net/mlx5: Refactor mlx5_flow_destination->rep pointer to vport num

Currently the destination rep pointer is only used for comparisons or to
obtain vport number from it. Since it is used both during flow creation and
deletion it may point to representor of another eswitch instance which can
be deallocated during driver unload even when there are rules pointing to
it[0]. Refactor the code to store vport number and 'valid' flag instead of
the representor pointer.

[0]:
[176805.886303] ==================================================================
[176805.889433] BUG: KASAN: slab-use-after-free in esw_cleanup_dests+0x390/0x440 [mlx5_core]
[176805.892981] Read of size 2 at addr ffff888155090aa0 by task modprobe/27280

[176805.895462] CPU: 3 PID: 27280 Comm: modprobe Tainted: G B 6.6.0-rc3+ #1
[176805.896771] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[176805.898514] Call Trace:
[176805.899026] <TASK>
[176805.899519] dump_stack_lvl+0x33/0x50
[176805.900221] print_report+0xc2/0x610
[176805.900893] ? mlx5_chains_put_table+0x33d/0x8d0 [mlx5_core]
[176805.901897] ? esw_cleanup_dests+0x390/0x440 [mlx5_core]
[176805.902852] kasan_report+0xac/0xe0
[176805.903509] ? esw_cleanup_dests+0x390/0x440 [mlx5_core]
[176805.904461] esw_cleanup_dests+0x390/0x440 [mlx5_core]
[176805.905223] __mlx5_eswitch_del_rule+0x1ae/0x460 [mlx5_core]
[176805.906044] ? esw_cleanup_dests+0x440/0x440 [mlx5_core]
[176805.906822] ? xas_find_conflict+0x420/0x420
[176805.907496] ? down_read+0x11e/0x200
[176805.908046] mlx5e_tc_rule_unoffload+0xc4/0x2a0 [mlx5_core]
[176805.908844] mlx5e_tc_del_fdb_flow+0x7da/0xb10 [mlx5_core]
[176805.909597] mlx5e_flow_put+0x4b/0x80 [mlx5_core]
[176805.910275] mlx5e_delete_flower+0x5b4/0xb70 [mlx5_core]
[176805.911010] tc_setup_cb_reoffload+0x27/0xb0
[176805.911648] fl_reoffload+0x62d/0x900 [cls_flower]
[176805.912313] ? mlx5e_rep_indr_block_unbind+0xd0/0xd0 [mlx5_core]
[176805.913151] ? __fl_put+0x230/0x230 [cls_flower]
[176805.913768] ? filter_irq_stacks+0x90/0x90
[176805.914335] ? kasan_save_stack+0x1e/0x40
[176805.914893] ? kasan_set_track+0x21/0x30
[176805.915484] ? kasan_save_free_info+0x27/0x40
[176805.916105] tcf_block_playback_offloads+0x79/0x1f0
[176805.916773] ? mlx5e_rep_indr_block_unbind+0xd0/0xd0 [mlx5_core]
[176805.917647] tcf_block_unbind+0x12d/0x330
[176805.918239] tcf_block_offload_cmd.isra.0+0x24e/0x320
[176805.918953] ? tcf_block_bind+0x770/0x770
[176805.919551] ? _raw_read_unlock_irqrestore+0x30/0x30
[176805.920236] ? mutex_lock+0x7d/0xd0
[176805.920735] ? mutex_unlock+0x80/0xd0
[176805.921255] tcf_block_offload_unbind+0xa5/0x120
[176805.921909] __tcf_block_put+0xc2/0x2d0
[176805.922467] ingress_destroy+0xf4/0x3d0 [sch_ingress]
[176805.923178] __qdisc_destroy+0x9d/0x280
[176805.923741] dev_shutdown+0x1c6/0x330
[176805.924295] unregister_netdevice_many_notify+0x6ef/0x1500
[176805.925034] ? netdev_freemem+0x50/0x50
[176805.925610] ? _raw_spin_lock_irq+0x7b/0xd0
[176805.926235] ? _raw_spin_lock_bh+0xe0/0xe0
[176805.926849] unregister_netdevice_queue+0x1e0/0x280
[176805.927592] ? unregister_netdevice_many+0x10/0x10
[176805.928275] unregister_netdev+0x18/0x20
[176805.928835] mlx5e_vport_rep_unload+0xc0/0x200 [mlx5_core]
[176805.929608] mlx5_esw_offloads_unload_rep+0x9d/0xc0 [mlx5_core]
[176805.930492] mlx5_eswitch_unload_vf_vports+0x108/0x1a0 [mlx5_core]
[176805.931422] ? mlx5_eswitch_unload_sf_vport+0x50/0x50 [mlx5_core]
[176805.932304] ? rwsem_down_write_slowpath+0x11f0/0x11f0
[176805.932987] mlx5_eswitch_disable_sriov+0x6f9/0xa60 [mlx5_core]
[176805.933807] ? mlx5_core_disable_hca+0xe1/0x130 [mlx5_core]
[176805.934576] ? mlx5_eswitch_disable_locked+0x580/0x580 [mlx5_core]
[176805.935463] mlx5_device_disable_sriov+0x138/0x490 [mlx5_core]
[176805.936308] mlx5_sriov_disable+0x8c/0xb0 [mlx5_core]
[176805.937063] remove_one+0x7f/0x210 [mlx5_core]
[176805.937711] pci_device_remove+0x96/0x1c0
[176805.938289] device_release_driver_internal+0x361/0x520
[176805.938981] ? kobject_put+0x5c/0x330
[176805.939553] driver_detach+0xd7/0x1d0
[176805.940101] bus_remove_driver+0x11f/0x290
[176805.943847] pci_unregister_driver+0x23/0x1f0
[176805.944505] mlx5_cleanup+0xc/0x20 [mlx5_core]
[176805.945189] __x64_sys_delete_module+0x2b3/0x450
[176805.945837] ? module_flags+0x300/0x300
[176805.946377] ? dput+0xc2/0x830
[176805.946848] ? __kasan_record_aux_stack+0x9c/0xb0
[176805.947555] ? __call_rcu_common.constprop.0+0x46c/0xb50
[176805.948338] ? fpregs_assert_state_consistent+0x1d/0xa0
[176805.949055] ? exit_to_user_mode_prepare+0x30/0x120
[176805.949713] do_syscall_64+0x3d/0x90
[176805.950226] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[176805.950904] RIP: 0033:0x7f7f42c3f5ab
[176805.951462] Code: 73 01 c3 48 8b 0d 75 a8 1b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 45 a8 1b 00 f7 d8 64 89 01 48
[176805.953710] RSP: 002b:00007fff07dc9d08 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[176805.954691] RAX: ffffffffffffffda RBX: 000055b6e91c01e0 RCX: 00007f7f42c3f5ab
[176805.955691] RDX: 0000000000000000 RSI: 0000000000000800 RDI: 000055b6e91c0248
[176805.956662] RBP: 000055b6e91c01e0 R08: 0000000000000000 R09: 0000000000000000
[176805.957601] R10: 00007f7f42d9eac0 R11: 0000000000000206 R12: 000055b6e91c0248
[176805.958593] R13: 0000000000000000 R14: 000055b6e91bfb38 R15: 0000000000000000
[176805.959599] </TASK>

[176805.960324] Allocated by task 20490:
[176805.960893] kasan_save_stack+0x1e/0x40
[176805.961463] kasan_set_track+0x21/0x30
[176805.962019] __kasan_kmalloc+0x77/0x90
[176805.962554] esw_offloads_init+0x1bb/0x480 [mlx5_core]
[176805.963318] mlx5_eswitch_init+0xc70/0x15c0 [mlx5_core]
[176805.964092] mlx5_init_one_devl_locked+0x366/0x1230 [mlx5_core]
[176805.964902] probe_one+0x6f7/0xc90 [mlx5_core]
[176805.965541] local_pci_probe+0xd7/0x180
[176805.966075] pci_device_probe+0x231/0x6f0
[176805.966631] really_probe+0x1d4/0xb50
[176805.967179] __driver_probe_device+0x18d/0x450
[176805.967810] driver_probe_device+0x49/0x120
[176805.968431] __driver_attach+0x1fb/0x490
[176805.968976] bus_for_each_dev+0xed/0x170
[176805.969560] bus_add_driver+0x21a/0x570
[176805.970124] driver_register+0x133/0x460
[176805.970684] 0xffffffffa0678065
[176805.971180] do_one_initcall+0x92/0x2b0
[176805.971744] do_init_module+0x22d/0x720
[176805.972318] load_module+0x58c3/0x63b0
[176805.972847] init_module_from_file+0xd2/0x130
[176805.973441] __x64_sys_finit_module+0x389/0x7c0
[176805.974045] do_syscall_64+0x3d/0x90
[176805.974556] entry_SYSCALL_64_after_hwframe+0x46/0xb0

[176805.975566] Freed by task 27280:
[176805.976077] kasan_save_stack+0x1e/0x40
[176805.976655] kasan_set_track+0x21/0x30
[176805.977221] kasan_save_free_info+0x27/0x40
[176805.977834] ____kasan_slab_free+0x11a/0x1b0
[176805.978505] __kmem_cache_free+0x163/0x2d0
[176805.979113] esw_offloads_cleanup_reps+0xb8/0x120 [mlx5_core]
[176805.979963] mlx5_eswitch_cleanup+0x182/0x270 [mlx5_core]
[176805.980763] mlx5_cleanup_once+0x9a/0x1e0 [mlx5_core]
[176805.981477] mlx5_uninit_one+0xa9/0x180 [mlx5_core]
[176805.982196] remove_one+0x8f/0x210 [mlx5_core]
[176805.982868] pci_device_remove+0x96/0x1c0
[176805.983461] device_release_driver_internal+0x361/0x520
[176805.984169] driver_detach+0xd7/0x1d0
[176805.984702] bus_remove_driver+0x11f/0x290
[176805.985261] pci_unregister_driver+0x23/0x1f0
[176805.985847] mlx5_cleanup+0xc/0x20 [mlx5_core]
[176805.986483] __x64_sys_delete_module+0x2b3/0x450
[176805.987126] do_syscall_64+0x3d/0x90
[176805.987665] entry_SYSCALL_64_after_hwframe+0x46/0xb0

[176805.988667] Last potentially related work creation:
[176805.989305] kasan_save_stack+0x1e/0x40
[176805.989839] __kasan_record_aux_stack+0x9c/0xb0
[176805.990443] kvfree_call_rcu+0x84/0xa30
[176805.990973] clean_xps_maps+0x265/0x6e0
[176805.991547] netif_reset_xps_queues.part.0+0x3f/0x80
[176805.992226] unregister_netdevice_many_notify+0xfcf/0x1500
[176805.992966] unregister_netdevice_queue+0x1e0/0x280
[176805.993638] unregister_netdev+0x18/0x20
[176805.994205] mlx5e_remove+0xba/0x1e0 [mlx5_core]
[176805.994872] auxiliary_bus_remove+0x52/0x70
[176805.995490] device_release_driver_internal+0x361/0x520
[176805.996196] bus_remove_device+0x1e1/0x3d0
[176805.996767] device_del+0x390/0x980
[176805.997270] mlx5_rescan_drivers_locked.part.0+0x130/0x540 [mlx5_core]
[176805.998195] mlx5_unregister_device+0x77/0xc0 [mlx5_core]
[176805.998989] mlx5_uninit_one+0x41/0x180 [mlx5_core]
[176805.999719] remove_one+0x8f/0x210 [mlx5_core]
[176806.000387] pci_device_remove+0x96/0x1c0
[176806.000938] device_release_driver_internal+0x361/0x520
[176806.001612] unbind_store+0xd8/0xf0
[176806.002108] kernfs_fop_write_iter+0x2c0/0x440
[176806.002748] vfs_write+0x725/0xba0
[176806.003294] ksys_write+0xed/0x1c0
[176806.003823] do_syscall_64+0x3d/0x90
[176806.004357] entry_SYSCALL_64_after_hwframe+0x46/0xb0

[176806.005317] The buggy address belongs to the object at ffff888155090a80
which belongs to the cache kmalloc-64 of size 64
[176806.006774] The buggy address is located 32 bytes inside of
freed 64-byte region [ffff888155090a80, ffff888155090ac0)

[176806.008773] The buggy address belongs to the physical page:
[176806.009480] page:00000000a407e0e6 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x155090
[176806.010633] flags: 0x200000000000800(slab|node=0|zone=2)
[176806.011352] page_type: 0xffffffff()
[176806.011905] raw: 0200000000000800 ffff888100042640 ffffea000422b1c0 dead000000000004
[176806.012949] raw: 0000000000000000 0000000000200020 00000001ffffffff 0000000000000000
[176806.013933] page dumped because: kasan: bad access detected

[176806.014935] Memory state around the buggy address:
[176806.015601] ffff888155090980: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[176806.016568] ffff888155090a00: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[176806.017497] >ffff888155090a80: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[176806.018438] ^
[176806.019007] ffff888155090b00: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[176806.020001] ffff888155090b80: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[176806.020996] ==================================================================

Fixes: a508728a4c8b ("net/mlx5e: VF tunnel RX traffic offloading")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Revert "net/mlx5e: Don't use termination table when redundant"

This reverts commit 14624d7247fcd0f3114a6f5f17b3c8d1020fbbb7.

The termination table usage is requires for DMFS steering mode as firmware
doesn't support mixed table destinations list which causes following
syndrome with hairpin rules:

[81922.283225] mlx5_core 0000:08:00.0: mlx5_cmd_out_err:803:(pid 25977): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xaca205), err(-22)

Fixes: 14624d7247fc ("net/mlx5e: Don't use termination table when redundant")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Don't use termination table when redundant

Current code used termination table for each vport destination
while it's only required for hairpin, i.e. uplink to uplink, or
when vlan push on rx action being used.
Fix to skip using termination table for vport destinations that
do not require it.

Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Fix use-after-free when reverting termination table

When having multiple dests with termination tables and second one
or afterwards fails the driver reverts usage of term tables but
doesn't reset the assignment in attr->dests[num_vport_dests].termtbl
which case a use-after-free when releasing the rule.
Fix by resetting the assignment of termtbl to null.

Fixes: 10caabdaad5a ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: E-Switch, Fix comparing termination table instance

The pkt_reformat pointer being saved under flow_act and not
dest attribute in the termination table instance.
Fix the comparison pointers.

Also fix returning success if one pkt_reformat pointer is null
and the other is not.

Fixes: 249ccc3c95bd ("net/mlx5e: Add support for offloading traffic from uplink to uplink")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5: VLAN push on RX, pop on TX

Some older NIC hardware isn't capable of doing VLAN push on RX and pop
on TX.

A workaround has been added in software to support it, but it has a
performance penalty since it requires a hairpin + loopback.

There's no such limitation with the newer NICs, so no need to pay the
price of the w/a. With this change the software w/a is disabled for
certain HW versions and steering modes that support it.

Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Refactor eswitch attr flags to just attr flags

The flags are flow attrs and not esw specific attr flags.
Refactor to remove the esw prefix and move from eswitch.h
to en_tc.h where struct mlx5_flow_attr exists.

Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Term table handling of internal port rules

Adjust termination table logic to handle rules which
involve internal port as filter or forwarding device.

For cases where the rule forwards from internal port
to uplink, always choose to go via termination table.
This is because it is not known from where the packet
originally arrived to the internal port and it is possible
that it came from the uplink itself, in which case
a term table is required to perform hairpin.
If the packet arrived from a vport, going via term
table has no effect.

For cases where the rule forwards to an internal port
from uplink the rep pointer will point to the uplink rep,
avoid going via termination table as it is not required.

Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Offload tc rules that redirect to ovs internal port

Allow offloading rules that redirect to ovs internal port
ingress and egress.

To support redirect to ingress device, offloading of REDIRECT_INGRESS
action is added.

When a tc rule redirects to ovs internal port, the hw rule will
overwrite the input vport value in reg_c0 with a new vport metadata
value that is mapped for this internal port using the internal
port mapping api that is introduce in previous patches.
After that the hw rule will redirect the packet to the root table
to continue processing with the new vport metadata value.

The new vport metadata value indicates that this packet is now
arriving through an internal port and therefore should be processed
using rules that apply on the same internal port as the filter device.
Therefore, following rules that apply on this internal port will have
to match on the same vport metadata value as part of their matching
keys to make sure the packet belongs to the internal port.

Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Support accept action

Support TC generic 'accept' action in mlx5 by introducing
MLX5_ESW_ATTR_FLAG_ACCEPT attribute flag. Flag has similar semantics to
existing MLX5_ESW_ATTR_FLAG_SLOW_PATH flag, however, dedicated flag is
required because existing 'slow path' flag can be flipped by tunneling
subsystem when neighbor changes state.

Introduce new helper function mlx5_esw_attr_flags_skip() to check whether
attribute flags for 'slow path' or 'accept' action are set and use it in
eswitch code instead of direct bit manipulation.

Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5: Set term table as an unmanaged flow table

Termination tables are restricted to have the default miss action and
cannot be set to forward to another table in case of a miss.
If the fs prio of the termination table is not the last one in the
list, fs_core will attempt to attach it to another table.

Set the unmanaged ft flag when creating the termination table ft
and select the tc offload prio for it to prevent fs_core from selecting
the forwarding to next ft miss action and use the default one.

In addition, set the flow that forwards to the termination table to
ignore ft level restrictions since the ft level is not set by fs_core
for unamanged fts.

Fixes: 249ccc3c95bd ("net/mlx5e: Add support for offloading traffic from uplink to uplink")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>

net/mlx5: Fix err prints and return when creating termination table

Fix print to print correct error code and not using IS_ERR() which
will just result in always printing 1.
Also return real err instead of always -EOPNOTSUPP.

Fixes: 10caabdaad5a ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5: Set reformat action when needed for termination rules

For remote mirroring, after the tunnel packets are received, they are
decapsulated and sent to representor, then re-encapsulated and sent
out over another tunnel. So reformat action is set only when the
destination is required to do encapsulation.

Fixes: 249ccc3c95bd ("net/mlx5e: Add support for offloading traffic from uplink to uplink")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5: E-Switch, Improve error messages in term table creation

Add error code to the error messages and removed duplicated message:
if termination table creation failed, we already get an error message
in mlx5_eswitch_termtbl_create, so no need for the additional error print
in the calling function.

Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5: Refactor tc flow attributes structure

In order to support chains and connection tracking offload for
nic flows, there's a need to introduce a common flow attributes
struct so that these features can be agnostic and have access to
a single attributes struct, regardless of the flow type.

Therefore, a new tc flow attributes format is introduced to allow
access to attributes that are common to eswitch and nic flows.

The common attributes will always get allocated for the new flows,
regardless of their type, while the type specific attributes are
separated into different structs and will be allocated based on the
flow type to avoid memory waste.

When allocating the flow attributes the caller provides the flow
steering namespace and according the namespace type the additional
space for the extra, type specific, attributes is determined and
added to the total attribute allocation size.

In addition, the attributes that are going to be common to both
flow types are moved to the common attributes struct.

Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Add support for offloading traffic from uplink to uplink

Termination tables change the direction of a packet in hw from RX to SX
pipeline. Use that to offload hairpin flows received from uplink and
sent back to uplink.

Currently termination tables are used for pushing VLAN to packets
received from uplink and targeting a VF. Extend the implementation to
allow forwarding packets to uplink. These packets can either be
encapsulated or not.

In case encapsulation is needed before forwarding, move the reformat
object to the termination table as required.

Extend the hash table key to include tunnel information for the sake of
reusing reformat objects.

Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: Don't use termination tables in slow path

Don't use termination tables for packets that are steered to the slow path,
as a pre-step for supporting packet encap (packet reformat) action on
termination tables. Packet encap (reformat action) actions steer the packet
to the slow path until outer arp entries are resolved.

Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: Accept flow rules without match

Allow passing NULL spec when creating a flow rule. Such rules will act
as "catch all" flow rules.

Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: Eswitch, avoid redundant mask

misc_params.source_port is a 16 bit field already so no need for
redundant masking against 0xffff. Also change local variables type to
u16.

Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: Refactor mlx5_create_auto_grouped_flow_table

Refactor mlx5_create_auto_grouped_flow_table() to use ft_attr param
which already carries the max_fte, prio and flags memebers, and is
used the same in similar mlx5_create_flow_table() function.

Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Use correct enum to determine uplink port

For vlan push action, if eswitch flow source capability is enabled, flow
source value compared with MLX5_VPORT_UPLINK enum, to determine uplink
port. This lead to syndrome in dmesg if try to add vlan push action.
For example:
$ tc filter add dev vxlan0 ingress protocol ip prio 1 flower \
enc_dst_port 4789 \
action tunnel_key unset pipe \
action vlan push id 20 pipe \
action mirred egress redirect dev ens1f0_0
$ dmesg
...
[ 2456.883693] mlx5_core 0000:82:00.0: mlx5_cmd_check:756:(pid 5273): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xa9c090)
Use the correct enum value MLX5_FLOW_CONTEXT_FLOW_SOURCE_UPLINK.

Fixes: bb204dcf39fe ("net/mlx5e: Determine source port properly for vlan push action")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Determine source port properly for vlan push action

Termination tables are used for vlan push actions on uplink ports.
To support RoCE dual port the source port value was placed in a register.
Fix the code to use an API method returning the source port according to
the FW capabilities.

Fixes: 10caabdaad5a ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: reduce stack usage in mlx5_eswitch_termtbl_create

Putting an empty 'mlx5_flow_spec' structure on the stack is a bit
wasteful and causes a warning on 32-bit architectures when building
with clang -fsanitize-coverage:

drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_termtbl.c: In function 'mlx5_eswitch_termtbl_create':
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_termtbl.c:90:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]

Since the structure is never written to, we can statically allocate
it to avoid the stack usage. To be on the safe side, mark all
subsequent function arguments that we pass it into as 'const'
as well.

Fixes: 10caabdaad5a ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Use termination table for VLAN push actions

HW does not support push VLAN action in the RX direction (packets
arriving from the wire). The FW works around this limitation by haripining
the packet. The hairpin workaround applies only when the push VLAN action
is specified in a termination table, assuring that there are no actions
following the haripin.

Instantiate termination table for push VLAN actions. Re-use identical
terminating tables for increased HW cache efficiency.

Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>