nfp: support TX VLAN ctag insert in NFDK

Add support for TX VLAN ctag insert
which may be configured via ethtool.
e.g.
# ethtool -K $DEV tx-vlan-offload on

The NIC supplies VLAN insert information as packet metadata.
The fields of this VLAN metadata including vlan_proto and vlan tag.

Configuration control bit NFP_NET_CFG_CTRL_TXVLAN_V2 is to
signal availability of ctag-insert features of the firmware.

NFDK is used to communicate via PCIE to NFP-3800 based NICs
while NFD3 is used for other NICs supported by the NFP driver.
This features is currently implemented only for NFD3 and
this patch adds support for it with NFDK.

Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220711093048.1911698-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

nfp: support RX VLAN ctag/stag strip

Add support for RX VLAN ctag/stag strip
which may be configured via ethtool.

e.g.
# ethtool -K $DEV rx-vlan-offload on
# ethtool -K $DEV rx-vlan-stag-hw-parse on

Ctag-stripped and stag-stripped cannot be enabled at the same time
because currently the kernel supports only one layer of VLAN stripping.

The NIC supplies VLAN strip information as packet metadata.
The fields of this VLAN metadata are:

* strip flag: 1 for stripped; 0 for unstripped
* tci: VLAN TCI ID
* tpid: 1 for ETH_P_8021AD; 0 for ETH_P_8021Q

Configuration control bits NFP_NET_CFG_CTRL_RXVLAN_V2 and
NFP_NET_CFG_CTRL_RXQINQ are to signal availability of
ctag-strip and stag-strip features of the firmware.

Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: support vepa mode in HW bridge

Add support for VEPA mode of HW bridge.
The default remains VEB mode.
The mode may be configured using ndo_bridge_setlink,
and inspected using ndo_bridge_getlink.

Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

nfp: support 48-bit DMA addressing for NFP3800

48-bit DMA addressing is supported in NFP3800 HW and implemented
in NFDK firmware, so enable this feature in driver now. Note that
with this change, NFD3 firmware, which doesn't implement 48-bit
DMA, cannot be used for NFP3800 any more.

RX free list descriptor, used by both NFD3 and NFDK, is also modified
to support 48-bit DMA. That's OK because the top bits is always get
set to 0 when assigned with 40-bit address.

Based on initial work of Jakub Kicinski <jakub.kicinski@netronome.com>.

Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: add support for NFDK data path

Add new data path. The TX is completely different, each packet
has multiple descriptor entries (between 2 and 32). TX ring is
divided into blocks 32 descriptor, and descritors of one packet
can't cross block bounds. The RX side is the same for now.

ABI version 5 or later is required. There is no support for
VLAN insertion on TX. XDP_TX action and AF_XDP zero-copy is not
implemented in NFDK path.

Changes to Jakub's work:
* Move statistics of hw_csum_tx after jumbo packet's segmentation.
* Set L3_CSUM flag to enable recaculating of L3 header checksum
in ipv4 case.
* Mark the case of TSO a packet with metadata prepended as
unsupported.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Xingfeng Hu <xingfeng.hu@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Dianchao Wang <dianchao.wang@corigine.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>