net: ethernet: ti: convert to SPDX license identifiers

Replace textual license with SPDX-License-Identifier.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: cpsw: deprecate cpsw-phy-sel driver

Deprecate cpsw-phy-sel driver as it's been replaced with new
TI phy-gmii-sel PHY driver.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

net: ethernet: ti: cpsw: move mac_hi/lo defines in cpsw.h

Move mac_hi/lo defines in common header cpsw.h and re-use
them for netcp_ethss.c.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: cpsw: move platform data struct to .c file

CPSW platform data struct cpsw_platform_data and struct cpsw_slave_data are
used only incide cpsw.c module, so move these definitions there.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: cpts: move dt props parsing to cpts driver

Move DT properties parsing into CPTS driver to simplify CPSW
code and CPTS driver porting on other SoC in the future
(like Keystone 2) - with this change it will not be required
to add the same DT parsing code in Keystone 2 NETCP driver.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: cpsw: remove rx_descs property

There is no reason in rx_descs property because davinici_cpdma
driver splits pool of descriptors equally between tx and rx channels.
That is, if number of descriptors 256, 128 of them are for rx
channels. While receiving, the descriptor is freed to the pool and
then allocated with new skb. And if in DT the "rx_descs" is set to
64, then 128 - 64 = 64 descriptors are always in the pool and cannot
be used, for tx, for instance. It's not correct resource usage,
better to set it to half of pool, then the rx pool can be used in
full. It will not have any impact on performance, as anyway, the
"redundant" descriptors were unused.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers: net: cpsw: fix parsing of phy-handle DT property in dual_emac config

Commit 9e42f715264ff158478fa30eaed847f6e131366b ("drivers: net: cpsw: add
phy-handle parsing") saved the "phy-handle" phandle into a new cpsw_priv
field. However, phy connections are per-slave, so the phy_node field should
be in cpsw_slave_data rather than cpsw_priv.

This would go unnoticed in a single emac configuration. But in dual_emac
mode, the last "phy-handle" property parsed for either slave would be used
by both of them, causing them both to refer to the same phy_device.

Fixes: 9e42f715264f ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers: net: cpsw: davinci_emac: move reading mac id to common file

Moving mac address reading from ethernet driver to common
file for better maintenance and for code reusable.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: cpsw: Add a minimal cpsw-common module for shared code

Looks like davinci_emac and cpsw can share some code although the
device registers have a different layout.

At least the code for getting the MAC address using syscon can
be shared by passing the register offset. Let's start with that
and set up a minimal shared cpsw-shared.c.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: cpsw: header, Add missing include

"MII_BUS_ID_SIZE" is defined in linux/phy.h which is not included in the
cpsw.h file.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers: net: cpsw-phy-sel: Add new driver for phy mode selection for cpsw

The cpsw currently lacks code to properly set up the hardware interface
mode on AM33xx. Other platforms might be equally affected.

Usually, the bootloader will configure the control module register, so
probably that's why such support wasn't needed in the past. In suspend
mode though, this register is modified, and so it needs reprogramming
after resume.

This patch adds a new driver in which hardware interface can configure
correct register bits when the slave is opened.

The AM33xx also has a bit for each slave to configure the RMII reference
clock direction. Setting it is now supported by a per-slave DT property.

This code path introducted by this patch is currently exclusive for
am33xx and same can be extened to various platforms via the DT compatibility
property.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers: net: cpsw: remove platform data header file of cpsw

CPSW driver no longer supports platform register as all the SoCs which has CPSW
are supporting DT only booting, so moving cpsw.h header file from platform
include to drivers/net/ethernet/ti

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>