net: lan743x: Add set RFE read fifo threshold for PCI1x1x chips

PCI11x1x Rev B0 devices might drop packets when receiving back to back frames
at 2.5G link speed. Change the B0 Rev device's Receive filtering Engine FIFO
threshold parameter from its hardware default of 4 to 3 dwords to prevent the
problem. Rev C0 and later hardware already defaults to 3 dwords.

Fixes: bb4f6bffe33c ("net: lan743x: Add PCI11010 / PCI11414 device IDs")
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326065805.686128-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: microchip: lan743x : bidirectional throughput improvement

The LAN743x/PCI11xxx DMA descriptors are always 4 dwords long, but the
device supports placing the descriptors in memory back to back or
reserving space in between them using its DMA_DESCRIPTOR_SPACE (DSPACE)
configurable hardware setting. Currently DSPACE is unnecessarily set to
match the host's L1 cache line size, resulting in space reserved in
between descriptors in most platforms and causing a suboptimal behavior
(single PCIe Mem transaction per descriptor). By changing the setting
to DSPACE=16 many descriptors can be packed in a single PCIe Mem
transaction resulting in a massive performance improvement in
bidirectional tests without any negative effects.
Tested and verified improvements on x64 PC and several ARM platforms
(typical data below)

Test setup 1: x64 PC with LAN7430 ---> x64 PC

iperf3 UDP bidirectional with DSPACE set to L1 CACHE Size:
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID][Role] Interval Transfer Bitrate
[ 5][TX-C] 0.00-10.00 sec 170 MBytes 143 Mbits/sec sender
[ 5][TX-C] 0.00-10.04 sec 169 MBytes 141 Mbits/sec receiver
[ 7][RX-C] 0.00-10.00 sec 1.02 GBytes 876 Mbits/sec sender
[ 7][RX-C] 0.00-10.04 sec 1.02 GBytes 870 Mbits/sec receiver

iperf3 UDP bidirectional with DSPACE set to 16 Bytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID][Role] Interval Transfer Bitrate
[ 5][TX-C] 0.00-10.00 sec 1.11 GBytes 956 Mbits/sec sender
[ 5][TX-C] 0.00-10.04 sec 1.11 GBytes 951 Mbits/sec receiver
[ 7][RX-C] 0.00-10.00 sec 1.10 GBytes 948 Mbits/sec sender
[ 7][RX-C] 0.00-10.04 sec 1.10 GBytes 942 Mbits/sec receiver

Test setup 2 : RK3399 with LAN7430 ---> x64 PC

RK3399 Spec:
The SOM-RK3399 is ARM module designed and developed by FriendlyElec.
Cores: 64-bit Dual Core Cortex-A72 + Quad Core Cortex-A53
Frequency: Cortex-A72(up to 2.0GHz), Cortex-A53(up to 1.5GHz)
PCIe: PCIe x4, compatible with PCIe 2.1, Dual operation mode

iperf3 UDP bidirectional with DSPACE set to L1 CACHE Size:
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID][Role] Interval Transfer Bitrate
[ 5][TX-C] 0.00-10.00 sec 534 MBytes 448 Mbits/sec sender
[ 5][TX-C] 0.00-10.05 sec 534 MBytes 446 Mbits/sec receiver
[ 7][RX-C] 0.00-10.00 sec 1.12 GBytes 961 Mbits/sec sender
[ 7][RX-C] 0.00-10.05 sec 1.11 GBytes 946 Mbits/sec receiver

iperf3 UDP bidirectional with DSPACE set to 16 Bytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID][Role] Interval Transfer Bitrate
[ 5][TX-C] 0.00-10.00 sec 966 MBytes 810 Mbits/sec sender
[ 5][TX-C] 0.00-10.04 sec 965 MBytes 806 Mbits/sec receiver
[ 7][RX-C] 0.00-10.00 sec 1.11 GBytes 956 Mbits/sec sender
[ 7][RX-C] 0.00-10.04 sec 1.07 GBytes 919 Mbits/sec receiver

Signed-off-by: Vishvambar Panth S <vishvambarpanth.s@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231116054350.620420-1-vishvambarpanth.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: microchip: lan743x: improve throughput with rx timestamp config

Currently all RX frames are timestamped which results in a performance
penalty when timestamping is not needed. The default is now being
changed to not timestamp any Rx frames (HWTSTAMP_FILTER_NONE), but
support has been added to allow changing the desired RX timestamping
mode (HWTSTAMP_FILTER_ALL - which was the previous setting and
HWTSTAMP_FILTER_PTP_V2_EVENT are now supported) using
SIOCSHWTSTAMP. All settings were tested using the hwstamp_ctl application.
It is also noted that ptp4l, when started, preconfigures the device to
timestamp using HWTSTAMP_FILTER_PTP_V2_EVENT, so this driver continues
to work properly "out of the box".

Test setup: x64 PC with LAN7430 ---> x64 PC as partner

iperf3 with - Timestamp all incoming packets:
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-5.05 sec 517 MBytes 859 Mbits/sec 0 sender
[ 5] 0.00-5.00 sec 515 MBytes 864 Mbits/sec receiver

iperf Done.

iperf3 with - Timestamp only PTP packets:
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-5.04 sec 563 MBytes 937 Mbits/sec 0 sender
[ 5] 0.00-5.00 sec 561 MBytes 941 Mbits/sec receiver

Signed-off-by: Vishvambar Panth S <vishvambarpanth.s@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231020185801.25649-1-vishvambarpanth.s@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: lan743x: add generic implementation for phy interface selection

Add logic to read the Phy interface from MAC_CR register for LAN743x
driver.

Checks for the LAN7430/31 or pci11x1x devices and the adapter
interface is updated accordingly. For LAN7431, adapter interface is set
based on Bit 19 of MAC_CR register as MII or RGMII which removes the
forced RGMII/GMII configurations in lan743x_phy_open().

Signed-off-by: Pavithra Sathyanarayanan <Pavithra.Sathyanarayanan@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: lan743x: Add support to SGMII register dump for PCI11010/PCI11414 chips

Add support to SGMII register dump

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: lan743x: Add support for get_pauseparam and set_pauseparam

Add pause get and set functions

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: lan743x: Add support for Rx IP & TCP checksum offload

Add Rx IP and TCP checksum offload

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan743x: Fix to use multiqueue start/stop APIs

- Fix to use multiqueue start/stop APIs
- Change to return NETDEV_TX_BUSY instead of holding the TX skb when busy
- Increase Tx ring size to 128 to address performance issues in some platforms
- Use NAPI_POLL_WEIGHT for Tx Napi handler instead of ring dependent value
- Use multiqueue to register 4 Rx channels

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan743x: Add support to SGMII 1G and 2.5G

Add SGMII access read and write functions
Add support to SGMII 1G and 2.5G for PCI11010/PCI11414 chips

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: lan743x: Add support to Secure-ON WOL

Add support to Magic Packet Detection with Secure-ON for PCI11010/PCI11414 chips

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: lan743x: Add support for PTP-IO Event Output (Periodic Output)

Add support for PTP-IO Event Output (Periodic Output - perout) for
PCI11010/PCI11414 chips

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan743x: Add support for PTP-IO Event Input External Timestamp (extts)

PTP-IOs block provides for time stamping PTP-IO input events.
PTP-IOs are numbered from 0 to 11.
When a PTP-IO is enabled by the corresponding bit in the PTP-IO
Capture Configuration Register, a rising or falling edge,
respectively, will capture the 1588 Local Time Counter

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan743x: Add support for OTP

Add new the OTP read and write access functions for PCI11010/PCI11414 chips
PCI11010/PCI11414 OTP module register offsets are different from
LAN743x OTP module

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan743x: Add support for EEPROM

Add new the EEPROM read and write access functions and system lock
protection to access by devices for PCI11010/PCI11414 chips

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan743x: Add support to display Tx Queue statistics

Tx 4 queue statistics display through ethtool application

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan743x: Add support for Clause-45 MDIO PHY management

Add support for Clause-45 MDIO PHY management

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan743x: Add support for SGMII interface

This change facilitates the selection between SGMII and (R)GIII
interfaces

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan743x: Increase MSI(x) vectors to 16 and Int de-assertion timers to 10

Increase MSI / MSI-X vectors supported from 8 to 16 and
Interrupt De-assertion timers from 8 to 10

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan743x: Add support for 4 Tx queues

Add support for 4 Tx queues

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: lan743x: Add PCI11010 / PCI11414 device IDs

PCI11010/PCI11414 devices are enhancement of Ethernet LAN743x chip family.

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: microchip: lan743x: Increase rx ring size to improve rx performance

Increase the rx ring size (LAN743X_RX_RING_SIZE) to improve rx performance on some platforms.
Tested on x86 PC with EVB-LAN7430.
The iperf3.7 TCPIP improved from 881 Mbps to 922 Mbps, and UDP improved from 817 Mbps to 936 Mbps.

Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: microchip: lan743x: add support for PTP pulse width (duty cycle)

If the PTP_PEROUT_DUTY_CYCLE flag is set, then check if the
request_on value in ptp_perout_request matches the pre-defined
values or a toggle option.
Return a failure if the value is not supported.

Preserve the old behaviors if the PTP_PEROUT_DUTY_CYCLE flag is not
set.

Tested with an oscilloscope on EVB-LAN7430:
e.g., to output PPS 1sec period 500mS on (high) to GPIO 2.
./testptp -L 2,2
./testptp -p 1000000000 -w 500000000

Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Link: https://lore.kernel.org/r/1634046593-64312-1-git-send-email-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

lan743x: boost performance on cpu archs w/o dma cache snooping

The buffers in the lan743x driver's receive ring are always 9K,
even when the largest packet that can be received (the mtu) is
much smaller. This performs particularly badly on cpu archs
without dma cache snooping (such as ARM): each received packet
results in a 9K dma_{map|unmap} operation, which is very expensive
because cpu caches need to be invalidated.

Careful measurement of the driver rx path on armv7 reveals that
the cpu spends the majority of its time waiting for cache
invalidation.

Optimize by keeping the rx ring buffer size as close as possible
to the mtu. This limits the amount of cache that requires
invalidation.

This optimization would normally force us to re-allocate all
ring buffers when the mtu is changed - a disruptive event,
because it can only happen when the network interface is down.

Remove the need to re-allocate all ring buffers by adding support
for multi-buffer frames. Now any combination of mtu and ring
buffer size will work. When the mtu changes from mtu1 to mtu2,
consumed buffers of size mtu1 are lazily replaced by newly
allocated buffers of size mtu2.

These optimizations double the rx performance on armv7.
Third parties report 3x rx speedup on armv8.

Tested with iperf3 on a freescale imx6qp + lan7430, both sides
set to mtu 1500 bytes, measure rx performance:

Before:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-20.00 sec 550 MBytes 231 Mbits/sec 0
After:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-20.00 sec 1.33 GBytes 570 Mbits/sec 0

Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan743x: fix endianness when accessing descriptors

TX/RX descriptor ring fields are always little-endian, but conversion
wasn't performed for big-endian CPUs, so the driver failed to work.

This patch makes the driver work on big-endian CPUs. It was tested and
confirmed to work on NXP P1010 processor (PowerPC).

Signed-off-by: Alexey Denisov <rtgbnm@gmail.com>
Link: https://lore.kernel.org/r/20210128044859.280219-1-rtgbnm@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

lan743x: replace polling loop by wait_event_timeout()

The driver's ISR sends a 'software interrupt' event to the probe()
thread using the following method:
- probe(): write 0 to flag, enable s/w interrupt
- probe(): poll on flag, relax using usleep_range()
- ISR : write 1 to flag

Replace with wake_up() / wait_event_timeout(). Besides being easier
to get right, this abstraction has better timing and memory
consistency properties.

Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # lan7430
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201123191529.14908-2-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

lan743x: replace devicetree phy parse code with library function

The code in this driver which parses the devicetree to determine
the phy/fixed link setup, can be replaced by a single library
function: of_phy_get_and_connect().

Behaviour is identical, except that the library function will
complain when 'phy-connection-type' is omitted, instead of
blindly using PHY_INTERFACE_MODE_NA, which would result in an
invalid phy configuration.

The library function no longer brings out the exact phy_mode,
but the driver doesn't need this, because phy_interface_is_rgmii()
queries the phydev directly. Remove 'phy_mode' from the private
adapter struct.

While we're here, log info about the attached phy on connect,
this is useful because the phy type and connection method is now
fully configurable via the devicetree.

Tested on a lan7430 chip with built-in phy. Verified that adding
fixed-link/phy-connection-type in the devicetree results in a
fixed-link setup. Used ethtool to verify that the devicetree
settings are used.

Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # lan7430
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201116170155.26967-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

lan743x: fix "BUG: invalid wait context" when setting rx mode

In the net core, the struct net_device_ops -> ndo_set_rx_mode()
callback is called with the dev->addr_list_lock spinlock held.

However, this driver's ndo_set_rx_mode callback eventually calls
lan743x_dp_write(), which acquires a mutex. Mutex acquisition
may sleep, and this is not allowed when holding a spinlock.

Fix by removing the dp_lock mutex entirely. Its purpose is to
prevent concurrent accesses to the data port. No concurrent
accesses are possible, because the dev->addr_list_lock
spinlock in the core only lets through one thread at a time.

Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201109203828.5115-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

lan743x: Added fixed link and RGMII support

Microchip lan7431 is frequently connected to a phy. However, it
can also be directly connected to a MII remote peer without
any phy in between. For supporting such a phyless hardware setup
in Linux we utilized phylib, which supports a fixed-link
configuration via the device tree. And we added support for
defining the connection type R/GMII in the device tree.

New behavior:
-------------
. The automatic speed and duplex detection of the lan743x silicon
between mac and phy is disabled. Instead phylib is used like in
other typical Linux drivers. The usage of phylib allows to
specify fixed-link parameters in the device tree.

. The device tree entry phy-connection-type is supported now with
the modes RGMII or (G)MII (default).

Development state:
------------------
. Tested with fixed-phy configurations. Not yet tested in normal
configurations with phy. Microchip kindly offered testing
as soon as the Corona measures allow this.

. All review findings of Andrew Lunn are included

Example:
--------
&pcie {
status = "okay";

host@0 {
reg = <0 0 0 0 0>;

#address-cells = <3>;
#size-cells = <2>;

ethernet@0 {
compatible = "weyland-yutani,noscom1", "microchip,lan743x";
status = "okay";
reg = <0 0 0 0 0>;
phy-connection-type = "rgmii";

fixed-link {
speed = <100>;
full-duplex;
};
};
};
};

Signed-off-by: Roelof Berg <rberg@berg-solutions.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan743x: Provide Read/Write Access to on chip OTP

The LAN743x includes on chip One-Time-Programmable (OTP) memory.

This patch extends the ethtool EEPROM read/write interface to
access OTP memory space.

The currently existing interface is limited, as it does not
allow OTP read, and OTP writes are restricted to
offset==0, length==512, and data[0]==0xF3.

This patch removes these restrictions and adds a private flag
called OTP_ACCESS, which is used to switch between EEPROM, and
OTP modes.

The private flag OTP_ACCESS is configurable through the
ethtool --set-priv-flags command.
And visible through the
ethtool --show-priv-flags command.

By default OTP_ACCESS is false, and there for previously existing
EEPROM commands will work exactly the same. However now access to
OTP requires one extra step of setting OTP_ACCESS to true. This
flag controls the read, write, and length reporting, functions
of ethtool.

EEPROM presence is not checked when setting or clearing this flag.
If the EEPROM is not present, the user, as before, will need to
diagnose that using existing read and write function of ethtool,
while OTP_ACCESS is false.

Updates for V2:
Added comments as to why this patch is needed.
Added comments explaining that EEPROM presence is not check
when setting or clearing the OTP_ACCESS flag.
Added length checking to all otp/eeprom read/write functions.

Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan743x: Enable driver to work with LAN7431

This driver was designed to work with both LAN7430 and LAN7431.
The only difference between the two is the LAN7431 has support
for external phy.

This change adds LAN7431 to the list of recognized devices
supported by this driver.

Updates for v2:
changed 'fixes' tag to match defined format

fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan743x: lan743x: Add PTP support

PTP support includes:
Ingress, and egress timestamping.
One step timestamping available.
PTP clock support.
Periodic output support.

Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan743x: Add RSS support

Implement RSS support

Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan743x: Add EEE support

Implement EEE support

Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan743x: Add power management support

Implement power management
Supports suspend, resume, and Wake on LAN

Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan743x: Add support for ethtool eeprom access

Implement ethtool eeprom access
Also provides access to OTP (One Time Programming)

Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan743x: Add support for ethtool statistics

Implement ethtool statistics

Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan743x: Add main source files for new lan743x driver

Add main source files for new lan743x driver

Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>