ice: Fix tx queue rate limit when TCs are configured

Configuring tx_maxrate via sysfs interface
/sys/class/net/eth0/queues/tx-1/tx_maxrate was not working when
TCs are configured because always main VSI was being used. Fix by
using correct VSI in ice_set_tx_maxrate when TCs are configured.

Fixes: 1ddef455f4a8 ("ice: Add NDO callback to set the maximum per-queue bitrate")
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: allow matching on meta data

Add meta data matching criteria in the same place as protocol matching
criteria. There is no need to add meta data as special words after
parsing all lookups. Trade meta data in the same why as other lookups.

The one difference between meta data lookups and protocol lookups is
that meta data doesn't impact how the packets looks like. Because of that
ignore it when filling testing packet.

Match on tunnel type meta data always if tunnel type is different than
TNL_LAST.

Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Support drop action

Currently the drop action is supported only in switchdev mode.
Add support for offloading receive filters with action drop
in ADQ/non-ADQ modes. This is in addition to other actions
such as forwarding to a VSI (ADQ) or a queue (ADQ/non-ADQ).

Also renamed 'ch_vsi' to 'dest_vsi' as it is valid for multiple
actions such as forward to vsi/queue which may/may not create a
channel vsi.

Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Enable RX queue selection using skbedit action

This patch uses TC skbedit queue_mapping action to support
forwarding packets to a device queue. Such filters with action
forward to queue will be the highest priority switch filter in
HW.
Example:
$ tc filter add dev ens4f0 protocol ip ingress flower\
dst_ip 192.168.1.12 ip_proto tcp dst_port 5001\
action skbedit queue_mapping 5 skip_sw

The above command adds an ingress filter, incoming packets
qualifying the match will be accepted into queue 5. The queue
number is in decimal format.

Refactored ice_add_tc_flower_adv_fltr() to consolidate code with
action FWD_TO_VSI and FWD_TO QUEUE.

Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

ice: Add support for VLAN priority filters in switchdev

Enable support for adding TC rules that filter on the VLAN priority
in switchdev mode.

VLAN priority are the first 3 bits of 16b switch field vector word
which contain also vlan id value within its last 12 bits.
When getting vlan priority value from tc match.key it
has to be shifted first to proper bits positions (by VLAN_PRIO_SHIFT)
and then can be added to the joint 'vlan' field in ice_vlan_hdr
in lookup element.

The mask of lookup changes accordingly.
0x0FFF - when only vlan id is added in filter
0xE000 - when only vlan priority is added in filter
0xEFFF - when both these values are specified

Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Add L2TPv3 hardware offload support

Add support for offloading packets based on L2TPv3 session id in switchdev
mode.

Example filter:
tc filter add dev $PF1 ingress prio 1 protocol ip flower ip_proto l2tp \
l2tpv3_sid 1234 skip_sw action mirred egress redirect dev $VF1_PR

Changes in iproute2 are required to be able to specify l2tpv3_sid.

ICE COMMS DDP package is required to create a filter as it contains L2TPv3
profiles.

Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

ice: Add support for ip TTL & ToS offload

Add support for parsing TTL and ToS (Hop Limit and Traffic Class) tc fields
and matching on those fields in filters. Incomplete part of implementation
was already in place (getting enc_ip and enc_tos from flow_match_ip and
writing them to filter header).

Note: matching on ipv6 ip_ttl, enc_ttl and enc_tos is currently not
supported by the DDP package.

Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Add support for PPPoE hardware offload

Add support for creating PPPoE filters in switchdev mode. Add support
for parsing PPPoE and PPP-specific tc options: pppoe_sid and ppp_proto.

Example filter:
tc filter add dev $PF1 ingress protocol ppp_ses prio 1 flower pppoe_sid \
1234 ppp_proto ip skip_sw action mirred egress redirect dev $VF1_PR

Changes in iproute2 are required to use the new fields.

ICE COMMS DDP package is required to create a filter as it contains PPPoE
profiles. Added a warning message when loaded DDP package does not contain
required profiles.

Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Add support for VLAN TPID filters in switchdev

Enable support for adding TC rules that filter on the VLAN tag type
in switchdev mode.

Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Add support for double VLAN in switchdev

Enable support for adding TC rules with both C-tag and S-tag that can
filter on the inner and outer VLAN in QinQ for basic packets (not
tunneled cases).

Signed-off-by: Wiktor Pilarczyk <wiktor.pilarczyk@intel.com>
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Support GTP-U and GTP-C offload in switchdev

Add support for creating filters for GTP-U and GTP-C in switchdev mode. Add
support for parsing GTP-specific options (QFI and PDU type) and TEID.

By default, a filter for GTP-U will be added. To add a filter for GTP-C,
specify enc_dst_port = 2123, e.g.:

tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
enc_dst_port 2123 action mirred egress redirect dev $VF1_PR

Note: GTP-U with outer IPv6 offload is not supported yet.
Note: GTP-U with no payload offload is not supported yet.

Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: VXLAN and Geneve TC support

Add definition for VXLAN and Geneve dummy packet. Define VXLAN and
Geneve type of fields to match on correct UDP tunnel header.

Parse tunnel specific fields from TC tool like outer MACs, outer IPs,
outer destination port and VNI. Save values and masks in outer header
struct and move header pointer to inner to simplify parsing inner
values.

There are two cases for redirect action:
- from uplink to VF - TC filter is added on tunnel device
- from VF to uplink - TC filter is added on PR, for this case check if
redirect device is tunnel device

VXLAN example:
- create tunnel device
ip l add $VXLAN_DEV type vxlan id $VXLAN_VNI dstport $VXLAN_PORT \
dev $PF
- add TC filter (in switchdev mode)
tc filter add dev $VXLAN_DEV protocol ip parent ffff: flower \
enc_dst_ip $VF1_IP enc_key_id $VXLAN_VNI action mirred egress \
redirect dev $VF1_PR

Geneve example:
- create tunnel device
ip l add $GENEVE_DEV type geneve id $GENEVE_VNI dstport $GENEVE_PORT \
remote $GENEVE_IP
- add TC filter (in switchdev mode)
tc filter add dev $GENEVE_DEV protocol ip parent ffff: flower \
enc_key_id $GENEVE_VNI dst_ip $GENEVE1_IP action mirred egress \
redirect dev $VF1_PR

Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: support for indirect notification

Implement indirect notification mechanism to support offloading TC rules
on tunnel devices.

Keep indirect block list in netdev priv. Notification will call setting
tc cls flower function. For now we can offload only ingress type. Return
not supported for other flow block binder.

Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Add tc-flower filter support for channel

Add support to add/delete channel specific filter using tc-flower.
For now, only supported action is "skip_sw hw_tc <tc_num>"

Filter criteria is specific to channel and it can be
combination of L3, L3+L4, L2+L4.

Example:
MATCH criteria Action
---------------------------
src and/or dest IPv4[6]/mask -> Forward to "hw_tc <tc_num>"
dest IPv4[6]/mask + dest L4 port -> Forward to "hw_tc <tc_num>"
dest MAC + dest L4 port -> Forward to "hw_tc <tc_num>"
src IPv4[6]/mask + src L4 port -> Forward to "hw_tc <tc_num>"
src MAC + src L4 port -> Forward to "hw_tc <tc_num>"

Adding tc-flower filter for channel using "hw_tc"
-------------------------------------------------
tc qdisc add dev <ethX> clsact

Above two steps are only needed the first time when adding
tc-flower filter.

tc filter add dev <ethX> protocol ip ingress prio 1 flower \
dst_ip 192.168.0.1/32 ip_proto tcp dst_port 5001 \
skip_sw hw_tc 1

tc filter show dev <ethX> ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1 hw_tc 1
eth_type ipv4
ip_proto tcp
dst_ip 192.168.0.1
dst_port 5001
skip_sw
in_hw in_hw_count 1

Delete specific filter:
-------------------------
tc filter del dev <ethx> ingress pref 1 handle 0x1 flower

Delete All filters:
------------------
tc filter del dev <ethX> ingress

Co-developed-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: ndo_setup_tc implementation for PR

Add tc-flower support for VF port representor devices.

Implement ndo_setup_tc callback for TC HW offload on VF port representors
devices. Implemented both methods: add and delete tc-flower flows.

Mark NETIF_F_HW_TC bit in net device's feature set to enable offload TC
infrastructure for port representor.

Implement TC filters replay function required to restore filters settings
while switchdev configuration is rebuilt.

Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: ndo_setup_tc implementation for PF

Implement ndo_setup_tc net device callback for TC HW offload on PF device.

ndo_setup_tc provides support for HW offloading various TC filters.
Add support for configuring the following filter with tc-flower:
- default L2 filters (src/dst mac addresses, ethertype, VLAN)
- variations of L3, L3+L4, L2+L3+L4 filters using advanced filters
(including ipv4 and ipv6 addresses).

Allow for adding/removing TC flows when PF device is configured in
eswitch switchdev mode. Two types of actions are supported at the
moment: FLOW_ACTION_DROP and FLOW_ACTION_REDIRECT.

Co-developed-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>