qede: fix firmware halt over suspend and resume

While performing certain power-off sequences, PCI drivers are
called to suspend and resume their underlying devices through
PCI PM (power management) interface. However this NIC hardware
does not support PCI PM suspend/resume operations so system wide
suspend/resume leads to bad MFW (management firmware) state which
causes various follow-up errors in driver when communicating with
the device/firmware afterwards.

To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding
system to go into suspended/standby mode.

Without this fix device/firmware does not recover unless system
is power cycled.

Fixes: 2950219d87b0 ("qede: Add basic network device support")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230816150711.59035-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

qed/qede: Fix scheduling while atomic

Statistics read through bond interface via sysfs causes
below bug and traces as it triggers the bonding module to
collect the slave device statistics while holding the spinlock,
beneath that qede->qed driver statistics flow gets scheduled out
due to usleep_range() used in PTT acquire logic

[ 3673.988874] Hardware name: HPE ProLiant DL365 Gen10 Plus/ProLiant DL365 Gen10 Plus, BIOS A42 10/29/2021
[ 3673.988878] Call Trace:
[ 3673.988891] dump_stack_lvl+0x34/0x44
[ 3673.988908] __schedule_bug.cold+0x47/0x53
[ 3673.988918] __schedule+0x3fb/0x560
[ 3673.988929] schedule+0x43/0xb0
[ 3673.988932] schedule_hrtimeout_range_clock+0xbf/0x1b0
[ 3673.988937] ? __hrtimer_init+0xc0/0xc0
[ 3673.988950] usleep_range+0x5e/0x80
[ 3673.988955] qed_ptt_acquire+0x2b/0xd0 [qed]
[ 3673.988981] _qed_get_vport_stats+0x141/0x240 [qed]
[ 3673.989001] qed_get_vport_stats+0x18/0x80 [qed]
[ 3673.989016] qede_fill_by_demand_stats+0x37/0x400 [qede]
[ 3673.989028] qede_get_stats64+0x19/0xe0 [qede]
[ 3673.989034] dev_get_stats+0x5c/0xc0
[ 3673.989045] netstat_show.constprop.0+0x52/0xb0
[ 3673.989055] dev_attr_show+0x19/0x40
[ 3673.989065] sysfs_kf_seq_show+0x9b/0xf0
[ 3673.989076] seq_read_iter+0x120/0x4b0
[ 3673.989087] new_sync_read+0x118/0x1a0
[ 3673.989095] vfs_read+0xf3/0x180
[ 3673.989099] ksys_read+0x5f/0xe0
[ 3673.989102] do_syscall_64+0x3b/0x90
[ 3673.989109] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 3673.989115] RIP: 0033:0x7f8467d0b082
[ 3673.989119] Code: c0 e9 b2 fe ff ff 50 48 8d 3d ca 05 08 00 e8 35 e7 01 00 0f 1f 44 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 0f 05 <48> 3d 00 f0 ff ff 77 56 c3 0f 1f 44 00 00 48 83 ec 28 48 89 54 24
[ 3673.989121] RSP: 002b:00007ffffb21fd08 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[ 3673.989127] RAX: ffffffffffffffda RBX: 000000000100eca0 RCX: 00007f8467d0b082
[ 3673.989128] RDX: 00000000000003ff RSI: 00007ffffb21fdc0 RDI: 0000000000000003
[ 3673.989130] RBP: 00007f8467b96028 R08: 0000000000000010 R09: 00007ffffb21ec00
[ 3673.989132] R10: 00007ffffb27b170 R11: 0000000000000246 R12: 00000000000000f0
[ 3673.989134] R13: 0000000000000003 R14: 00007f8467b92000 R15: 0000000000045a05
[ 3673.989139] CPU: 30 PID: 285188 Comm: read_all Kdump: loaded Tainted: G W OE

Fix this by collecting the statistics asynchronously from a periodic
delayed work scheduled at default stats coalescing interval and return
the recent copy of statisitcs from .ndo_get_stats64(), also add ability
to configure/retrieve stats coalescing interval using below commands -

ethtool -C ethx stats-block-usecs <val>
ethtool -c ethx

Fixes: 133fac0eedc3 ("qede: Add basic ethtool support")
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Link: https://lore.kernel.org/r/20230605112600.48238-1-manishc@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: qede: Remove unnecessary aer.h include

<linux/aer.h> is unused, so remove it.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

qede: avoid uninitialized entries in coal_entry array

Even after commit 908d4bb7c54c ("qede: fix interrupt coalescing
configuration"), some entries of the coal_entry array may theoretically
be used uninitialized:

1. qede_alloc_fp_array() allocates QEDE_MAX_RSS_CNT entries for
coal_entry. The initial allocation uses kcalloc, so everything is
initialized.
2. The user sets a small number of queues (ethtool -L).
coal_entry is reallocated for the actual small number of queues.
3. The user sets a bigger number of queues.
coal_entry is reallocated bigger. The added entries are not
necessarily initialized.

In practice, the reallocations will actually keep using the originally
allocated region of memory, but we should not rely on it.

The reallocation is unnecessary. coal_entry can always have
QEDE_MAX_RSS_CNT entries.

Fixes: 908d4bb7c54c ("qede: fix interrupt coalescing configuration")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Nacked-by: Manish Chopra <manishc@marvell.com>
Acked-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: fix interrupt coalescing configuration

On default driver load device gets configured with unexpected
higher interrupt coalescing values instead of default expected
values as memory allocated from krealloc() is not supposed to
be zeroed out and may contain garbage values.

Fix this by allocating the memory of required size first with
kcalloc() and then use krealloc() to resize and preserve the
contents across down/up of the interface.

Signed-off-by: Manish Chopra <manishc@marvell.com>
Fixes: b0ec5489c480 ("qede: preserve per queue stats across up/down of interface")
Cc: stable@vger.kernel.org
Cc: Bhaskar Upadhaya <bupadhaya@marvell.com>
Cc: David S. Miller <davem@davemloft.net>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2160054
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers: net: turn on XDP features

A summary of the flags being set for various drivers is given below.
Note that XDP_F_REDIRECT_TARGET and XDP_F_FRAG_TARGET are features
that can be turned off and on at runtime. This means that these flags
may be set and unset under RTNL lock protection by the driver. Hence,
READ_ONCE must be used by code loading the flag value.

Also, these flags are not used for synchronization against the availability
of XDP resources on a device. It is merely a hint, and hence the read
may race with the actual teardown of XDP resources on the device. This
may change in the future, e.g. operations taking a reference on the XDP
resources of the driver, and in turn inhibiting turning off this flag.
However, for now, it can only be used as a hint to check whether device
supports becoming a redirection target.

Turn 'hw-offload' feature flag on for:
- netronome (nfp)
- netdevsim.

Turn 'native' and 'zerocopy' features flags on for:
- intel (i40e, ice, ixgbe, igc)
- mellanox (mlx5).
- stmmac
- netronome (nfp)

Turn 'native' features flags on for:
- amazon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2, enetc)
- funeth
- intel (igb)
- marvell (mvneta, mvpp2, octeontx2)
- mellanox (mlx4)
- mtk_eth_soc
- qlogic (qede)
- sfc
- socionext (netsec)
- ti (cpsw)
- tap
- tsnep
- veth
- xen
- virtio_net.

Turn 'basic' (tx, pass, aborted and drop) features flags on for:
- netronome (nfp)
- cavium (thunder)
- hyperv.

Turn 'redirect_target' feature flag on for:
- amanzon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2)
- intel (i40e, ice, igb, ixgbe)
- ti (cpsw)
- marvell (mvneta, mvpp2)
- sfc
- socionext (netsec)
- qlogic (qede)
- mellanox (mlx5)
- tap
- veth
- virtio_net
- xen

Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Marek Majtyka <alardam@gmail.com>
Link: https://lore.kernel.org/r/3eca9fafb308462f7edb1f58e451d59209aa07eb.1675245258.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

net: drop the weight argument from netif_napi_add

We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().

Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: move from strlcpy with unused retval to strscpy

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: qede: Remove unnecessary synchronize_irq() before free_irq()

Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220516082251.1651350-1-chi.minghao@zte.com.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

qed*: enhance tx timeout debug info

This patch add some new qed APIs to query status block
info and report various data to MFW on tx timeout event

Along with that it enhances qede to dump more debug logs
(not just specific to the queue which was reported by stack)
on tx timeout which includes various other basic metadata about
all tx queues and other info (like status block etc.)

Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

qed: Remove e4_ and _e4 from FW HSI

The existing qed/qede/qedr/qedi/qedf code uses chip-specific naming in
structures, functions, variables and defines in FW HSI (Hardware
Software Interface).

The new FW version introduced a generic naming convention in HSI
in-which the same code will be used across different versions
for simpler maintainability. It also eases in providing support for
new features.

With this patch every "_e4" or "e4_" prefix or suffix is not needed
anymore and it will be removed.

Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Fix kernel-doc warnings

This patch fixes all the qed and qede kernel-doc warnings
according to the guidelines that are described in
Documentation/doc-guide/kernel-doc.rst.

Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet: use eth_hw_addr_set() instead of ether_addr_copy()

Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():

@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Don't ignore devlink allocation failures

devlink is a software interface that doesn't depend on any hardware
capabilities. The failure in SW means memory issues, wrong parameters,
programmer error e.t.c.

Like any other such interface in the kernel, the returned status of
devlink APIs should be checked and propagated further and not ignored.

Fixes: 755f982bb1ff ("qed/qede: make devlink survive recovery")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Enable automatic recovery on error condition.

This patch enables automatic recovery by default in case of various
error condition like fw assert , hardware error etc.
This also ensure driver can handle multiple iteration of assertion
conditions.

Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Remove the qede module version

Removing the qede module version which is not needed and not allowed
with inbox drivers.

Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_ioctl: split out ndo_eth_ioctl

Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.

Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.

This is a purely cosmetic change intended to help readers find
their way through the implementation.

Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix memset corruption

Thanks to Kees Cook who detected the problem of memset that starting
from not the first member, but sized for the whole struct.
The better change will be to remove the redundant memset and to clear
only the msix_cnt member.

Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: fix crash in rmmod qede while automatic debug collection

A crash has been observed if rmmod is done while automatic debug
collection in progress. It is due to a race condition between
both of them.

To fix stop the sp_task during unload to avoid running qede_sp_task
even if they are schedule during removal process.

Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: remove unused including <linux/version.h>

Remove including <linux/version.h> that don't need it.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: preserve per queue stats across up/down of interface

Here we do the initialization of coalescing values on load.
per queue coalesce values are also restored across up/down of
ethernet interface.

Signed-off-by: Bhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: remove ndo_udp_tunnel_* callbacks

All UDP tunnel port management is now routed via udp_tunnel_nic
infra directly. Remove the old callbacks.

Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

xsk: Propagate napi_id to XDP socket Rx path

Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.

Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com

net: qede: Disable aRFS for NPAR and 100G

In some configurations ARFS cannot be used, so disable it if device
is not capable.

Fixes: e4917d46a653 ("qede: Add aRFS support")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: make driver reliable on unload after failures

In case recovery was not successful, netdev still should be
present. But we should clear cdev if something bad happens
on recovery.

We also check cdev for null on dev close. That could be a case
if recovery was not successful.

Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: make use of devlink recovery infrastructure

Remove forcible recovery trigger and put it as a normal devlink
callback.

This allows user to enable/disable it via

devlink health set pci/0000:03:00.0 reporter fw_fatal auto_recover false

Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: use devlink logic to report errors

Use devlink_health_report to push error indications.
We implement this in qede via callback function to make it possible
to reuse the same for other drivers sitting on top of qed in future.

Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed/qede: make devlink survive recovery

Devlink instance lifecycle was linked to qed_dev object,
that caused devlink to be recreated on each recovery.

Changing it by making higher level driver (qede) responsible for its
life. This way devlink now survives recoveries.

qede now stores devlink structure pointer as a part of its device
object, devlink private data contains a linkage structure,
qed_devlink.

Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qede: use eth_zero_addr() to clear mac address

Use eth_zero_addr() to clear mac address instead of memset().

Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Use %pM format specifier for MAC addresses

Convert to %pM instead of using custom code.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: add .ndo_xdp_xmit() and XDP_REDIRECT support

Add XDP_REDIRECT case handling and the corresponding NDO to support
redirecting XDP frames. This also includes registering driver memory
model (currently order-0 page mode) in BPF subsystem.
The total number of XDP queues is usually 1:1 with Rx ones.

Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: reformat net_device_ops declarations

Correct the indentation of net_device_ops declarations for fancier look.

Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: simplify chain allocation with init params struct

To simplify qed_chain_alloc() prototype and call sites, introduce struct
qed_chain_init_params to specify chain params, and pass a pointer to
filled struct to the actual qed_chain_alloc() instead of a long list
of separate arguments.

Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: populate supported link modes maps on module init

Simplify and lighten qede_set_link_ksettings() by declaring static link
modes maps and populating them on module init. This way we save plenty
of text size at the low expense of __ro_after_init and __initconst data
(the latter will be purged after module init is done).

Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: convert to new udp_tunnel_nic infra

Covert to new infra. Looks like this driver was not doing
ref counting, and sleeping in the callback.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qede: update copyright years

Set the actual copyright holder and years in all qede source files.

Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qede: convert to SPDX License Identifiers

QLogic QED drivers source code is dual licensed under
GPL-2.0/BSD-3-Clause.
Remove all the boilerplates in the existing code and replace it with the
correct SPDX tag.

Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qede: fix use-after-free on recovery and AER handling

Set edev->cdev pointer to NULL after calling remove() callback to avoid
using of already freed object.

Fixes: ccc67ef50b90 ("qede: Error recovery process")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qede: fix PTP initialization on recovery

Currently PTP cyclecounter and timecounter are initialized only on
the first probing and are cleaned up during removal. This means that
PTP becomes non-functional after device recovery.
Fix this by unconditional PTP initialization on probing and clearing
Tx pending bit on exiting.

Fixes: ccc67ef50b90 ("qede: Error recovery process")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qed: fixes crash while running driver in kdump kernel

This fixes a crash introduced by recent is_kdump_kernel() check.
The source of the crash is that kdump kernel can be loaded on a
system with already created VFs. But for such VFs, it will follow
a logic path of PF and eventually crash.

Thus, we are partially reverting back previous changes and instead
use is_kdump_kernel is a single init point of PF init, where we
disable SRIOV explicitly.

Fixes: 37d4f8a6b41f ("net: qed: Disable SRIOV functionality inside kdump kernel")
Cc: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlogic/qede: Add XDP frame size to driver

The driver qede uses a full page, when XDP is enabled. The drivers value
in rx_buf_seg_size (struct qede_rx_queue) will be PAGE_SIZE when an
XDP bpf_prog is attached.

Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Ariel Elior <aelior@marvell.com>
Cc: GR-everest-linux-l2@marvell.com
Link: https://lore.kernel.org/bpf/158945340366.97035.7764939691580349618.stgit@firesoul

net: qede: Implement ndo_tx_timeout

Upon tx timeout detection we do disable carrier and print TX queue
info on TX timeout. We then raise hw error condition and trigger
service task to handle this.

This handler will capture extra debug info and then optionally
trigger recovery procedure to try restore function.

Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qed: attention clearing properties

On different hardware events we have to respond differently,
on some of hardware indications hw attention (error condition)
should be cleared by the driver to continue normal functioning.

Here we introduce attention clear flags, and put them on some
important events (in aeu_descs).

Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qede: add hw err scheduled handler

qede (ethernet level driver) registers a callback handler.
This handler maintains eth dev state flags/bits to track error processing.

It implements in place processing part for nonsleeping context (WARN_ON
trigger), and a deferred (delayed work) part which triggers recovery
process for recoverable errors.

In later patches this atomic handler will come with more meat.

We introduce err_flags on ethdevice structure, its being used to record
error handling properties.

Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qed: Disable SRIOV functionality inside kdump kernel

Since we have kdump kernel(s) running under severe memory constraint
it makes sense to disable the qed SRIOV functionality when running the
kdump kernel as kdump configurations on several distributions don't
support SRIOV targets for saving the vmcore (see [1] for example).

Currently the qed SRIOV functionality ends up consuming memory in
the kdump kernel, when we don't really use the same.

An example log seen in the kdump kernel with the SRIOV functionality
enabled can be seen below (obtained via memstrack tool, see [2]):
dracut-pre-pivot[676]: ======== Report format module_summary: ========
dracut-pre-pivot[676]: Module qed using 149.6MB (2394 pages), peak allocation 149.6MB (2394 pages)

This patch disables the SRIOV functionality inside kdump kernel and with
the same applied the memory consumption goes down:
dracut-pre-pivot[671]: ======== Report format module_summary: ========
dracut-pre-pivot[671]: Module qed using 124.6MB (1993 pages), peak allocation 124.7MB (1995 pages)

[1]. https://access.redhat.com/documentation/en-us/red_hat_enterprise_linux/8/html/managing_monitoring_and_updating_the_kernel/installing-and-configuring-kdump_managing-monitoring-and-updating-the-kernel#supported-kdump-targets_supported-kdump-configurations-and-targets
[2]. Memstrack tool: https://github.com/ryncsn/memstrack

Cc: kexec@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Ariel Elior <aelior@marvell.com>
Cc: GR-everest-linux-l2@marvell.com
Cc: Manish Chopra <manishc@marvell.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qed*: Reduce RX and TX default ring count when running inside kdump kernel

Normally kdump kernel(s) run under severe memory constraint with the
basic idea being to save the crashdump vmcore reliably when the primary
kernel panics/hangs.

Currently the qed* ethernet driver ends up consuming a lot of memory in
the kdump kernel, leading to kdump kernel panic when one tries to save
the vmcore via ssh/nfs (thus utilizing the services of the underlying
qed* network interfaces).

An example OOM message log seen in the kdump kernel can be seen here
[1], with crashkernel size reservation of 512M.

Using tools like memstrack (see [2]), we can track the modules taking up
the bulk of memory in the kdump kernel and organize the memory usage
output as per 'highest allocator first'. An example log for the OOM case
indicates that the qed* modules end up allocating approximately 216M
memory, which is a large part of the total crashkernel size:

dracut-pre-pivot[676]: ======== Report format module_summary: ========
dracut-pre-pivot[676]: Module qed using 149.6MB (2394 pages), peak allocation 149.6MB (2394 pages)
dracut-pre-pivot[676]: Module qede using 65.3MB (1045 pages), peak allocation 65.3MB (1045 pages)

This patch reduces the default RX and TX ring count from 1024 to 64
when running inside kdump kernel, which leads to a significant memory
saving.

An example log with the patch applied shows the reduced memory
allocation in the kdump kernel:
dracut-pre-pivot[674]: ======== Report format module_summary: ========
dracut-pre-pivot[674]: Module qed using 141.8MB (2268 pages), peak allocation 141.8MB (2268 pages)
<..snip..>
[dracut-pre-pivot[674]: Module qede using 4.8MB (76 pages), peak allocation 4.9MB (78 pages)

Tested crashdump vmcore save via ssh/nfs protocol using underlying qed*
network interface after applying this patch.

[1] OOM log:
------------

kworker/0:6: page allocation failure: order:6,
mode:0x60c0c0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null)
kworker/0:6 cpuset=/ mems_allowed=0
CPU: 0 PID: 145 Comm: kworker/0:6 Not tainted 4.18.0-109.el8.aarch64 #1
Hardware name: To be filled by O.E.M. Saber/Saber, BIOS 0ACKL025
01/18/2019
Workqueue: events work_for_cpu_fn
Call trace:
dump_backtrace+0x0/0x188
show_stack+0x24/0x30
dump_stack+0x90/0xb4
warn_alloc+0xf4/0x178
__alloc_pages_nodemask+0xcac/0xd58
alloc_pages_current+0x8c/0xf8
kmalloc_order_trace+0x38/0x108
qed_iov_alloc+0x40/0x248 [qed]
qed_resc_alloc+0x224/0x518 [qed]
qed_slowpath_start+0x254/0x928 [qed]
__qede_probe+0xf8/0x5e0 [qede]
qede_probe+0x68/0xd8 [qede]
local_pci_probe+0x44/0xa8
work_for_cpu_fn+0x20/0x30
process_one_work+0x1ac/0x3e8
worker_thread+0x44/0x448
kthread+0x130/0x138
ret_from_fork+0x10/0x18
Cannot start slowpath
qede: probe of 0000:05:00.1 failed with error -12

[2]. Memstrack tool: https://github.com/ryncsn/memstrack

Cc: kexec@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Ariel Elior <aelior@marvell.com>
Cc: GR-everest-linux-l2@marvell.com
Cc: Manish Chopra <manishc@marvell.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: qede: Use true for bool variable in qede_init_fp()

Fix the following coccicheck warning:

drivers/net/ethernet/qlogic/qede/qede_main.c:1717:5-19: WARNING:
Assignment of 0/1 to bool variable

Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add support for handling the pcie errors.

The error recovery is handled by management firmware (MFW) with the help of
qed/qede drivers. Upon detecting the errors, driver informs MFW about this
event which in turn starts a recovery process. MFW sends ERROR_RECOVERY
notification to the driver which performs the required cleanup/recovery
from the driver side.

Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Disable hardware gro when xdp prog is installed

commit 18c602dee472 ("qede: Use NETIF_F_GRO_HW.") introduced
a regression in driver that when xdp program is installed on
qede device, device's aggregation feature (hardware GRO) is not
getting disabled, which is unexpected with xdp.

Fixes: 18c602dee472 ("qede: Use NETIF_F_GRO_HW.")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: Convert bpf_prog refcnt to atomic64_t

Similarly to bpf_map's refcnt/usercnt, convert bpf_prog's refcnt to atomic64
and remove artificial 32k limit. This allows to make bpf_prog's refcounting
non-failing, simplifying logic of users of bpf_prog_add/bpf_prog_inc.

Validated compilation by running allyesconfig kernel build.

Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191117172806.2195367-3-andriin@fb.com

qede: fix NULL pointer deref in __qede_remove()

While rebooting the system with SR-IOV vfs enabled leads
to below crash due to recurrence of __qede_remove() on the VF
devices (first from .shutdown() flow of the VF itself and
another from PF's .shutdown() flow executing pci_disable_sriov())

This patch adds a safeguard in __qede_remove() flow to fix this,
so that driver doesn't attempt to remove "already removed" devices.

[ 194.360134] BUG: unable to handle kernel NULL pointer dereference at 00000000000008dc
[ 194.360227] IP: [<ffffffffc03553c4>] __qede_remove+0x24/0x130 [qede]
[ 194.360304] PGD 0
[ 194.360325] Oops: 0000 [#1] SMP
[ 194.360360] Modules linked in: tcp_lp fuse tun bridge stp llc devlink bonding ip_set nfnetlink ib_isert iscsi_target_mod ib_srpt target_core_mod ib_srp scsi_transport_srp scsi_tgt ib_ipoib ib_umad rpcrdma sunrpc rdma_ucm ib_uverbs ib_iser rdma_cm iw_cm ib_cm libiscsi scsi_transport_iscsi dell_smbios iTCO_wdt iTCO_vendor_support dell_wmi_descriptor dcdbas vfat fat pcc_cpufreq skx_edac intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd qedr ib_core pcspkr ses enclosure joydev ipmi_ssif sg i2c_i801 lpc_ich mei_me mei wmi ipmi_si ipmi_devintf ipmi_msghandler tpm_crb acpi_pad acpi_power_meter xfs libcrc32c sd_mod crc_t10dif crct10dif_generic crct10dif_pclmul crct10dif_common crc32c_intel mgag200
[ 194.361044] qede i2c_algo_bit drm_kms_helper qed syscopyarea sysfillrect nvme sysimgblt fb_sys_fops ttm nvme_core mpt3sas crc8 ptp drm pps_core ahci raid_class scsi_transport_sas libahci libata drm_panel_orientation_quirks nfit libnvdimm dm_mirror dm_region_hash dm_log dm_mod [last unloaded: ip_tables]
[ 194.361297] CPU: 51 PID: 7996 Comm: reboot Kdump: loaded Not tainted 3.10.0-1062.el7.x86_64 #1
[ 194.361359] Hardware name: Dell Inc. PowerEdge MX840c/0740HW, BIOS 2.4.6 10/15/2019
[ 194.361412] task: ffff9cea9b360000 ti: ffff9ceabebdc000 task.ti: ffff9ceabebdc000
[ 194.361463] RIP: 0010:[<ffffffffc03553c4>] [<ffffffffc03553c4>] __qede_remove+0x24/0x130 [qede]
[ 194.361534] RSP: 0018:ffff9ceabebdfac0 EFLAGS: 00010282
[ 194.361570] RAX: 0000000000000000 RBX: ffff9cd013846098 RCX: 0000000000000000
[ 194.361621] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9cd013846098
[ 194.361668] RBP: ffff9ceabebdfae8 R08: 0000000000000000 R09: 0000000000000000
[ 194.361715] R10: 00000000bfe14201 R11: ffff9ceabfe141e0 R12: 0000000000000000
[ 194.361762] R13: ffff9cd013846098 R14: 0000000000000000 R15: ffff9ceab5e48000
[ 194.361810] FS: 00007f799c02d880(0000) GS:ffff9ceacb0c0000(0000) knlGS:0000000000000000
[ 194.361865] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 194.361903] CR2: 00000000000008dc CR3: 0000001bdac76000 CR4: 00000000007607e0
[ 194.361953] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 194.362002] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 194.362051] PKRU: 55555554
[ 194.362073] Call Trace:
[ 194.362109] [<ffffffffc0355500>] qede_remove+0x10/0x20 [qede]
[ 194.362180] [<ffffffffb97d0f3e>] pci_device_remove+0x3e/0xc0
[ 194.362240] [<ffffffffb98b3c52>] __device_release_driver+0x82/0xf0
[ 194.362285] [<ffffffffb98b3ce3>] device_release_driver+0x23/0x30
[ 194.362343] [<ffffffffb97c86d4>] pci_stop_bus_device+0x84/0xa0
[ 194.362388] [<ffffffffb97c87e2>] pci_stop_and_remove_bus_device+0x12/0x20
[ 194.362450] [<ffffffffb97f153f>] pci_iov_remove_virtfn+0xaf/0x160
[ 194.362496] [<ffffffffb97f1aec>] sriov_disable+0x3c/0xf0
[ 194.362534] [<ffffffffb97f1bc3>] pci_disable_sriov+0x23/0x30
[ 194.362599] [<ffffffffc02f83c3>] qed_sriov_disable+0x5e3/0x650 [qed]
[ 194.362658] [<ffffffffb9622df6>] ? kfree+0x106/0x140
[ 194.362709] [<ffffffffc02cc0c0>] ? qed_free_stream_mem+0x70/0x90 [qed]
[ 194.362754] [<ffffffffb9622df6>] ? kfree+0x106/0x140
[ 194.362803] [<ffffffffc02cd659>] qed_slowpath_stop+0x1a9/0x1d0 [qed]
[ 194.362854] [<ffffffffc035544e>] __qede_remove+0xae/0x130 [qede]
[ 194.362904] [<ffffffffc03554e0>] qede_shutdown+0x10/0x20 [qede]
[ 194.362956] [<ffffffffb97cf90a>] pci_device_shutdown+0x3a/0x60
[ 194.363010] [<ffffffffb98b180b>] device_shutdown+0xfb/0x1f0
[ 194.363066] [<ffffffffb94b66c6>] kernel_restart_prepare+0x36/0x40
[ 194.363107] [<ffffffffb94b66e2>] kernel_restart+0x12/0x60
[ 194.363146] [<ffffffffb94b6959>] SYSC_reboot+0x229/0x260
[ 194.363196] [<ffffffffb95f200d>] ? handle_mm_fault+0x39d/0x9b0
[ 194.363253] [<ffffffffb942b621>] ? __switch_to+0x151/0x580
[ 194.363304] [<ffffffffb9b7ec28>] ? __schedule+0x448/0x9c0
[ 194.363343] [<ffffffffb94b69fe>] SyS_reboot+0xe/0x10
[ 194.363387] [<ffffffffb9b8bede>] system_call_fastpath+0x25/0x2a
[ 194.363430] Code: f9 e9 37 ff ff ff 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41 55 4c 8d af 98 00 00 00 41 54 4c 89 ef 41 89 f4 53 e8 4c e4 55 f9 <80> b8 dc 08 00 00 01 48 89 c3 4c 8d b8 c0 08 00 00 4c 8b b0 c0
[ 194.363712] RIP [<ffffffffc03553c4>] __qede_remove+0x24/0x130 [qede]
[ 194.363764] RSP <ffff9ceabebdfac0>
[ 194.363791] CR2: 00000000000008dc

Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Sudarsana Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload

And any other existing fields in this structure that refer to tc.
Specifically:

* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers: net: use flow block API

This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.

This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.

Remove tc_block_offload alias.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: flow_offload: add flow_block_cb_setup_simple()

Most drivers do the same thing to set up the flow block callbacks, this
patch adds a helper function to do this.

This preparation patch reduces the number of changes to adapt the
existing drivers to use the flow block callback API.

This new helper function takes a flow block list per-driver, which is
set to NULL until this driver list is used.

This patch also introduces the flow_block_command and
flow_block_binder_type enumerations, which are renamed to use
FLOW_BLOCK_* in follow up patches.

There are three definitions (aliases) in order to reduce the number of
updates in this patch, which go away once drivers are fully adapted to
use this flow block API.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Make two functions static

Fix sparse warning:

drivers/net/ethernet/qlogic/qede/qede_main.c:963:6:
warning: symbol 'qede_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qede/qede_main.c:969:6:
warning: symbol 'qede_unlock' was not declared. Should it be static?

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Handle infinite driver spinning for Tx timestamp.

In PTP Tx implementation, driver kept scheduling a poll thread until the
timestamp is available. In the error scenarios (e.g. app requesting the
timestamp for non-ptp packet), this thread kept waiting for the timestamp
forever. This patch add changes to report such scenario as an error and
terminate the thread. Added a timeout of 2 seconds i.e., max time to wait
for Tx timestamp. Added a stat value ptp_skip_txts for reporting the number
of packets for which Tx timestamping is skipped.

Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Change hwfn used for sb initialization

When initializing status blocks use the affined hwfn
instead of the leading one for RDMA / Storage

Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix system crash on configuring channels.

Under heavy traffic load, when changing number of channels via
ethtool (ethtool -L) which will cause interface to be reloaded,
it was observed that some packets gets transmitted on old TX
channel/queue id which doesn't really exist after the channel
configuration leads to system crash.

Add a safeguard in the driver by validating queue id through
ndo_select_queue() which is called before the ndo_start_xmit().

Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Error recovery process

This patch adds the error recovery process in the qede driver.
The process includes a partial/customized driver unload and load, which
allows it to look like a short suspend period to the kernel while
preserving the net devices' state.

Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Revert error handling changes.

This is new code and not bug fixes.

This reverts all changes added by merge commit
8fb18be93efd7292d6ee403b9f61af1008239639

Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Error recovery process

This patch adds the error recovery process in the qede driver.
The process includes a partial/customized driver unload and load, which
allows it to look like a short suspend period to the kernel while
preserving the net devices' state.

Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Register l2 queues with doorbell overflow recovery mechanism

All L2 queues funnel through this flow, so this would cover the
regular RSS queues, as well queues created for VFs, mqos queues,
xdp queues, etc.

Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Update link status only when interface is ready.

In the case of internal reload (e.g., mtu change), there could be a race
between link-up notification from mfw and the driver unload processing. In
such case kernel assumes the link is up and starts using the queues which
leads to the server crash.

Send link notification to the kernel only when driver has already requested
MFW for the link.

Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Simplify the usage of qede-flags.

The values represented by qede->flags is being used in mixed ways:
1. As 'value' at some places e.g., QEDE_FLAGS_IS_VF usage
2. As bit-mask(value) at some places e.g., QEDE_FLAGS_PTP_TX_IN_PRORGESS
usage.
This implementation pose problems in future when we want to add more flag
values e.g., overlap of the values, overflow of 64-bit storage.

Updated the implementation to go with approach (2) for qede->flags.

Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed/qede: qede_setup_tc() can be static

Fixes: 5e7baf0fcb2a ("qed/qede: Multi CoS support.")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Ingress tc flower offload (drop action) support.

The main motive of this patch is to lay down driver's
tc offload infrastructure in place.

With these changes tc can offload various supported flow
profiles (4 tuples, src-ip, dst-ip, l4 port) for the drop
action. Dropped flows statistic is a global counter for
all the offloaded flows for drop action and is populated
in ethtool statistics as common "gft_filter_drop".

Examples -

tc qdisc add dev p4p1 ingress
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp dst_ip 192.168.40.200 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto udp src_ip 192.168.40.100 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp src_ip 192.168.40.100 dst_ip 192.168.40.200 \
src_port 453 dst_port 876 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp dst_port 98 action drop

Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed/qede: Multi CoS support.

This patch adds support for tc mqprio offload,
using this different traffic classes on the adapter
can be utilized based on configured priority to tc map.

For example -

tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3

This will cause SKBs with priority 0,1,2,3 to transmit
over tc 0,1,2,3 hardware queues respectively.

Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Add link change count value to ethtool statistics display.

This patch adds driver changes for capturing the link change count in
ethtool statistics display.

Please consider applying this to "net-next".

Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Support drop action classification

With this patch, User can configure for the supported
flows to be dropped. Added a stat "gft_filter_drop"
as well to be populated in ethtool for the dropped flows.

For example -

ethtool -N p5p1 flow-type udp4 dst-port 8000 action -1
ethtool -N p5p1 flow-type tcp4 scr-ip 192.168.8.1 action -1

Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add support for populating ethernet TLVs.

This patch adds callbacks for providing the ethernet protocol driver TLVs.

Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add build_skb() support.

This patch makes use of build_skb() throughout in driver's receieve
data path [HW gro flow and non HW gro flow]. With this, driver can
build skb directly from the page segments which are already mapped
to the hardware instead of allocating new SKB via netdev_alloc_skb()
and memcpy the data which is quite costly.

This really improves performance (keeping same or slight gain in rx
throughput) in terms of CPU utilization which is significantly reduced
[almost half] in non HW gro flow where for every incoming MTU sized
packet driver had to allocate skb, memcpy headers etc. Additionally
in that flow, it also gets rid of bunch of additional overheads
[eth_get_headlen() etc.] to split headers and data in the skb.

Tested with:
system: 2 sockets, 4 cores per socket, hyperthreading, 2x4x2=16 cores
iperf [server]: iperf -s
iperf [client]: iperf -c <server_ip> -t 500 -i 10 -P 32

HW GRO off – w/o build_skb(), throughput: 36.8 Gbits/sec

Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.59 0.00 32.93 0.00 0.00 43.07 0.00 0.00 23.42

HW GRO off - with build_skb(), throughput: 36.9 Gbits/sec

Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.70 0.00 31.70 0.00 0.00 25.68 0.00 0.00 41.92

HW GRO on - w/o build_skb(), throughput: 36.9 Gbits/sec

Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.86 0.00 24.14 0.00 0.00 6.59 0.00 0.00 68.41

HW GRO on - with build_skb(), throughput: 37.5 Gbits/sec

Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.87 0.00 23.75 0.00 0.00 6.19 0.00 0.00 69.19

Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix ref-cnt usage count

Rebooting while qedr is loaded with a VLAN interface present
results in unregister_netdevice waiting for the usage count
to become free.
The fix is that rdma devices should be removed before unregistering
the netdevice, to assure all references to ndev are decreased.

Fixes: cee9fbd8e2e9 ("qede: Add qedr framework")
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Refactor mf_mode to consist of bits.

`mf_mode' field indicates the multi-partitioning mode the device is
configured to. This method doesn't scale very well, adding a new MF mode
requires going over all the existing conditions, and deciding whether those
are needed for the new mode or not.
The patch defines a set of bit-fields for modes which are derived according
to the mode info shared by the MFW and all the configuration would be made
according to those. To add a new mode, there would be a single place where
we'll need to go and choose which bits apply and which don't.

Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: fix spelling mistake: "registeration" -> "registration"

Trivial fix to spelling mistakes in DP_ERR error message text and
comments

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix qedr link update

Link updates were not reported to qedr correctly.
Leading to cases where a link could be down, but qedr
would see it as up.
In addition, once qede was loaded, link state would be up,
regardless of the actual link state.

Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xdp/qede: setup xdp_rxq_info and intro xdp_rxq_info_is_reg

The driver code qede_free_fp_array() depend on kfree() can be called
with a NULL pointer. This stems from the qede_alloc_fp_array()
function which either (kz)alloc memory for fp->txq or fp->rxq.
This also simplifies error handling code in case of memory allocation
failures, but xdp_rxq_info_unreg need to know the difference.

Introduce xdp_rxq_info_is_reg() to handle if a memory allocation fails
and detect this is the failure path by seeing that xdp_rxq_info was
not registred yet, which first happens after successful alloaction in
qede_init_fp().

Driver hook points for xdp_rxq_info:
* reg : qede_init_fp
* unreg: qede_free_fp_array

Tested on actual hardware with samples/bpf program.

V2: Driver have no proper error path for failed XDP RX-queue info reg, as
qede_init_fp() is a void function.

Cc: everest-linux-l2@cavium.com
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

qed*: HSI renaming for different types of HW

This patch renames defines and structures in the FW HSI files to allow a
distinction between different types of HW.

Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Use NETIF_F_GRO_HW.

Advertise NETIF_F_GRO_HW and set edev->gro_disable according to the
feature flag. Add qede_fix_features() to drop NETIF_F_GRO_HW if
XDP is running or MTU does not support GRO_HW or GRO is not set.
qede_change_mtu() also checks and disables GRO_HW if MTU is not
supported.

Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: xdp: make the stack take care of the tear down

Since day one of XDP drivers had to remember to free the program
on the remove path. This leads to code duplication and is error
prone. Make the stack query the installed programs on unregister
and if something is installed, remove the program. Freeing of
program attached to XDP generic is moved from free_netdev() as well.

Because the remove will now be called before notifiers are
invoked, BPF offload state of the program will not get destroyed
before uninstall.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

net: bpf: rename ndo_xdp to ndo_bpf

ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed/qede: Add setter APIs support for RX flow classification

This patch adds support for adding and deleting rx flow
classification rules. Using this user can classify RX flow
constituting of TCP/UDP 4-tuples [src_ip/dst_ip and src_port/dst_port]
to be steered on a given RX queue

Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Set rdma generic functions prefix

Rename the functions common to both iWARP and RoCE to have a prefix of
_rdma_ instead of _roce_.

Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: qede_roce.[ch] -> qede_rdma.[ch]

Once we have iWARP support, the qede portion of the qedr<->qede would
serve all the RDMA protocols - so rename the file to be appropriate
to its function.

While we're at it, we're also moving a couple of inclusions to it into
.h files and adding includes to make sure it contains all type
definitions it requires.

Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Chain support for external PBL

iWARP would require the chains to allocate/free their PBL memory
independently, so add the infrastructure to provide it externally.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: VF XDP support

This introduces 2 changes needed for XDP to be supported for VFs:

a. On VF-side, publish the NDO based on qed outputs

b. On PF-side, request qed to allocate sufficient cids per-VF
to allow the child vfs to support it

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: L2 interface to use the SB structures directly

Part of an effort of a cleaner seperation between qed and the protocol
drivers, the L2 interface is to use the SB structure for initialization
purposes opaquely.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Replace set_id() api with set_name()

Current API between qed and protocol modules allows passing an
additional private string - but it doesn't get utilized by qed
anywhere.

Clarify the API by removing it and renaming it 'set_name'.

CC: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Log probe of PCI device

Replace meaningless logged print ('Ending successfully qede probe')
with a single-liner containing interesting information about probed
device.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: qedr closure after setting state

This is benign, but it makes more sense to start the close sequence
only after changing the internal state [in case it would once care].

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Don't use an internal MAC field

Driver maintains its primary MAC in a private field which
gets updated when ndo_dev_set_mac() gets called.

However, there are flows where the primary MAC of the device can change
without said NDO being called [bond device in TLB mode configuring
slaves' addresses], resulting in a configuration where there's a mismatch
between what's apparent to user [the netdevice's value] and what's
configured in the HW [the private value].

As we don't have any real motivation of maintaining this
private field, simply remove it and start using the netdevice's
field instead.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add missing Status-block free

When destroying the datapath channels, qede doesn't notify qed of the
released status blocks which were acquired during the initialization.

Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Honor user request for Tx buffers

Driver always allocates the maximal number of tx-buffers irrespective of
actual Tx ring config.

Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Allow WoL to activate by default

When management firmware declares that the device is WoL-capable,
the default driver behavior would be to allow the management firmware
to take the decision of whether it's actually needed or not.

Problem is ethtool interface doesn't have a 'default' kind
of option, and user would see the interface WoL as disabled,
which doesn't accurately reflect the actual configuration.
More-so, if the user actually wants to explicitly disable WoL he'd have
to first enable it [otherwise ethtool would block the command].

Instead of allowing management to make the decision, enable WoL by
default on all devices capable of it.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Split PF/VF ndos.

PFs and VFs share the same structure of NDOs today,
and the VFs explicitly fails the ndo_xdp() callback stating
it doesn't support XDP.

This results in lots of:

[qede_xdp:1032(enp131s2)]VFs don't support XDP
------------[ cut here ]------------
WARNING: CPU: 4 PID: 1426 at net/core/rtnetlink.c:1637 rtnl_dump_ifinfo+0x354/0x3c0
...
Call Trace:
? __alloc_skb+0x9b/0x1d0
netlink_dump+0x122/0x290
netlink_recvmsg+0x27d/0x430
sock_recvmsg+0x3d/0x50
...

As every dump request for the VF interface info would fail due to
rtnl_xdp_fill() returning an error code.

To resolve this, introduce a subset of the NDOs meant for the VF
in a seperate structure and register that one instead for VFs,
and omit the ndo_xdp initialization.

Fixes: 40b8c45492ef ("qede: Prevent VFs from using XDP")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix XDP memory leak on unload

When (re|un)loading, Tx-queues belonging to XDP would not get freed.

Fixes: cb6aeb079294 ("qede: Add support for XDP_TX")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add support for PTP resource locking.

The patch adds necessary changes to the driver to use qed resource
locking functionality. Currently the ptp initialization is spread
between driver probe/open implementations, associated APIs are
qede_ptp_register_phc()/qede_ptp_start(). Clubbed this functionality
into single API qed_ptp_enable() to simplify the usage of qed resource
locking implementation. The new API will be invoked in the probe path.
Similarly the ptp clean-up code is moved to qede_ptp_disable() which
gets invoked in the driver unload path.

Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed/qede: Add UDP ports in bulletin board

This patch adds support for UDP ports in bulletin board
to notify UDP ports change to the VFs

Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Configure UDP ports in local context.

This patch configures UDP ports locally instead of
configuring them in deferred context which would be
helpful in synchronizing UDP ports configuration for VFs
which will be enabled in further patches.

Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed/qede: Enable tunnel offloads based on hw configuration

This patch enables tunnel feature offloads based on hw configuration
at initialization time instead of enabling them always.

Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add aRFS support

This patch adds support for aRFS for TCP and UDP
protocols with IPv4/IPv6.

Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Support XDP adjustment of headers

In case an XDP program is attached, reserve XDP_PACKET_HEADROOM
bytes at the beginning of the packet for the program to play
with.

Modify the XDP logic in the driver to fill-in the missing bits
and re-calculate offsets and length after the program has finished
running to properly reflect the current status of the packet.

We can then go and remove the limitation of not supporting XDP programs
where xdp_adjust_head is set.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add support for ingress headroom

Driver currently doesn't support any headroom; The only 'available'
space it has in the head of the buffer is due to the placement
offset.
In order to allow [later] support of XDP adjustment of headroom,
modify the the ingress flow to properly handle a scenario where
the packets would have such.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Correct XDP forward unmapping

Driver is currently using dma_unmap_single() with the address it
passed to device for the purpose of forwarding, but the XDP
transmission buffer was originally a page allocated for the rx-queue.
The mapped address is likely to differ from the original mapped
address due to the placement offset.

This difference is going to get even bigger once we support headroom.

Cache the original mapped address of the page, and use it for unmapping
of the buffer when completion arrives for the XDP forwarded packet.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Add support for QL41xxx adapters

This adds the necessary infrastructure changes for initializing
and working with the new series of QL41xxx adapaters.

It also adds 2 new PCI device-IDs to qede:
- 0x8070 for QL41xxx PFs
- 0x8090 for VFs spawning from QL41xxx PFs

Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Fix link indication race

Driver changes the link properties via communication with
the management firmware, and re-reads the resulting link status
when it receives an indication that the link has changed.
However, there are certain scenarios where such indications
might be missing, and so driver also re-reads the current link
results without attention in several places. Specifically, it
does so during load and when resetting the link.

This creates a race where driver might reflect incorrect
link status - e.g., when explicit reading of the link status is
switched by attention with the changed configuration.

Correct this flow by a lock syncronizing the handling of the
link indications [both explicit requests and attention].

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Free netdevice only after stoping slowpath

qed needs to be informed of the removal of the qede interface
prior to its actual removal, as qede has some registered callbacks
that might get called async to the removal flow.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Initialize lock and slowpath workqueue early

Need to make sure the slowpath workqueue and the qede lock
are ready for the registration of the netdevice, as once
registered there's no guarantee those wouldn't be used.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add driver support for PTP

This patch adds the driver support for,
- Registering the ptp clock functionality with the OS.
- Timestamping the Rx/Tx PTP packets.
- Ethtool callbacks related to PTP.

Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: make ndo_get_stats64 a void function

The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.

Fix all drivers with ndo_get_stats64 to have a void function.

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Add support for ndo_set_vf_trust

Trusted VFs would be allowed to receive promiscuous and
multicast promiscuous data.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: RSS indirection based on queue-handles

A step toward having qede agnostic to the queue configurations
in firmware/hardware - let the RSS indirections use queue handles
instead of actual queue indices.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Postpone reallocation until NAPI end

During Rx flow driver allocates a replacement buffer each time
it consumes an Rx buffer. Failing to do so, it would consume the
currently processed buffer and re-post it on the ring.
As a result, the Rx ring is always completely full [from driver POV].

We now allow the Rx ring to shorten by doing the re-allocations
at the end of the NAPI run. The only limitation is that we still want to
make sure each time we reallocate that we'd still have sufficient
elements in the Rx ring to guarantee that FW would be able to post
additional data and trigger an interrupt.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Change maximal number of queues

Today qede requests contexts that would suffice for 64 'whole'
combined queues [192 meant for 64 rx, tx and xdp tx queues],
but registers netdev and limits the number of queues based on
information received by qed. In turn, qed doesn't take context
into account when informing qede how many queues it can support.

This would lead to a configuration problem in case user tries
configuring >64 combined queues to interface [or >96 in case
xdp isn't enabled]. Since we don't have a mangement firware
that actually provides so many interrupt lines to a single
device we're currently safe but that's about to change soon.

The new maximum is hence changed:
- For RoCE devices, the limit would remain 64.
- For non-RoCE devices, the limit might be higher [depending
on the actual configuration of the device].
qed would start enforcing that limit in both scenarios.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Split filtering logic to its own file

This takes the various filtering logic of the driver and
moves them into their own dedicated file - qede_filter.c.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Break datapath logic into its own file

This adds a new file qede_fp.c and relocates the datapath-related
logic into it [from qede_main.c].

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Update to dual-license

Since the submission of the qedr driver, there's inconsistency
in the licensing of the various qed/qede files - some are GPLv2
and some are dual-license.
Since qedr requires dual-license and it's dependent on both,
we're updating the licensing of all qed/qede source files.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: xdp: Allow head adjustment in XDP prog

This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().

It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.

This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.

Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: use reset to set network header

Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.

Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf, xdp: drop rcu_read_lock from bpf_prog_run_xdp and move to caller

After 326fe02d1ed6 ("net/mlx4_en: protect ring->xdp_prog with rcu_read_lock"),
the rcu_read_lock() in bpf_prog_run_xdp() is superfluous, since callers
need to hold rcu_read_lock() already to make sure BPF program doesn't
get released in the background.

Thus, drop it from bpf_prog_run_xdp(), as it can otherwise be misleading.
Still keeping the bpf_prog_run_xdp() is useful as it allows for grepping
in XDP supported drivers and to keep the typecheck on the context intact.
For mlx4, this means we don't have a double rcu_read_lock() anymore. nfp can
just make use of bpf_prog_run_xdp(), too. For qede, just move rcu_read_lock()
out of the helper. When the driver gets atomic replace support, this will
move to call-sites eventually.

mlx5 needs actual fixing as it has the same issue as described already in
326fe02d1ed6 ("net/mlx4_en: protect ring->xdp_prog with rcu_read_lock"),
that is, we're under RCU bh at this time, BPF programs are released via
call_rcu(), and call_rcu() != call_rcu_bh(), so we need to properly mark
read side as programs can get xchg()'ed in mlx5e_xdp_set() without queue
reset.

Fixes: 86994156c736 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add support for XDP_TX

Add support for forwarding via XDP. Once the eBPF is attached,
driver would allocate & configure a designated transmission queue
meant solely for forwarding packets. Said queue would share the
receive-queue's interrupt line, and would have it's own Tx statistics.

Infrastructure changes required for this [spread-out through the code]:
- Determine the DMA direction of the receive buffers based on the presence
of the eBPF program.
- Turn the sw Tx ring into a union, as regular/XDP queues have different
needs for releasing resources after completion [regular requires the SKB,
XDP requires the transmitted page].

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add basic XDP support

Add support for the ndo_xdp callback. This patch would support XDP_PASS,
XDP_DROP and XDP_ABORTED commands.

This also adds a per Rx queue statistic which counts number of packets
which didn't reach the stack [due to XDP].

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Better utilize the qede_[rt]x_queue

Improve the cacheline usage of both queues by reordering -
This reduces the cachelines required for egress datapath processing
from 3 to 2 and those required by ingress datapath processing by 2.

It also changes a couple of datapath related functions that currently
require either the fastpath or the qede_dev, changing them to be based
on the tx/rx queue instead.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Don't check netdevice for rx-hash

Receive-hashing is a fixed feature, so there's no need to check
during the ingress datapath whether it's set or not.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Handle-based L2-queues.

The driver needs to maintain several FW/HW-indices for each one of
its queues. Currently, that mapping is done by the QED where it uses
an rx/tx array of so-called hw-cids, populating them whenever a new
queue is opened and clearing them upon destruction of said queues.

This maintenance is far from ideal - there's no real reason why
QED needs to maintain such a data-structure. It becomes even worse
when considering the fact that the PF's queues and its child VFs' queues
are all mapped into the same data-structure.
As a by-product, the set of parameters an interface needs to supply for
queue APIs is non-trivial, and some of the variables in the API
structures have different meaning depending on their exact place
in the configuration flow.

This patch re-organizes the way L2 queues are configured and maintained.
In short:
- Required parameters for queue init are now well-defined.
- Qed would allocate a queue-cid based on parameters.
Upon initialization success, it would return a handle to caller.
- Queue-handle would be maintained by entity requesting queue-init,
not necessarily qed.
- All further queue-APIs [update, destroy] would use the opaque
handle as reference for the queue instead of various indices.

The possible owners of such handles:
- PF queues [qede] - complete handles based on provided configuration.
- VF queues [qede] - fw-context-less handles, containing only relative
information; Only the PF-side would need the absolute indices
for configuration, so they're omitted here.
- VF queues [qed, PF-side] - complete handles based on VF initialization.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Revise state locking scheme

As qede utilizes an internal-reload sequence as result of various
configuration changes, the netif state wouldn't always accurately describe
the status of the configuration.
To compensate, we're storing an internal state of the device, which should
only be accessed under the qede_lock.

This patch fixes and improves several state/lock interactions:
- The internal state should only be checked while locked.
- While holding lock, it's preferable to check state rather than
the netdevice's state.
- The reload sequence is not 'atomic' - unload and subsequent load
are not in the same critical section.

This also add the 'locked' variant for the reload, which would later be
used by XDP - useful in the case where the correct sequence is 'lock,
check state and re-configure if good', instead of allowing the reload
itself to make the decision regarding the configurability of the device.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Refactor data-path Rx flow

Driver's NAPI poll is using a long sequence for processing ingress
packets, and it's going to get even longer once we do XDP.
Break down the main loop into a series of sub-functions to allow
better readability of the function.

While we're at it, correct the accounting of the NAPI budget -
currently we're counting only packets passed to the stack against
the budget, even in case those are actually aggregations.
After refactoring every CQE processed would be counted against the budget.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Remove 'num_tc'.

Driver currently doesn't support multi-CoS, but it contains logic
where multiple transmission queues could be theoretically manipulated.
No point in maintaining the infrastructure at the moment.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Optimize aggregation information size

Driver needs to maintain a structure per-each concurrent possible
open aggregation, but the structure storing that metadata is far from
being optimized - biggest waste in it is that there are 2 buffer metadata,
one for a replacement buffer when the aggregation begins and the other for
holding the first aggregation's buffer after it begins [as firmware might
still update it]. Those 2 can safely be united into a single metadata
structure.

struct qede_agg_info changes the following:

/* size: 120, cachelines: 2, members: 9 */
/* sum members: 114, holes: 1, sum holes: 4 */
/* padding: 2 */
/* paddings: 2, sum paddings: 8 */
/* last cacheline: 56 bytes */
-->
/* size: 48, cachelines: 1, members: 9 */
/* paddings: 1, sum paddings: 4 */
/* last cacheline: 48 bytes */

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Correctly map aggregation replacement pages

Driver allocates replacement buffers before-hand to make
sure whenever an aggregation begins there would be a replacement
for the Rx buffers, as we can't release the buffer until
aggregation is terminated and driver logic assumes the Rx rings
are always full.

For every other Rx page that's being allocated [I.e., regular]
the page is being completely mapped while for the replacement
buffers only the first portion of the page is being mapped.
This means that:
a. Once replacement buffer replenishes the regular Rx ring,
assuming there's more than a single packet on page we'd post unmapped
memory toward HW [assuming mapping is actually done in granularity
smaller than page].
b. Unmaps are being done for the entire page, which is incorrect.

Fixes: 55482edc25f06 ("qede: Add slowpath/fastpath support and enable hardware GRO")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Don't override priv_flags

Driver is now setting the ndev's priv_flags instead of adding to it,
causing pktgen failure to utilize various features due to the loss
of the IFF_TX_SKB_SHARING indication.

Fixes: 7b7e70f979e3 ("qed*: Allow unicast filtering")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Add support for WoL

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Management firmware - notifications and defaults

Management firmware is interested in various tidbits about
the driver - including the driver state & several configuration
related fields [MTU, primtary MAC, etc.].
This adds the necessray logic to update MFW with such configurations,
some of which are passed directly via qed while for others APIs
are provide so that qede would be able to later configure if needed.

This also introduces a new default configuration for MTU which would
replace the default inherited by being an ethernet device.

Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix out-of-bound fastpath memory access

Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.

To fix this, simply allocate X + 1 entries in the shadow array.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix incorrrect usage of APIs for un-mapping DMA memory

Driver uses incorrect APIs to unmap DMA memory which were
mapped using dma_map_single(). This patch fixes it to use
appropriate APIs for un-mapping DMA memory.

Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Loopback implementation should ignore the normal traffic

During the execution of loopback test, driver may receive the packets which
are not originated by this test, loopback implementation need to skip those
packets.

Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet/qlogic: use core min/max MTU checking

qede: min_mtu 46, max_mtu 9600
- Put define for max in qede.h

qlcnic: min_mtu 68, max_mtu 9600

CC: netdev@vger.kernel.org
CC Dept-GELinuxNICDev@qlogic.com
CC: Yuval Mintz <Yuval.Mintz@qlogic.com>
CC: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Allow unicast filtering

Apparently qede fails to set IFF_UNICAST_FLT, and as a result is not
actually performing unicast MAC filtering.
While we're at it - relax a hard-coded limitation that limits each
interface into using at most 15 unicast MAC addresses before turning
promiscuous. Instead utilize the HW resources to their limit.

Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Prevent GSO on long Geneve headers

Due to hardware limitation, when transmitting a geneve-encapsulated
packet with more than 32 bytes worth of geneve options the hardware
would not be able to crack the packet and consider it a regular UDP
packet.

This implements the ndo_features_check() in qede in order to prevent
GSO on said transmitted packets.

Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: GSO support for tunnels with outer csum

This patch adds GSO support for GRE and UDP tunnels
where outer checksums are enabled.

Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Pass MAC hints to VFs

Some hypervisors can support MAC hints to their VFs.
Even though we don't have such a hypervisor API in linux, we add
sufficient logic for the VF to be able to receive such hints and
set the mac accordingly - as long as the VF has not been set with
a MAC already.

Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add qedr framework

Adds a skeletal implementation of the qede RoCE driver -
The qedr has some dependencies of the state of the underlying base
interface. This adds some logic required with mutual registrations
and the ability to pass updates on 'intresting' events.

Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Update API for VF vlan protocol 802.1ad support

Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.

For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.

Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100

Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: mark qede_set_features() static

We get 1 warning when building kernel with W=1:
drivers/net/ethernet/qlogic/qede/qede_main.c:2113:5: warning: no previous prototype for 'qede_set_features' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.

Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Disallow dcbx configuration for VF interfaces.

Dcbx configuration is not supported for VF interfaces. Hence don't populate
the callbacks for VFs and also fail the dcbx-query for VFs.

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add support for Tx/Rx-only queues.

Add provision for configuring the fastpath queues with Tx (or Rx) only
functionality.

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Add support for VFs over legacy PFs

Modern VFs can't run on old non-compatible as the fastpath HSI is
slightly changed - but as the HSI is actually very close [basically,
a single bit whose meaning flipped] this can be supported with small
modifications.

The major differences would be in:
- Recognizing that VF is running on top of a legacy PF.
- Returning some slowpath configurations that are no longer needed
on top of modern PFs, but would be required when working over
the legacy ones.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix Tx timeout due to xmit_more

Driver uses netif_tx_queue_stopped() to make sure the xmit_more
indication will be honored, but that only checks for DRV_XOFF.

At the same time, it's possible that during transmission the DQL will
close the transmission queue with STACK_XOFF indication.
In re-configuration flows, when the threshold is relatively low, it's
possible that the device has no pending tranmissions, and during
tranmission the driver would miss doorbelling the HW.
Since there are no pending transmission, there will never be a Tx
completion [and thus the DQL would not remove the STACK_XOFF indication],
eventually causing the Tx queue to timeout.

While we're at it - also doorbell in case driver has to close the
transmission queue on its own [although this one is less important -
if the ring is full, we're bound to receive completion eventually,
which means the doorbell would only be postponed and not indefinetly
blocked].

Fixes: 312e06761c99 ("qede: Utilize xmit_more")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add support for per-queue stats.

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add support for capturing additional stats in ethtool-stats display.

The patch adds driver support for capturing stats ttl0_discard and
packet_too_big_discard in "ethtool -S" display.

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Add and modify some prints

This patch touches various prints in the driver - it reduces the
verbosity of some prints [which were previously logged by default]
while adding several new debug prints and modifying others.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Trivial modifications

Change qed* code in trivial manner; This isn't necessarily
semantic-only, but the end result is the same, i.e., no change
should occur from user perspective. Changes include:
- Using temporary variables to better fit 80-character restrictions.
- Removal of unused variables & code with no effect.
[plus some additional minor modifications].

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Semantic changes

Make semantic-only adjustments to qed* drivers, such as:
- Changes in code indentation.
- Usage of BIT() macro.
- re-naming of variables.
- Re-ordering of variable declerations.
- Removal of (== 0) and (!= 0) in conditions.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Reset statistics on explicit down

Adding the necessary logic to prevet statistics reset
on inner-reload introduced a bug, and now statistics
are reset only when re-probing the driver.

Fixes: a0d26d5a4fc8e ("qed*: Don't reset statistics on inner reload")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Don't try removing unconfigured vlans

As part of ndo_vlan_rx_kill_vid() implementation,
qede is requesting firmware to remove the vlan filter.
This currently happens even if the vlan wasn't previously
added [In case device ran out of vlan credits].

For PFs this doesn't cause any issues as the firmware
would simply ignore the removal request. But for VFs their
parent PF is holding an accounting of the configured vlans,
and such a request would cause the PF to fail the VF's
removal request.

Simply fix this for both PFs & VFs and don't remove filters
that were not previously added.

Fixes: 7c1bfcad9f3c8 ("qede: Add vlan filtering offload support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add get/set rx copy break tunable support

Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Utilize xmit_more

This patch uses xmit_more optimization to reduce
number of TX doorbells write per packet.

Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: qede_poll refactoring

This patch cleanups qede_poll() routine a bit
and allows qede_poll() to do single iteration to handle
TX completion [As under heavy TX load qede_poll() might
run for indefinite time in the while(1) loop for TX
completion processing and cause CPU stuck].

Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add support for handling IP fragmented packets.

When handling IP fragmented packets with csum in their
transport header, the csum isn't changed as part of the
fragmentation. As a result, the packet containing the
transport headers would have the correct csum of the original
packet, but one that mismatches the actual packet that
passes on the wire. As a result, on receive path HW would
give an indication that the packet has incorrect csum,
which would cause qede to discard the incoming packet.

Since HW also delivers a notification of IP fragments,
change driver behavior to pass such incoming packets
to stack and let it make the decision whether it needs
to be dropped.

Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Don't reset statistics on inner reload

Several user APIs can cause driver to perform an inner-reload.
Currently, doing this would cause the HW/FW statistics of the
adapter to reset, which isn't the expected behavior [statistics
should only reset on explicit unloads].

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Move all UDP port notifiers to single function

This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.

Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add dcbnl support.

This patch adds the interfaces for ieee/cee dcbnl callbacks and registers
them with the kernel.

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Revisit chain implementation

RoCE driver is going to need a 32-bit chain [current chain implementation
for qed* currently supports only 16-bit producer/consumer chains].

This patch adds said support, as well as doing other slight tweaks and
modifications to qed's chain API.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Utilize FW 8.10.3.0

The New QED firmware contains several fixes, including:
- Wrong classification of packets in 4-port devices.
- Anti-spoof interoperability with encapsulated packets.
- Tx-switching of encapsulated packets.
It also slightly improves Tx performance of the device.

In addition, this firmware contains the necessary logic for
supporting iscsi & rdma, for which we plan on pushing protocol
drivers in the imminent future.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: fix qed_fill_link() error handling

gcc warns about qed_fill_link possibly accessing uninitialized data:

drivers/net/ethernet/qlogic/qed/qed_main.c: In function 'qed_fill_link':
drivers/net/ethernet/qlogic/qed/qed_main.c:1170:35: error: 'link_caps' may be used uninitialized in this function [-Werror=maybe-uninitialized]

While this warning is only about the specific case of CONFIG_QED_SRIOV
being disabled but the function getting called for a VF (which should
never happen), another possibility is that qed_mcp_get_*() fails without
returning data.

This rearranges the code so we bail out in either of the two cases
and print a warning instead of accessing the uninitialized data.

The qed_link_output structure remains untouched in this case, but
all callers first call memset() on it, so at least we are not leaking
stack data then.

As discussed, we also use a compile-time check to ensure we never
use any of the VF code if CONFIG_QED_SRIOV is disabled, and the
PCI device table is updated to no longer bind to virtual functions
in that configuration.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Reload on GRO changes

Since driver is using a FW-based GRO implementation, this has some
effects on its ability to cope with GRO enablement/disablement.
As a result, driver must perform an inner-reload as a result of a state
change in the offload configuration of said feature.

[Failure to do so means network stack would continue to receive
aggregated packets even though user requested the feature to be disabled].

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix VF minimum BW setting

VF is currently ignoring the minimum provided by the API,
mistakenly using the maximum for minimum as well.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix DMA address APIs usage

Driver incorrectly uses dma_unmap_addr_set() to set
a variable which is in truth a dma_addr_t
[i.e not defined using DEFINE_DMA_UNMAP_ADDR()] and is
being used by the driver flows other than unmapping
physical addresses. This patch fixes driver fastpath
where CONFIG_NEED_DMA_MAP_STATE is not set.

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mm: rename _count, field of the struct page, to _refcount

Many developers already know that field for reference count of the
struct page is _count and atomic type. They would try to handle it
directly and this could break the purpose of page reference count
tracepoint. To prevent direct _count modification, this patch rename it
to _refcount and add warning message on the code. After that, developer
who need to handle reference count will find that field should not be
accessed directly.

[akpm@linux-foundation.org: fix comments, per Vlastimil]
[akpm@linux-foundation.org: Documentation/vm/transhuge.txt too]
[sfr@canb.auug.org.au: sync ethernet driver changes]
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Yuval Mintz <yuval.mintz@qlogic.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/page_ref: use page_ref helper instead of direct modification of _count

page_reference manipulation functions are introduced to track down
reference count change of the page. Use it instead of direct
modification of _count.

Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

qed*: Tx-switching configuration

Device should be configured by default to VEB once VFs are active.
This changes the configuration of both PFs' and VFs' vports into enabling
tx-switching once sriov is enabled.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: support ndo_get_vf_config

Allows the user to view the VF configuration by observing the PF's
device.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: IOV support spoof-checking

Add support in `ndo_set_vf_spoofchk' for allowing PF control over
its VF spoof-checking configuration.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: IOV link control

This adds support in 2 ndo that allow PF to tweak the VF's view of the
link - `ndo_set_vf_link_state' to allow it a view independent of the PF's,
and `ndo_set_vf_rate' which would allow the PF to limit the VF speed.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Support forced MAC

Allows the PF to enforce the VF's mac.
i.e., by using `ip link ... vf <x> mac <value>'.

While a MAC is forced, PF would prevent the VF from configuring any other
MAC.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Support PVID configuration

This adds support for PF control over the VF vlan configuration.
I.e., `ip link ... vf <x> vlan <vid>' should now be supported.

1. <vid> != 0 => VF receives [unknowingly] only traffic tagged by
<vid> and tags all outgoing traffic sent by VF with <vid>.
2. <vid> == 0 ==> Remove the pvid configuration, reverting to previous.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add VF support

Adding a PCI callback for `sriov_configure' and a new PCI device id for
the VF [+ Some minor changes to accomodate differences between PF and VF
at the qede].
Following this, VF creation should be possible and the entire subset of
existing PF functionality that's allow to VFs should be supported.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Introduce VFs

This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.

This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: uninitialized variable in qede_start_xmit()

"data_split" was never set to false. It's just uninitialized.

Fixes: 2950219d87b0 ('qede: Add basic network device support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: prevent chip hang when increasing channels

qede requires qed to provide enough resources to accommodate 16 combined
channels, but that upper-bound isn't actually being enforced by it.
Instead, qed inform back to qede how many channels can be opened based on
available resources - but that calculation doesn't really take into account
the resources requested by qede; Instead it considers other FW/HW available
resources.

As a result, if a user would increase the number of channels to more than
16 [e.g., using ethtool] the chip would hang.

This change increments the resources requested by qede to 64 combined
channels instead of 16; This value is an upper bound on the possible
available channels [due to other FW/HW resources].

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: add implementation for internal loopback test.

This patch adds the qede implementation for internal loopback test.

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: Align statistics names

There's a difference in statsitics' names starting at qed and
propagating to qede, where egress counters indicate ranges while ingress
counters indiciate high-end.
Align all statistcs to follow the same conventions - name indicates range.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix single MTU sized packet from firmware GRO flow

In firmware assisted GRO flow there could be a single MTU sized
segment arriving due to firmware aggregation timeout/last segment
in an aggregation flow, which is not expected to be an actual gro
packet. So If a skb has zero frags from the GRO flow then simply
push it in the stack as non gso skb.

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix setting Skb network header

Skb's network header needs to be set before extracting IPv4/IPv6
headers from it.

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix various memory allocation error flows for fastpath

This patch handles memory allocation failures for fastpath
gracefully in the driver.

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add fastpath support for tunneling

This patch enables netdev tunneling features and adds
TX/RX fastpath support for tunneling in driver.

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed/qede: Add GENEVE tunnel slowpath configuration support

This patch enables GENEVE tunnel on the adapter and
add support for driver hooks to configure UDP ports
for GENEVE tunnel offload to be performed by the adapter.

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed/qede: Add VXLAN tunnel slowpath configuration support

This patch enables VXLAN tunnel on the adapter and
add support for driver hooks to configure UDP ports
for VXLAN tunnel offload to be performed by the adapter.

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: add Rx flow hash/indirection support.

Adds support for the following via ethtool:
- UDP configuration of RSS based on 2-tuple/4-tuple.
- RSS hash key.
- RSS indirection table.

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: remove version dependency

Inbox drivers don't need versioning scheme in order to guarantee
compatibility, as both qed and qede are compiled from same codebase.

Signed-off-by: Rahul Verma <rahul.verma@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix net-next "make ARCH=x86_64"

'commit 55482edc25f0606851de42e73618f813f310d009
("qede: Add slowpath/fastpath support and enable hardware GRO")'
introduces below error when compiling net-next with "make ARCH=x86_64"

drivers/built-in.o: In function `qede_rx_int':
qede_main.c:(.text+0x6101a0): undefined reference to `tcp_gro_complete'

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add slowpath/fastpath support and enable hardware GRO

This patch configures hardware to use GRO and adds support
for fastpath APIs to handle HW aggregated packets.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed/qede: Add infrastructure support for hardware GRO

This patch adds mainly structures and APIs prototype changes
in order to give support for qede slowpath/fastpath support
for the same.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed, qede: rebrand module description

Drop the `QL4xxx 40G/100G' and use `FastLinQ 4xxxx' instead.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Don't report link change needlessly

There are several corner cases where driver might get a 2nd notification
about the same link change. Don't log any additional changes if the
physical carrier is already reported as it should.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Linearize SKBs when needed

There's a corner-case in HW where an SKB queued for transmission that
contains too many frags will cause FW to assert.
This patch solves this by linearizing the SKB if necessary.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Change pci DID for 10g device

The device ID for the 10g module has changed. Populate the pci_ids table
accordingly.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add vlan filtering offload support

Device would start receiving only vlan-tagged traffic with tags matching
that of one of the configured vlan IDs, unless:
- Device is expliicly placed in PROMISC mode.
- Device exhausts its vlan filter credits.

Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed/qede: use 8.7.3.0 FW.

This patch moves the qed* driver into utilizing the 8.7.3.0 FW.
This new FW is required for a lot of new SW features, including:
- Vlan filtering offload
- Encapsulation offload support
- HW ingress aggregations
As well as paving the way for the possibility of adding storage protocols
in the future.

V2:
- Fix kbuild test robot error/warnings.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add support for {get, set}_channels

Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add basic ethtool support

This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]

In addition it adds the ability to change the MTU.

Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add support for link

This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.

This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.

Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: classification configuration

Add the ability to configure basic classification in driver by
implementing ndo_set_mac_address() and ndo_set_rx_mode().

Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add basic network device support

This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.

Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Add basic Network driver

The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.

This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>