sfc: support offloading ct(nat) action in RHS rules

If an IP address and/or L4 port for NAPT is available from a CT match,
the MAE will perform the edits; if no CT lookup has been performed for
this packet, the CT lookup did not return a match, or the matched CT
entry did not include NAPT, the action will have no effect.

Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: support TC rules which require OR-AR-CT-AR flow

When a foreign LHS rule (TC rule from a tunnel netdev which requests
conntrack lookup) matches on inner headers or enc_key_id, these matches
cannot be performed by the Outer Rule table, as the keys are only
available after the tunnel type has been identified (by the OR lookup)
and the rest of the headers parsed accordingly.
Offload such rules with an Action Rule, using the LOOKUP_CONTROL section
of the AR response to specify the conntrack and/or recirculation actions,
combined with an Outer Rule which performs only the usual Encap Match
duties.
This processing flow, as it requires two AR lookups per packet, is less
performant than OR-CT-AR, so only use it where necessary.

Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: support TC left-hand-side rules on foreign netdevs

Allow a tunnel netdevice (such as a vxlan) to offload conntrack lookups,
in much the same way as efx netdevs.
To ensure this rule does not overlap with other tunnel rules on the same
sip,dip,dport tuple, register a pseudo encap match of a new type
(EFX_TC_EM_PSEUDO_OR), which unlike PSEUDO_MASK may only be referenced
once (because an actual Outer Rule in hardware exists, although its
fw_id is not recorded in the encap match entry).

Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: add decrement ttl by offloading set ipv4 ttl actions

Offload pedit set ipv4 ttl field, where the ttl field has already been
matched and the new value is one less, by translating it to a decrement.

Co-developed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: introduce ethernet pedit set action infrastructure

Introduce the initial ethernet pedit set action infrastructure in
preparation for adding mac src and dst pedit action offloads.

Co-developed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: offload left-hand side rules for conntrack

Handle the (comparatively) simple case of a -trk rule on an efx netdev
(i.e. not a tunnel decap rule) with ct and goto chain actions.

Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: conntrack state matches in TC rules

Parse ct_state trk/est, mark and zone out of flower keys, and plumb
them through to the hardware, performing some minor translations.
Nothing can actually hit them yet as we're not offloading any DO_CT
actions.

Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: handle non-zero chain_index on TC rules

Map it to an 8-bit recirc_id for use by the hardware.
Currently nothing in the driver is offloading 'goto chain' actions,
so these rules cannot yet be hit.

Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: offload conntrack flow entries (match only) from CT zones

No handling yet for FLOW_ACTION_MANGLE (NAT or NAPT) actions.

Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: functions to register for conntrack zone offload

Bind a stub callback to the netfilter flow table.

Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: add MAE table machinery for conntrack table

Access to the connection tracking table in EF100 hardware is through
a "generic" table mechanism, whereby a firmware call at probe time
gives the driver a description of the field widths and offsets, so
that the driver can then construct key and response bitstrings at
runtime.
Probe the NIC for this information and populate the needed metadata
into a new meta_ct field of struct efx_tc_state.

Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: keep alive neighbour entries while a TC encap action is using them

When processing counter updates, if any action set using the newly
incremented counter includes an encap action, prod the corresponding
neighbouring entry to indicate to the neighbour cache that the entry
is still in use and passing traffic.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230621121504.17004-1-edward.cree@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sfc: neighbour lookup for TC encap action offload

For each neighbour we're interested in, create a struct efx_neigh_binder
object which has a list of all the encap_actions using it. When we
receive a neighbouring update (through the netevent notifier), find the
corresponding efx_neigh_binder and update all its users.
Since the actual generation of encap headers is still only a stub, the
resulting rules still get left on fallback actions.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sfc: some plumbing towards TC encap action offload

Create software objects to manage the metadata for encap actions that
can be attached to TC rules. However, since we don't yet have the
neighbouring information (needed to generate the Ethernet header),
all rules with encap actions are marked as "unready" and thus insert
the fallback action into hardware rather than actually offloading the
encapsulation action.

Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sfc: add fallback action-set-lists for TC offload

When offloading a TC encap action, the action information for the
hardware might not be "ready": if there's currently no neighbour entry
available for the destination address, we can't construct the Ethernet
header to prepend to the packet. In this case, we still offload the
flow rule, but with its action-set-list ID pointing at a "fallback"
action which simply delivers the packet to its default destination (as
though no flow rule had matched), thus allowing software TC to handle
it. Later, when we receive a neighbouring update that allows us to
construct the encap header, the rule will become "ready" and we will
update its action-set-list ID in hardware to point at the actual
offloaded actions.
This patch sets up these fallback ASLs, but does not yet use them.

Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sfc: support TC decap rules matching on enc_src_port

Allow efx_tc_encap_match entries to include a udp_sport and a
udp_sport_mask. As with enc_ip_tos, use pseudos to enforce that all
encap matches within a given <src_ip,dst_ip,udp_dport> tuple have
the same udp_sport_mask.
Note that since we use a single layer of pseudos for both fields, two
matches that differ in (say) udp_sport value aren't permitted to have
different ip_tos_mask, even though this would technically be safe.
Current userland TC does not support setting enc_src_port; this patch
was tested with an iproute2 patched to support it.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: support TC decap rules matching on enc_ip_tos

Allow efx_tc_encap_match entries to include an ip_tos and ip_tos_mask.
To avoid partially-overlapping Outer Rules (which can lead to undefined
behaviour in the hardware), store extra "pseudo" entries in our
encap_match hashtable, which are used to enforce that all Outer Rule
entries within a given <src_ip,dst_ip,udp_dport> tuple (or IPv6
equivalent) have the same ip_tos_mask.
The "direct" encap_match entry takes a reference on the "pseudo",
allowing it to be destroyed when all "direct" entries using it are
removed.
efx_tc_em_pseudo_type is an enum rather than just a bool because in
future an additional pseudo-type will be added to support Conntrack
offload.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: populate enc_ip_tos matches in MAE outer rules

Currently tc.c will block them before they get here, but following
patch will change that.
Use the extack message from efx_mae_check_encap_match_caps() instead
of writing a new one, since there's now more being fed in than just
an IP version.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: add offloading of 'foreign' TC (decap) rules

A 'foreign' rule is one for which the net_dev is not the sfc netdevice
or any of its representors. The driver registers indirect flow blocks
for tunnel netdevs so that it can offload decap rules. For example:

tc filter add dev vxlan0 parent ffff: protocol ipv4 flower \
enc_src_ip 10.1.0.2 enc_dst_ip 10.1.0.1 \
enc_key_id 1000 enc_dst_port 4789 \
action tunnel_key unset \
action mirred egress redirect dev $REPRESENTOR

When notified of a rule like this, register an encap match on the IP
and dport tuple (creating an Outer Rule table entry) and insert an MAE
action rule to perform the decapsulation and deliver to the representee.

Moved efx_tc_delete_rule() below efx_tc_flower_release_encap_match() to
avoid the need for a forward declaration.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: add code to register and unregister encap matches

Add a hashtable to detect duplicate and conflicting matches. If match
is not a duplicate, call MAE functions to add/remove it from OR table.
Calling code not added yet, so mark the new functions as unused.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: add functions to insert encap matches into the MAE

An encap match corresponds to an entry in the exact-match Outer Rule
table; the lookup response includes the encap type (protocol) allowing
the hardware to continue parsing into the inner headers.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: add notion of match on enc keys to MAE machinery

Extend the MAE caps check to validate that the hardware supports these
outer-header matches where used by the driver.
Extend efx_mae_populate_match_criteria() to fill in the outer rule ID
and VNI match fields.
Nothing yet populates these match fields, nor creates outer rules.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: support offloading TC VLAN push/pop actions to the MAE

EF100 can pop and/or push up to two VLAN tags.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230309115904.56442-1-edward.cree@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sfc: attach an MAE counter to TC actions that need it

The only actions that expect stats (that sfc HW supports) are gact shot
(drop), mirred redirect and mirred mirror. Since these are 'deliverish'
actions that end an action-set, we only require at most one counter per
action-set.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: add hashtables for MAE counters and counter ID mappings

Nothing populates them yet.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: add extra RX channel to receive MAE counter updates on ef100

Currently there is no counter-allocating machinery to connect the
resulting counter update values to; that will be added in a
subsequent patch.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: add ef100 MAE counter support functions

Start and stop MAE counter streaming, and grant credits.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: add Layer 4 matches to ef100 TC offload

Support matching on UDP/TCP source and destination ports and TCP flags,
with masking if supported by the hardware.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sfc: add Layer 3 flag matches to ef100 TC offload

Support matching on ip_frag and ip_firstfrag.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sfc: add Layer 3 matches to ef100 TC offload

Support matching on IP protocol, Type of Service, Time To Live, source
and destination addresses, with masking if supported by the hardware.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sfc: add Layer 2 matches to ef100 TC offload

Support matching on EtherType, VLANs and ethernet source/destination
addresses, with masking if supported by the hardware.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sfc: use formatted extacks instead of efx_tc_err()

Since we can now get a formatted message back to the user with
NL_SET_ERR_MSG_FMT_MOD(), there's no need for our special logging.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sfc: bare bones TC offload on EF100

This is the absolute minimum viable TC implementation to get traffic to
VFs and allow them to be tested; it supports no match fields besides
ingress port, no actions besides mirred and drop, and no stats.
Example usage:
tc filter add dev $PF parent ffff: flower skip_sw \
action mirred egress mirror dev $VFREP
tc filter add dev $VFREP parent ffff: flower skip_sw \
action mirred egress redirect dev $PF
gives a VF unfiltered access to the network out the physical port ($PF
acts here as a physical port representor).
More matches, actions, and counters will be added in subsequent patches.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: interrogate MAE capabilities at probe time

Different versions of EF100 firmware and FPGA bitstreams support different
matching capabilities in the Match-Action Engine. Probe for these at
start of day; subsequent patches will validate TC offload requests
against the reported capabilities.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: add a hashtable for offloaded TC rules

Nothing inserts into this table yet, but we have code to remove rules
on FLOW_CLS_DESTROY or at driver teardown time, in both cases also
attempting to remove the corresponding hardware rules.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: optional logging of TC offload errors

TC offload support will involve complex limitations on what matches and
actions a rule can do, in some cases potentially depending on rules
already offloaded. So add an ethtool private flag "log-tc-errors" which
controls reporting the reasons for un-offloadable TC rules at NETIF_INFO.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: bind blocks for TC offload on EF100

Bind direct blocks for the MAE-admin PF and each VF representor.
Currently these connect to a stub efx_tc_flower() that only returns
-EOPNOTSUPP; subsequent patches will implement flower offloads to the
Match-Action Engine.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: use a dynamic m-port for representor RX and set it promisc

Representors do not want to be subject to the PF's Ethernet address
filters, since traffic from VFs will typically have a destination
either elsewhere on the link segment or on an overlay network.
So, create a dynamic m-port with promiscuous and all-multicast
filters, and set it as the egress port of representor default rules.
Since the m-port is an alias of the calling PF's own m-port, traffic
will still be delivered to the PF's RXQs, but it will be subject to
the VNRX filter rules installed on the dynamic m-port (specified by
the v-port ID field of the filter spec).

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sfc: insert default MAE rules to connect VFs to representors

Default rules are low-priority switching rules which the hardware uses
in the absence of higher-priority rules. Each representor requires a
corresponding rule matching traffic from its representee VF and
delivering to the PF (where a check on INGRESS_MPORT in
__ef100_rx_packet() will direct it to the representor). No rule is
required in the reverse direction, because representor TX uses a TX
override descriptor to bypass the MAE and deliver directly to the VF.
Since inserting any rule into the MAE disables the firmware's own
default rules, also insert a pair of rules to connect the PF to the
physical network port and vice-versa.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>