ice: remove redundant xdp_rxq_info registration

xdp_rxq_info struct can be registered by drivers via two functions -
xdp_rxq_info_reg() and __xdp_rxq_info_reg(). The latter one allows
drivers that support XDP multi-buffer to set up xdp_rxq_info::frag_size
which in turn will make it possible to grow the packet via
bpf_xdp_adjust_tail() BPF helper.

Currently, ice registers xdp_rxq_info in two spots:
1) ice_setup_rx_ring() // via xdp_rxq_info_reg(), BUG
2) ice_vsi_cfg_rxq() // via __xdp_rxq_info_reg(), OK

Cited commit under fixes tag took care of setting up frag_size and
updated registration scheme in 2) but it did not help as
1) is called before 2) and as shown above it uses old registration
function. This means that 2) sees that xdp_rxq_info is already
registered and never calls __xdp_rxq_info_reg() which leaves us with
xdp_rxq_info::frag_size being set to 0.

To fix this misbehavior, simply remove xdp_rxq_info_reg() call from
ice_setup_rx_ring().

Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-7-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

ice: work on pre-XDP prog frag count

Fix an OOM panic in XDP_DRV mode when a XDP program shrinks a
multi-buffer packet by 4k bytes and then redirects it to an AF_XDP
socket.

Since support for handling multi-buffer frames was added to XDP, usage
of bpf_xdp_adjust_tail() helper within XDP program can free the page
that given fragment occupies and in turn decrease the fragment count
within skb_shared_info that is embedded in xdp_buff struct. In current
ice driver codebase, it can become problematic when page recycling logic
decides not to reuse the page. In such case, __page_frag_cache_drain()
is used with ice_rx_buf::pagecnt_bias that was not adjusted after
refcount of page was changed by XDP prog which in turn does not drain
the refcount to 0 and page is never freed.

To address this, let us store the count of frags before the XDP program
was executed on Rx ring struct. This will be used to compare with
current frag count from skb_shared_info embedded in xdp_buff. A smaller
value in the latter indicates that XDP prog freed frag(s). Then, for
given delta decrement pagecnt_bias for XDP_DROP verdict.

While at it, let us also handle the EOP frag within
ice_set_rx_bufs_act() to make our life easier, so all of the adjustments
needed to be applied against freed frags are performed in the single
place.

Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-5-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

ice: field prep conversion

Refactor ice driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.

This code was generated by the following coccinelle/spatch script and
then manually repaired.

Several places I changed to OR into a single variable with |= instead of
using a multi-line statement with trailing OR operators, as it
(subjectively) makes the code clearer.

A local variable vmvf_and_timeout was created and used to avoid multiple
logical ORs being __le16 converted, which shortened some lines and makes
the code cleaner.

Also clean up a couple of places where conversions were made to have the
code read more clearly/consistently.

@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)

@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)

Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Implement VLAN tag hint

Implement .xmo_rx_vlan_tag callback to allow XDP code to read
packet's VLAN tag.

At the same time, use vlan_tci instead of vlan_tag in touched code,
because VLAN tag often refers to VLAN proto and VLAN TCI combined,
while in the code we clearly store only VLAN TCI.

Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-11-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

ice: Introduce ice_xdp_buff

In order to use XDP hints via kfuncs we need to put
RX descriptor and miscellaneous data next to xdp_buff.
Same as in hints implementations in other drivers, we achieve
this through putting xdp_buff into a child structure.

Currently, xdp_buff is stored in the ring structure,
so replace it with union that includes child structure.
This way enough memory is available while existing XDP code
remains isolated from hints.

Minimum size of the new child structure (ice_xdp_buff) is exactly
64 bytes (single cache line). To place it at the start of a cache line,
move 'next' field from CL1 to CL4, as it isn't used often. This still
leaves 192 bits available in CL3 for packet context extensions.

Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-5-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

ice: Make ptype internal to descriptor info processing

Currently, rx_ptype variable is used only as an argument
to ice_process_skb_fields() and is computed
just before the function call.

Therefore, there is no reason to pass this value as an argument.
Instead, remove this argument and compute the value directly inside
ice_process_skb_fields() function.

Also, separate its calculation into a short function, so the code
can later be reused in .xmo_() callbacks.

Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-4-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

ice: remove ptp_tx ring parameter flag

Before performing a Tx timestamp in ice_stamp(), the driver checks a ptp_tx
ring variable to see if timestamping is enabled on that ring. This value is
set for all rings whenever userspace configures Tx timestamping.

Ostensibly this was done to avoid wasting cycles checking other fields when
timestamping has not been enabled. However, for Tx timestamps we already
get an individual per-SKB flag indicating whether userspace wants to
request a timestamp on that packet. We do not gain much by also having
a separate flag to check for whether timestamping was enabled.

In fact, the driver currently fails to restore the field after a PF reset.
Because of this, if a PF reset occurs, timestamps will be disabled.

Since this flag doesn't add value in the hotpath, remove it and always
provide a timestamp if the SKB flag has been set.

A following change will fix the reset path to properly restore user
timestamping configuration completely.

This went unnoticed for some time because one of the most common
applications using Tx timestamps, ptp4l, will reconfigure the socket as
part of its fault recovery logic.

Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

ice: recycle/free all of the fragments from multi-buffer frame

The ice driver caches next_to_clean value at the beginning of
ice_clean_rx_irq() in order to remember the first buffer that has to be
freed/recycled after main Rx processing loop. The end boundary is
indicated by first descriptor of frame that Rx processing loop has ended
its duties. Note that if mentioned loop ended in the middle of gathering
multi-buffer frame, next_to_clean would be pointing to the descriptor in
the middle of the frame BUT freeing/recycling stage will stop at the
first descriptor. This means that next iteration of ice_clean_rx_irq()
will miss the (first_desc, next_to_clean - 1) entries.

When running various 9K MTU workloads, such splats were observed:

[ 540.780716] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 540.787787] #PF: supervisor read access in kernel mode
[ 540.793002] #PF: error_code(0x0000) - not-present page
[ 540.798218] PGD 0 P4D 0
[ 540.800801] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 540.805231] CPU: 18 PID: 3984 Comm: xskxceiver Tainted: G W 6.3.0-rc7+ #96
[ 540.813619] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019
[ 540.824209] RIP: 0010:ice_clean_rx_irq+0x2b6/0xf00 [ice]
[ 540.829678] Code: 74 24 10 e9 aa 00 00 00 8b 55 78 41 31 57 10 41 09 c4 4d 85 ff 0f 84 83 00 00 00 49 8b 57 08 41 8b 4f 1c 65 8b 35 1a fa 4b 3f <48> 8b 02 48 c1 e8 3a 39 c6 0f 85 a2 00 00 00 f6 42 08 02 0f 85 98
[ 540.848717] RSP: 0018:ffffc9000f42fc50 EFLAGS: 00010282
[ 540.854029] RAX: 0000000000000004 RBX: 0000000000000002 RCX: 000000000000fffe
[ 540.861272] RDX: 0000000000000000 RSI: 0000000000000001 RDI: 00000000ffffffff
[ 540.868519] RBP: ffff88984a05ac00 R08: 0000000000000000 R09: dead000000000100
[ 540.875760] R10: ffff88983fffcd00 R11: 000000000010f2b8 R12: 0000000000000004
[ 540.883008] R13: 0000000000000003 R14: 0000000000000800 R15: ffff889847a10040
[ 540.890253] FS: 00007f6ddf7fe640(0000) GS:ffff88afdf800000(0000) knlGS:0000000000000000
[ 540.898465] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 540.904299] CR2: 0000000000000000 CR3: 000000010d3da001 CR4: 00000000007706e0
[ 540.911542] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 540.918789] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 540.926032] PKRU: 55555554
[ 540.928790] Call Trace:
[ 540.931276] <TASK>
[ 540.933418] ice_napi_poll+0x4ca/0x6d0 [ice]
[ 540.937804] ? __pfx_ice_napi_poll+0x10/0x10 [ice]
[ 540.942716] napi_busy_loop+0xd7/0x320
[ 540.946537] xsk_recvmsg+0x143/0x170
[ 540.950178] sock_recvmsg+0x99/0xa0
[ 540.953729] __sys_recvfrom+0xa8/0x120
[ 540.957543] ? do_futex+0xbd/0x1d0
[ 540.961008] ? __x64_sys_futex+0x73/0x1d0
[ 540.965083] __x64_sys_recvfrom+0x20/0x30
[ 540.969155] do_syscall_64+0x38/0x90
[ 540.972796] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[ 540.977934] RIP: 0033:0x7f6de5f27934

To fix this, set cached_ntc to first_desc so that at the end, when
freeing/recycling buffers, descriptors from first to ntc are not missed.

Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230531154457.3216621-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ice: Fix undersized tx_flags variable

As not all ICE_TX_FLAGS_* fit in current 16-bit limited
tx_flags field that was introduced in the Fixes commit,
VLAN-related information would be discarded completely.
As such, creating a vlan and trying to run ping through
would result in no traffic passing.

Fix that by refactoring tx_flags variable into flags only and
a separate variable that holds VLAN ID. As there is some space left,
type variable can fit between those two. Pahole reports no size
change to ice_tx_buf struct.

Fixes: aa1d3faf71a6 ("ice: Robustify cleaning/completing XDP Tx buffers")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ice: fix W=1 headers mismatch

make modules W=1 returns:
.../ice/ice_txrx_lib.c:448: warning: Function parameter or member 'first_idx' not described in 'ice_finalize_xdp_rx'
.../ice/ice_txrx.c:948: warning: Function parameter or member 'ntc' not described in 'ice_get_rx_buf'
.../ice/ice_txrx.c:1038: warning: Excess function parameter 'rx_buf' description in 'ice_construct_skb'

Fix these warnings by adding and deleting the deviant arguments.

Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Fixes: d7956d81f150 ("ice: Pull out next_to_clean bump out of ice_put_rx_buf()")
CC: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: fix rx buffers handling for flow director packets

Adding flow director filters stopped working correctly after
commit 2fba7dc5157b ("ice: Add support for XDP multi-buffer
on Rx side"). As a result, only first flow director filter
can be added, adding next filter leads to NULL pointer
dereference attached below.

Rx buffer handling and reallocation logic has been optimized,
however flow director specific traffic was not accounted for.
As a result driver handled those packets incorrectly since new
logic was based on ice_rx_ring::first_desc which was not set
in this case.

Fix this by setting struct ice_rx_ring::first_desc to next_to_clean
for flow director received packets.

[ 438.544867] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 438.551840] #PF: supervisor read access in kernel mode
[ 438.556978] #PF: error_code(0x0000) - not-present page
[ 438.562115] PGD 7c953b2067 P4D 0
[ 438.565436] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 438.569794] CPU: 0 PID: 0 Comm: swapper/0 Kdump: loaded Not tainted 6.2.0-net-bug #1
[ 438.577531] Hardware name: Intel Corporation M50CYP2SBSTD/M50CYP2SBSTD, BIOS SE5C620.86B.01.01.0005.2202160810 02/16/2022
[ 438.588470] RIP: 0010:ice_clean_rx_irq+0x2b9/0xf20 [ice]
[ 438.593860] Code: 45 89 f7 e9 ac 00 00 00 8b 4d 78 41 31 4e 10 41 09 d5 4d 85 f6 0f 84 82 00 00 00 49 8b 4e 08 41 8b 76
1c 65 8b 3d 47 36 4a 3f <48> 8b 11 48 c1 ea 36 39 d7 0f 85 a6 00 00 00 f6 41 08 02 0f 85 9c
[ 438.612605] RSP: 0018:ff8c732640003ec8 EFLAGS: 00010082
[ 438.617831] RAX: 0000000000000800 RBX: 00000000000007ff RCX: 0000000000000000
[ 438.624957] RDX: 0000000000000800 RSI: 0000000000000000 RDI: 0000000000000000
[ 438.632089] RBP: ff4ed275a2158200 R08: 00000000ffffffff R09: 0000000000000020
[ 438.639222] R10: 0000000000000000 R11: 0000000000000020 R12: 0000000000001000
[ 438.646356] R13: 0000000000000000 R14: ff4ed275d0daffe0 R15: 0000000000000000
[ 438.653485] FS: 0000000000000000(0000) GS:ff4ed2738fa00000(0000) knlGS:0000000000000000
[ 438.661563] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 438.667310] CR2: 0000000000000000 CR3: 0000007c9f0d6006 CR4: 0000000000771ef0
[ 438.674444] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 438.681573] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 438.688697] PKRU: 55555554
[ 438.691404] Call Trace:
[ 438.693857] <IRQ>
[ 438.695877] ? profile_tick+0x17/0x80
[ 438.699542] ice_msix_clean_ctrl_vsi+0x24/0x50 [ice]
[ 438.702571] ice 0000:b1:00.0: VF 1: ctrl_vsi irq timeout
[ 438.704542] __handle_irq_event_percpu+0x43/0x1a0
[ 438.704549] handle_irq_event+0x34/0x70
[ 438.704554] handle_edge_irq+0x9f/0x240
[ 438.709901] iavf 0000:b1:01.1: Failed to add Flow Director filter with status: 6
[ 438.714571] __common_interrupt+0x63/0x100
[ 438.714580] common_interrupt+0xb4/0xd0
[ 438.718424] iavf 0000:b1:01.1: Rule ID: 127 dst_ip: 0.0.0.0 src_ip 0.0.0.0 UDP: dst_port 4 src_port 0
[ 438.722255] </IRQ>
[ 438.722257] <TASK>
[ 438.722257] asm_common_interrupt+0x22/0x40
[ 438.722262] RIP: 0010:cpuidle_enter_state+0xc8/0x430
[ 438.722267] Code: 6e e9 25 ff e8 f9 ef ff ff 8b 53 04 49 89 c5 0f 1f 44 00 00 31 ff e8 d7 f1 24 ff 45
84 ff 0f 85 57 02 00 00 fb 0f 1f 44 00 00 <45> 85 f6 0f 88 85 01 00 00 49 63 d6 48 8d 04 52 48 8d 04 82 49 8d
[ 438.722269] RSP: 0018:ffffffff86003e50 EFLAGS: 00000246
[ 438.784108] RAX: ff4ed2738fa00000 RBX: ffbe72a64fc01020 RCX: 0000000000000000
[ 438.791234] RDX: 0000000000000000 RSI: ffffffff858d84de RDI: ffffffff85893641
[ 438.798365] RBP: 0000000000000002 R08: 0000000000000002 R09: 000000003158af9d
[ 438.805490] R10: 0000000000000008 R11: 0000000000000354 R12: ffffffff862365a0
[ 438.812622] R13: 000000661b472a87 R14: 0000000000000002 R15: 0000000000000000
[ 438.819757] cpuidle_enter+0x29/0x40
[ 438.823333] do_idle+0x1b6/0x230
[ 438.826566] cpu_startup_entry+0x19/0x20
[ 438.830492] rest_init+0xcb/0xd0
[ 438.833717] arch_call_rest_init+0xa/0x30
[ 438.837731] start_kernel+0x776/0xb70
[ 438.841396] secondary_startup_64_no_verify+0xe5/0xeb
[ 438.846449] </TASK>

Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: add support BIG TCP on IPv6

Enable sending BIG TCP packets on IPv6 in the ice driver using generic
ipv6_hopopt_jumbo_remove helper for stripping HBH header.

Tested:
netperf -t TCP_RR -H 2001:db8:0:f101::1 -- -r80000,80000 -O MIN_LATENCY,P90_LATENCY,P99_LATENCY,TRANSACTION_RATE

Tested on two different setups. In both cases, the following settings were
applied after loading the changed driver:

ip link set dev enp175s0f1np1 gso_max_size 130000
ip link set dev enp175s0f1np1 gro_max_size 130000
ip link set dev enp175s0f1np1 mtu 9000

First setup:
Before:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
134 279 410 3961.584

After:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
135 178 216 6093.404

The other setup:
Before:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
218 414 478 2944.765

After:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
146 238 266 4700.596

Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Micro-optimize .ndo_xdp_xmit() path

After the recent mbuf changes, ice_xmit_xdp_ring() became a 3-liner.
It makes no sense to keep it global in a different file than its caller.
Move it just next to the sole call site and mark static. Also, it
doesn't need a full xdp_convert_frame_to_buff(). Save several cycles
and fill only the fields used by __ice_xmit_xdp_ring() later on.
Finally, since it doesn't modify @xdpf anyhow, mark the argument const
to save some more (whole -11 bytes of .text! :D).

Thanks to 1 jump less and less calcs as well, this yields as many as
6.7 Mpps per queue. `xdp.data_hard_start = xdpf` is fully intentional
again (see xdp_convert_buff_to_frame()) and just works when there are
no source device's driver issues.

Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20230210170618.1973430-7-alexandr.lobakin@intel.com

ice: Fix freeing XDP frames backed by Page Pool

As already mentioned, freeing any &xdp_frame via page_frag_free() is
wrong, as it assumes the frame is backed by either an order-0 page or
a page with no "patrons" behind them, while in fact frames backed by
Page Pool can be redirected to a device, which's driver doesn't use it.
Keep storing a pointer to the raw buffer and then freeing it
unconditionally via page_frag_free() for %XDP_TX frames, but introduce
a separate type in the enum for frames coming through .ndo_xdp_xmit(),
and free them via xdp_return_frame_bulk(). Note that saving xdpf as
xdp_buff->data_hard_start is intentional and is always true when
everything is configured properly.
After this change, %XDP_REDIRECT from a Page Pool based driver to ice
becomes zero-alloc as it should be and horrendous 3.3 Mpps / queue
turn into 6.6, hehe.

Let it go with no "Fixes:" tag as it spans across good 5+ commits and
can't be trivially backported.

Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20230210170618.1973430-6-alexandr.lobakin@intel.com

ice: Robustify cleaning/completing XDP Tx buffers

When queueing frames from a Page Pool for redirecting to a device backed
by the ice driver, `perf top` shows heavy load on page_alloc() and
page_frag_free(), despite that on a properly working system it must be
fully or at least almost zero-alloc. The problem is in fact a bit deeper
and raises from how ice cleans up completed Tx buffers.

The story so far: when cleaning/freeing the resources related to
a particular completed Tx frame (skbs, DMA mappings etc.), ice uses some
heuristics only without setting any type explicitly (except for dummy
Flow Director packets, which are marked via ice_tx_buf::tx_flags).
This kinda works, but only up to some point. For example, currently ice
assumes that each frame coming to __ice_xmit_xdp_ring(), is backed by
either plain order-0 page or plain page frag, while it may also be
backed by Page Pool or any other possible memory models introduced in
future. This means any &xdp_frame must be freed properly via
xdp_return_frame() family with no assumptions.

In order to do that, the whole heuristics must be replaced with setting
the Tx buffer/frame type explicitly, just how it's always been done via
an enum. Let us reuse 16 bits from ::tx_flags -- 1 bit-and instr won't
hurt much -- especially given that sometimes there was a check for
%ICE_TX_FLAGS_DUMMY_PKT, which is now turned from a flag to an enum
member. The rest of the changes is straightforward and most of it is
just a conversion to rely now on the type set in &ice_tx_buf rather than
to some secondary properties.
For now, no functional changes intended, the change only prepares the
ground for starting freeing XDP frames properly next step. And it must
be done atomically/synchronously to not break stuff.

Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20230210170618.1973430-5-alexandr.lobakin@intel.com

ice: Remove two impossible branches on XDP Tx cleaning

The tagged commit started sending %XDP_TX frames from XSk Rx ring
directly without converting it to an &xdp_frame. However, when XSk is
enabled on a queue pair, it has its separate Tx cleaning functions, so
neither ice_clean_xdp_irq() nor ice_unmap_and_free_tx_buf() ever happens
there.
Remove impossible branches in order to reduce the diffstat of the
upcoming change.

Fixes: a24b4c6e9aab ("ice: xsk: Do not convert to buff to frame for XDP_TX")
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20230210170618.1973430-4-alexandr.lobakin@intel.com

ice: xsk: Do not convert to buff to frame for XDP_TX

Let us store pointer to xdp_buff that came from xsk_buff_pool on tx_buf
so that it will be possible to recycle it via xsk_buff_free() on Tx
cleaning side. This way it is not necessary to do expensive copy to
another xdp_buff backed by a newly allocated page.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-14-maciej.fijalkowski@intel.com

ice: Remove next_{dd,rs} fields from ice_tx_ring

Now that both ZC and standard XDP data paths stopped using Tx logic
based on next_dd and next_rs fields, we can safely remove these fields
and shrink Tx ring structure.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-13-maciej.fijalkowski@intel.com

ice: Add support for XDP multi-buffer on Tx side

Similarly as for Rx side in previous patch, logic on XDP Tx in ice
driver needs to be adjusted for multi-buffer support. Specifically, the
way how HW Tx descriptors are produced and cleaned.

Currently, XDP_TX works on strict ring boundaries, meaning it sets RS
bit (on producer side) / looks up DD bit (on consumer/cleaning side)
every quarter of the ring. It means that if for example multi buffer
frame would span across the ring quarter boundary (say that frame
consists of 4 frames and we start from 62 descriptor where ring is sized
to 256 entries), RS bit would be produced in the middle of multi buffer
frame, which would be a broken behavior as it needs to be set on the
last descriptor of the frame.

To make it work, set RS bit at the last descriptor from the batch of
frames that XDP_TX action was used on and make the first entry remember
the index of last descriptor with RS bit set. This way, cleaning side
can take the index of descriptor with RS bit, look up DD bit's presence
and clean from first entry to last.

In order to clean up the code base introduce the common ice_set_rs_bit()
which will return index of descriptor that got RS bit produced on so
that standard driver can store this within proper ice_tx_buf and ZC
driver can simply ignore return value.

Co-developed-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-12-maciej.fijalkowski@intel.com

ice: Add support for XDP multi-buffer on Rx side

Ice driver needs to be a bit reworked on Rx data path in order to
support multi-buffer XDP. For skb path, it currently works in a way that
Rx ring carries pointer to skb so if driver didn't manage to combine
fragmented frame at current NAPI instance, it can restore the state on
next instance and keep looking for last fragment (so descriptor with EOP
bit set). What needs to be achieved is that xdp_buff needs to be
combined in such way (linear + frags part) in the first place. Then skb
will be ready to go in case of XDP_PASS or BPF program being not present
on interface. If BPF program is there, it would work on multi-buffer
XDP. At this point xdp_buff resides directly on Rx ring, so given the
fact that skb will be built straight from xdp_buff, there will be no
further need to carry skb on Rx ring.

Besides removing skb pointer from Rx ring, lots of members have been
moved around within ice_rx_ring. First and foremost reason was to place
rx_buf with xdp_buff on the same cacheline. This means that once we
touch rx_buf (which is a preceding step before touching xdp_buff),
xdp_buff will already be hot in cache. Second thing was that xdp_rxq is
used rather rarely and it occupies a separate cacheline, so maybe it is
better to have it at the end of ice_rx_ring.

Other change that affects ice_rx_ring is the introduction of
ice_rx_ring::first_desc. Its purpose is twofold - first is to propagate
rx_buf->act to all the parts of current xdp_buff after running XDP
program, so that ice_put_rx_buf() that got moved out of the main Rx
processing loop will be able to tak an appriopriate action on each
buffer. Second is for ice_construct_skb().

ice_construct_skb() has a copybreak mechanism which had an explicit
impact on xdp_buff->skb conversion in the new approach when legacy Rx
flag is toggled. It works in a way that linear part is 256 bytes long,
if frame is bigger than that, remaining bytes are going as a frag to
skb_shared_info.

This means while memcpying frags from xdp_buff to newly allocated skb,
care needs to be taken when picking the destination frag array entry.
Upon the time ice_construct_skb() is called, when dealing with
fragmented frame, current rx_buf points to the *last* fragment, but
copybreak needs to be done against the first one. That's where
ice_rx_ring::first_desc helps.

When frame building spans across NAPI polls (DD bit is not set on
current descriptor and xdp->data is not NULL) with current Rx buffer
handling state there might be some problems.
Since calls to ice_put_rx_buf() were pulled out of the main Rx
processing loop and were scoped from cached_ntc to current ntc, remember
that now mentioned function relies on rx_buf->act, which is set within
ice_run_xdp(). ice_run_xdp() is called when EOP bit was found, so
currently we could put Rx buffer with rx_buf->act being *uninitialized*.
To address this, change scoping to rely on first_desc on both boundaries
instead.

This also implies that cleaned_count which is used as an input to
ice_alloc_rx_buffers() and tells how many new buffers should be refilled
has to be adjusted. If it stayed as is, what could happen is a case
where ntc would go over ntu.

Therefore, remove cleaned_count altogether and use against allocing
routine newly introduced ICE_RX_DESC_UNUSED() macro which is an
equivalent of ICE_DESC_UNUSED() dedicated for Rx side and based on
struct ice_rx_ring::first_desc instead of next_to_clean.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-11-maciej.fijalkowski@intel.com

ice: Use xdp->frame_sz instead of recalculating truesize

SKB path calculates truesize on three different functions, which could
be avoided as xdp_buff carries the already calculated truesize under
xdp_buff::frame_sz. If ice_add_rx_frag() is adjusted to take the
xdp_buff as an input just like functions responsible for creating
sk_buff initially, codebase could be simplified by removing these
redundant recalculations and rely on xdp_buff::frame_sz instead.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-10-maciej.fijalkowski@intel.com

ice: Do not call ice_finalize_xdp_rx() unnecessarily

Currently ice_finalize_xdp_rx() is called only when xdp_prog is present
on VSI, which is a good thing. However, this optimization can be
enhanced and check only if any of the XDP_TX/XDP_REDIRECT took place in
current Rx processing. Non-zero value of @xdp_xmit indicates that
xdp_prog is present on VSI. This way XDP_DROP-based workloads will not
suffer from unnecessary calls to external function.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-9-maciej.fijalkowski@intel.com

ice: Centrallize Rx buffer recycling

Currently calls to ice_put_rx_buf() are sprinkled through
ice_clean_rx_irq() - first place is for explicit flow director's
descriptor handling, second is after running XDP prog and the last one
is after taking care of skb.

1st callsite was actually only for ntc bump purpose, as Rx buffer to be
recycled is not even passed to a function.

It is possible to walk through Rx buffers processed in particular NAPI
cycle by caching ntc from beginning of the ice_clean_rx_irq().

To do so, let us store XDP verdict inside ice_rx_buf, so action we need
to take on will be known. For XDP prog absence, just store ICE_XDP_PASS
as a verdict.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-7-maciej.fijalkowski@intel.com

ice: Inline eop check

This might be in future used by ZC driver and might potentially yield a
minor performance boost. While at it, constify arguments that
ice_is_non_eop() takes, since they are pointers and this will help compiler
while generating asm.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-6-maciej.fijalkowski@intel.com

ice: Pull out next_to_clean bump out of ice_put_rx_buf()

Plan is to move ice_put_rx_buf() to the end of ice_clean_rx_irq() so
in order to keep the ability of walking through HW Rx descriptors, pull
out next_to_clean handling out of ice_put_rx_buf().

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-5-maciej.fijalkowski@intel.com

ice: Store page count inside ice_rx_buf

This will allow us to avoid carrying additional auxiliary array of page
counts when dealing with XDP multi buffer support. Previously combining
fragmented frame to skb was not affected in the same way as XDP would be
as whole frame is needed to be in place before executing XDP prog.
Therefore, when going through HW Rx descriptors one-by-one, calls to
ice_put_rx_buf() need to be taken *after* running XDP prog on a
potentially multi buffered frame, so some additional storage of
page count is needed.

By adding page count to rx buf, it will make it easier to walk through
processed entries at the end of rx cleaning routine and decide whether
or not buffers should be recycled.

While at it, bump ice_rx_buf::pagecnt_bias from u16 up to u32. It was
proven many times that calculations on variables smaller than standard
register size are harmful. This was also the case during experiments
with embedding page count to ice_rx_buf - when this was added as u16 it
had a performance impact.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-4-maciej.fijalkowski@intel.com

ice: Add xdp_buff to ice_rx_ring struct

In preparation for XDP multi-buffer support, let's store xdp_buff on
Rx ring struct. This will allow us to combine fragmented frames across
separate NAPI cycles in the same way as currently skb fragments are
handled. This means that skb pointer on Rx ring will become redundant
and will be removed. For now it is kept and layout of Rx ring struct was
not inspected, some member movement will be needed later on so that will
be the time to take care of it.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-3-maciej.fijalkowski@intel.com

ice: Prepare legacy-rx for upcoming XDP multi-buffer support

Rx path is going to be modified in a way that fragmented frame will be
gathered within xdp_buff in the first place. This approach implies that
underlying buffer has to provide tailroom for skb_shared_info. This is
currently the case when ring uses build_skb but not when legacy-rx knob
is turned on. This case configures 2k Rx buffers and has no way to
provide either headroom or tailroom - FWIW it currently has
XDP_PACKET_HEADROOM which is broken and in here it is removed. 2k Rx
buffers were used so driver in this setting was able to support 9k MTU
as it can chain up to 5 Rx buffers. With offset configuring HW writing
2k of a data was passing the half of the page which broke the assumption
of our internal page recycling tricks.

Now if above got fixed and legacy-rx path would be left as is, when
referring to skb_shared_info via xdp_get_shared_info_from_buff(),
packet's content would be corrupted again. Hence size of Rx buffer needs
to be lowered and therefore supported MTU. This operation will allow us
to keep the unified data path and with 8k MTU users (if any of
legacy-rx) would still be good to go. However, tendency is to drop the
support for this code path at some point.

Add ICE_RXBUF_1664 as vsi::rx_buf_len and ICE_MAX_FRAME_LEGACY_RX (8320)
as vsi::max_frame for legacy-rx. For bigger page sizes configure 3k Rx
buffers, not 2k.

Since headroom support is removed, disable data_meta support on legacy-rx.
When preparing XDP buff, rely on ice_rx_ring::rx_offset setting when
deciding whether to support data_meta or not.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-2-maciej.fijalkowski@intel.com

ice: Remove cppcheck suppressions

The use of suppressions for cppcheck in the kernel does not look to be
standard as the ice driver is the only one doing it. Remove the
comments/suppressions.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Accumulate ring statistics over reset

Resets may occur with or without user interaction. For example, a TX hang
or reconfiguration of parameters will result in a reset. During reset, the
VSI is freed, freeing any statistics structures inside as well. This would
create an issue for the user where a reset happens in the background,
statistics set to zero, and the user checks ring statistics expecting them
to be populated.

To ensure this doesn't happen, accumulate ring statistics over reset.

Define a new ring statistics structure, ice_ring_stats. The new structure
lives in the VSI's parent, preserving ring statistics when VSI is freed.

1. Define a new structure vsi_ring_stats in the PF scope
2. Allocate/free stats only during probe, unload, or change in ring size
3. Replace previous ring statistics functionality with new structure

Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: track Tx timestamp stats similar to other Intel drivers

Several Intel networking drivers which support PTP track when Tx timestamps
are skipped or when they timeout without a timestamp from hardware. The
conditions which could cause these events are rare, but it can be useful to
know when and how often they occur.

Implement similar statistics for the ice driver, tx_hwtstamp_skipped,
tx_hwtstamp_timeouts, and tx_hwtstamp_flushed.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: xsk: change batched Tx descriptor cleaning

AF_XDP Tx descriptor cleaning in ice driver currently works in a "lazy"
way - descriptors are not cleaned immediately after send. We rather hold
on with cleaning until we see that free space in ring drops below
particular threshold. This was supposed to reduce the amount of
unnecessary work related to cleaning and instead of keeping the ring
empty, ring was rather saturated.

In AF_XDP realm cleaning Tx descriptors implies producing them to CQ.
This is a way of letting know user space that particular descriptor has
been sent, as John points out in [0].

We tried to implement serial descriptor cleaning which would be used in
conjunction with batched cleaning but it made code base more convoluted
and probably harder to maintain in future. Therefore we step away from
batched cleaning in a current form in favor of an approach where we set
RS bit on every last descriptor from a batch and clean always at the
beginning of ice_xmit_zc().

This means that we give up a bit of Tx performance, but this doesn't
hurt l2fwd scenario which is way more meaningful than txonly as this can
be treaten as AF_XDP based packet generator. l2fwd is not hurt due to
the fact that Tx side is much faster than Rx and Rx is the one that has
to catch Tx up.

FWIW Tx descriptors are still produced in a batched way.

[0]: https://lore.kernel.org/bpf/62b0a20232920_3573208ab@john.notmuch/

Fixes: 126cdfe1007a ("ice: xsk: Improve AF_XDP ZC Tx and use batching API")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Fix ice_xdp_xmit() when XDP TX queue number is not sufficient

The original patch added the static branch to handle the situation,
when assigning an XDP TX queue to every CPU is not possible,
so they have to be shared.

However, in the XDP transmit handler ice_xdp_xmit(), an error was
returned in such cases even before static condition was checked,
thus making queue sharing still impossible.

Fixes: 22bf877e528f ("ice: introduce XDP_TX fallback path")
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/r/20220919134346.25030-1-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ice: Fix tunnel checksum offload with fragmented traffic

Fix checksum offload on VXLAN tunnels.
In case, when mpls protocol is not used, set l4 header to transport
header of skb. This fixes case, when user tries to offload checksums
of VXLAN tunneled traffic.

Steps for reproduction (requires link partner with tunnels):
ip l s enp130s0f0 up
ip a f enp130s0f0
ip a a 10.10.110.2/24 dev enp130s0f0
ip l s enp130s0f0 mtu 1600
ip link add vxlan12_sut type vxlan id 12 group 238.168.100.100 dev enp130s0f0 dstport 4789
ip l s vxlan12_sut up
ip a a 20.10.110.2/24 dev vxlan12_sut
iperf3 -c 20.10.110.1 #should connect

Offload params: td_offset, cd_tunnel_params were
corrupted, due to l4 header pointing wrong address. NIC would then drop
those packets internally, due to incorrect TX descriptor data,
which increased GLV_TEPC register.

Fixes: 69e66c04c672 ("ice: Add mpls+tso support")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Add mpls+tso support

Attempt to add mpls+tso support.

I don't have ice hardware available to test myself, but I just implemented
this feature in i40e and thought it might be useful to implement for ice
while this is fresh in my brain.

Hoping some one at intel will be able to test this on my behalf.

Signed-off-by: Joe Damato <jdamato@fastly.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: avoid XDP checks in ice_clean_tx_irq()

Commit 9610bd988df9 ("ice: optimize XDP_TX workloads") introduced Tx IRQ
cleaning routine dedicated for XDP rings. Currently it is impossible to
call ice_clean_tx_irq() against XDP ring, so it is safe to drop
ice_ring_is_xdp() calls in there.

Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: store VF pointer instead of VF ID

The VSI structure contains a vf_id field used to associate a VSI with a
VF. This is used mainly for ICE_VSI_VF as well as partially for
ICE_VSI_CTRL associated with the VFs.

This API was designed with the idea that VFs are stored in a simple
array that was expected to be static throughout most of the driver's
life.

We plan on refactoring VF storage in a few key ways:

1) converting from a simple static array to a hash table
2) using krefs to track VF references obtained from the hash table
3) use RCU to delay release of VF memory until after all references
are dropped

This is motivated by the goal to ensure that the lifetime of VF
structures is accounted for, and prevent various use-after-free bugs.

With the existing vsi->vf_id, the reference tracking for VFs would
become somewhat convoluted, because each VSI maintains a vf_id field
which will then require performing a look up. This means all these flows
will require reference tracking and proper usage of rcu_read_lock, etc.

We know that the VF VSI will always be backed by a valid VF structure,
because the VSI is created during VF initialization and removed before
the VF is destroyed. Rely on this and store a reference to the VF in the
VSI structure instead of storing a VF ID. This will simplify the usage
and avoid the need to perform lookups on the hash table in the future.

For ICE_VSI_VF, it is expected that vsi->vf is always non-NULL after
ice_vsi_alloc succeeds. Because of this, use WARN_ON when checking if a
vsi->vf pointer is valid when dealing with VF VSIs. This will aid in
debugging code which violates this assumption and avoid more disastrous
panics.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Add hot path support for 802.1Q and 802.1ad VLAN offloads

Currently the driver only supports 802.1Q VLAN insertion and stripping.
However, once Double VLAN Mode (DVM) is fully supported, then both 802.1Q
and 802.1ad VLAN insertion and stripping will be supported. Unfortunately
the VSI context parameters only allow for one VLAN ethertype at a time
for VLAN offloads so only one or the other VLAN ethertype offload can be
supported at once.

To support this, multiple changes are needed.

Rx path changes:

[1] In DVM, the Rx queue context l2tagsel field needs to be cleared so
the outermost tag shows up in the l2tag2_2nd field of the Rx flex
descriptor. In Single VLAN Mode (SVM), the l2tagsel field should remain
1 to support SVM configurations.

[2] Modify the ice_test_staterr() function to take a __le16 instead of
the ice_32b_rx_flex_desc union pointer so this function can be used for
both rx_desc->wb.status_error0 and rx_desc->wb.status_error1.

[3] Add the new inline function ice_get_vlan_tag_from_rx_desc() that
checks if there is a VLAN tag in l2tag1 or l2tag2_2nd.

[4] In ice_receive_skb(), add a check to see if NETIF_F_HW_VLAN_STAG_RX
is enabled in netdev->features. If it is, then this is the VLAN
ethertype that needs to be added to the stripping VLAN tag. Since
ice_fix_features() prevents CTAG_RX and STAG_RX from being enabled
simultaneously, the VLAN ethertype will only ever be 802.1Q or 802.1ad.

Tx path changes:

[1] In DVM, the VLAN tag needs to be placed in the l2tag2 field of the Tx
context descriptor. The new define ICE_TX_FLAGS_HW_OUTER_SINGLE_VLAN was
added to the list of tx_flags to handle this case.

[2] When the stack requests the VLAN tag to be offloaded on Tx, the
driver needs to set either ICE_TX_FLAGS_HW_OUTER_SINGLE_VLAN or
ICE_TX_FLAGS_HW_VLAN, so the tag is inserted in l2tag2 or l2tag1
respectively. To determine which location to use, set a bit in the Tx
ring flags field during ring allocation that can be used to determine
which field to use in the Tx descriptor. In DVM, always use l2tag2,
and in SVM, always use l2tag1.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: respect metadata in legacy-rx/ice_construct_skb()

In "legacy-rx" mode represented by ice_construct_skb(), we can
still use XDP (and XDP metadata), but after XDP_PASS the metadata
will be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
Point net_prefetch() to xdp->data_meta instead of data. This won't
change anything when the meta is not here, but will save some cache
misses otherwise.

Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: xsk: Improve AF_XDP ZC Tx and use batching API

Apply the logic that was done for regular XDP from commit 9610bd988df9
("ice: optimize XDP_TX workloads") to the ZC side of the driver. On top
of that, introduce batching to Tx that is inspired by i40e's
implementation with adjustments to the cleaning logic - take into the
account NAPI budget in ice_clean_xdp_irq_zc().

Separating the stats structs onto separate cache lines seemed to improve
the performance.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20220125160446.78976-8-maciej.fijalkowski@intel.com

ice: xsk: Avoid potential dead AF_XDP Tx processing

Commit 9610bd988df9 ("ice: optimize XDP_TX workloads") introduced
@next_dd and @next_rs to ice_tx_ring struct. Currently, their state is
not restored in ice_clean_tx_ring(), which was not causing any troubles
as the XDP rings are gone after we're done with XDP prog on interface.

For upcoming usage of mentioned fields in AF_XDP, this might expose us
to a potential dead Tx side. Scenario would look like following (based
on xdpsock):

- two xdpsock instances are spawned in Tx mode
- one of them is killed
- XDP prog is kept on interface due to the other xdpsock still running
* this means that XDP rings stayed in place
- xdpsock is launched again on same queue id that was terminated on
- @next_dd and @next_rs setting is bogus, therefore transmit side is
broken

To protect us from the above, restore the initial @next_rs and @next_dd
values when cleaning the Tx ring.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20220125160446.78976-7-maciej.fijalkowski@intel.com

ice: Remove likely for napi_complete_done

Remove the likely before napi_complete_done as this is the unlikely case
when busy-poll is used. Removing this has a positive performance impact
for busy-poll and no negative impact to the regular case.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20220125160446.78976-2-maciej.fijalkowski@intel.com

ice: switch to napi_build_skb()

napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
ice driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.

Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: use modern kernel API for kick

The kernel gained a new interface for drivers to use to combine tail
bump (doorbell) and BQL updates, attempt to use those new interfaces.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: use prefetch methods

The kernel provides some prefetch mechanisms to speed up commonly
cold cache line accesses during receive processing. Since these are
software structures it helps to have these strategically placed
prefetches.

Be careful to call BQL prefetch complete only for non XDP queues.

Co-developed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: update to newer kernel API

Use the netif_tx_* API from netdevice.h which has simpler parameters.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

bpf: Let bpf_warn_invalid_xdp_action() report more info

In non trivial scenarios, the action id alone is not sufficient to
identify the program causing the warning. Before the previous patch,
the generated stack-trace pointed out at least the involved device
driver.

Let's additionally include the program name and id, and the relevant
device name.

If the user needs additional infos, he can fetch them via a kernel
probe, leveraging the arguments added here.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com

ice: xsk: allocate separate memory for XDP SW ring

Currently, the zero-copy data path is reusing the memory region that was
initially allocated for an array of struct ice_rx_buf for its own
purposes. This is error prone as it is based on the ice_rx_buf struct
always being the same size or bigger than what the zero-copy path needs.
There can also be old values present in that array giving rise to errors
when the zero-copy path uses it.

Fix this by freeing the ice_rx_buf region and allocating a new array for
the zero-copy path that has the right length and is initialized to zero.

Fixes: 57f7f8b6bc0b ("ice: Use xdp_buf instead of rx_buf for xsk zero-copy")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: use devm_kcalloc() instead of devm_kzalloc()

Use 2-factor multiplication argument form devm_kcalloc() instead
of devm_kzalloc().

Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: fix software generating extra interrupts

The driver tried to work around missing completion events that occurred
while interrupts are disabled, by triggering a software interrupt
whenever we exit polling (but we had to have polled at least once).

This was causing a *lot* of extra interrupts for some workloads like
NVMe over TCP, which resulted in regressions in performance. It was also
visible when polling didn't prevent interrupts when busy_poll was
enabled.

Fix the extra interrupts by utilizing our previously unused 3rd ITR
(interrupt throttle) index and set it to 20K interrupts per second, and
then trigger a software interrupt within that rate limit.

While here, slightly refactor the code to avoid an overwrite of a local
variable in the case of wb_en = true.

Fixes: b7306b42beaf ("ice: manage interrupts during poll exit")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: update dim usage and moderation

The driver was having trouble with unreliable latency when doing single
threaded ping-pong tests. This was root caused to the DIM algorithm
landing on a too slow interrupt value, which caused high latency, and it
was especially present when queues were being switched frequently by the
scheduler as happens on default setups today.

In attempting to improve this, we allow the upper rate limit for
interrupts to move to rate limit of 4 microseconds as a max, which means
that no vector can generate more than 250,000 interrupts per second. The
old config was up to 100,000. The driver previously tried to program the
rate limit too frequently and if the receive and transmit side were both
active on the same vector, the INTRL would be set incorrectly, and this
change fixes that issue as a side effect of the redesign.

This driver will operate from now on with a slightly changed DIM table
with more emphasis towards latency sensitivity by having more table
entries with lower latency than with high latency (high being >= 64
microseconds).

The driver also resets the DIM algorithm state with a new stats set when
there is no work done and the data becomes stale (older than 1 second),
for the respective receive or transmit portion of the interrupt.

Add a new helper for setting rate limit, which will be used more
in a followup patch.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: introduce XDP_TX fallback path

Under rare circumstances there might be a situation where a requirement
of having XDP Tx queue per CPU could not be fulfilled and some of the Tx
resources have to be shared between CPUs. This yields a need for placing
accesses to xdp_ring inside a critical section protected by spinlock.
These accesses happen to be in the hot path, so let's introduce the
static branch that will be triggered from the control plane when driver
could not provide Tx queue dedicated for XDP on each CPU.

Currently, the design that has been picked is to allow any number of XDP
Tx queues that is at least half of a count of CPUs that platform has.
For lower number driver will bail out with a response to user that there
were not enough Tx resources that would allow configuring XDP. The
sharing of rings is signalled via static branch enablement which in turn
indicates that lock for xdp_ring accesses needs to be taken in hot path.

Approach based on static branch has no impact on performance of a
non-fallback path. One thing that is needed to be mentioned is a fact
that the static branch will act as a global driver switch, meaning that
if one PF got out of Tx resources, then other PFs that ice driver is
servicing will suffer. However, given the fact that HW that ice driver
is handling has 1024 Tx queues per each PF, this is currently an
unlikely scenario.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: optimize XDP_TX workloads

Optimize Tx descriptor cleaning for XDP. Current approach doesn't
really scale and chokes when multiple flows are handled.

Introduce two ring fields, @next_dd and @next_rs that will keep track of
descriptor that should be looked at when the need for cleaning arise and
the descriptor that should have the RS bit set, respectively.

Note that at this point the threshold is a constant (32), but it is
something that we could make configurable.

First thing is to get away from setting RS bit on each descriptor. Let's
do this only once NTU is higher than the currently @next_rs value. In
such case, grab the tx_desc[next_rs], set the RS bit in descriptor and
advance the @next_rs by a 32.

Second thing is to clean the Tx ring only when there are less than 32
free entries. For that case, look up the tx_desc[next_dd] for a DD bit.
This bit is written back by HW to let the driver know that xmit was
successful. It will happen only for those descriptors that had RS bit
set. Clean only 32 descriptors and advance the DD bit.

Actual cleaning routine is moved from ice_napi_poll() down to the
ice_xmit_xdp_ring(). It is safe to do so as XDP ring will not get any
SKBs in there that would rely on interrupts for the cleaning. Nice side
effect is that for rare case of Tx fallback path (that next patch is
going to introduce) we don't have to trigger the SW irq to clean the
ring.

With those two concepts, ring is kept at being almost full, but it is
guaranteed that driver will be able to produce Tx descriptors.

This approach seems to work out well even though the Tx descriptors are
produced in one-by-one manner. Test was conducted with the ice HW
bombarded with packets from HW generator, configured to generate 30
flows.

Xdp2 sample yields the following results:
<snip>
proto 17: 79973066 pkt/s
proto 17: 80018911 pkt/s
proto 17: 80004654 pkt/s
proto 17: 79992395 pkt/s
proto 17: 79975162 pkt/s
proto 17: 79955054 pkt/s
proto 17: 79869168 pkt/s
proto 17: 79823947 pkt/s
proto 17: 79636971 pkt/s
</snip>

As that sample reports the Rx'ed frames, let's look at sar output.
It says that what we Rx'ed we do actually Tx, no noticeable drops.
Average: IFACE rxpck/s txpck/s rxkB/s txkB/s rxcmp/s txcmp/s rxmcst/s %ifutil
Average: ens4f1 79842324.00 79842310.40 4678261.17 4678260.38 0.00 0.00 0.00 38.32

with tx_busy staying calm.

When compared to a state before:
Average: IFACE rxpck/s txpck/s rxkB/s txkB/s rxcmp/s txcmp/s rxmcst/s %ifutil
Average: ens4f1 90919711.60 42233822.60 5327326.85 2474638.04 0.00 0.00 0.00 43.64

it can be observed that the amount of txpck/s is almost doubled, meaning
that the performance is improved by around 90%. All of this due to the
drops in the driver, previously the tx_busy stat was bumped at a 7mpps
rate.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: propagate xdp_ring onto rx_ring

With rings being split, it is now convenient to introduce a pointer to
XDP ring within the Rx ring. For XDP_TX workloads this means that
xdp_rings array access will be skipped, which was executed per each
processed frame.

Also, read the XDP prog once per NAPI and if prog is present, set up the
local xdp_ring pointer. Reading prog a single time was discussed in [1]
with some concern raised by Toke around dispatcher handling and having
the need for going through the RCU grace period in the ndo_bpf driver
callback, but ice currently is torning down NAPI instances regardless of
the prog presence on VSI.

Although the pointer to XDP ring introduced to Rx ring makes things a
lot slimmer/simpler, I still feel that single prog read per NAPI
lifetime is beneficial.

Further patch that will introduce the fallback path will also get a
profit from that as xdp_ring pointer will be set during the XDP rings
setup.

[1]: https://lore.kernel.org/bpf/87k0oseo6e.fsf@toke.dk/

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: do not create xdp_frame on XDP_TX

xdp_frame is not needed for XDP_TX data path in ice driver case.
For this data path cleaning of sent descriptor will not happen anywhere
outside of the driver, which means that carrying the information about
the underlying memory model via xdp_frame will not be used. Therefore,
this conversion can be simply dropped, which would relieve CPU a bit.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: split ice_ring onto Tx/Rx separate structs

While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.

Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.

Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.

Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.

Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.

Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: switchdev slow path

Slow path means allowing packet to go from uplink to representor
and from representor to correct VF on Rx site and from VF to
representor and to uplink on Tx site.

To accomplish this driver, has to set correct Tx descriptor. When
packet is sent from representor to VF, destination should be
set to VF VSI. When packet is sent from uplink port destination
should be uplink to bypass switch infrastructure and send packet
outside.

On Rx site driver should check source VSI field from Rx descriptor
and based on that forward packed to correct netdev. To allow
this there is a target netdevs table in control plane VSI
struct.

Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Add DSCP support

Implement code to handle submission of APP TLV's
containing DSCP to TC mapping.

The first such mapping received on an interface
will cause that PF to switch to L3 DSCP QoS mode,
apply the default config for that mode, and apply
the received mapping.

Only one such mapping will be allowed per DSCP value,
and when the last DSCP mapping is deleted, the PF
will switch back into L2 VLAN QoS mode, applying the
appropriate default QoS settings.

L3 DSCP QoS mode will only be allowed in SW DCBx
mode, in other words, when the FW LLDP engine is
disabled. Commands that break this mutual exclusivity
will be blocked.

Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: add tracepoints

This patch is modeled after one by Scott Peterson for i40e.

Add tracepoints to the driver, via a new file ice_trace.h and some new
trace calls added in interesting places in the driver. Add some tracing
for DIMLIB to help debug interrupt moderation problems.

Performance should not be affected, and this can be very useful
for debugging and adding new trace events to paths in the future.

Note eBPF programs can attach to these events, as well as perf
can count them since we're attaching to the events subsystem
in the kernel.

Co-developed-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

intel: Remove rcu_read_lock() around XDP program invocation

The Intel drivers all have rcu_read_lock()/rcu_read_unlock() pairs around
XDP program invocations. However, the actual lifetime of the objects
referred by the XDP program invocation is longer, all the way through to
the call to xdp_do_flush(), making the scope of the rcu_read_lock() too
small. This turns out to be harmless because it all happens in a single
NAPI poll cycle (and thus under local_bh_disable()), but it makes the
rcu_read_lock() misleading.

Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.

Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com> # i40e
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/bpf/20210624160609.292325-12-toke@redhat.com

ice: report hash type such as L2/L3/L4

The hardware is reporting the type of the hash used for RSS
as a PTYPE field in the receive descriptor. Use this value to set
the skb packet hash type by extending the hash type table to
cover all 10-bits of possible values (requiring some variables
to be changed from u8 to u16), and then use that table to convert
to one of the possible values in enum pkt_hash_types.

While we're here, remove the unused ptype struct value, which
makes table init easier for the zero entries, and use ranged
initializer to remove a bunch of code (works with gcc and clang).

Without this change, the kernel will recalculate the hash in software,
which can consume extra CPU cycles.

Co-developed-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: enable transmit timestamps for E810 devices

Add support for enabling Tx timestamp requests for outgoing packets on
E810 devices.

The ice hardware can support multiple outstanding Tx timestamp requests.
When sending a descriptor to hardware, a Tx timestamp request is made by
setting a request bit, and assigning an index that represents which Tx
timestamp index to store the timestamp in.

Hardware makes no effort to synchronize the index use, so it is up to
software to ensure that Tx timestamp indexes are not re-used before the
timestamp is reported back.

To do this, introduce a Tx timestamp tracker which will keep track of
currently in-use indexes.

In the hot path, if a packet has a timestamp request, an index will be
requested from the tracker. Unfortunately, this does require a lock as
the indexes are shared across all queues on a PHY. There are not enough
indexes to reliably assign only 1 to each queue.

For the E810 devices, the timestamp indexes are not shared across PHYs,
so each port can have its own tracking.

Once hardware captures a timestamp, an interrupt is fired. In this
interrupt, trigger a new work item that will figure out which timestamp
was completed, and report the timestamp back to the stack.

This function loops through the Tx timestamp indexes and checks whether
there is now a valid timestamp. If so, it clears the PHY timestamp
indication in the PHY memory, locks and removes the SKB and bit in the
tracker, then reports the timestamp to the stack.

It is possible in some cases that a timestamp request will be initiated
but never completed. This might occur if the packet is dropped by
software or hardware before it reaches the PHY.

Add a task to the periodic work function that will check whether
a timestamp request is more than a few seconds old. If so, the timestamp
index is cleared in the PHY, and the SKB is released.

Just as with Rx timestamps, the Tx timestamps are only 40 bits wide, and
use the same overall logic for extending to 64 bits of nanoseconds.

With this change, E810 devices should be able to perform basic PTP
functionality.

Future changes will extend the support to cover the E822-based devices.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Allow all LLDP packets from PF to Tx

Currently in the ice driver, the check whether to
allow a LLDP packet to egress the interface from the
PF_VSI is being based on the SKB's priority field.
It checks to see if the packets priority is equal to
TC_PRIO_CONTROL. Injected LLDP packets do not always
meet this condition.

SCAPY defaults to a sk_buff->protocol value of ETH_P_ALL
(0x0003) and does not set the priority field. There will
be other injection methods (even ones used by end users)
that will not correctly configure the socket so that
SKB fields are correctly populated.

Then ethernet header has to have to correct value for
the protocol though.

Add a check to also allow packets whose ethhdr->h_proto
matches ETH_P_LLDP (0x88CC).

Fixes: 0c3a6101ff2d ("ice: Allow egress control packets from PF_VSI")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: add correct exception tracing for XDP

Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.

Fixes: efc2214b6047 ("ice: Add support for XDP")
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: refactor ITR data structures

Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.

Basically unpack the "high bit means dynamic" logic
into bitfields.

Also, remove some unused ITR defines.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: manage interrupts during poll exit

The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the introduction of the ice driver.

Attempt to "catch" any remaining work by triggering a software
interrupt when exiting napi poll or busy-poll. This will not
cause extra interrupts in the case of normal execution.

This issue was found when running sfnt-pingpong, with busy
poll enabled, and typically with larger I/O sizes like > 8192,
the program would occasionally report > 1 second maximums
to complete a ping pong.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: replace custom AIM algorithm with kernel's DIM library

The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.

The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.

The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.

The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).

There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.

The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.

Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Consolidate VSI state and flags

struct ice_vsi has two fields, state and flags which seem to
be serving the same purpose. Consolidate them into one field
'state'.

enum ice_state is used to represent state information of the PF.
While some of these enum values can be use to represent VSI state,
it makes more sense to represent VSI state with its own enum. So
derive a new enum ice_vsi_state from ice_vsi_flags and ice_state
and use it. Also rename enum ice_state to ice_pf_state for clarity.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Check FDIR program status for AVF

Enable returning FDIR completion status by checking the
ctrl_vsi Rx queue descriptor value.

To enable returning FDIR completion status from ctrl_vsi Rx queue,
COMP_Queue and COMP_Report of FDIR filter programming descriptor
needs to be properly configured. After program request sent to ctrl_vsi
Tx queue, ctrl_vsi Rx queue interrupt will be triggered and
completion status will be returned.

Driver will first issue request in ice_vc_fdir_add_fltr(), then
pass FDIR context to the background task in interrupt service routine
ice_vc_fdir_irq_handler() and finally deal with them in
ice_flush_fdir_ctx(). ice_flush_fdir_ctx() will check the descriptor's
value, fdir context, and then send back virtual channel message to VF
by calling ice_vc_add_fdir_fltr_post(). An additional timer will be
setup in case of hardware interrupt timeout.

Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

bpf, devmap: Move drop error path to devmap for XDP_REDIRECT

We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is working
towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error
path handling from each XDP ethernet driver to devmap code. According to
the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx
loop whenever the hw reports a tx error and it will just return to devmap
caller the number of successfully transmitted frames. It will be devmap
responsibility to free dropped frames.

Move each XDP ndo_xdp_xmit capable driver to the new APIs:

- veth
- virtio-net
- mvneta
- mvpp2
- socionext
- amazon ena
- bnxt
- freescale (dpaa2, dpaa)
- xen-frontend
- qede
- ice
- igb
- ixgbe
- i40e
- mlx5
- ti (cpsw, cpsw-new)
- tun
- sfc

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org

ice: move headroom initialization to ice_setup_rx_ctx

ice_rx_offset(), that is supposed to initialize the Rx buffer headroom,
relies on ICE_RX_FLAGS_RING_BUILD_SKB flag as well as XDP prog presence.

Currently, the callsite of mentioned function is placed incorrectly
within ice_setup_rx_ring() where Rx ring's build skb flag is not
set yet. This causes the XDP_REDIRECT to be partially broken due to
inability to create xdp_frame in the headroom space, as the headroom is
0.

Fix this by moving ice_rx_offset() to ice_setup_rx_ctx() after the flag
setting.

Fixes: f1b1f409bf79 ("ice: store the result of ice_rx_offset() onto ice_ring")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: store the result of ice_rx_offset() onto ice_ring

Output of ice_rx_offset() is based on ethtool's priv flag setting, which
when changed, causes PF reset (disables napi, frees irqs, loads
different Rx mem model, etc.). This means that within napi its result is
constant and there is no reason to call it per each processed frame.

Add new 'rx_offset' field to ice_ring that is meant to hold the
ice_rx_offset() result and use it within ice_clean_rx_irq().
Furthermore, use it within ice_alloc_mapped_page().

Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: move skb pointer from rx_buf to rx_ring

Similar thing has been done in i40e, as there is no real need for having
the sk_buff pointer in each rx_buf. Non-eop frames can be simply handled
on that pointer moved upwards to rx_ring.

Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: simplify ice_run_xdp

There's no need for 'result' variable, we can directly return the
internal status based on action returned by xdp prog.

Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Refactor DCB related variables out of the ice_port_info struct

Refactor the DCB related variables out of the ice_port_info_struct. The
goal is to make the ice_port_info struct cleaner.

Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Co-developed-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: fix writeback enable logic

The writeback enable logic was incorrectly implemented (due to
misunderstanding what the side effects of the implementation would be
during polling).

Fix this logic issue, while implementing a new feature allowing the user
to control the writeback frequency using the knobs for controlling
interrupt throttling that we already have. Basically if you leave
adaptive interrupts enabled, the writeback frequency will be varied even
if busy_polling or if napi-poll is in use. If the interrupt rates are
set to a fixed value by ethtool -C and adaptive is off, the driver will
allow the user-set interrupt rate to guide how frequently the hardware
will complete descriptors to the driver.

Effectively the user will get a control over the hardware efficiency,
allowing the choice between immediate interrupts or delayed up to a
maximum of the interrupt rate, even when interrupts are disabled
during polling.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

net: use the new dev_page_is_reusable() instead of private versions

Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.

Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net, xdp: Introduce xdp_prepare_buff utility routine

Introduce xdp_prepare_buff utility routine to initialize per-descriptor
xdp_buff fields (e.g. xdp_buff pointers). Rely on xdp_prepare_buff() in
all XDP capable drivers.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/bpf/45f46f12295972a97da8ca01990b3e71501e9d89.1608670965.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

net, xdp: Introduce xdp_init_buff utility routine

Introduce xdp_init_buff utility routine to initialize xdp_buff fields
const over NAPI iterations (e.g. frame_sz or rxq pointer). Rely on
xdp_init_buff in all XDP capable drivers.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/bpf/7f8329b6da1434dc2b05a77f2e800b29628a8913.1608670965.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

ice: Implement flow for IPv6 next header (extension header)

This patch is based on a similar change to i40e by Slawomir Laba:
"i40e: Implement flow for IPv6 next header (extension header)".

When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.

The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with ICE_TX_CTX_EIPT_IPV6.
The extension header was not skipped at all.

The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.

Fixes: a4e82a81f573 ("ice: Add support for tunnel offloads")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: avoid premature Rx buffer reuse

The page recycle code, incorrectly, relied on that a page fragment
could not be freed inside xdp_do_redirect(). This assumption leads to
that page fragments that are used by the stack/XDP redirect can be
reused and overwritten.

To avoid this, store the page count prior invoking xdp_do_redirect().

Fixes: efc2214b6047 ("ice: Add support for XDP")
Reported-and-analyzed-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

xsk: Propagate napi_id to XDP socket Rx path

Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.

Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com

xsk: i40e: ice: ixgbe: mlx5: Pass buffer pool to driver instead of umem

Replace the explicit umem reference passed to the driver in AF_XDP
zero-copy mode with the buffer pool instead. This in preparation for
extending the functionality of the zero-copy mode so that umems can be
shared between queues on the same netdev and also between netdevs. In
this commit, only an umem reference has been added to the buffer pool
struct. But later commits will add other entities to it. These are
going to be entities that are different between different queue ids
and netdevs even though the umem is shared between them.

Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-2-git-send-email-magnus.karlsson@intel.com

net: Take common prefetch code structure into a function

Many device drivers use the same prefetch code structure to
deal with small L1 cacheline size.
Take this code into a function and call it from the drivers.

Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ice: Misc minor fixes

This is a collection of minor fixes including typos, white space, and
style. No functional changes.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

ice: port fix for chk_linearlize

This is a port of commit 248de22e638f ("i40e/i40evf: Account for frags
split over multiple descriptors in check linearize")

As part of testing workloads (read/write) using larger IO size (128K)
tx_timeout is observed and whenever it happens, it was due to
tx_linearize.

Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: remove page_reuse statistic

The page reuse statistic wasn't even being displayed to the user, even
though the driver counted it. Don't waste the struct space and hot-path
cycles since the driver doesn't display it.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: fix unused parameter warning

Depending on PAGE_SIZE, the following unused parameter warning can be
reported:

drivers/net/ethernet/intel/ice/ice_txrx.c: In function ‘ice_rx_frame_truesize’:
drivers/net/ethernet/intel/ice/ice_txrx.c:513:21: warning: unused parameter ‘size’ [-Wunused-parameter]
unsigned int size)

The 'size' variable is used only when PAGE_SIZE >= 8192. Add __maybe_unused
to remove the warning.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

ice: Fix transmit for all software offloaded VLANs

Currently the driver does not recognize when there is an 802.1AD VLAN
tag right after the dmac/smac (outermost VLAN tag). If any DCB map is
applied and/or DCB is enabled this is causing the hardware to insert a
VLAN 0 tag after the 802.1AD VLAN tag that is already in the packet.
Fix this by preventing VLAN tag 0 from being added when any VLAN is
already present after dmac/smac (software offloaded) or skb (hardware
offloaded).

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Support IPv4 Flow Director filters

Support the addition and deletion of IPv4 filters.

Supported fields are: src-ip, dst-ip, src-port, and dst-port
Supported flow-types are: tcp4, udp4, sctp4, ip4

Example usage:

ethtool -N eth0 flow-type tcp4 src-ip 192.168.0.55 dst-ip 172.16.0.55 \
src-port 16 dst-port 12 action 32

Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Initialize Flow Director resources

Flow Director allows for redirection based on ntuple rules. Rules are
programmed using the ethtool set-ntuple interface. Supported actions are
redirect to queue and drop.

Setup the initial framework to process Flow Director filters. Create and
allocate resources to manage and program filters to the hardware. Filters
are processed via a sideband interface; a control VSI is created to manage
communication and process requests through the sideband. Upon allocation of
resources, update the hardware tables to accept perfect filters.

Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Rename build_ctob to ice_build_ctob

To make the function easier to identify as being part of the ice driver,
prepend ice to the function name.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Fix casting issues

Change min() macros to min_t() which has compare type specified and it
helps avoid precision loss.

In some cases there was precision loss during calls or assignments.
Some fields in structs were unnecessarily large and gave multiple
warnings.

There were also some minor type differences which are now fixed as well as
some cases where a simple cast was needed.

Callers were were passing data that is a u16 to
ice_sched_cfg_node_bw_alloc() but the function was truncating that to a u8.
Fix that by changing the function to take a u16.

Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Add support for tunnel offloads

Create a boost TCAM entry for each tunnel port in order to get a tunnel
PTYPE. Update netdev feature flags and implement the appropriate logic to
get and set values for hardware offloads.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Add XDP frame size to driver

This driver uses different memory models depending on PAGE_SIZE at
compile time. For PAGE_SIZE 4K it uses page splitting, meaning for
normal MTU frame size is 2048 bytes (and headroom 192 bytes). For
larger MTUs the driver still use page splitting, by allocating
order-1 pages (8192 bytes) for RX frames. For PAGE_SIZE larger than
4K, driver instead advance its rx_buffer->page_offset with the frame
size "truesize".

For XDP frame size calculations, this mean that in PAGE_SIZE larger
than 4K mode the frame_sz change on a per packet basis. For the page
split 4K PAGE_SIZE mode, xdp.frame_sz is more constant and can be
updated once outside the main NAPI loop.

The default setting in the driver uses build_skb(), which provides
the necessary headroom and tailroom for XDP-redirect in RX-frame
(in both modes).

There is one complication, which is legacy-rx mode (configurable via
ethtool priv-flags). There are zero headroom in this mode, which is a
requirement for XDP-redirect to work. The conversion to xdp_frame
(convert_to_xdp_frame) will detect this insufficient space, and
xdp_do_redirect() call will fail. This is deemed acceptable, as it
allows other XDP actions to still work in legacy-mode. In
legacy-mode + larger PAGE_SIZE due to lacking tailroom, we also
accept that xdp_adjust_tail shrink doesn't work.

Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Link: https://lore.kernel.org/bpf/158945347002.97035.328088795813704587.stgit@firesoul

ice: replace "fallthrough" comments with fallthrough reserved word

"fallthrough" comments are used in switch case statements to explicitly
indicate the code is intended to fall through to the following statement.
Different variants of "fallthough" are acceptable, e.g. "fall through",
"fallthrough", "Fall-through". The GCC compiler has an optional warning
(-Wimplicit-fallthrough[=n]) to warn when such a comment is not present;
the default version of which is enabled when compiling the Linux kernel.

There have been recent discussions in kernel mailing lists regarding
replacing non-standardized "fallthrough" comments with the pseudo-reserved
word 'fallthrough' which will be defined as __attribute__ ((fallthrough))
for versions of gcc that support it (i.e. gcc 7 and newer) or as a nop
for versions that do not. Replace "fallthrough" comments with fallthrough
reserved word.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: remove unnecessary fallthrough comments

Fallthrough comments are used to explicitly indicate the code is intended
to flow from one case statement to the next in a switch statement rather
than break out of the switch statement. They are only needed when a case
has one or more statements to execute before falling through to the next
case, not when there is a list of cases for which the same statement(s)
should be executed.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Trivial fixes

This is a collection of trivial fixes including fixing whitespace, typos,
function headers, reverse Christmas tree, etc.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Remove possible null dereference

Commit 1f45ebe0d8fb ("ice: add extra check for null Rx descriptor") moved
the call to ice_construct_skb() under a null check as Coverity reported a
possible use of null skb. However, the original call was not deleted, do so
now.

Fixes: 1f45ebe0d8fb ("ice: add extra check for null Rx descriptor")
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: add extra check for null Rx descriptor

In the case where the hardware gives us a null Rx descriptor, it is
theoretically possible that we could call one of our skb-construction
functions with no data pointer, which would cause a panic.

In real life, this will never happen - we only get null RX
descriptors as the final descriptor in a chain of otherwise-valid
descriptors. When this happens, the skb will be extant and we'll just
call ice_add_rx_frag(), which can deal with empty data buffers.

Unfortunately, Coverity does not have intimate knowledge of our
hardware, so we must add a check here.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Support UDP segmentation offload

Based on the work done by Alex Duyck on other Intel drivers, add code to
support UDP segmentation offload (USO) for the ice driver.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Get rid of ice_cleanup_header

ice_cleanup_hdrs() has been stripped of most of its content, it only serves
as a wrapper for eth_skb_pad(). We can get rid of it altogether and
simplify the codebase.

Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: add build_skb() support

Driver is now prepared for building the skb around the existing Rx
buffer, so introduce the ice_build_skb responsible for it. Make use of
XDP's data_meta as well.

I've observed around 30% less CPU consumption with build_skb Rx path, in
comparison to legacy Rx. What stands behind such result is the avoidance
of flow_dissector (which we were diving into via eth_get_headlen) and no
memcpy calls.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: introduce frame padding computation logic

Take into account the underlying architecture specific settings and
based on that calculate the possible padding that can be supplied.
Typically, for x86 and standard MTU size we will end up with 192 bytes
of headroom. This is the same behavior as our other drivers have and we
can dedicate it for XDP purposes.

Furthermore, introduce the Rx ring flag for indicating whether build_skb
is used on particular. Based on that invoke the routines for padding
calculation.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: introduce legacy Rx flag

Add an ethtool "legacy-rx" priv flag for toggling the Rx path. This
control knob will be mainly used for build_skb usage as well as buffer
size/MTU manipulation.

In preparation for adding build_skb support in a way that it takes
care of how we set the values of max_frame and rx_buf_len fields of
struct ice_vsi. Specifically, in this patch mentioned fields are set to
values that will allow us to provide headroom and tailroom in-place.

This can be mostly broken down onto following:
- for legacy-rx "on" ethtool control knob, old behaviour is kept;
- for standard 1500 MTU size configure the buffer of size 1536, as
network stack is expecting the NET_SKB_PAD to be provided and
NET_IP_ALIGN can have a non-zero value (these can be typically equal
to 32 and 2, respectively);
- for larger MTUs go with max_frame set to 9k and configure the 3k
buffer in case when PAGE_SIZE of underlying arch is less than 8k; 3k
buffer is implying the need for order 1 page, so that our page
recycling scheme can still be applied;

With that said, substitute the hardcoded ICE_RXBUF_2048 and PAGE_SIZE
values in DMA API that we're making use of with rx_ring->rx_buf_len and
ice_rx_pg_size(rx_ring). The latter is an introduced helper for
determining the page size based on its order (which was figured out via
ice_rx_pg_order). Last but not least, take care of truesize calculation.

In the followup patch the headroom/tailroom computation logic will be
introduced.

This change aligns the buffer and frame configuration with other Intel
drivers, most importantly with iavf.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Add support for AF_XDP

Add zero copy AF_XDP support. This patch adds zero copy support for
Tx and Rx; code for zero copy is added to ice_xsk.h and ice_xsk.c.

For Tx, implement ndo_xsk_wakeup. As with other drivers, reuse
existing XDP Tx queues for this task, since XDP_REDIRECT guarantees
mutual exclusion between different NAPI contexts based on CPU ID. In
turn, a netdev can XDP_REDIRECT to another netdev with a different
NAPI context, since the operation is bound to a specific core and each
core has its own hardware ring.

For Rx, allocate frames as MEM_TYPE_ZERO_COPY on queues that AF_XDP is
enabled.

Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Move common functions to ice_txrx_lib.c

In preparation of AF XDP, move functions that will be used both by skb and
zero-copy paths to a new file called ice_txrx_lib.c. This allows us to
avoid using ifdefs to control the staticness of said functions.

Move other functions (ice_rx_csum, ice_rx_hash and ice_ptype_to_htype)
called only by the moved ones to the new file as well.

Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Add support for XDP

Add support for XDP. Implement ndo_bpf and ndo_xdp_xmit. Upon load of
an XDP program, allocate additional Tx rings for dedicated XDP use.
The following actions are supported: XDP_TX, XDP_DROP, XDP_REDIRECT,
XDP_PASS, and XDP_ABORTED.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: small efficiency fixes

Add a small bit of efficiency to the code by adding a
prefetch of the port_info structure in order to help
avoid a cache miss a little later on in execution.

Also add an unlikely statement to a branch which
generally will never happen in normal operation.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: move code closer together

This is a simple patch to move the assignment to a local variable
closer to the site where the local variable is used. This
can help readability and also maybe performance, although the
performance enhancement is really dependent upon the compiler.

No functional change.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: clean up arguments

There are a couple of functions that don't need two arguments
passed in when the second argument already had access to
the pointer pointed to by the first.

Remove the unnecessary arguments.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Allow egress control packets from PF_VSI

For control packets (i.e. LLDP packets) to be able to egress
from the main VSI, a bit has to be set in the TX_descriptor.
This should only be done for the main VSI and only if the
FW LLDP agent is disabled. A bit to allow this also has to
be set in the VSI context.

Add the logic to add the necessary bits in the VSI context
for the PF_VSI and the TX_descriptors for control packets
egressing the PF_VSI.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: allow empty Rx descriptors

In some circumstances, the hardware will hand us a receive descriptor
which has no data attached, but is otherwise valid. The receive code was
improperly ignoring these descriptors, which result in an infinite loop.

To fix this, change the receive code to process all descriptors,
regardless of the size of the associated data. Add checks to the
memory-handling functions to allow for zero size.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Set WB_ON_ITR when we don't re-enable interrupts

Currently when busy polling is enabled we aren't setting/enabling
WB_ON_ITR in the driver. This doesn't break the driver, but it does
cause issues. If we don't enable WB_ON_ITR mode we will still get
write-backs from hardware during polling when a cache line has been
filled, but if a cache line is not filled we will not get the
write-back because WB_ON_ITR is not set. Fix this by enabling
WB_ON_ITR in the driver when interrupts are disabled.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Assume that more than one Rx queue is rare in ice_napi_poll

Currently we divide budget by the number of Rx queues per Rx ring
container in ice_napi_poll even if there is only 1. This is an
unnecessary divide for the normal case of 1 Rx ring per Rx ring
container. Fix this by using an unlikely() call in the case where we
actually need to divide.

Also, we will always set budget_per_ring even if there are no Rx rings
in the Rx ring container so we don't need to initialize it to 0.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Remove unnecessary flag ICE_FLAG_MSIX_ENA

This flag is not needed and is called every time we re-enable interrupts
in the hotpath so remove it. Also remove ice_vsi_req_irq() because it
was a wrapper function for ice_vsi_req_irq_msix() whose sole purpose was
checking the ICE_FLAG_MSIX_ENA flag.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Remove duplicate code in ice_alloc_rx_bufs

Currently if the call to ice_alloc_mapped_page() fails we jump to the
no_buf label, possibly call ice_release_rx_desc(), and return true
indicating that there is more work to do. In the success case we just
fall out of the while loop, possibly call ice_alloc_mapped_page(), and
return false saying we exhausted cleaned_count. This flow can be
improved by breaking if ice_alloc_mapped_page() fails and then the flow
outside of the while loop is the same for the failure and success case.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Only bump Rx tail and release buffers once per napi_poll

Currently we bump the Rx tail and release/give buffers to hardware every
16 descriptors. This causes us to bump Rx tail up to 4 times per
napi_poll call. Also we are always bumping tail on an odd index and this
is a problem because hardware ignores the lower 3 bits in the QRX_TAIL
register. This is making it so hardware sees tail bumps only every 8
descriptors. Instead lets only bump Rx tail once per napi_poll if
the value aligns with hardware's expectations of the lower 3 bits being
cleared. Also only release/give Rx buffers once per napi_poll call.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net: Use skb accessors in network drivers

In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.

Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ice: Trivial cosmetic changes

This patch mostly capitalizes abbreviations in code comments. Fixed some
typos and removed some unnecessary newlines as well.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Resolve static analysis warning

Some static analysis tools can complain when doing a bitop assignment using
operands of different sizes. Fix that.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Suppress false-positive style issues reported by static analyzer

A recent version of cppcheck falsely reports-
Variable ip.hdr is assigned a value that is never used.

ip is a union so the pointer ip.hdr is actually used when referenced as
ip.v4 and ip.v6. Silence these false reports when using cppcheck with the
--inline-suppr command-line option.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Add reg_idx variable in ice_q_vector structure

Every time we want to re-enable interrupts and/or write to a register
that requires an interrupt vector's hardware index we do the following:

vsi->hw_base_vector + q_vector->v_idx

This is a wasteful operation, especially in the hot path. Fix this by
adding a u16 reg_idx member to the ice_q_vector structure and make the
necessary changes to make this work.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net: pass net_device argument to the eth_get_headlen

Update all users of eth_get_headlen to pass network device, fetch
network namespace from it and pass it down to the flow dissector.
This commit is a noop until administrator inserts BPF flow dissector
program.

Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

ice: Calculate ITR increment based on direct calculation

Currently when calculating how much to increment ITR by inside of
ice_update_itr() we do some estimations and intermediate
calculations. Instead of doing estimations, just do the
calculation directly. This allows for a more accurate value and it
makes it easier for the next person to understand and update.

Also, remove the dividing the ITR value by 2 when latency
driven because the ITR values are already so low for 100Gbps
speed. This should help get to the desired ITR value faster.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Add priority information into VLAN header

This patch introduces a new function ice_tx_prepare_vlan_flags_dcb to
insert 802.1p priority information into the VLAN header

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Fix incorrect use of abbreviations

Capitalize abbreviations and spell out some that aren't obvious.

Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers: Remove explicit invocations of mmiowb()

mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:

@mmiowb@
@@
- mmiowb();

and invoked as:

$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done

NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

net: move skb->xmit_more hint to softnet data

There are two reasons for this.

First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.

Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().

We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.

Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.

skb->xmit_more is retained (but always 0) to not cause build breakage.

This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions. Remaining drivers are converted in the next patches.

Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

ice: Remove unnecessary braces

Single statement if conditions don't need braces. Remove it.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Audit hotpath structures with pahole

Currently the ice_q_vector structure and ice_ring_container structure
are taking up more space than necessary due to cache alignment holes
and unnecessary variables respectively. This is not helping the
driver's performance. The following fixes were done to improve cache
alignment, reduce wasted space, and increase performance.

1. Remove the ice_latency_range enum as it is unused.
2. Remove the latency_range variable in the ice_ring_container structure.
3. Change the size of the itr_idx in the ice_ring_container structure
from an int to an u16. This reduced the size of ice_ring_container
structure to 32 Bytes so it has no holes or padding.
4. Re-arrange the ice_q_vector structure using pahole to align
members as best as possible in regards to 64 Byte cache line size.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Fix for adaptive interrupt moderation

commit 63f545ed1285 ("ice: Add support for adaptive interrupt moderation")
was meant to add support for adaptive interrupt moderation but there was
an error on my part while formatting the patch, and thus only part of the
patch ended up being submitted.

This patch rectifies the error by adding the rest of the code.

Fixes: 63f545ed1285 ("ice: Add support for adaptive interrupt moderation")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: map Rx buffer pages with DMA attributes

Provide DMA_ATTR_WEAK_ORDERING and DMA_ATTR_SKIP_CPU_SYNC attributes to
the DMA API during the mapping operations on Rx side. With this change
the non-x86 platforms will be able to sync only with what is being used
(2k buffer) instead of entire page. This should yield a slight
performance improvement.

Furthermore, DMA unmap may destroy the changes that were made to the
buffer by CPU when platform is not a x86 one. DMA_ATTR_SKIP_CPU_SYNC
attribute usage fixes this issue.

Also add a sync_single_for_device call during the Rx buffer assignment,
to make sure that the cache lines are cleared before device attempting
to write to the buffer.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Limit the ice_add_rx_frag to frag addition

Refactor ice_fetch_rx_buf and ice_add_rx_frag in a way that we have
standalone functions that do either the skb construction or frag
addition to previously constructed skb.

The skb handling between rx_bufs is spread among various functions. The
ice_get_rx_buf will retrieve the skb pointer from rx_buf and if it is a
NULL pointer then we do the ice_construct_skb, otherwise we add a frag
to the current skb via ice_add_rx_frag. Then, on the ice_put_rx_buf the
skb pointer that belongs to rx_buf will be cleared. Moving further, if
the current frame is not EOP frame we assign the current skb to the
rx_buf that is pointed by updated next_to_clean indicator.

What is more during the buffer reuse let's assign each member of
ice_rx_buf individually so we avoid the unnecessary copy of skb.

Last but not least, this logic split will allow us for better code reuse
when adding a support for build_skb.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Gather the rx buf clean-up logic for better reuse

Pull out the code responsible for page counting and buffer recycling so
that it will be possible to clean up the Rx buffers in cases where we
won't allocate skb (ex. XDP)

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Introduce bulk update for page count

{get,put}_page are atomic operations which we use for page count
handling. The current logic for refcount handling is that we increment
it when passing a skb with the data from the first half of page up to
netstack and recycle the second half of page. This operation protects us
from losing a page since the network stack can decrement the refcount of
page from skb.

The performance can be gently improved by doing the bulk updates of
refcount instead of doing it one by one. During the buffer initialization,
maximize the page's refcount and don't allow the refcount to become
less than two.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Get rid of ice_pull_tail

Instead of adding a frag and later when dealing with EOP frame accessing
that frag in order to copy the headers onto linear part of skb, we can do
this in ice_add_rx_frag in case where the data_len is still 0 and frame
won't fit onto the linear part as a whole.

Function comment of ice_pull_tail was a bit misleading because of
mentioned optimizations that can be performed (drop a frag/maintaining
accurate truesize of skb) - it seems that this part of logic was dropped
and the comment was not updated to reflect this change.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Pull out page reuse checks onto separate function

Introduce ice_can_reuse_rx_page which will verify whether the page can
be reused and return the boolean result to caller.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Retrieve rx_buf in separate function

Introduce ice_get_rx_buf, which will fetch the Rx buffer and do the DMA
synchronization. Length of the packet that hardware Rx descriptor
contains is now read in ice_clean_rx_irq, so we can feed ice_get_rx_buf
with it and resign from rx_desc passed as argument in ice_fetch_rx_buf
and ice_add_rx_frag.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: fix some function prototype and signature style issues

Put the return type on a separate line for function prototypes and
signatures that would exceed the 80-character limit if both were on
the same line.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Determine descriptor count and ring size based on PAGE_SIZE

Currently we set the default number of Tx and Rx descriptors to 128 by
default. For Rx this amounts to a full page (assuming 4K pages) because
each Rx descriptor is 32 Bytes, but for Tx it only amounts to a half
page because each Tx descriptor is 16 Bytes (assuming 4K pages).
Instead of assuming 4K pages, determine the ring size and the number of
descriptors for Tx and Rx based on a calculation using the PAGE_SIZE,
ICE_MAX_NUM_DESC, and ICE_REQ_DESC_MULTIPLE. This change is being made
to improve the performance of the driver when using the default
settings.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: fix numeric overflow warning

When compiling and analyzing the driver on newer kernels, a static
analyzer warns about the following "numeric overflow" issues:

"The result of expression: 'budget-1' generates 4-byte type while casting
to a bigger size of 8-byte".

"The result of expression: '*words-words_read' generates 4-byte type
while casting to a bigger size of 8-byte".

Fix them both.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: sizeof(<type>) should be avoided

With sizeof(), it is preferable to use the variable of type <type> instead
of sizeof(<type>).

There are multiple places where a temporary variable is used to hold a
'size' value which is then used for a subsequent alloc/memset. Get rid
of the temporary variable by calculating size as part of the alloc/memset
statement.

Also remove unnecessary type-cast.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Offload SCTP checksum

This patch adds the ability to offload SCTP checksum calculations to the
NIC.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Add support for adaptive interrupt moderation

Currently the driver does not support adaptive/dynamic interrupt
moderation. This patch adds support for this. Also, adaptive/dynamic
interrupt moderation is turned on by default upon driver load.

In order to support adaptive interrupt moderation, two functions were
added, ice_update_itr() and ice_itr_divisor(). These are used to
determine the current packet load and to determine a divisor based
on link speed respectively.

This patch also adds the ICE_ITR_GRAN_S define that is used in the
hot-path when setting a new ITR value. The shift is used to pet two
birds with one hand, set the ITR value while re-enabling the
interrupt. Also, the ICE_ITR_GRAN_S is defined as 1 because the device
has a ITR granularity of 2usecs.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ethernet/intel: consolidate NAPI and NAPI exit

While reviewing code, I noticed that Eric Dumazet recommends that
drivers check the return code of napi_complete_done, and use that
to decide to enable interrupts or not when exiting poll. One of
the Intel drivers was already fixed (ixgbe).

Upon looking at the Intel drivers as a whole, we are handling our
polling and NAPI exit in a few different ways based on whether we
have multiqueue and whether we have Tx cleanup included. Several
drivers had the bug of exiting NAPI with return 0, which appears
to mess up the accounting in the stack.

Consolidate all the NAPI routines to do best known way of exiting
and to just mostly look like each other.
1) check return code of napi_complete_done to control interrupt enable
2) return the actual amount of work done.
3) return budget immediately if need NAPI poll again

Tested the changes on e1000e with a high interrupt rate set, and
it shows about an 8% reduction in the CPU utilization when busy
polling because we aren't re-enabling interrupts when we're about
to be polled.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Use Tx|Rx in comments

In code comments, use Tx|Rx instead of tx|rx

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Cosmetic formatting changes

1. Fix several cases of double spacing
2. Fix typos
3. Capitalize abbreviations

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Fix return value from NAPI poll

ice_napi_poll is hard-coded to return zero when it's done. It should
instead return the work done (if any work was done). The only time it
should return zero is if an interrupt or poll is handled and no work
is performed. So change the return value to be the minimum of work
done or budget-1.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Fix the bytecount sent to netdev_tx_sent_queue

Currently if the driver does a TSO offload the bytecount sent to
netdev_tx_sent_queue will be incorrect. This is because in ice_tso we
overwrite the initial value that we set in ice_tx_map. This creates a
mismatch between the Tx and Tx clean flow. In the Tx clean flow we
calculate the bytecount (called total_bytes) as we clean the
descriptors so the value used in the Tx clean path is correct. Fix this
by using += in ice_tso instead of =. This fixes the mismatch in
bytecount mentioned above.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Fix tx_timeout in PF driver

Prior to this commit the driver was running into tx_timeouts when a
queue was stressed enough. This was happening because the HW tail
and SW tail (NTU) were incorrectly out of sync. Consequently this was
causing the HW head to collide with the HW tail, which to the hardware
means that all descriptors posted for Tx have been processed.

Due to the Tx logic used in the driver SW tail and HW tail are allowed
to be out of sync. This is done as an optimization because it allows the
driver to write HW tail as infrequently as possible, while still
updating the SW tail index to keep track. However, there are situations
where this results in the tail never getting updated, resulting in Tx
timeouts.

Tx HW tail write condition:
if (netif_xmit_stopped(txring_txq(tx_ring) || !skb->xmit_more)
writel(sw_tail, tx_ring->tail);

An issue was found in the Tx logic that was causing the afore mentioned
condition for updating HW tail to never happen, causing tx_timeouts.

In ice_xmit_frame_ring we calculate how many descriptors we need for the
Tx transaction based on the skb the kernel hands us. This is then passed
into ice_maybe_stop_tx along with some extra padding to determine if we
have enough descriptors available for this transaction. If we don't then
we return -EBUSY to the stack, otherwise we move on and eventually
prepare the Tx descriptors accordingly in ice_tx_map and set
next_to_watch. In ice_tx_map we make another call to ice_maybe_stop_tx
with a value of MAX_SKB_FRAGS + 4. The key here is that this value is
possibly less than the value we sent in the first call to
ice_maybe_stop_tx in ice_xmit_frame_ring. Now, if the number of unused
descriptors is between MAX_SKB_FRAGS + 4 and the value used in the first
call to ice_maybe_stop_tx in ice_xmit_frame_ring then we do not update
the HW tail because of the "Tx HW tail write condition" above. This is
because in ice_maybe_stop_tx we return success from ice_maybe_stop_tx
instead of calling __ice_maybe_stop_tx and subsequently calling
netif_stop_subqueue, which sets the __QUEUE_STATE_DEV_XOFF bit. This
bit is then checked in the "Tx HW tail write condition" by calling
netif_xmit_stopped and subsequently updating HW tail if the
afore mentioned bit is set.

In ice_clean_tx_irq, if next_to_watch is not NULL, we end up cleaning
the descriptors that HW sets the DD bit on and we have the budget. The
HW head will eventually run into the HW tail in response to the
description in the paragraph above.

The next time through ice_xmit_frame_ring we make the initial call to
ice_maybe_stop_tx with another skb from the stack. This time we do not
have enough descriptors available and we return NETDEV_TX_BUSY to the
stack and end up setting next_to_watch to NULL.

This is where we are stuck. In ice_clean_tx_irq we never clean anything
because next_to_watch is always NULL and in ice_xmit_frame_ring we never
update HW tail because we already return NETDEV_TX_BUSY to the stack and
eventually we hit a tx_timeout.

This issue was fixed by making sure that the second call to
ice_maybe_stop_tx in ice_tx_map is passed a value that is >= the value
that was used on the initial call to ice_maybe_stop_tx in
ice_xmit_frame_ring. This was done by adding the following defines to
make the logic more clear and to reduce the chance of mucking this up
again:

ICE_CACHE_LINE_BYTES 64
ICE_DESCS_PER_CACHE_LINE (ICE_CACHE_LINE_BYTES / \
sizeof(struct ice_tx_desc))
ICE_DESCS_FOR_CTX_DESC 1
ICE_DESCS_FOR_SKB_DATA_PTR 1

The ICE_CACHE_LINE_BYTES being 64 is an assumption being made so we
don't have to figure this out on every pass through the Tx path. Instead
I added a sanity check in ice_probe to verify cache line size and print
a message if it's not 64 Bytes. This will make it easier to file issues
if they are seen when the cache line size is not 64 Bytes when reading
from the GLPCI_CNF2 register.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Add support for Tx hang, Tx timeout and malicious driver detection

When a malicious operation is detected, the firmware triggers an
interrupt, which is then picked up by the service task (specifically by
ice_handle_mdd_event). A reset is scheduled if required.

Tx hang detection works in a similar way, except the logic here monitors
the VSI's Tx queues and tries to revive them if stalled. If the hang is
not resolved, the kernel eventually calls ndo_tx_timeout, which is
handled by ice_tx_timeout.

Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Add support for VLANs and offloads

This patch adds support for VLANs. When a VLAN is created a switch filter
is added to direct the VLAN traffic to the corresponding VSI. When a VLAN
is deleted, the filter is deleted as well.

This patch also adds support for the following hardware offloads.
1) VLAN tag insertion/stripping
2) Receive Side Scaling (RSS)
3) Tx checksum and TCP segmentation
4) Rx checksum

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Implement transmit and NAPI support

This patch implements ice_start_xmit (the handler for ndo_start_xmit) and
related functions. ice_start_xmit ultimately calls ice_tx_map, where the
Tx descriptor is built and posted to the hardware by bumping the ring tail.

This patch also implements ice_napi_poll, which is invoked when there's an
interrupt on the VSI's queues. The interrupt can be due to either a
completed Tx or an Rx event. In case of a completed Tx/Rx event, resources
are reclaimed. Additionally, in case of an Rx event, the skb is fetched
and passed up to the network stack.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Configure VSIs for Tx/Rx

This patch configures the VSIs to be able to send and receive
packets by doing the following:

1) Initialize flexible parser to extract and include certain
fields in the Rx descriptor.

2) Add Tx queues by programming the Tx queue context (implemented in
ice_vsi_cfg_txqs). Note that adding the queues also enables (starts)
the queues.

3) Add Rx queues by programming Rx queue context (implemented in
ice_vsi_cfg_rxqs). Note that this only adds queues but doesn't start
them. The rings will be started by calling ice_vsi_start_rx_rings on
interface up.

4) Configure interrupts for VSI queues.

5) Implement ice_open and ice_stop.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>