net/mlx5e: Remove mlx5e_dbg() and msglvl support

The msglvl support was implemented using the mlx5e_dbg() macro which is
rarely used in the driver, and is not very useful when you can just use
dynamic debug instead.
Remove mlx5e_dbg() and convert its usages to netdev_dbg().

Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Consider internal buffers size in port buffer calculations

Currently, when a user triggers a change in port buffer headroom
(buffers 0-7), the driver checks that the requested headroom does
not exceed the total port buffer size. However, this check does not
take into account the internal buffers (buffers 8-9), which are also
part of the total port buffer. This can result in treating invalid port
buffer change requests as valid, causing unintended changes to the shared
buffer.

To address this, include the internal buffers size in the calculation of
available port buffer space which ensures that port buffer requests do not
exceed the correct limit.

Furthermore, remove internal buffers (8-9) size from the total_size
calculation as these buffers are reserved for internal use and are not
exposed to the user.

While at it, add verbosity to the debug prints in
mlx5e_port_query_buffer() function to ease future debugging.

Fixes: ecdf2dadee8e ("net/mlx5e: Receive buffer support for DCBX")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5: Read the TC mapping of all priorities on ETS query

When ETS configurations are queried by the user to get the mapping
assignment between packet priority and traffic class, only priorities up
to maximum TCs are queried from QTCT register in FW to retrieve their
assigned TC, leaving the rest of the priorities mapped to the default
TC #0 which might be misleading.

Fix by querying the TC mapping of all priorities on each ETS query,
regardless of the maximum number of TCs configured in FW.

Fixes: 820c2c5e773d ("net/mlx5e: Read ETS settings directly from firmware")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Remove unused mlx5e_dcbnl_build_rep_netdev function

Commit
7a9fb35e8c3a ("net/mlx5e: Do not reload ethernet ports when changing eswitch mode")
removed the usage of mlx5e_dcbnl_build_rep_netdev() from the driver,
delete the function.

Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Fix trust state reset in reload

Setting dscp2prio during the driver reload can cause dcb ieee app list to
be not empty after the reload finish and as a result to a conflict between
the priority trust state reported by the app and the state in the device
register.

Reset the dcb ieee app list on initialization in case this is
conflicting with the register status.

Fixes: 2a5e7a1344f4 ("net/mlx5e: Add dcbnl dscp to priority support")
Signed-off-by: Moshe Tal <moshet@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Use READ_ONCE/WRITE_ONCE for DCBX trust state

trust_state can be written while mlx5e_select_queue() is reading it. To
avoid inconsistencies, use READ_ONCE and WRITE_ONCE for access and
updates, and touch the variable only once per operation.

Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Cleanup safe switch channels API by passing params

mlx5e_safe_switch_channels accepts new_chs as a parameter and opens new
channels in place, then copying them to priv->channels. It requires all
the callers to allocate space for this temporary storage of the new
channels.

This commit cleans up the API by replacing new_chs with new_params, a
meaningful subset of new_chs to be filled by the caller. The temporary
space for the new channels is allocated inside mlx5e_safe_switch_params
(a new name for mlx5e_safe_switch_channels). An extra copy of params is
made, but since it's control flow, it's not critical.

Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Refactor on-the-fly configuration changes

This commit extends mlx5e_safe_switch_channels() to support on-the-fly
configuration changes, when the channels are open, but don't need to be
recreated. Such flows exist when a parameter being changed doesn't
affect how the queues are created, or when the queues can be modified
while remaining active.

Before this commit, such flows were handled as special cases on the
caller site. This commit adds this functionality to
mlx5e_safe_switch_channels(), allowing the caller to pass a boolean
indicating whether it's required to recreate the channels or it's
allowed to skip it. The logic of switching channel parameters is now
completely encapsulated into mlx5e_safe_switch_channels().

Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Use mlx5e_safe_switch_channels when channels are closed

This commit uses new functionality of mlx5e_safe_switch_channels
introduced by the previous commit to reduce the amount of repeating
similar code all over the driver.

It's very common in mlx5e to call mlx5e_safe_switch_channels when the
channels are open, but assign parameters and run hardware commands
manually when the channels are closed.

After the previous commit it's no longer needed to do such manual things
every time, so this commit removes unneeded code and relies on the new
functionality of mlx5e_safe_switch_channels. Some of the places are
refactored and simplified, where more complex flows are used to change
configuration on the fly, without recreating the channels (the logic is
rewritten in a more robust way, with a reset required by default and a
list of exceptions).

Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Revert parameters on errors when changing trust state without reset

Trust state may be changed without recreating the channels. It happens
when the channels are closed, and when channel parameters (min inline
mode) stay the same after changing the trust state. Changing the trust
state is a hardware command that may fail. The current code didn't
restore the channel parameters to their old values if an error happened
and the channels were closed. This commit adds handling for this case.

Fixes: 6e0504c69811 ("net/mlx5e: Change inline mode correctly when changing trust state")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Fix port buffers cell size value

Device unit for port buffers size, xoff_threshold and xon_threshold is
cells. Fix a bug in driver where cell unit size was hard-coded to
128 bytes. This hard-coded value is buggy, as it is wrong for some hardware
versions.

Driver to read cell size from SBCAM register and translate bytes to cell
units accordingly.

In order to fix the bug, this patch exposes SBCAM (Shared buffer
capabilities mask) layout and defines.

If SBCAM.cap_cell_size is valid, use it for all bytes to cells
calculations. If not valid, fallback to 128.

Cell size do not change on the fly per device. Instead of issuing SBCAM
access reg command every time such translation is needed, cache it in
mlx5e_dcbx as part of mlx5e_dcbnl_initialize(). Pass dcbx.port_buff_cell_sz
as a param to every function that needs bytes to cells translation.

While fixing the bug, move MLX5E_BUFFER_CELL_SHIFT macro to
en_dcbnl.c, as it is only used by that file.

Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Make mlx5e_dcbnl_ops static

Fix sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/en_dcbnl.c:988:29:
error: symbol 'mlx5e_dcbnl_ops' was not declared. Should it be static?

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Take DCBNL-related definitions into dedicated files

Take DCBNL-related definitions out of the common en.h header,
Use a dedicated header file for exposing them.
Some need not to be exposed, use them locally in the .c file.
Use stubs to eliminate use of CONFIG_MLX5_CORE_EN_DCB in the
generic control flows.

Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Change inline mode correctly when changing trust state

The current steps that are performed when the trust state changes, if
the channels are active:

1. The trust state is changed in hardware.

2. The new inline mode is calculated.

3. If the new inline mode is different, the channels are recreated using
the new inline mode.

This approach has some issues:

1. There is a time gap between changing trust state in hardware and
starting sending enough inline headers (the latter happens after
recreation of channels). It leads to failed transmissions and error
CQEs.

2. If the new channels fail to open, we'll be left with the old ones,
but the hardware will be configured for the new trust state, so the
interval when we can see TX errors never ends.

This patch fixes the issues above by moving the trust state change into
the preactivate hook that runs during the recreation of the channels
when no channels are active, so it eliminates the gap of partially
applied configuration. If the inline mode doesn't change with the change
of the trust state, the channels won't be recreated, just like before
this patch.

Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Add context to the preactivate hook

Sometimes the preactivate hook of mlx5e_safe_switch_channels needs more
parameters than just struct mlx5e_priv *. For such cases, a new
parameter (void *context) is added to preactivate hooks.

Some of the existing normal functions are currently used as preactivate
callbacks. To avoid adding an extra unused parameter, they are wrapped
in an automatic way using the MLX5E_DEFINE_PREACTIVATE_WRAPPER_CTX
macro.

Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Tx, Soften inline mode VLAN dependencies

If capable, use zero inline mode in TX WQE for non-VLAN packets.
For VLAN ones, keep the enforcement of at least L2 inline mode,
unless the WQE VLAN insertion offload cap is on.

Performance:
Tested single core packet rate of 64Bytes.

NIC: ConnectX-5
CPU: Intel(R) Xeon(R) Gold 6154 CPU @ 3.00GHz

pktgen:
Before: 12.46 Mpps
After: 14.65 Mpps (+17.5%)

XDP_TX:
The MPWQE flow is not affected, as it already has this optimization.
So we test with priv-flag xdp_tx_mpwqe: off.

Before: 9.90 Mpps
After: 10.20 Mpps (+3%)

Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Tested-by: Noam Stolero <noams@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: Handle host PF vport mac/guid for ECPF

When ECPF is eswitch manager, it has the privilege to query and
configure the mac and node guid of host PF.

While vport number of host PF is 0, the vport command should be
issued with other_vport set in this case as the cmd is issued by
ECPF vport(0xfffe).

Add a specific function to query own vport mac. Low level functions
are used by vport manager to query/modify any vport mac and node guid.

Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Wrap the open and apply of channels in one fail-safe function

Take into a function the common code structure of opening
a side set of channels followed by a call to apply them.

Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Cleanup of dcbnl related fields

Remove unused netdev_registered_init/remove in en.h
Return ENOSUPPORT if the check MLX5_DSCP_SUPPORTED fails.
Remove extra white space

Fixes: 2a5e7a1344f4 ("net/mlx5e: Add dcbnl dscp to priority support")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Cc: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Set port trust mode to PCP as default

The hairpin offload code has dependency on the trust mode being PCP.

Hence we should set PCP as the default for handling cases where we are
disallowed to read the trust mode from the FW, or failed to initialize it.

Fixes: 106be53b6b0a ('net/mlx5e: Set per priority hairpin pairs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Refine ets validation function

Removed an error message received when configuring ETS total
bandwidth to be zero.
Our hardware doesn't support such configuration, so we shall
reject it in the driver. Nevertheless, we removed the error message
in order to eliminate error messages caused by old userspace tools
who try to pass such configuration.

Fixes: ff0891915cd7 ("net/mlx5e: Fix ETS BW check")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Receive buffer support for DCBX

Add dcbnl's set/get buffer configuration callback that allows user to
set/get buffer size configuration and priority to buffer mapping.

By default, firmware controls receive buffer configuration and priority
of buffer mapping based on the changes in pfc settings. When set buffer
call back is triggered, the buffer configuration changes to manual mode.

The manual mode means mlx5 driver will adjust the buffer configuration
accordingly based on the changes in pfc settings.

ConnectX buffer stride is 128 Bytes. If the buffer size is not multiple
of 128, the buffer size will be rounded down to the nearest multiple of
128.

Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: DCBNL fix min inline header size for dscp

When the trust state is set to dscp and the netdev is down, the inline
header size is not updated. When netdev is up, the inline header size
stays at L2 instead of IP.

Fix this issue by updating the private parameter when the netdev is in
down so that when netdev is up, it picks up the right header size.

Fixes: fbcb127e89ba ("net/mlx5e: Support DSCP trust state ...")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Check support before TC swap in ETS init

Should not do the following swap between TCs 0 and 1
when max num of TCs is 1:
tclass[prio=0]=1, tclass[prio=1]=0, tclass[prio=i]=i (for i>1)

Fixes: 08fb1dacdd76 ("net/mlx5e: Support DCBNL IEEE ETS")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Add error print in ETS init

ETS initialization might fail, add a print to indicate
such failures.

Fixes: 08fb1dacdd76 ("net/mlx5e: Support DCBNL IEEE ETS")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Fix ETS BW check

Fix bug that allows ets bw sum to be 0% when ets tc type exists.

Fixes: 08fb1dacdd76 ('net/mlx5e: Support DCBNL IEEE ETS')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: DCBNL, Add debug messages log

Add debug print when changing the configuration of QoS through dcbnl.
Use ethtool -s <devname> msglvl hw on/off to toggle debug messages.

Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Support DSCP trust state to Ethernet's IP packet on SQ

If the port is in DSCP trust state, packets are placed in the right
priority queue based on the dscp value. This is done by selecting
the transmit queue based on the dscp of the skb.

Until now select_queue honors priority only from the vlan header.
However that is not sufficient in cases where port trust state is DSCP
mode as packet might not even contain vlan header. Therefore if the port
is in dscp trust state and vport's min inline mode is not NONE,
copy the IP header to the eseg's inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features such
as xdpsq, icosq are not modified.

Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Add dcbnl dscp to priority support

This patch implements dcbnl hooks to set and delete DSCP to priority map
as defined by the DCB subsystem. Device maintains internal trust state
which needs to be set to DSCP state for performing DSCP to priority mapping.

When the first dscp to priority APP entry is added by the user, the
trust state is changed to dscp.

When the last dscp to priority APP entry is deleted by the user, the
trust state is changed to pcp.

If user sends multiple dscp to priority APP entries on the same dscp,
the last sent one will take effect. All the previous sent will be
deleted.

The dscp to priority APP entries are added and deleted in the net/dcb
APP database using dcb_ieee_setapp/getapp.

Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: DCBNL, Implement tc with ets type and zero bandwidth

Previously, tc with ets type and zero bandwidth is not accepted
by driver. This behavior does not follow the IEEE802.1qaz spec.

If there are tcs with ets type and zero bandwidth, these tcs are
assigned to the lowest priority tc_group #0. We equally distribute
100% bw of the tc_group #0 to these zero bandwidth ets tcs.
Also, the non zero bandwidth ets tcs are assigned to tc_group #1.

If there is no zero bandwidth ets tc, the non zero bandwidth ets tcs
are assigned to tc_group #0.

Fixes: cdcf11212b22 ("net/mlx5e: Validate BW weight values of ETS")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Fix DCB_CAP_ATTR_DCBX capability for DCBNL getcap.

Current code doesn't report DCB_CAP_DCBX_HOST capability when query
through getcap. User space lldptool expects capability to have HOST mode
set when it wants to configure DCBX CEE mode. In absence of HOST mode
capability, lldptool fails to switch to CEE mode.

This fix returns DCB_CAP_DCBX_HOST capability when port's DCBX
controlled mode is under software control.

Fixes: 3a6a931dfb8e ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Check for qos capability in dcbnl_initialize

qos capability is the master capability bit that determines
if the DCBX is supported for the PCI function. If this bit is off,
driver cannot run any dcbx code.

Fixes: e207b7e99176 ("net/mlx5e: ConnectX-4 firmware support for DCBX")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Initialize CEE's getpermhwaddr address buffer to 0xff

Latest change in open-lldp code uses bytes 6-11 of perm_addr buffer
as the Ethernet source address for the host TLV packet.
Since our driver does not fill these bytes, they stay at zero and
the open-lldp code ends up sending the TLV packet with zero source
address and the switch drops this packet.

The fix is to initialize these bytes to 0xff. The open-lldp code
considers 0xff:ff:ff:ff:ff:ff as the invalid address and falls back to
use the host's mac address as the Ethernet source address.

Fixes: 3a6a931dfb8e ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: remove IEEE/CEE mode check when setting DCBX mode

Currently, the function setdcbx fails if the request dcbx mode
is either IEEE or CEE. We remove the IEEE/CEE mode check because
we support both IEEE and CEE interfaces.

Fixes: 3a6a931dfb8e ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Check ets capability before ets query FW command

On dcbnl callback getpgtccfgtx, the driver should check the ets
capability before ets query command is sent to firmware.
It is valid to return from this void function without changing in/out
parameters, as these parameters are initialized to
DCB_ATTR_VALUE_UNDEFINED.

Fixes: 3a6a931dfb8e ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5: Change ENOTSUPP to EOPNOTSUPP

As ENOTSUPP is specific to NFS, change the return error value to
EOPNOTSUPP in various places in the mlx5 driver.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Suggested-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

net/mlx5e: Check ets capability before initializing ets settings

During the initial setup, the ets command is sent to firmware
without checking if the HCA supports ets. This causes the invalid
command error. Add the ets capiblity check before sending firmware
command to initialize ets settings.

Fixes: e207b7e99176 ("net/mlx5e: ConnectX-4 firmware support for DCBX")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Add DCBX control interface

Use setdcbx interface to set the DCBX mode to firmware or os.
If setdcbx is called with mode value of zero, the DCBX mode
is set to firmware.

Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: ConnectX-4 firmware support for DCBX

DBCX by default is controlled by firmware where dcbx capability bit
is set. In this mode, firmware is responsible for reading/sending the
TLV packets from/to the remote partner.

This patch sets up the infrastructure to move between HOST/FW DCBX
control mode.

Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Read ETS settings directly from firmware

Issue description:
Current implementation saves the ETS settings from user in
a temporal soft copy and returns this settings when user
queries the ETS settings.

With the new DCBX firmware, the ETS settings can be changed
by firmware when the DCBX is in firmware controlled mode. Therefore,
user will obtain wrong values from the temporal soft copy.

Solution:
1. Read the ETS settings directly from firmware.
2. For tc_tsa:
a. Initialize tc_tsa to vendor IEEE_8021QAZ_TSA_VENDOR at netdev
creation.
b. When reading ETS setting from FW, if the traffic class bandwidth
is less than 100, set tc_tsa to IEEE_8021QAZ_TSA_ETS. This
implementation solves the scenarios when the DCBX is in FW control
and willing bit is on which means the ETS setting is dictated
by remote switch.

Also check ETS capability where needed.

Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Support DCBX CEE API

Add DCBX CEE API interface for ConnectX-4. Configurations are stored in
a temporary structure and are applied to the card's firmware when
the CEE's setall callback function is called.

Note:
priority group in CEE is equivalent to traffic class in ConnectX-4
hardware spec.

bw allocation per priority in CEE is not supported because ConnectX-4
only supports bw allocation per traffic class.

user priority in CEE does not have an equivalent term in ConnectX-4.
Therefore, user priority to priority mapping in CEE is not supported.

Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5: Add error prints when validate ETS failed

Upon set ETS failure due to user invalid input, add error prints to
specify the exact error to the user.

Fixes: cdcf11212b22 ('net/mlx5e: Validate BW weight values of ETS')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Validate BW weight values of ETS

Valid weight assigned to ETS TClass values are 1-100

Fixes: 08fb1dacdd76 ('net/mlx5e: Support DCBNL IEEE ETS')
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Toggle link only after modifying port parameters

Add a dedicated function to toggle port link. It should be called only
after setting a port register.
Toggle will set port link to down and bring it back up in case that it's
admin status was up.

Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Add per priority group to PPort counters

Expose counters providing information for each priority level (PCP) through
ethtool -S option and DCBNL.
This includes rx/tx bytes, frames, and pause counters.

Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Implement DCBNL IEEE max rate

Add support for DCBNL IEEE get/set max rate.

Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Support DCBNL IEEE PFC

Implement the set/get DCBNL IEEE PFC callbacks.

Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Support DCBNL IEEE ETS

Support the ndo_setup_tc callback and the needed methods
for multi TC/UP support, and removed the default_vlan_prio
from mlx5e_priv which is always 0, it was replaced with
hardcoded "0" in the new select queue method.

For that we now create MAX_NUM_TC num of TISs (one per prio)
on netdevice creation instead of priv->params.num_tc which
was always 1.

So far each channel had a single TXQ, Now each channel has a
TXQ per TC (Traffic Class).

Added en_dcbnl.c which implements the set/get DCBNL IEEE ETS,
set/get dcbx and registers the mlx5e dcbnl ops.

We still use the kernel's default TXQ selection method to select the
channel to transmit through but now we use our own method to select
the TXQ inside the channel based on VLAN priority.

In mlx5, as opposed to mlx4, tc group N gets lower priority than
tc group N+1.

CC: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>