net/mlx5e: E-Switch, Add a check that log_max_l2_table is valid

If log_max_l2_table is 0 there is no really room for one L2 address.
and should be treated as not supported.
Do the check in MPFS init and for vport context events which
both used to update L2 address.

Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5: Fix crash during sync firmware reset

When setting Bluefield to DPU NIC mode using mlxconfig tool + sync
firmware reset flow, we run into scenario where the host was not
eswitch manager at the time of mlx5 driver load but becomes eswitch manager
after the sync firmware reset flow. This results in null pointer
access of mpfs structure during mac filter add. This change prevents null
pointer access but mpfs table entries will not be added.

Fixes: 5ec697446f46 ("net/mlx5: Add support for devlink reload action fw activate")
Signed-off-by: Suresh Devarakonda <ramad@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-12-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

{net,vdpa}/mlx5: Configure interface MAC into mpfs L2 table

net/mlx5: Expose MPFS configuration API

MPFS is the multi physical function switch that bridges traffic between
the physical port and any physical functions associated with it. The
driver is required to add or remove MAC entries to properly forward
incoming traffic to the correct physical function.

We export the API to control MPFS so that other drivers, such as
mlx5_vdpa are able to add MAC addresses of their network interfaces.

The MAC address of the vdpa interface must be configured into the MPFS L2
address. Failing to do so could cause, in some NIC configurations, failure
to forward packets to the vdpa network device instance.

Fix this by adding calls to update the MPFS table.

CC: <mst@redhat.com>
CC: <jasowang@redhat.com>
CC: <virtualization@lists.linux-foundation.org>
Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5: Update mpfs.c new cmd interface

Do mass update of mpfs.c to reuse newly introduced
mlx5_cmd_exec_in*() interfaces.

Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>

net/mlx5: MPFS, Allow adding the same MAC more than once

Remove the limitation preventing adding a vport's MAC address to the
Multi-Physical Function Switch (MPFS) more than once per E-switch, as
there is no difference in the MPFS if an address is being used by an
E-switch more than once.

This allows the E-switch to have multiple vports with the same MAC
address, allowing vports to be classified by VLAN id instead of by MAC
if desired.

Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: MPFS, Cleanup add MAC flow

Unify and isolate the error handling flow in mlx5_mpfs_add_mac(),
removing code duplication.

Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

mellanox: Switch to bitmap_zalloc()

Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5: Fix required capability for manipulating MPFS

Manipulating of the MPFS requires eswitch manager capabilities.

Fixes: eeb66cdb6826 ('net/mlx5: Separate between E-Switch and MPFS')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: Separate between E-Switch and MPFS

Multi-Physical Function Switch (MPFs) is required for when multi-PF
configuration is enabled to allow passing user configured unicast MAC
addresses to the requesting PF.

Before this patch eswitch.c used to manage the HW MPFS l2 table,
E-Switch always (regardless of sriov) enabled vport(0) (NIC PF) vport's
contexts update on unicast mac address list changes, to populate the PF's
MPFS L2 table accordingly.

In downstream patch we would like to allow compiling the driver without
E-Switch functionalities, for that we move MPFS l2 table logic out
of eswitch.c into its own file, and provide Kconfig flag (MLX5_MPFS) to
allow compiling out MPFS for those who don't want Multi-PF support.

NIC PF netdevice will now directly update MPFS l2 table via the new MPFS
API. VF netdevice has no access to MPFS L2 table, so E-Switch will remain
responsible of updating its MPFS l2 table on behalf of its VFs.

Due to this change we also don't require enabling vport(0) (PF vport)
unicast mac changes events anymore, for when SRIOV is not enabled.
Which means E-Switch is now activated only on SRIOV activation, and not
required otherwise.

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jes Sorensen <jsorensen@fb.com>
Cc: kernel-team@fb.com