ice: sync netdev filters after clearing VSI

In driver reload path the netdev isn't removed, but VSI is. Remove
filters on netdev right after removing them on VSI.

Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Ignore error message when setting same promiscuous mode

Commit 1273f89578f2 ("ice: Fix broken IFF_ALLMULTI handling")
introduced new checks when setting/clearing promiscuous mode. But if the
requested promiscuous mode setting already exists, an -EEXIST error
message would be printed. This is incorrect because promiscuous mode is
either on/off and shouldn't print an error when the requested
configuration is already set.

This can happen when removing a bridge with two bonded interfaces and
promiscuous most isn't fully cleared from VLAN VSI in hardware.

Fix this by ignoring cases where requested promiscuous mode exists.

Fixes: 1273f89578f2 ("ice: Fix broken IFF_ALLMULTI handling")
Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Link: https://lore.kernel.org/all/CAK8fFZ7m-KR57M_rYX6xZN39K89O=LGooYkKsu6HKt0Bs+x6xQ@mail.gmail.com/
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Fix broken IFF_ALLMULTI handling

Handling of all-multicast flag and associated multicast promiscuous
mode is broken in ice driver. When an user switches allmulticast
flag on or off the driver checks whether any VLANs are configured
over the interface (except default VLAN 0).

If any extra VLANs are registered it enables multicast promiscuous
mode for all these VLANs (including default VLAN 0) using
ICE_SW_LKUP_PROMISC_VLAN look-up type. In this situation all
multicast packets tagged with known VLAN ID or untagged are received
and multicast packets tagged with unknown VLAN ID ignored.

If no extra VLANs are registered (so only VLAN 0 exists) it enables
multicast promiscuous mode for VLAN 0 and uses ICE_SW_LKUP_PROMISC
look-up type. In this situation any multicast packets including
tagged ones are received.

The driver handles IFF_ALLMULTI in ice_vsi_sync_fltr() this way:

ice_vsi_sync_fltr() {
...
if (changed_flags & IFF_ALLMULTI) {
if (netdev->flags & IFF_ALLMULTI) {
if (vsi->num_vlans > 1)
ice_set_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
else
ice_set_promisc(..., ICE_MCAST_PROMISC_BITS);
} else {
if (vsi->num_vlans > 1)
ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
else
ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS);
}
}
...
}

The code above depends on value vsi->num_vlan that specifies number
of VLANs configured over the interface (including VLAN 0) and
this is problem because that value is modified in NDO callbacks
ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid().

Scenario 1:
1. ip link set ens7f0 allmulticast on
2. ip link add vlan10 link ens7f0 type vlan id 10
3. ip link set ens7f0 allmulticast off
4. ip link set ens7f0 allmulticast on

[1] In this scenario IFF_ALLMULTI is enabled and the driver calls
ice_set_promisc(..., ICE_MCAST_PROMISC_BITS) that installs
multicast promisc rule with non-VLAN look-up type.
[2] Then VLAN with ID 10 is added and vsi->num_vlan incremented to 2
[3] Command switches IFF_ALLMULTI off and the driver calls
ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS) but this
call is effectively NOP because it looks for multicast promisc
rules for VLAN 0 and VLAN 10 with VLAN look-up type but no such
rules exist. So the all-multicast remains enabled silently
in hardware.
[4] Command tries to switch IFF_ALLMULTI on and the driver calls
ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS) but this call
fails (-EEXIST) because non-VLAN multicast promisc rule already
exists.

Scenario 2:
1. ip link add vlan10 link ens7f0 type vlan id 10
2. ip link set ens7f0 allmulticast on
3. ip link add vlan20 link ens7f0 type vlan id 20
4. ip link del vlan10 ; ip link del vlan20
5. ip link set ens7f0 allmulticast off

[1] VLAN with ID 10 is added and vsi->num_vlan==2
[2] Command switches IFF_ALLMULTI on and driver installs multicast
promisc rules with VLAN look-up type for VLAN 0 and 10
[3] VLAN with ID 20 is added and vsi->num_vlan==3 but no multicast
promisc rules is added for this new VLAN so the interface does
not receive MC packets from VLAN 20
[4] Both VLANs are removed but multicast rule for VLAN 10 remains
installed so interface receives multicast packets from VLAN 10
[5] Command switches IFF_ALLMULTI off and because vsi->num_vlan is 1
the driver tries to remove multicast promisc rule for VLAN 0
with non-VLAN look-up that does not exist.
All-multicast looks disabled from user point of view but it
is partially enabled in HW (interface receives all multicast
packets either untagged or tagged with VLAN ID 10)

To resolve these issues the patch introduces these changes:
1. Adds handling for IFF_ALLMULTI to ice_vlan_rx_add_vid() and
ice_vlan_rx_kill_vid() callbacks. So when VLAN is added/removed
and IFF_ALLMULTI is enabled an appropriate multicast promisc
rule for that VLAN ID is added/removed.
2. In ice_vlan_rx_add_vid() when first VLAN besides VLAN 0 is added
so (vsi->num_vlan == 2) and IFF_ALLMULTI is enabled then look-up
type for existing multicast promisc rule for VLAN 0 is updated
to ICE_MCAST_VLAN_PROMISC_BITS.
3. In ice_vlan_rx_kill_vid() when last VLAN besides VLAN 0 is removed
so (vsi->num_vlan == 1) and IFF_ALLMULTI is enabled then look-up
type for existing multicast promisc rule for VLAN 0 is updated
to ICE_MCAST_PROMISC_BITS.
4. Both ice_vlan_rx_{add,kill}_vid() have to run under ICE_CFG_BUSY
bit protection to avoid races with ice_vsi_sync_fltr() that runs
in ice_service_task() context.
5. Bit ICE_VSI_VLAN_FLTR_CHANGED is use-less and can be removed.
6. Error messages added to ice_fltr_*_vsi_promisc() helper functions
to avoid them in their callers
7. Small improvements to increase readability

Fixes: 5eda8afd6bcc ("ice: Add support for PF/VF promiscuous mode")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ice: Use the proto argument for VLAN ops

Currently the proto argument is unused. This is because the driver only
supports 802.1Q VLAN filtering. This policy is enforced via netdev
features that the driver sets up when configuring the netdev, so the
proto argument won't ever be anything other than 802.1Q. However, this
will allow for future iterations of the driver to seemlessly support
802.1ad filtering. Begin using the proto argument and extend the related
structures to support its use.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Introduce ice_vlan struct

Add a new struct for VLAN related information. Currently this holds
VLAN ID and priority values, but will be expanded to hold TPID value.
This reduces the changes necessary if any other values are added in
future. Remove the action argument from these calls as it's always
ICE_FWD_VSI.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: improve switchdev's slow-path

In current switchdev implementation, every VF PR is assigned to
individual ring on switchdev ctrl VSI. For slow-path traffic, there
is a mapping VF->ring done in software based on src_vsi value (by
calling ice_eswitch_get_target_netdev function).

With this change, HW solution is introduced which is more
efficient. For each VF, src MAC (VF's MAC) filter will be created,
which forwards packets to the corresponding switchdev ctrl VSI queue
based on src MAC address.

This filter has to be removed and then replayed in case of
resetting one VF. Keep information about this rule in repr->mac_rule,
thanks to that we know which rule has to be removed and replayed
for a given VF.

In case of CORE/GLOBAL all rules are removed
automatically. We have to take care of readding them. This is done
by ice_replay_vsi_adv_rule.

When driver leaves switchdev mode, remove all advanced rules
from switchdev ctrl VSI. This is done by ice_rem_adv_rule_for_vsi.

Flag repr->rule_added is needed because in some cases reset
might be triggered before VF sends request to add MAC.

Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Cleanup after ice_status removal

Clean up code after changing ice_status to int. Rearrange to fix reverse
Christmas tree and pull lines up where applicable.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>

ice: Remove enum ice_status

Replace uses of ice_status to, as equivalent as possible, error codes.
Remove enum ice_status and its helper conversion function as they are no
longer needed.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>

ice: Use int for ice_status

To prepare for removal of ice_status, change the variables from
ice_status to int. This eases the transition when values are changed to
return standard int error codes over enum ice_status.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>

ice: Refactor promiscuous functions

Some of the promiscuous mode functions take a boolean to indicate
set/clear, which affects readability. Refactor and provide an
interface for the promiscuous mode code with explicit set and clear
promiscuous mode operations.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Manage act flags for switchdev offloads

Currently it is not possible to set/unset lb_en and lan_en flags
for advanced rules during their creation. Both flags are enabled
by default. In case of switchdev offloads for egress traffic we
need lb_en to be disabled. Because of that, we work around it by
updating the rule immediately after its creation.

This change allows us to set/unset those flags right away and it
gets rid of old workaround as well. Using ice_adv_rule_flags_info
structure we can pass info about flags we want to be set for
a given advanced rule. Flags are stored in flags_info.act.
Values from act would be used only if act_valid was set to true,
otherwise default values would be used.

Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: Allow changing lan_en and lb_en on all kinds of filters

There is no way to change default lan_en and lb_en flags while
adding new rule. Add function that allows changing these flags
on rule determined by rule id and recipe id.

Function checks if the rule is presented on regular rules list or
advance rules list and call the appropriate function to update
rule entry.

As rules with ICE_SW_LKUP_DFLT recipe aren't tracked in a list,
implement function which updates flags without searching for rules
based only on rule id.

Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: allow changing lan_en and lb_en on dflt rules

There is no way to change default lan_en and lb_en flags while
adding new rule. Add function that allows changing these flags
on ICE_SW_LKUP_DFLT recipe and any rule id.

lan_en allows packet to go outside if rule is matched. Clearing
this bit will block packet from sending it outside.

lb_en allows packet to be forwarded to other VSI. Clearing
this bit will block packet from forwarding it to other VSI.

Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: refactor filter functions

Move filter functions to separate file.

Add functions that prepare suitable ice_fltr_info struct
depending on the filter type and add this struct to earlier created
list:
- ice_fltr_add_mac_to_list
- ice_fltr_add_vlan_to_list
- ice_fltr_add_eth_to_list
This functions are used in adding and removing filters.

Create wrappers for functions mentioned above that alloc list,
add suitable ice_fltr_info to it and call add or remove function.
- ice_fltr_prepare_mac
- ice_fltr_prepare_mac_and_broadcast
- ice_fltr_prepare_vlan
- ice_fltr_prepare_eth

Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>