octeontx2-pf: Add TC flower offload support for TCP flags

This patch adds TC offload support for matching TCP flags
from TCP header.

Example usage:
tc qdisc add dev eth0 ingress

TC rule to drop the TCP SYN packets:
tc filter add dev eth0 ingress protocol ip flower ip_proto tcp tcp_flags
0x02/0x3f skip_sw action drop

Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Add filter profiles in hardware to extract packet headers

This patch adds hardware profile supports for extracting packet headers.
It makes sure that hardware is capabale of extracting ICMP, CPT, ERSPAN
headers.

Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-pf: TC flower offload support for ICMP type and code

Adds tc offload support for matching on ICMP type and code.

Example usage:
To enable adding tc ingress rules
tc qdisc add dev eth0 ingress

TC rule drop the ICMP echo reply:
tc filter add dev eth0 protocol ip parent ffff: \
flower ip_proto icmp type 8 code 0 skip_sw action drop

TC rule to drop ICMPv6 echo reply:
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 ip_proto icmpv6 type 128 code 0 action drop

Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Fix marking couple of structure as __packed

Couple of structures was not marked as __packed. This patch
fixes the same and mark them as __packed.

Fixes: 42006910b5ea ("octeontx2-af: cleanup KPU config data")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-pf: Tc flower offload support for MPLS

This patch extends flower offload support for MPLS protocol.
Due to hardware limitation, currently driver supports lse
depth up to 4.

Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: TC flower offload support for inner VLAN

Extend the current TC flower offload support to enable filters matching
inner VLAN, and support offload of those filters to hardware.

Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230804045935.3010554-3-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-pf: TC flower offload support for SPI field

Driver support to offload TC flower rules which matches
against SPI field of IPSEC packets (AH/ESP).

Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-pf: Add support to filter packet based on IP fragment

1. Added support to filter packets based on IP fragment.
For IPv4 packets check for ip_flag == 0x20 (more fragment bit set).
For IPv6 packets check for next_header == 0x2c (next_header set to
'fragment header for IPv6')
2. Added configuration support from both "ethtool ntuple" and "tc flower".

Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Allow mkex profile without DMAC and add L2M/L2B header extraction support

1. It is possible to have custom mkex profiles which do not extract
DMAC at all into the key. Hence allow mkex profiles which do not
have DMAC to be loaded into MCAM hardware. This patch also adds
debugging prints needed to identify profiles with wrong
configuration.

2. If a mkex profile set "l2l3mb" field for Rx interface,
then Rx multicast and broadcast entry should be configured.

Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20221031090856.1404303-1-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: Exact match scan from kex profile

CN10KB silicon supports exact match table. Scanning KEX
profile should check for exact match feature is enabled
and then set profile masks properly.

These kex profile masks are required to configure NPC
MCAM drop rules. If there is a miss in exact match table,
these drop rules will drop those packets.

Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: Exact match support

CN10KB silicon has support for exact match table. This table
can be used to match maimum 64 bit value of KPU parsed output.
Hit/non hit in exact match table can be used as a KEX key to
NPC mcam.

This patch makes use of Exact match table to increase number of
DMAC filters supported. NPC mcam is no more need for each of these
DMAC entries as will be populated in Exact match table.

This patch implements following

1. Initialization of exact match table only for CN10KB.
2. Add/del/update interface function for exact match table.

Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: Use hashed field in MCAM key

CN10KB variant of CN10K series of silicons supports
a new feature where in a large protocol field
(eg 128bit IPv6 DIP) can be condensed into a small
hashed 32bit data. This saves a lot of space in MCAM key
and allows user to add more protocol fields into the filter.
A max of two such protocol data can be hashed.
This patch adds support for hashing IPv6 SIP and/or DIP.

Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Revert "Merge branch 'octeontx2-af-next'"

This reverts commit 2ef8e39f58f08589ab035223c2687830c0eba30f, reversing
changes made to e7ce9fc9ad38773b660ef663ae98df4f93cb6a37.

There are build warnings here which break the normal
build due to -Werror. Ratheesh was nice enough to quickly
follow up with fixes but didn't hit all the warnings I
see on GCC 12 so to unlock net-next from taking patches
let get this series out for now.

Link: https://lore.kernel.org/r/20220707013201.1372433-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: Exact match scan from kex profile

CN10KB silicon supports exact match table. Scanning KEX
profile should check for exact match feature is enabled
and then set profile masks properly.

These kex profile masks are required to configure NPC
MCAM drop rules. If there is a miss in exact match table,
these drop rules will drop those packets.

Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Exact match support

CN10KB silicon has support for exact match table. This table
can be used to match maimum 64 bit value of KPU parsed output.
Hit/non hit in exact match table can be used as a KEX key to
NPC mcam.

This patch makes use of Exact match table to increase number of
DMAC filters supported. NPC mcam is no more need for each of these
DMAC entries as will be populated in Exact match table.

This patch implements following

1. Initialization of exact match table only for CN10KB.
2. Add/del/update interface function for exact match table.

Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Use hashed field in MCAM key

CN10KB variant of CN10K series of silicons supports
a new feature where in a large protocol field
(eg 128bit IPv6 DIP) can be condensed into a small
hashed 32bit data. This saves a lot of space in MCAM key
and allows user to add more protocol fields into the filter.
A max of two such protocol data can be hashed.
This patch adds support for hashing IPv6 SIP and/or DIP.

Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

treewide: Replace zero-length arrays with flexible-array members

There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should
no longer be used[2].

This code was transformed with the help of Coccinelle:
(next-20220214$ spatch --jobs $(getconf _NPROCESSORS_ONLN) --sp-file script.cocci --include-headers --dir . > output.patch)

@@
identifier S, member, array;
type T1, T2;
@@

struct S {
...
T1 member;
T2 array[
- 0
];
};

UAPI and wireless changes were intentionally excluded from this patch
and will be sent out separately.

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays

Link: https://github.com/KSPP/linux/issues/78
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

octeontx2-af: debugfs: Add channel and channel mask.

This patch is to dispaly channel and channel_mask for each RX
interface of NPC MCAM rule.

Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Increase number of reserved entries in KPU

With current KPU profile, we have 2 reserved entries which can
be loaded from firmware to parse custom headers. Adding changes
to increase these reserved entries to 6.
And also removed KPU entries for unused LTYPEs like
NPC_LT_LA_IH_8_ETHER, NPC_LT_LA_IH_4_ETHER, NPC_LT_LA_IH_2_ETHER

Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Optimize KPU1 processing for variable-length headers

Optimized KPU1 entry processing for variable-length custom L2 headers
of size 24B, 90B by
- Moving LA LTYPE parsing for 24B and 90B headers to PKIND.
- Removing LA flags assignment for 24B and 90B headers.
- Reserving a PKIND 55 to parse variable length headers.

Also, new mailbox(NPC_SET_PKIND) added to configure PKIND with
corresponding variable-length offset, mask, and shift count
(NPC_AF_KPUX_ENTRYX_ACTION0).

Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-pf: Add vlan-etype to ntuple filters

NPC extraction profile marks layer types
NPC_LT_LB_CTAG for CTAG and NPC_LT_LB_STAG_QINQ for
STAG after parsing input packet. Those layer types
can be used to install ntuple filters using
vlan-etype option. Below are the commands and
corresponding behavior with this patch in place.

> alias nt "ethtool -U eth0 flow-type ether"

> nt vlan 5 m 0xf000 action 0
Input packets with outer VLAN id as 5 i.e,
stag packets with VLAN id 5 and ctag packets with
VLAN id as 5 are hit.

> nt vlan-etype 0x8100 action 0
All input ctag packets with any VLAN id are hit.

> nt vlan-etype 0x88A8 action 0
All input stag packets with any VLAN id are hit.

> nt vlan-etype 0x8100 vlan 5 m 0xf000 action 0
All input ctag packets with VLAN id 5 are hit.

> nt vlan-etype 0x88A8 vlan 5 m 0xf000 action 0
All input stag packets with VLAN id 5 are hit.

Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Fix inconsistent license text

Fixed inconsistent license text across the RVU admin
function driver.

Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Fix PKIND overlap between LBK and LMAC interfaces

Currently PKINDs are not assigned to LBK channels.
The default value of LBK_CHX_PKIND (channel to PKIND mapping) register
is zero, which is resulting in a overlap of pkind between LBK and CGX
LMACs. When KPU1 parser config is modified when PTP timestamping is
enabled on the CGX LMAC interface it is impacting traffic on LBK
interfaces as well.

This patch fixes the issue by reserving the PKIND#0 for LBK devices.
CGX mapped PF pkind starts from 1 and also fixes the max pkind available.

Fixes: 421572175ba5 ("octeontx2-af: Support to enable/disable HW timestamping")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: add support for multicast/promisc packet replication feature

Currently, multicast packet filtering is accomplished by installing
MCAM rule that matches all-multicast MAC address and has its
NPC_RX_ACTION set to unicast to PF. Similarly promisc feature is
achieved by installing MCAM rule that matches all the traffic received
by the channel and unicast the packets to PF. This approach only applies
to PF and is not scalable across VFs.

This patch adds support for PF/VF multicast and promisc feature by
reserving NIX_RX_MCE_S entries from the global MCE list allocated
during NIX block initialization. The NIX_RX_MCE_S entries create a
linked list with a flag indicating the end of the list, and each entry
points to a PF_FUNC (either PF or VF). When a packet NPC_RX_ACTION is
set to MCAST, the corresponding NIX_RX_MCE_S list is traversed and the
packet is queued to each PF_FUNC available on the list.

The PF or VF driver adds the multicast/promisc packet match entry and
updates the MCE list with correspondng PF_FUNC. When a PF or VF interface
is disabled, the corresponding NIX_RX_MCE_S entry is removed from the
MCE list and the MCAM entry will be disabled if the list is empty.

Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Update the default KPU profile and fixes

Add support for parsing following
1. NGIO
2. PPPOE
3. 24 byte custom L2 header
4. CPT Header
5. Fragmented CPT packets
6. VLAN EXDSA

Fix for
1. EDSA VLAN parsing
2. Enhance FDSA
3. CPT Header parsing

Remove ITAG support

Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@marvell.com>
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: support for coalescing KPU profiles

Adding support to load a new type of KPU image, known as coalesced/
consolidated KPU image via firmware database. This image is a
consolidation of multiple KPU profiles into a single image.

During kernel bootup this coalesced image will be read via
firmware database and only the relevant KPU profile will be loaded.
Existing functionality of loading single KPU/MKEX profile
is intact as the images are differentiated based on the image signature.

Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@marvell.com>
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: adding new lt def registers support

CN10k introduces following new LT DEF registers:
1. APAD (alignment padding) LT DEF registers are
enhancement to existing apad calculation algorithm
where not just ipv4 and ipv6 but also other protocols
can be matched and required alignment can be added by NIX.

2. ET LT DEF register defines layer information in NPC_RESULT_S
to identify the Ethertype location in L2 header. Used for
Ethertype overwriting in inline IPsec flow.

This patch adds required structures and some header changes. Also
strict version check (based on minor field) is imposed to highlight
version mismatch between the kernel headers and KPU profile.

Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Jerin Jacob Kollanukkaran <jerinj@marvell.com>
Signed-off-by: Kiran Kumar Kokkilagadda <kirankumark@marvell.com>
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: add support for custom KPU entries

Add ability to load a set of custom KPU entries. This
allows for flexible support for custom protocol parsing.

AF driver will attempt to load the profile and verify if it can fit
hardware capabilities. If not, it will revert to the built-in profile.

Next it will replace the first KPU_MAX_CST_LT (2) entries in each KPU
in default profile with entries read from the profile image.
The built-in profile should always contain KPU_MAX_CSR_LT first no-match
entries and AF driver will disable those in the KPU unless custom
profile is loaded.

Profile file contains also a list of default protocol overrides to
allow for custom protocols to be used there.

Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-pf: Add ip tos and ip proto icmp/icmpv6 flow offload support

Add support for programming the HW MCAM match key with IP tos, IP(v6)
proto icmp/icmpv6, allowing flow offload rules to be installed using
those fields. The NPC HW extracts layer type, which will be used as a
matching criteria for different IP protocols.

The ethtool n-tuple filter logic has been updated to parse the IP tos
and l4proto for HW offloading. l4proto tcp/udp/sctp/ah/esp/icmp are
supported. See example usage below.

Ex: Redirect l4proto icmp to vf 0 queue 0
ethtool -U eth0 flow-type ip4 l4proto 1 action vf 0 queue 0

Ex: Redirect flow with ip tos 8 to vf 0 queue 0
ethtool -U eth0 flow-type ip4 tos 8 vf 0 queue 0

Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: refactor function npc_install_flow for default entry

This patch refactors npc_install_flow function to install AF
installed default MCAM entries similar to other MCAM entries
installed by PF/VF. As a result the code would be more readable
and easy to maintain. Modified npc_verify_entry and npc_verify_channel
to properly check MCAM rules installed by AF.

Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-pf: Add flow classification using IP next level protocol

This patch adds support to install flow rules using ipv4 proto or
ipv6 next header field to distinguish between tcp/udp/sctp/esp/ah
flows when user doesn't specify the other match creteria related to
the flow such as tcp/udp/sctp source port and destination port, ah/esp
spi value. This is achieved by matching the layer type extracted by
NPC HW into the search key. Modified the driver to use Ethertype as
match criteria when user doesn't specify source IP address and dest
IP address. The esp/ah flow rule matching using security parameter
index (spi) is not supported as of now since the field is not extracted
into MCAM search key. Modified npc_check_field function to return bool.

Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20210111112537.3277-1-naveenm@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-pf: Add support for SR-IOV management functions

This patch adds support for ndo_set_vf_mac, ndo_set_vf_vlan
and ndo_get_vf_config handlers. The traffic redirection
based on the VF mac address or vlan id is done by installing
MCAM rules. Reserved RX_VTAG_TYPE7 in each NIXLF for VF VLAN
which strips the VLAN tag from ingress VLAN traffic. The NIX PF
allocates two MCAM entries for VF VLAN feature, one used for
ingress VTAG strip and another entry for egress VTAG insertion.

This patch also updates the MAC address in PF installed VF VLAN
rule upon receiving nix_lf_start_rx mbox request for VF since
Administrative Function driver will assign a valid MAC addr
in nix_lf_start_rx function.

Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Co-developed-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: Add mbox messages to install and delete MCAM rules

Added new mailbox messages to install and delete MCAM rules.
These mailbox messages will be used for adding/deleting ethtool
n-tuple filters by NIX PF. The installed MCAM rules are stored
in a list that will be traversed later to delete the MCAM entries
when the interface is brought down or when PCIe FLR is received.
The delete mailbox supports deleting a single MCAM entry or range
of entries or all the MCAM entries owned by the pcifunc. Each MCAM
entry can be associated with a HW match stat entry if the mailbox
requester wants to check the hit count for debugging.

Modified adding default unicast DMAC match rule using install
flow API. The default unicast DMAC match entry installed by
Administrative Function is saved and can be changed later by the
mailbox user to fit additional fields, or the default MCAM entry
rule action can be used for other flow rules installed later.

Modified rvu_mbox_handler_nix_lf_free mailbox to add a flag to
disable or delete the MCAM entries. The MCAM entries are disabled
when the interface is brought down and deleted in FLR handler.
The disabled MCAM entries will be re-enabled when the interface
is brought up again.

Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: Generate key field bit mask from KEX profile

Key Extraction(KEX) profile decides how the packet metadata such as
layer information and selected packet data bytes at each layer are
placed in MCAM search key. This patch reads the configured KEX profile
parameters to find out the bit position and bit mask for each field.
The information is used when programming the MCAM match data by SW
to match a packet flow and take appropriate action on the flow. This
patch also verifies the mandatory fields such as channel and DMAC
are not overwritten by the KEX configuration of other fields.

Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: Modify default KEX profile to extract TX packet fields

The current default Key Extraction(KEX) profile can only use RX
packet fields while generating the MCAM search key. The profile
can't be used for matching TX packet fields. This patch modifies
the default KEX profile to add support for extracting TX packet
fields into MCAM search key. Enabled Tx KPU packet parsing by
configuring TX PKIND in tx_parse_cfg.

Modified the KEX profile to extract 2 bytes of VLAN TCI from an
offset of 2 bytes from LB_PTR. The LB_PTR points to the byte offset
where the VLAN header starts. The NPC KPU parser profile has been
modified to point LB_PTR to the starting byte offset of VLAN header
which points to the tpid field.

Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: add parser support for NAT-T-ESP

Add support for NAT-T-ESP to KPU parser configuration. NAT ESP is a UDP
based protocol. So move ESP to LE so that both UDP and ESP can be
extracted.

Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Acked-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: add parser support for Forward DSA

Marvell Prestera switches supports distributed switch architecture
by inserting Forward DSA tag of 4 bytes right after ethernet SMAC.
This tag don't have a tpid field.

This patch provides parser and extraction support for the same.
Default ldata extraction profile added for FDSA such that Src_port
is extracted and placed inplace of vlanid field. Like extended DSA
and eDSA tags,a special PKIND of 62 is used for this tag.

Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Acked-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: cleanup KPU config data

Refactor KPU related NPC code gathering all configuration data in a
structured format and putting it in one place (npc_profile.h).
This increases readability and makes it easier to extend the profile
configuration (as opposed to jumping between multiple header and source
files).

To do this:
* Gather all KPU profile related data into a single adapter struct.
* Convert the built-in MKEX definition to a structured one to streamline
the MKEX loading.
* Convert LT default register configuration into a structure, keeping
default protocol settings in same file where identifiers for those
protocols are defined.
* Add a single point for KPU profile loading, so that its source may
change in the future once proper interfaces for loading such config
are in place.

Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Acked-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: fix LD CUSTOM LTYPE aliasing

Since LD contains LTYPE definitions tweaked toward efficient
NIX_AF_RX_FLOW_KEY_ALG(0..31)_FIELD(0..4) usage, the original location
of NPC_LT_LD_CUSTOM0/1 was aliased with MPLS_IN_* definitions.
Moving custom frame to value 6 and 7 removes the aliasing at the cost of
custom frames being also considered when TCP/UDP RSS algo is configured.

However since the goal of CUSTOM frames is to classify them to a
separate set of RQs, this cost is acceptable.

Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Acked-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Constify npc_kpu_profile_{action,cam}

These are never modified, so constify them to allow the compiler to
place them in read-only memory. This moves about 25kB to read-only
memory as seen by the output of the size command.

Before:
text data bss dec hex filename
296203 65464 1248 362915 589a3 drivers/net/ethernet/marvell/octeontx2/af/octeontx2_af.ko

After:
text data bss dec hex filename
321003 40664 1248 362915 589a3 drivers/net/ethernet/marvell/octeontx2/af/octeontx2_af.ko

Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Use the correct style for SPDX License Identifier

This patch corrects the SPDX License Identifier style in
header files related to Marvell OcteonTX2 network devices.
It uses an expilict block comment for the SPDX License
Identifier.

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Update NPC KPU packet parsing profile

Updated NPC KPU packet parsing profile with support for following

- Fragmentation support for IPv4 IPv6 outer header
- NIX instruction header support
- QinQ with TPID of 0x8100 as non inner most vlan tag, as legacy
network equipments still generate QinQ packets with this configuration.
- To better support RSS for tunnelled packets, udp based tunnel
protocols such as vxlan, vxlan-gpe, geneve and gtpu are now
captured into a separate layer E. Consequently, the inner
packet headers are pushed one layer down to LF, LG, and LH
accordingly.
- Support for rfc7510 mpls in udp. Up to 4 MPLS labels can be parsed
and captured in one layer LE.
- Parser support for DSA, extended DSA and eDSA tags right after
ethernet header by Marvell SOHO and Falcon switches. For extended
DSA and eDSA tags, a special PKIND of 62 is used, as these tags don't
contain a tpid field.
- Higig2 protocol header parsing support, added a NPC_LT_LA_HIGIG2_ETHER
for a combined header of HIGIG2 and Ethernet. Add a
NPC_LT_LA_IH_NIX_HIGIG2_ETHER for a combined header of nix_ih,
HIGIG2 and Ethernet on egress side. Also added 2 upper flags in LA to
indicate the presence of nix_ih and HIGIG2.

Other changes include
- IPv4.TTL==0 IPv6.HLIM==0 check
- Per RFC 1858, mark fragment offset == 1 as error
- TCP invalid flags check
- Separate error codes for outer and inner IPv4 checksum errors.
- Fix a parser error when KPU parses incoming IPSec ESP and AH packets
- NPC vtag capture/strip hardware expect tag pointer to point to
tpid/ethertype instead of tci. So move lb_ptr to point to tpid/ethertype.
- Fix npc parser error when parsing udp packets that don't have any payload.
- For a single MCAM entry to match on packets with one or stacked vlan tags
combine NPC_LT_LB_STAG and NPC_LT_LB_QINQ to NPC_LT_LB_STAG_QINQ.
- NVGRE to have a separate ltype LD_NVGRE instead of combined with LD_GRE.
- Reserve top LD/LTYPEs to support custom KPU profile fields.

Signed-off-by: Hao Zheng <haoz@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Enable mkex profile

The following set of NPC registers allow the driver to configure NPC
to generate different key value schemes to compare against packet
payload in MCAM search.

NPC_AF_INTF(0..1)_KEX_CFG
NPC_AF_KEX_LDATA(0..1)_FLAGS_CFG
NPC_AF_INTF(0..1)_LID(0..7)_LT(0..15)_LD(0..1)_CFG
NPC_AF_INTF(0..1)_LDATA(0..1)_FLAGS(0..15)_CFG

Currently, the AF driver populates these registers to
configure the default values to address the most common
use cases such as key generation for channel number + DMAC.

The secure firmware stores different configuration
value of these registers to enable different NPC use case
along with the name for the lookup.

Patch loads profile binary from secure firmware over
the exiting CGX mailbox interface and apply the profile.

AF driver shall fall back to the default configuration
in case of any errors.

The AF consumer driver can know the selected profile
on response to NPC_GET_KEX_CFG mailbox by introducing
mkex_pfl_name in the struct npc_get_kex_cfg_rsp.

Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Add support for stripping STAG/CTAG

This works by shadowing existing UCAST MCAM entry
with a new one additionally matching either NPC_LT_LB_CTAG
or NPC_LT_LB_STAG. For this to fully work one needs to
send properly configured NIX_VTAG_CFG message afterwards i.e with
strip and capture enabled and type set to 0.

On receiving tagged packet NIX will remove outer VLAN and capture
TCI in NIX_RX_PARSE_S.

Also simplified RX Vtag configuration flow
With this setting STRIP/CAPTURE VTAG actions separately would be
possible. Following combinations are possible: STRIP,
STRIP and CAPTURE, CAPTURE or nothing (0 disables respective actions).

Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Install ucast and bcast pkt forwarding rules

Upon NIXLF_ALLOC install a unicast forwarding rule in NPC MCAM
like below
- Match pkt DMAC with NIXLF attached PF/VF's MAC address.
- Ingress channel
- Action is UCAST
- Forward to PF_FUNC of this NIXLF
And broadcast pkt forwarding rule as
- Match L2B bit in MCAM search key
- Ingress channel
- Action is UCAST, for now, later it will be changed to MCAST.
Only PFs can install this rule

Upon NIXLF_FREE disable all MCAM entries in use by that NIXLF.

Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Config NPC KPU engines with parser profile

This patch configures all 16 KPUs and iKPU (pkinds) with
the KPU parser profile defined in npc_profile.h. Each KPU
engine has a 128 entry CAM, only CAM entries which are listed
in the profile are enabled and rest are left disabled.

Also
- Memory is allocated for pkind's bitmap and PFFUNC, interface
channel mapping.
- Added all CSR offsets of NPC HW block.

Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

octeontx2-af: Add NPC KPU profile

NPC block is responsible for parsing and forwarding
packets to different NIXLFs. NPC has 16 KPU engines
(Kangaroo parse engine) and one iKPU which represents
pkinds. Each physical port either CGX/LBK is assigned
a pkind and upon receiving a packet HW takes that port's
pkind and starts parsing as per the KPU engines config.

This patch adds header files which contain configuration
profile/array for each of the iKPU and 16 KPU engines.

Signed-off-by: Hao Zheng <hao.zheng@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>