads to a kernel panic when the driver later wants to send a
packet, as it uses uninitialised data structures.

Make the axienet_device_reset() routine return an error value, as it
contains the DMA buffer initialisation. Make sure we propagate the error
up the chain and eventually fail the driver initialisation, to avoid
relying on non-initialised buffers.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Convert DMA error handler to a work queue

The DMA error handler routine is currently a tasklet, scheduled to run
after the DMA error IRQ was handled.
However it needs to take the MDIO mutex, which is not allowed to do in a
tasklet. A kernel (with debug options) complains consequently:
[ 614.050361] net eth0: DMA Tx error 0x174019
[ 614.064002] net eth0: Current BD is at: 0x8f84aa0ce
[ 614.080195] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935
[ 614.109484] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 40, name: kworker/u4:4
[ 614.135428] 3 locks held by kworker/u4:4/40:
[ 614.149075] #0: ffff000879863328 ((wq_completion)rpciod){....}, at: process_one_work+0x1f0/0x6a8
[ 614.177528] #1: ffff80001251bdf8 ((work_completion)(&task->u.tk_work)){....}, at: process_one_work+0x1f0/0x6a8
[ 614.209033] #2: ffff0008784e0110 (sk_lock-AF_INET-RPC){....}, at: tcp_sendmsg+0x24/0x58
[ 614.235429] CPU: 0 PID: 40 Comm: kworker/u4:4 Not tainted 5.6.0-rc3-00926-g4a165a9d5921 #26
[ 614.260854] Hardware name: ARM Test FPGA (DT)
[ 614.274734] Workqueue: rpciod rpc_async_schedule
[ 614.289022] Call trace:
[ 614.296871] dump_backtrace+0x0/0x1a0
[ 614.308311] show_stack+0x14/0x20
[ 614.318751] dump_stack+0xbc/0x100
[ 614.329403] ___might_sleep+0xf0/0x140
[ 614.341018] __might_sleep+0x4c/0x80
[ 614.352201] __mutex_lock+0x5c/0x8a8
[ 614.363348] mutex_lock_nested+0x1c/0x28
[ 614.375654] axienet_dma_err_handler+0x38/0x388
[ 614.389999] tasklet_action_common.isra.15+0x160/0x1a8
[ 614.405894] tasklet_action+0x24/0x30
[ 614.417297] efi_header_end+0xe0/0x494
[ 614.429020] irq_exit+0xd0/0xd8
[ 614.439047] __handle_domain_irq+0x60/0xb0
[ 614.451877] gic_handle_irq+0xdc/0x2d0
[ 614.463486] el1_irq+0xcc/0x180
[ 614.473451] __tcp_transmit_skb+0x41c/0xb58
[ 614.486513] tcp_write_xmit+0x224/0x10a0
[ 614.498792] __tcp_push_pending_frames+0x38/0xc8
[ 614.513126] tcp_rcv_established+0x41c/0x820
[ 614.526301] tcp_v4_do_rcv+0x8c/0x218
[ 614.537784] __release_sock+0x5c/0x108
[ 614.549466] release_sock+0x34/0xa0
[ 614.560318] tcp_sendmsg+0x40/0x58
[ 614.571053] inet_sendmsg+0x40/0x68
[ 614.582061] sock_sendmsg+0x18/0x30
[ 614.593074] xs_sendpages+0x218/0x328
[ 614.604506] xs_tcp_send_request+0xa0/0x1b8
[ 614.617461] xprt_transmit+0xc8/0x4f0
[ 614.628943] call_transmit+0x8c/0xa0
[ 614.640028] __rpc_execute+0xbc/0x6f8
[ 614.651380] rpc_async_schedule+0x28/0x48
[ 614.663846] process_one_work+0x298/0x6a8
[ 614.676299] worker_thread+0x40/0x490
[ 614.687687] kthread+0x134/0x138
[ 614.697804] ret_from_fork+0x10/0x18
[ 614.717319] xilinx_axienet 7fe00000.ethernet eth0: Link is Down
[ 615.748343] xilinx_axienet 7fe00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off

Since tasklets are not really popular anymore anyway, lets convert this
over to a work queue, which can sleep and thus can take the MDIO mutex.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: let core reject the unsupported coalescing parameters

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver already correctly rejected all unsupported
parameters. No functional changes.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: use resolved link config in mac_link_up()

Convert the Xilinx AXI ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().

Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phylink: propagate resolved link config via mac_link_up()

Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.

Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phylink: rename mac_link_state() op to mac_pcs_get_state()

Rename the mac_link_state() method to mac_pcs_get_state() to make it
clear that it should be returning the MACs PCS current state, which
is used for inband negotiation rather than just reading back what the
MAC has been configured for. Update the documentation to explicitly
mention that this is for inband.

We drop the return value as well; most of phylink doesn't check the
return value and it is not clear what it should do on error - instead
arrange for state->link to be false.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: axienet: Fix error return code in axienet_probe()

In the DMA memory resource get failed case, the error is not
set and 0 will be returned. Fix it by removing redundant check
since devm_ioremap_resource() will handle it.

Fixes: 28ef9ebdb64c ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: of_get_phy_mode: Change API to solve int/unit warnings

Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.

Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.

v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees

v3:
Fix 0-day reported errors.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: fix a signedness bug in probe

The "lp->phy_mode" is an enum but in this context GCC treats it as an
unsigned int so the error handling is never triggered.

Fixes: ee06b1728b95 ("net: axienet: add support for standard phy-mode binding")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: fix a potential double free in axienet_probe()

There is a possible use-after-free issue in the axienet_probe():

1701: np = of_parse_phandle(pdev->dev.of_node, "axistream-connected", 0);
1702: if (np) {
...
1787: of_node_put(np); ---> released here
1788: lp->eth_irq = platform_get_irq(pdev, 0);
1789: } else {
...
1801: }
1802: if (IS_ERR(lp->dma_regs)) {
...
1805: of_node_put(np); ---> double released here
1806: goto free_netdev;
1807: }

We solve this problem by removing the unnecessary of_node_put().

Fixes: 28ef9ebdb64c ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Robert Hancock <hancock@sedsystems.ca>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: move use of resource after validity check

We were accessing the pointer returned from platform_get_resource before
checking if it was valid, causing an oops if it was not. Move this access
after the call to devm_ioremap_resource which does the validity check.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: convert to phylink API

Convert this driver to use the phylink API rather than the legacy PHY
API. This allows for better support for SFP modules connected using a
1000BaseX or SGMII interface.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: make use of axistream-connected attribute optional

Currently the axienet driver requires the use of a second devicetree
node, referenced by an axistream-connected attribute on the Ethernet
device node, which contains the resources for the AXI DMA block used by the
device. This setup is problematic for a use case we have where the Ethernet
and DMA cores are behind a PCIe to AXI bridge and the memory resources for
the nodes are injected into the platform devices using the multifunction
device subsystem - it's not easily possible for the driver to obtain the
platform-level resources from the linked device.

In order to simplify that usage model, and simplify the overall use of
this driver in general, allow for all of the resources to be kept on one
node where the resources are retrieved using platform device APIs rather
than device-tree-specific ones. The previous usage setup is still
supported if the axistream-connected attribute is specified.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: stop interface during shutdown

On some platforms, such as iMX6 with PCIe devices, crashes or hangs can
occur if the axienet device continues to perform DMA transfers after
parent devices/busses have been shut down. Shut down the axienet
interface during its shutdown callback in order to avoid this.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Make missing MAC address non-fatal

Failing initialization on a missing MAC address property is excessive.
We can just fall back to using a random MAC instead, which at least
leaves the interface in a functioning state.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix race condition causing TX hang

It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in axienet_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.

To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Add optional support for Ethernet core interrupt

Previously this driver only handled interrupts from the DMA RX and TX
blocks, not from the Ethernet core itself. Add optional support for
the Ethernet core interrupt, which is used to detect rx_missed and
framing errors signalled by the hardware. In order to use this
interrupt, a third interrupt needs to be specified in the device tree.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Support shared interrupts

Specify IRQF_SHARED to support shared interrupts. If the interrupt
handler is called and the device is not indicating an interrupt,
just return IRQ_NONE rather than spewing error messages.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Add DMA registers to ethtool register dump

These registers are important for troubleshooting the state of the DMA
cores.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Make RX/TX ring sizes configurable

Add support for setting the RX and TX ring sizes for this driver using
ethtool. Also increase the default RX ring size as the previous default
was far too low for good performance in some configurations.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Cleanup DMA device reset and halt process

The Xilinx DMA blocks each have their own reset register, but they both
reset the entire DMA engine, so only one of them needs to be reset.

Also, when stopping the device, we need to not just command the DMA
blocks to stop, but wait for them to stop, and trigger a device reset
to ensure that they are completely stopped.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Re-initialize MDIO registers properly after reset

The MDIO clock divisor register setting was only applied on the initial
startup when the driver was loaded. However, this setting is cleared
when the device is reset, such as would occur when the interface was
taken down and brought up again, and so the MDIO bus would be
non-functional afterwards.

Split up the MDIO bus setup and enable into separate functions and
re-enable the bus after a device reset, to ensure that the MDIO
registers are set properly. This also allows us to remove direct access
to MDIO registers in xilinx_axienet_main.c and centralize them all in
xilinx_axienet_mdio.c.

Also, lock the MDIO bus lock around the device reset process, to avoid
MDIO accesses from occurring while the MDIO is disabled during the reset.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: fix teardown order of MDIO bus

Since the MDIO is is brought up before the netdev is registered, it
should be torn down after the netdev is removed. Otherwise, PHY accesses
can potentially access freed MDIO bus references and cause a crash.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Use clock framework to get device clock rate

This driver was previously always calculating the MDIO clock divisor
(from AXI bus clock to MDIO bus clock) based on the CPU clock frequency,
assuming that it is the same as the AXI bus frequency, but that
simplistic method only works on the MicroBlaze platform.

Add support for specifying the clock used for the device in the device
tree using the clock framework. If the clock is specified then it will
be used when calculating the clock divisor. The previous CPU clock
detection method is left for backward compatibility if no clock is
specified.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: fix MDIO bus naming

The MDIO bus for this driver was being named using the result of
of_address_to_resource on a node which may not have any resource on it,
but the return value of that call was not checked so it was using some
random value in the bus name. Change to name the MDIO bus based on the
resource start of the actual Ethernet register block.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Use standard IO accessors

This driver was using in_be32 and out_be32 IO accessors which do not
exist on most platforms. Also, the use of big-endian accessors does not
seem correct as this hardware is accessed over an AXI bus which, to the
extent it has an endian-ness, is little-endian. Switch to standard
ioread32/iowrite32 accessors.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix casting of pointers to u32

This driver was casting skb pointers to u32 and storing them as such in
the DMA buffer descriptor, which is obviously broken on 64-bit. The area
of the buffer descriptor being used is not accessed by the hardware and
has sufficient room for a 32 or 64-bit pointer, so just store the skb
pointer as such.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

treewide: Add SPDX license identifier for more missed files

Add SPDX license identifiers to all files which:

- Have no license information of any form

- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ethernet: support of_get_mac_address new ERR_PTR error

There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.

While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.

Fixes: d01f449c008a ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: xilinx: fix possible object reference leak

The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1624:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1569, but without a corresponding object release within this function.

Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

net: xilinx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles

dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.

Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

cross-tree: phase out dma_zalloc_coherent()

We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.

This change was generated with the following Coccinelle SmPL patch:

@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@

-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)

Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>

net: xilinx: fix return type of ndo_start_xmit function

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: remove stale comment of axienet_open

axienet_open no longer return -ENODEV when PHY cannot be connected to
since commit d7cc3163e026 ("net: axienet: Support phy-less mode of operation")

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: add support for standard phy-mode binding

Keep supporting proprietary "xlnx,phy-type" attribute and add support for
MII connectivity to the PHY.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: use eth_hw_addr_random()

Use eth_hw_addr_random() to set a random MAC address in order to make
sure ndev->addr_assign_type will be properly set to NET_ADDR_RANDOM.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Utilize of_get_mac_address()

Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.

Also avoid casting away the const qualifier of the return value by
making axienet_set_mac_address() take a const void* address.

Follows commit b34296a9c047 ("net: ethoc: Utilize
of_get_mac_address()").

Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet: use net core MTU range checking in more drivers

Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.

acenic:
- min_mtu = 0, max_mtu = 9000

amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu

amd/xgbe:
- min_mtu = 0, max_mtu = 9000

sb1250:
- min_mtu = 0, max_mtu = 1518

cxgb3:
- min_mtu = 81, max_mtu = 65535

cxgb4:
- min_mtu = 81, max_mtu = 9600

cxgb4vf:
- min_mtu = 81, max_mtu = 65535

benet:
- min_mtu = 256, max_mtu = 9000

ibmveth:
- min_mtu = 68, max_mtu = 65535

ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu

jme:
- min_mtu = 1280, max_mtu = 9202

mv643xx_eth:
- min_mtu = 64, max_mtu = 9500

mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions

ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500

netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)

qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000

qualcomm/emac:
- min_mtu = 46, max_mtu = 9194

xilinx_axienet:
- min_mtu = 64, max_mtu = 9000

Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Remove unused parameter from __axienet_device_reset

The dev parameter passed to __axienet_device_reset() is not used inside
the function, so remove it.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Add missing \n to end of dev_err messages

Trival fix, dev_err messages are missing a \n, so add it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: constify ethtool_ops structures

Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };

@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;

@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)

@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>

Suggested-by: Stephen Hemminger <stephen@networkplumber.org>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix return value check in axienet_probe()

In case of error, the function of_parse_phandle() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.

Fixes: 46aa27df8853 ('net: axienet: Use devm_* calls')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: xilinx: axienet: use phy_ethtool_{get|set}_link_ksettings

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: xilinx: axienet: use phydev from struct net_device

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

treewide: replace dev->trans_start update with helper

Replace all trans_start updates with netif_trans_update helper.
change was done via spatch:

struct net_device *d;
@@
- d->trans_start = jiffies
+ netif_trans_update(d)

Compile tested only.

Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: linux-xtensa@linux-xtensa.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net: get rid of unnecessary initializations in .get_drvinfo()

Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().

v2: removed unused variable
v3: removed another unused variable

Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix devm_ioremap_resource return value check

Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes: 46aa27df8853 ("net: axienet: Use devm_* calls")
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix kernel-doc warnings

This patch remove kernel-doc warnings.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Removed _of_ prefix in probe and remove functions

Synchronize names with other drivers.

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Use of_property_* calls

Use of_property_* calls

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Use devm_* calls

use devm_* calls

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Use pdev instead of op

Synchronize names with other drivers

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix comments blocks

There is rule for network drivers with comments blocks
which is newly checked by checkpatch.pl script.
Let's fix it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Removed coding style errors and warnings

Removed checkpatch.pl errors and warnings.

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Support phy-less mode of operation

This patch adds proper checks to handle the PHY-less case.

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Handle jumbo frames for lesser frame sizes

In the current implementation, jumbo frames are supported only
for the frame sizes > 16K. This patch corrects this logic to
handle jumbo frames for lesser frame sizes (< 16K) ensuring jumbo frame
MTU is within the limit of max frame size configured in the h/w
design.

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Service completion interrupts ASAP

The packet completion interrupts for TX and RX should be serviced before
the packets are consumed. This ensures against the degenerate case when a
new completion interrupt is raised after the handler has exited but before
the interrupts are cleared. In this case its possible for the ISR to clear
an unhandled interrupt (leading to potential deadlock).

Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Jason Wu <huanyu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Handle 0 packet receive gracefully

The AXI-DMA rx-delay interrupt can sometimes be triggered
when there are 0 outstanding packets received. This is due
to the fact that the receive function will greedily consume
as many packets as possible on interrupt. So if two packets
(with a very particular timing) arrive in succession they
will each cause the rx-delay interrupt, but the first interrupt
will consume both packets.
This means the second interrupt is a 0 packet receive.

This is mostly OK, except that the tail pointer register is
updated unconditionally on receive. Currently the tail pointer
is always set to the current bd-ring descriptor under
the assumption that the hardware has moved onto the next
descriptor. What this means for length 0 recv is the current
descriptor that the hardware is potentially yet to use will
be marked as the tail. This causes the hardware to think
its run out of descriptors deadlocking the whole rx path.

Fixed by updating the tail pointer to the most recent
successfully consumed descriptor.

Reported-by: Wendy Liang <wendy.liang@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Jason Wu <huanyu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Support for RGMII

This patch adds support for the RGMII. The h/w configuration
parameter C_PHY_TYPE, which represents the interface configured in
the design, is used to differentiate various interfaces supported
by AXI Ethernet.

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: xilinx: constify of_device_id array

of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: fix error return code

Return a negative error code on failure.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: xilinx: Remove unnecessary temac_property in the driver

This property is no longer used in the code yet the code looks for it in the device tree.
It does not cause an error if it's not in the tree.

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: remove unnecessary ether_setup after alloc_etherdev

calling ether_setup is redundant since alloc_etherdev calls
it.

Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: xilinx: Remove .owner field for driver

There is no need to init .owner field.

Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"

This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: delete unneeded test before of_node_put

Of_node_put supports NULL as its argument, so the initial test is not
necessary.

Suggested by Uwe Kleine-König.

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e;
@@

-if (e)
of_node_put(e);
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xilinx: Convert uses of __constant_<foo> to <foo>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix compilation warnings

Warning log:
xilinx_axienet_main.c: In function 'axienet_start_xmit_done':
xilinx_axienet_main.c:617:16: warning: operation on 'lp->tx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_start_xmit':
xilinx_axienet_main.c:703:18: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c:719:17: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_recv':
xilinx_axienet_main.c:792:16: warning: operation on 'lp->rx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_of_probe':
xilinx_axienet_main.c:1501:21: warning: unused variable 'rc' [-Wunused-variable]

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: axienet: Fix compilation error

Add missing header to fix compilation error.
drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1575:22:
error: undefined identifier 'irq_of_parse_and_map'
drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1576:22:
error: undefined identifier 'irq_of_parse_and_map'

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net: delete non-required instances of include <linux/init.h>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

This covers everything under drivers/net except for wireless, which
has been submitted separately.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: do not pretend FRAGLIST support

Few network drivers really supports frag_list : virtual drivers.

Some drivers wrongly advertise NETIF_F_FRAGLIST feature.

If skb with a frag_list is given to them, packet on the wire will be
corrupt.

Remove this flag, as core networking stack will make sure to
provide packets that can be sent without corruption.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers:net: Convert dma_alloc_coherent(...__GFP_ZERO) to dma_zalloc_coherent

__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.

Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.

Trivially reduces the size of the existing uses of
dma_zalloc_coherent.

Realign arguments as appropriate.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: use platform_{get,set}_drvdata()

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers:net: dma_alloc_coherent: use __GFP_ZERO instead of memset(, 0)

Reduce the number of calls required to alloc
a zeroed block of memory.

Trivially reduces overall object size.

Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers:net: Remove dma_alloc_coherent OOM messages

I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.

Remove the unnecessary additional error logging.

Around these deletions:

o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers:net: Remove unnecessary OOM messages after netdev_alloc_skb

Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.

Other trivial changes around these removals:

Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: xilinx: Do not use NO_IRQ in axienet

This driver is used on Microblaze and will be used
on Arm Zynq.
Microblaze doesn't define NO_IRQ and no IRQ is 0.
Arm still uses NO_IRQ as -1 and there is no option
to connect IRQ to irq 0.

That's why <= 0 is only one option how to find out
undefined IRQ.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: fix drvinfo strings set in drivers

Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

xilinx_axienet: remove __dev* attributes

CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: fix build failure in xilinx

Commit 71c6c837 (drivers/net: fix tasklet misuse issue) introduced a
build failure in the xilinx driver. axienet_dma_err_handler isn't
declared before its use in axienet_open.

This patch provides the prototype before axienet_open.

Cc: Xiaotian Feng <dannyfeng@tencent.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net: fix tasklet misuse issue

In commit 175c0dff, drivers uses tasklet_kill to avoid put disabled tasklet
on the tasklet vec. But some of the drivers uses tasklet_init & tasklet_disable
in the driver init code, then tasklet_enable when it is opened. This makes
tasklet_enable on a killed tasklet and make ksoftirqd crazy then. Normally,
drivers should use tasklet_init/tasklet_kill on device open/remove, and use
tasklet_disable/tasklet_enable on device suspend/resume.

Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net: use tasklet_kill in device remove/close process

Some driver uses tasklet_disable in device remove/close process,
tasklet_disable will inc tasklet->count and return. If the tasklet
is not handled yet because some softirq pressure, the tasklet will
placed on the tasklet_vec, never have a chance to excute. This might
lead to ksoftirqd heavy loaded, wakeup with pending_softirq, but
tasklet is disabled. tasklet_kill should be used in this case.

Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet: Use eth_random_addr

Convert the existing uses of random_ether_addr to
the new eth_random_addr.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/xilinx/axi ethernet: Correct Copyright

Also fix MAINTAINERS file to reflect autorship.

Daniel and Ariane changed coding style but not any functional changes in the driver
itself.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: xilinx: Convert xilinx_axienet to module_platform_driver

Follow commit db62f684. Convert the driver to use the
module_platform_driver() macro which makes the code a bit smaller and
simpler.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net: Remove alloc_etherdev error messages

alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver

This driver adds support for Xilinx 10/100/1000 AXI Ethernet.

It can be used, for instance, on Xilinx boards with a Microblaze
architecture like the ML605.

The patch is against the latest net-next tree and checkpatch clean.

Signed-off-by: Ariane Keller <ariane.keller@tik.ee.ethz.ch>
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>