ice: work on pre-XDP prog frag count

Fix an OOM panic in XDP_DRV mode when a XDP program shrinks a
multi-buffer packet by 4k bytes and then redirects it to an AF_XDP
socket.

Since support for handling multi-buffer frames was added to XDP, usage
of bpf_xdp_adjust_tail() helper within XDP program can free the page
that given fragment occupies and in turn decrease the fragment count
within skb_shared_info that is embedded in xdp_buff struct. In current
ice driver codebase, it can become problematic when page recycling logic
decides not to reuse the page. In such case, __page_frag_cache_drain()
is used with ice_rx_buf::pagecnt_bias that was not adjusted after
refcount of page was changed by XDP prog which in turn does not drain
the refcount to 0 and page is never freed.

To address this, let us store the count of frags before the XDP program
was executed on Rx ring struct. This will be used to compare with
current frag count from skb_shared_info embedded in xdp_buff. A smaller
value in the latter indicates that XDP prog freed frag(s). Then, for
given delta decrement pagecnt_bias for XDP_DROP verdict.

While at it, let us also handle the EOP frag within
ice_set_rx_bufs_act() to make our life easier, so all of the adjustments
needed to be applied against freed frags are performed in the single
place.

Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-5-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

ice: use VLAN proto from ring packet context in skb path

VLAN proto, used in ice XDP hints implementation is stored in ring packet
context. Utilize this value in skb VLAN processing too instead of checking
netdev features.

At the same time, use vlan_tci instead of vlan_tag in touched code,
because VLAN tag often refers to VLAN proto and VLAN TCI combined,
while in the code we clearly store only VLAN TCI.

Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-12-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

ice: Implement VLAN tag hint

Implement .xmo_rx_vlan_tag callback to allow XDP code to read
packet's VLAN tag.

At the same time, use vlan_tci instead of vlan_tag in touched code,
because VLAN tag often refers to VLAN proto and VLAN TCI combined,
while in the code we clearly store only VLAN TCI.

Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-11-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

ice: Introduce ice_xdp_buff

In order to use XDP hints via kfuncs we need to put
RX descriptor and miscellaneous data next to xdp_buff.
Same as in hints implementations in other drivers, we achieve
this through putting xdp_buff into a child structure.

Currently, xdp_buff is stored in the ring structure,
so replace it with union that includes child structure.
This way enough memory is available while existing XDP code
remains isolated from hints.

Minimum size of the new child structure (ice_xdp_buff) is exactly
64 bytes (single cache line). To place it at the start of a cache line,
move 'next' field from CL1 to CL4, as it isn't used often. This still
leaves 192 bits available in CL3 for packet context extensions.

Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-5-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

ice: Make ptype internal to descriptor info processing

Currently, rx_ptype variable is used only as an argument
to ice_process_skb_fields() and is computed
just before the function call.

Therefore, there is no reason to pass this value as an argument.
Instead, remove this argument and compute the value directly inside
ice_process_skb_fields() function.

Also, separate its calculation into a short function, so the code
can later be reused in .xmo_() callbacks.

Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-4-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

ice: Micro-optimize .ndo_xdp_xmit() path

After the recent mbuf changes, ice_xmit_xdp_ring() became a 3-liner.
It makes no sense to keep it global in a different file than its caller.
Move it just next to the sole call site and mark static. Also, it
doesn't need a full xdp_convert_frame_to_buff(). Save several cycles
and fill only the fields used by __ice_xmit_xdp_ring() later on.
Finally, since it doesn't modify @xdpf anyhow, mark the argument const
to save some more (whole -11 bytes of .text! :D).

Thanks to 1 jump less and less calcs as well, this yields as many as
6.7 Mpps per queue. `xdp.data_hard_start = xdpf` is fully intentional
again (see xdp_convert_buff_to_frame()) and just works when there are
no source device's driver issues.

Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20230210170618.1973430-7-alexandr.lobakin@intel.com

ice: Fix freeing XDP frames backed by Page Pool

As already mentioned, freeing any &xdp_frame via page_frag_free() is
wrong, as it assumes the frame is backed by either an order-0 page or
a page with no "patrons" behind them, while in fact frames backed by
Page Pool can be redirected to a device, which's driver doesn't use it.
Keep storing a pointer to the raw buffer and then freeing it
unconditionally via page_frag_free() for %XDP_TX frames, but introduce
a separate type in the enum for frames coming through .ndo_xdp_xmit(),
and free them via xdp_return_frame_bulk(). Note that saving xdpf as
xdp_buff->data_hard_start is intentional and is always true when
everything is configured properly.
After this change, %XDP_REDIRECT from a Page Pool based driver to ice
becomes zero-alloc as it should be and horrendous 3.3 Mpps / queue
turn into 6.6, hehe.

Let it go with no "Fixes:" tag as it spans across good 5+ commits and
can't be trivially backported.

Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20230210170618.1973430-6-alexandr.lobakin@intel.com

ice: Add support for XDP multi-buffer on Tx side

Similarly as for Rx side in previous patch, logic on XDP Tx in ice
driver needs to be adjusted for multi-buffer support. Specifically, the
way how HW Tx descriptors are produced and cleaned.

Currently, XDP_TX works on strict ring boundaries, meaning it sets RS
bit (on producer side) / looks up DD bit (on consumer/cleaning side)
every quarter of the ring. It means that if for example multi buffer
frame would span across the ring quarter boundary (say that frame
consists of 4 frames and we start from 62 descriptor where ring is sized
to 256 entries), RS bit would be produced in the middle of multi buffer
frame, which would be a broken behavior as it needs to be set on the
last descriptor of the frame.

To make it work, set RS bit at the last descriptor from the batch of
frames that XDP_TX action was used on and make the first entry remember
the index of last descriptor with RS bit set. This way, cleaning side
can take the index of descriptor with RS bit, look up DD bit's presence
and clean from first entry to last.

In order to clean up the code base introduce the common ice_set_rs_bit()
which will return index of descriptor that got RS bit produced on so
that standard driver can store this within proper ice_tx_buf and ZC
driver can simply ignore return value.

Co-developed-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-12-maciej.fijalkowski@intel.com

ice: Add support for XDP multi-buffer on Rx side

Ice driver needs to be a bit reworked on Rx data path in order to
support multi-buffer XDP. For skb path, it currently works in a way that
Rx ring carries pointer to skb so if driver didn't manage to combine
fragmented frame at current NAPI instance, it can restore the state on
next instance and keep looking for last fragment (so descriptor with EOP
bit set). What needs to be achieved is that xdp_buff needs to be
combined in such way (linear + frags part) in the first place. Then skb
will be ready to go in case of XDP_PASS or BPF program being not present
on interface. If BPF program is there, it would work on multi-buffer
XDP. At this point xdp_buff resides directly on Rx ring, so given the
fact that skb will be built straight from xdp_buff, there will be no
further need to carry skb on Rx ring.

Besides removing skb pointer from Rx ring, lots of members have been
moved around within ice_rx_ring. First and foremost reason was to place
rx_buf with xdp_buff on the same cacheline. This means that once we
touch rx_buf (which is a preceding step before touching xdp_buff),
xdp_buff will already be hot in cache. Second thing was that xdp_rxq is
used rather rarely and it occupies a separate cacheline, so maybe it is
better to have it at the end of ice_rx_ring.

Other change that affects ice_rx_ring is the introduction of
ice_rx_ring::first_desc. Its purpose is twofold - first is to propagate
rx_buf->act to all the parts of current xdp_buff after running XDP
program, so that ice_put_rx_buf() that got moved out of the main Rx
processing loop will be able to tak an appriopriate action on each
buffer. Second is for ice_construct_skb().

ice_construct_skb() has a copybreak mechanism which had an explicit
impact on xdp_buff->skb conversion in the new approach when legacy Rx
flag is toggled. It works in a way that linear part is 256 bytes long,
if frame is bigger than that, remaining bytes are going as a frag to
skb_shared_info.

This means while memcpying frags from xdp_buff to newly allocated skb,
care needs to be taken when picking the destination frag array entry.
Upon the time ice_construct_skb() is called, when dealing with
fragmented frame, current rx_buf points to the *last* fragment, but
copybreak needs to be done against the first one. That's where
ice_rx_ring::first_desc helps.

When frame building spans across NAPI polls (DD bit is not set on
current descriptor and xdp->data is not NULL) with current Rx buffer
handling state there might be some problems.
Since calls to ice_put_rx_buf() were pulled out of the main Rx
processing loop and were scoped from cached_ntc to current ntc, remember
that now mentioned function relies on rx_buf->act, which is set within
ice_run_xdp(). ice_run_xdp() is called when EOP bit was found, so
currently we could put Rx buffer with rx_buf->act being *uninitialized*.
To address this, change scoping to rely on first_desc on both boundaries
instead.

This also implies that cleaned_count which is used as an input to
ice_alloc_rx_buffers() and tells how many new buffers should be refilled
has to be adjusted. If it stayed as is, what could happen is a case
where ntc would go over ntu.

Therefore, remove cleaned_count altogether and use against allocing
routine newly introduced ICE_RX_DESC_UNUSED() macro which is an
equivalent of ICE_DESC_UNUSED() dedicated for Rx side and based on
struct ice_rx_ring::first_desc instead of next_to_clean.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-11-maciej.fijalkowski@intel.com

ice: Inline eop check

This might be in future used by ZC driver and might potentially yield a
minor performance boost. While at it, constify arguments that
ice_is_non_eop() takes, since they are pointers and this will help compiler
while generating asm.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-6-maciej.fijalkowski@intel.com

ice: Add hot path support for 802.1Q and 802.1ad VLAN offloads

Currently the driver only supports 802.1Q VLAN insertion and stripping.
However, once Double VLAN Mode (DVM) is fully supported, then both 802.1Q
and 802.1ad VLAN insertion and stripping will be supported. Unfortunately
the VSI context parameters only allow for one VLAN ethertype at a time
for VLAN offloads so only one or the other VLAN ethertype offload can be
supported at once.

To support this, multiple changes are needed.

Rx path changes:

[1] In DVM, the Rx queue context l2tagsel field needs to be cleared so
the outermost tag shows up in the l2tag2_2nd field of the Rx flex
descriptor. In Single VLAN Mode (SVM), the l2tagsel field should remain
1 to support SVM configurations.

[2] Modify the ice_test_staterr() function to take a __le16 instead of
the ice_32b_rx_flex_desc union pointer so this function can be used for
both rx_desc->wb.status_error0 and rx_desc->wb.status_error1.

[3] Add the new inline function ice_get_vlan_tag_from_rx_desc() that
checks if there is a VLAN tag in l2tag1 or l2tag2_2nd.

[4] In ice_receive_skb(), add a check to see if NETIF_F_HW_VLAN_STAG_RX
is enabled in netdev->features. If it is, then this is the VLAN
ethertype that needs to be added to the stripping VLAN tag. Since
ice_fix_features() prevents CTAG_RX and STAG_RX from being enabled
simultaneously, the VLAN ethertype will only ever be 802.1Q or 802.1ad.

Tx path changes:

[1] In DVM, the VLAN tag needs to be placed in the l2tag2 field of the Tx
context descriptor. The new define ICE_TX_FLAGS_HW_OUTER_SINGLE_VLAN was
added to the list of tx_flags to handle this case.

[2] When the stack requests the VLAN tag to be offloaded on Tx, the
driver needs to set either ICE_TX_FLAGS_HW_OUTER_SINGLE_VLAN or
ICE_TX_FLAGS_HW_VLAN, so the tag is inserted in l2tag2 or l2tag1
respectively. To determine which location to use, set a bit in the Tx
ring flags field during ring allocation that can be used to determine
which field to use in the Tx descriptor. In DVM, always use l2tag2,
and in SVM, always use l2tag1.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: propagate xdp_ring onto rx_ring

With rings being split, it is now convenient to introduce a pointer to
XDP ring within the Rx ring. For XDP_TX workloads this means that
xdp_rings array access will be skipped, which was executed per each
processed frame.

Also, read the XDP prog once per NAPI and if prog is present, set up the
local xdp_ring pointer. Reading prog a single time was discussed in [1]
with some concern raised by Toke around dispatcher handling and having
the need for going through the RCU grace period in the ndo_bpf driver
callback, but ice currently is torning down NAPI instances regardless of
the prog presence on VSI.

Although the pointer to XDP ring introduced to Rx ring makes things a
lot slimmer/simpler, I still feel that single prog read per NAPI
lifetime is beneficial.

Further patch that will introduce the fallback path will also get a
profit from that as xdp_ring pointer will be set during the XDP rings
setup.

[1]: https://lore.kernel.org/bpf/87k0oseo6e.fsf@toke.dk/

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: split ice_ring onto Tx/Rx separate structs

While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.

Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.

Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.

Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.

Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.

Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: report hash type such as L2/L3/L4

The hardware is reporting the type of the hash used for RSS
as a PTYPE field in the receive descriptor. Use this value to set
the skb packet hash type by extending the hash type table to
cover all 10-bits of possible values (requiring some variables
to be changed from u8 to u16), and then use that table to convert
to one of the possible values in enum pkt_hash_types.

While we're here, remove the unused ptype struct value, which
makes table init easier for the zero entries, and use ranged
initializer to remove a bunch of code (works with gcc and clang).

Without this change, the kernel will recalculate the hash in software,
which can consume extra CPU cycles.

Co-developed-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Rename build_ctob to ice_build_ctob

To make the function easier to identify as being part of the ice driver,
prepend ice to the function name.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Fix casting issues

Change min() macros to min_t() which has compare type specified and it
helps avoid precision loss.

In some cases there was precision loss during calls or assignments.
Some fields in structs were unnecessarily large and gave multiple
warnings.

There were also some minor type differences which are now fixed as well as
some cases where a simple cast was needed.

Callers were were passing data that is a u16 to
ice_sched_cfg_node_bw_alloc() but the function was truncating that to a u8.
Fix that by changing the function to take a u16.

Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Move common functions to ice_txrx_lib.c

In preparation of AF XDP, move functions that will be used both by skb and
zero-copy paths to a new file called ice_txrx_lib.c. This allows us to
avoid using ifdefs to control the staticness of said functions.

Move other functions (ice_rx_csum, ice_rx_hash and ice_ptype_to_htype)
called only by the moved ones to the new file as well.

Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>