iavf: enable symmetric-xor RSS for Toeplitz hash function

Allow the user to set the symmetric Toeplitz hash function via:

# ethtool -X eth0 hfunc toeplitz symmetric-xor

The driver will reject any new RSS configuration if a field other than
(IP src/dst and L4 src/dst ports) is requested for hashing.

The symmetric RSS will not be supported on PFs not advertising the ADV RSS
Offload flag (ADV_RSS_SUPPORT()), for example the E700 series (i40e).

Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-9-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

iavf: Introduce new state machines for flow director

New states introduced:

IAVF_FDIR_FLTR_DIS_REQUEST
IAVF_FDIR_FLTR_DIS_PENDING
IAVF_FDIR_FLTR_INACTIVE

Current FDIR state machines (SM) are not adequate to handle a few
scenarios in the link DOWN/UP event, reset event and ntuple-feature.

For example, when VF link goes DOWN and comes back UP administratively,
the expectation is that previously installed filters should also be
restored. But with current SM, filters are not restored.
So with new SM, during link DOWN filters are marked as INACTIVE in
the iavf list but removed from PF. After link UP, SM will transition
from INACTIVE to ADD_REQUEST to restore the filter.

Similarly, with VF reset, filters will be removed from the PF, but
marked as INACTIVE in the iavf list. Filters will be restored after
reset completion.

Steps to reproduce:
-------------------

1. Create a VF. Here VF is enp8s0.

2. Assign IP addresses to VF and link partner and ping continuously
from remote. Here remote IP is 1.1.1.1.

3. Check default RX Queue of traffic.

ethtool -S enp8s0 | grep -E "rx-[[:digit:]]+\.packets"

4. Add filter - change default RX Queue (to 15 here)

ethtool -U ens8s0 flow-type ip4 src-ip 1.1.1.1 action 15 loc 5

5. Ensure filter gets added and traffic is received on RX queue 15 now.

Link event testing:
-------------------
6. Bring VF link down and up. If traffic flows to configured queue 15,
test is success, otherwise it is a failure.

Reset event testing:
--------------------
7. Reset the VF. If traffic flows to configured queue 15, test is success,
otherwise it is a failure.

Fixes: 0dbfbabb840d ("iavf: Add framework to enable ethtool ntuple filters")
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Ranganatha Rao <ranganatha.rao@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: delete the iavf client interface

The iavf client interface was added in 2017 by commit ed0e894de7c1
("i40evf: add client interface"), but there have never been any in-tree
callers.

It's not useful for future development either. The Intel out-of-tree
iavf and irdma drivers instead use an auxiliary bus, which is a better
solution.

Remove the iavf client interface code. Also gone are the client_task
work and the client_lock mutex.

Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231027175941.1340255-9-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

intel: fix string truncation warnings

Fix -Wformat-truncated warnings to complete the intel directories' W=1
clean efforts. The W=1 recently got enhanced with a few new flags and
this brought up some new warnings.

Switch to using kasprintf() when possible so we always allocate the
right length strings.

summary of warnings:
drivers/net/ethernet/intel/iavf/iavf_virtchnl.c:1425:60: warning: ‘%s’ directive output may be truncated writing 4 bytes into a region of size between 1 and 11 [-Wformat-truncation=]
drivers/net/ethernet/intel/iavf/iavf_virtchnl.c:1425:17: note: ‘snprintf’ output between 7 and 17 bytes into a destination of size 13
drivers/net/ethernet/intel/ice/ice_ptp.c:43:27: warning: ‘%s’ directive output may be truncated writing up to 479 bytes into a region of size 64 [-Wformat-truncation=]
drivers/net/ethernet/intel/ice/ice_ptp.c:42:17: note: ‘snprintf’ output between 1 and 480 bytes into a destination of size 64
drivers/net/ethernet/intel/igb/igb_main.c:3092:53: warning: ‘%d’ directive output may be truncated writing between 1 and 5 bytes into a region of size between 1 and 13 [-Wformat-truncation=]
drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note: directive argument in the range [0, 65535]
drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note: directive argument in the range [0, 65535]
drivers/net/ethernet/intel/igb/igb_main.c:3090:25: note: ‘snprintf’ output between 23 and 43 bytes into a destination of size 32

Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231017190411.2199743-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

iavf: Add ability to turn off CRC stripping for VF

Previously CRC stripping was always enabled for VF.

Now it is possible to turn off CRC stripping via ethtool:

#ethtool -K <interface> rx-fcs on

To turn off CRC stripping, first VLAN stripping must be disabled:

#ethtool -K <interface> rx-vlan-offload off

if any VLAN interfaces exists, otherwise VLAN stripping will be turned
off by the driver.

In iavf_configure_queues add check if CRC stripping is enabled for
VF, if it's enabled then set crc_disabled to false on every VF's
queue. In iavf_set_features add check if CRC stripping setting was
changed then schedule reset.

Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Fix promiscuous mode configuration flow messages

Currently when configuring promiscuous mode on the AVF we detect a
change in the netdev->flags. We use IFF_PROMISC and IFF_ALLMULTI to
determine whether or not we need to request/release promiscuous mode
and/or multicast promiscuous mode. The problem is that the AQ calls for
setting/clearing promiscuous/multicast mode are treated separately. This
leads to a case where we can trigger two promiscuous mode AQ calls in
a row with the incorrect state. To fix this make a few changes.

Use IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE instead of the previous
IAVF_FLAG_AQ_[REQUEST|RELEASE]_[PROMISC|ALLMULTI] flags.

In iavf_set_rx_mode() detect if there is a change in the
netdev->flags in comparison with adapter->flags and set the
IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE aq_required bit. Then in
iavf_process_aq_command() only check for IAVF_FLAG_CONFIGURE_PROMISC_MODE
and call iavf_set_promiscuous() if it's set.

In iavf_set_promiscuous() check again to see which (if any) promiscuous
mode bits have changed when comparing the netdev->flags with the
adapter->flags. Use this to set the flags which get sent to the PF
driver.

Add a spinlock that is used for updating current_netdev_promisc_flags
and only allows one promiscuous mode AQ at a time.

[1] Fixes the fact that we will only have one AQ call in the aq_required
queue at any one time.

[2] Streamlines the change in promiscuous mode to only set one AQ
required bit.

[3] This allows us to keep track of the current state of the flags and
also makes it so we can take the most recent netdev->flags promiscuous
mode state.

[4] This fixes the problem where a change in the netdev->flags can cause
IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE to be set in iavf_set_rx_mode(),
but cleared in iavf_set_promiscuous() before the change is ever made via
AQ call.

Fixes: 47d3483988f6 ("i40evf: Add driver support for promiscuous mode")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

virtchnl: fix fake 1-elem arrays for structures allocated as `nents`

Finally, fix 3 structures which are allocated technically correctly,
i.e. the calculated size equals to the one that struct_size() would
return, except for sizeof(). For &virtchnl_vlan_filter_list_v2, use
the same approach when there are no enough space as taken previously
for &virtchnl_vlan_filter_list, i.e. let the maximum size be calculated
automatically instead of trying to guestimate it using maths.

Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

virtchnl: fix fake 1-elem arrays in structures allocated as `nents + 1`

There are five virtchnl structures, which are allocated and checked in
the code as `nents + 1`, meaning that they always have memory for one
excessive element regardless of their actual number. This comes from
that their sizeof() includes space for 1 element and then they get
allocated via struct_size() or its open-coded equivalents, passing
the actual number of elements.
Expand virtchnl_struct_size() to handle such structures and replace
those 1-elem arrays with proper flex ones. Also fix several places
which open-code %IAVF_VIRTCHNL_VF_RESOURCE_SIZE. Finally, let the
virtchnl_ether_addr_list size be computed automatically when there's
no enough space for the whole list, otherwise we have to open-code
reverse struct_size() logics.

Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

virtchnl: fix fake 1-elem arrays in structs allocated as `nents + 1` - 1

The two most problematic virtchnl structures are virtchnl_rss_key and
virtchnl_rss_lut. Their "flex" arrays have the type of u8, thus, when
allocating / checking, the actual size is calculated as `sizeof +
nents - 1 byte`. But their sizeof() is not 1 byte larger than the size
of such structure with proper flex array, it's two bytes larger due to
the padding. That said, their size is always 1 byte larger unless
there are no tail elements -- then it's +2 bytes.
Add virtchnl_struct_size() macro which will handle this case (and later
other cases as well). Make its calling conv the same as we call
struct_size() to allow it to be drop-in, even though it's unlikely to
become possible to switch to generic API. The macro will calculate a
proper size of a structure with a flex array at the end, so that it
becomes transparent for the compilers, but add the difference from the
old values, so that the real size of sorta-ABI-messages doesn't change.
Use it on the allocation side in IAVF and the receiving side (defined
as static inline in virtchnl.h) for the mentioned two structures.

Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: fix reset task race with iavf_remove()

The reset task is currently scheduled from the watchdog or adminq tasks.
First, all direct calls to schedule the reset task are replaced with the
iavf_schedule_reset(), which is modified to accept the flag showing the
type of reset.

To prevent the reset task from starting once iavf_remove() starts, we need
to check the __IAVF_IN_REMOVE_TASK bit before we schedule it. This is now
easily added to iavf_schedule_reset().

Finally, remove the check for IAVF_FLAG_RESET_NEEDED in the watchdog task.
It is redundant since all callers who set the flag immediately schedules
the reset task.

Fixes: 3ccd54ef44eb ("iavf: Fix init state closure on remove")
Fixes: 14756b2ae265 ("iavf: Fix __IAVF_RESETTING state usage")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: fix a deadlock caused by rtnl and driver's lock circular dependencies

A driver's lock (crit_lock) is used to serialize all the driver's tasks.
Lockdep, however, shows a circular dependency between rtnl and
crit_lock. This happens when an ndo that already holds the rtnl requests
the driver to reset, since the reset task (in some paths) tries to grab
rtnl to either change real number of queues of update netdev features.

[566.241851] ======================================================
[566.241893] WARNING: possible circular locking dependency detected
[566.241936] 6.2.14-100.fc36.x86_64+debug #1 Tainted: G OE
[566.241984] ------------------------------------------------------
[566.242025] repro.sh/2604 is trying to acquire lock:
[566.242061] ffff9280fc5ceee8 (&adapter->crit_lock){+.+.}-{3:3}, at: iavf_close+0x3c/0x240 [iavf]
[566.242167]
but task is already holding lock:
[566.242209] ffffffff9976d350 (rtnl_mutex){+.+.}-{3:3}, at: iavf_remove+0x6b5/0x730 [iavf]
[566.242300]
which lock already depends on the new lock.

[566.242353]
the existing dependency chain (in reverse order) is:
[566.242401]
-> #1 (rtnl_mutex){+.+.}-{3:3}:
[566.242451] __mutex_lock+0xc1/0xbb0
[566.242489] iavf_init_interrupt_scheme+0x179/0x440 [iavf]
[566.242560] iavf_watchdog_task+0x80b/0x1400 [iavf]
[566.242627] process_one_work+0x2b3/0x560
[566.242663] worker_thread+0x4f/0x3a0
[566.242696] kthread+0xf2/0x120
[566.242730] ret_from_fork+0x29/0x50
[566.242763]
-> #0 (&adapter->crit_lock){+.+.}-{3:3}:
[566.242815] __lock_acquire+0x15ff/0x22b0
[566.242869] lock_acquire+0xd2/0x2c0
[566.242901] __mutex_lock+0xc1/0xbb0
[566.242934] iavf_close+0x3c/0x240 [iavf]
[566.242997] __dev_close_many+0xac/0x120
[566.243036] dev_close_many+0x8b/0x140
[566.243071] unregister_netdevice_many_notify+0x165/0x7c0
[566.243116] unregister_netdevice_queue+0xd3/0x110
[566.243157] iavf_remove+0x6c1/0x730 [iavf]
[566.243217] pci_device_remove+0x33/0xa0
[566.243257] device_release_driver_internal+0x1bc/0x240
[566.243299] pci_stop_bus_device+0x6c/0x90
[566.243338] pci_stop_and_remove_bus_device+0xe/0x20
[566.243380] pci_iov_remove_virtfn+0xd1/0x130
[566.243417] sriov_disable+0x34/0xe0
[566.243448] ice_free_vfs+0x2da/0x330 [ice]
[566.244383] ice_sriov_configure+0x88/0xad0 [ice]
[566.245353] sriov_numvfs_store+0xde/0x1d0
[566.246156] kernfs_fop_write_iter+0x15e/0x210
[566.246921] vfs_write+0x288/0x530
[566.247671] ksys_write+0x74/0xf0
[566.248408] do_syscall_64+0x58/0x80
[566.249145] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[566.249886]
other info that might help us debug this:

[566.252014] Possible unsafe locking scenario:

[566.253432] CPU0 CPU1
[566.254118] ---- ----
[566.254800] lock(rtnl_mutex);
[566.255514] lock(&adapter->crit_lock);
[566.256233] lock(rtnl_mutex);
[566.256897] lock(&adapter->crit_lock);
[566.257388]
*** DEADLOCK ***

The deadlock can be triggered by a script that is continuously resetting
the VF adapter while doing other operations requiring RTNL, e.g:

while :; do
ip link set $VF up
ethtool --set-channels $VF combined 2
ip link set $VF down
ip link set $VF up
ethtool --set-channels $VF combined 4
ip link set $VF down
done

Any operation that triggers a reset can substitute "ethtool --set-channles"

As a fix, add a new task "finish_config" that do all the work which
needs rtnl lock. With the exception of iavf_remove(), all work that
require rtnl should be called from this task.

As for iavf_remove(), at the point where we need to call
unregister_netdevice() (and grab rtnl_lock), we make sure the finish_config
task is not running (cancel_work_sync()) to safely grab rtnl. Subsequent
finish_config work cannot restart after that since the task is guarded
by the __IAVF_IN_REMOVE_TASK bit in iavf_schedule_finish_config().

Fixes: 5ac49f3c2702 ("iavf: use mutexes for locking of critical sections")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Wait for reset in callbacks which trigger it

There was a fail when trying to add the interface to bonding
right after changing the MTU on the interface. It was caused
by bonding interface unable to open the interface due to
interface being in __RESETTING state because of MTU change.

Add new reset_waitqueue to indicate that reset has finished.

Add waiting for reset to finish in callbacks which trigger hw reset:
iavf_set_priv_flags(), iavf_change_mtu() and iavf_set_ringparam().
We use a 5000ms timeout period because on Hyper-V based systems,
this operation takes around 3000-4000ms. In normal circumstances,
it doesn't take more than 500ms to complete.

Add a function iavf_wait_for_reset() to reuse waiting for reset code and
use it also in iavf_set_channels(), which already waits for reset.
We don't use error handling in iavf_set_channels() as this could
cause the device to be in incorrect state if the reset was scheduled
but hit timeout or the waitng function was interrupted by a signal.

Fixes: 4e5e6b5d9d13 ("iavf: Fix return of set the new channel count")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Co-developed-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: send VLAN offloading caps once after VFR

When the user disables rxvlan offloading and then changes the number of
channels, all VLAN ports are unable to receive traffic.

Changing the number of channels triggers a VFR reset. During re-init, when
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is received, we do:
1 - set the IAVF_FLAG_SETUP_NETDEV_FEATURES flag
2 - call
iavf_set_vlan_offload_features(adapter, 0, netdev->features);

The second step sends to the PF the __default__ features, in this case
aq_required |= IAVF_FLAG_AQ_ENABLE_CTAG_VLAN_STRIPPING

While the first step forces the watchdog task to call
netdev_update_features() -> iavf_set_features() ->
iavf_set_vlan_offload_features(adapter, netdev->features, features).
Since the user disabled the "rxvlan", this sets:
aq_required |= IAVF_FLAG_AQ_DISABLE_CTAG_VLAN_STRIPPING

When we start processing the AQ commands, both flags are enabled. Since we
process DISABLE_XTAG first then ENABLE_XTAG, this results in the PF
enabling the rxvlan offload. This breaks all communications on the VLAN
net devices.

Fix by removing the call to iavf_set_vlan_offload_features() (second
step). Calling netdev_update_features() from watchdog task is enough for
both init and reset paths.

Fixes: 7598f4b40bd6 ("iavf: Move netdev_update_features() into watchdog task")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: remove active_cvlans and active_svlans bitmaps

The VLAN filters info is currently being held in a list and 2 bitmaps
(active_cvlans and active_svlans). We are experiencing some racing where
data is not in sync in the list and bitmaps. For example, the VLAN is
initially added to the list but only when the PF replies, it is added to
the bitmap. If a user adds many V2 VLANS before the PF responds:

while [ $((i++)) ]
ip l add l eth0 name eth0.$i type vlan id $i

we might end up with more VLAN list entries than the designated limit.
Also, The "ip link show" will show more links added than the PF limit.

On the other and, the bitmaps are only used to check the number of VLAN
filters and to re-enable the filters when the interface goes from DOWN to
UP.

This patch gets rid of the bitmaps and uses the list only. To do that,
the states of the VLAN filter are modified:
1 - IAVF_VLAN_REMOVE: the entry needs to be totally removed after informing
the PF. This is the "ip link del eth0.$i" path.
2 - IAVF_VLAN_DISABLE: (new) the netdev went down. The filter needs to be
removed from the PF and then marked INACTIVE.
3 - IAVF_VLAN_INACTIVE: (new) no PF filter exists, but the user did not
delete the VLAN.

Fixes: 48ccc43ecf10 ("iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: refactor VLAN filter states

The VLAN filter states are currently being saved as individual bits.
This is error prone as multiple bits might be mistakenly set.

Fix by replacing the bits with a single state enum. Also, add an
"ACTIVE" state for filters that are accepted by the PF.

Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: do not track VLAN 0 filters

When an interface with the maximum number of VLAN filters is brought up,
a spurious error is logged:

[257.483082] 8021q: adding VLAN 0 to HW filter on device enp0s3
[257.483094] iavf 0000:00:03.0 enp0s3: Max allowed VLAN filters 8. Remove existing VLANs or disable filtering via Ethtool if supported.

The VF driver complains that it cannot add the VLAN 0 filter.

On the other hand, the PF driver always adds VLAN 0 filter on VF
initialization. The VF does not need to ask the PF for that filter at
all.

Fix the error by not tracking VLAN 0 filters altogether. With that, the
check added by commit 0e710a3ffd0c ("iavf: Fix VF driver counting VLAN 0
filters") in iavf_virtchnl.c is useless and might be confusing if left as
it suggests that we track VLAN 0.

Fixes: 0e710a3ffd0c ("iavf: Fix VF driver counting VLAN 0 filters")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

virtchnl: i40e/iavf: rename iwarp to rdma

Since the latest Intel hardware does both IWARP and ROCE, rename the
term IWARP in the virtchnl header to be RDMA. Do this for both upper and
lower case instances. Many of the non-virtchnl.h changes were done with
regular expression replacements using perl like:
perl -p -i -e 's/_IWARP/_RDMA/' <files>
perl -p -i -e 's/_iwarp/_rdma/' <files>
and I had to pick up a few instances manually.

The virtchnl.h header has some comments and clarity added around when to
use certain defines.

note: had to fix a checkpatch warning for a long line by wrapping one of
the lines I changed.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jakub Andrysiak <jakub.andrysiak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Move netdev_update_features() into watchdog task

Remove netdev_update_features() from iavf_adminq_task(), as it can cause
deadlocks due to needing rtnl_lock. Instead use the
IAVF_FLAG_SETUP_NETDEV_FEATURES flag to indicate that netdev features need
to be updated in the watchdog task. iavf_set_vlan_offload_features()
and iavf_set_queue_vlan_tag_loc() can be called directly from
iavf_virtchnl_completion().

Suggested-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: fix temporary deadlock and failure to set MAC address

We are seeing an issue where setting the MAC address on iavf fails with
EAGAIN after the 2.5s timeout expires in iavf_set_mac().

There is the following deadlock scenario:

iavf_set_mac(), holding rtnl_lock, waits on:
iavf_watchdog_task (within iavf_wq) to send a message to the PF,
and
iavf_adminq_task (within iavf_wq) to receive a response from the PF.
In this adapter state (>=__IAVF_DOWN), these tasks do not need to take
rtnl_lock, but iavf_wq is a global single-threaded workqueue, so they
may get stuck waiting for another adapter's iavf_watchdog_task to run
iavf_init_config_adapter(), which does take rtnl_lock.

The deadlock resolves itself by the timeout in iavf_set_mac(),
which results in EAGAIN returned to userspace.

Let's break the deadlock loop by changing iavf_wq into a per-adapter
workqueue, so that one adapter's tasks are not blocked by another's.

Fixes: 35a2443d0910 ("iavf: Add waiting for response from PF in set mac")
Co-developed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Fix VF driver counting VLAN 0 filters

VF driver mistakenly counts VLAN 0 filters, when no PF driver
counts them.
Do not count VLAN 0 filters, when VLAN_V2 is engaged.
Counting those filters in, will affect filters size by -1, when
sending batched VLAN addition message.

Fixes: 968996c070ef ("iavf: Fix VLAN_V2 addition/rejection")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Fix set max MTU size with port VLAN and jumbo frames

After setting port VLAN and MTU to 9000 on VF with ice driver there
was an iavf error
"PF returned error -5 (IAVF_ERR_PARAM) to our request 6".

During queue configuration, VF's max packet size was set to
IAVF_MAX_RXBUFFER but on ice max frame size was smaller by VLAN_HLEN
due to making some space for port VLAN as VF is not aware whether it's
in a port VLAN. This mismatch in sizes caused ice to reject queue
configuration with ERR_PARAM error. Proper max_mtu is sent from ice PF
to VF with GET_VF_RESOURCES msg but VF does not look at this.

In iavf change max_frame from IAVF_MAX_RXBUFFER to max_mtu
received from pf with GET_VF_RESOURCES msg to make vf's
max_frame_size dependent from pf. Add check if received max_mtu is
not in eligible range then set it to IAVF_MAX_RXBUFFER.

Fixes: dab86afdbbd1 ("i40e/i40evf: Change the way we limit the maximum frame size for Rx")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

intel: remove unused macros

As found by the compile option -Wunused-macros, remove these macros
that are never used by the code.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Add waiting for response from PF in set mac

Make iavf_set_mac synchronous by waiting for a response
from a PF. Without this iavf_set_mac is always returning
success even though set_mac can be rejected by a PF.
This ensures that when set_mac exits netdev MAC is updated.
This is needed for sending ARPs with correct MAC after
changing VF's MAC. This is also needed by bonding module.

Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Fix VLAN_V2 addition/rejection

Fix VLAN addition, so that PF driver does not reject whole VLAN batch.
Add VLAN reject handling, so rejected VLANs, won't litter VLAN filter
list. Fix handling of active_(c/s)vlans, so it will be possible to
re-add VLAN filters for user.
Without this patch, after changing trust to off, with VLAN filters
saturated, no VLAN is added, due to PF rejecting addition.

Fixes: 92fc50859872 ("iavf: Restrict maximum VLAN filters for VIRTCHNL_VF_OFFLOAD_VLAN_V2")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Fix incorrect use of assigning iavf_status to int

Currently there are functions in iavf_virtchnl.c for polling specific
virtchnl receive events. These are all assigning iavf_status values to
int values. Fix this and explicitly assign int values if iavf_status
is not IAVF_SUCCESS.

Also, refactor a small amount of duplicated code that can be reused by
all of the previously mentioned functions.

Finally, fix some spacing errors for variable assignment and get rid of
all the goto statements in the refactored functions for clarity.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: stop leaking iavf_status as "errno" values

Several functions in the iAVF core files take status values of the enum
iavf_status and convert them into integer values. This leads to
confusion as functions return both Linux errno values and status codes
intermixed. Reporting status codes as if they were "errno" values can
lead to confusion when reviewing error logs. Additionally, it can lead
to unexpected behavior if a return value is not interpreted properly.

Fix this by introducing iavf_status_to_errno, a switch that explicitly
converts from the status codes into an appropriate error value. Also
introduce a virtchnl_status_to_errno function for the one case where we
were returning both virtchnl status codes and iavf_status codes in the
same function.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Add usage of new virtchnl format to set default MAC

Use new type field of VIRTCHNL_OP_ADD_ETH_ADDR and
VIRTCHNL_OP_DEL_ETH_ADDR requests to indicate that
VF wants to change its default MAC address.

Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Fix handling of vlan strip virtual channel messages

Modify netdev->features for vlan stripping based on virtual
channel messages received from the PF. Change is needed
to synchronize vlan strip status between PF sysfs and iavf ethtool.

Fixes: 5951a2b9812d ("iavf: Fix VLAN feature flags after VFR")
Signed-off-by: Norbert Ciosek <norbertx.ciosek@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Fix locking for VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS

iavf_virtchnl_completion is called under crit_lock but when
the code for VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is called,
this lock is released in order to obtain rtnl_lock to avoid
ABBA deadlock with unregister_netdev.

Along with the new way iavf_remove behaves, there exist
many risks related to the lock release and attmepts to regrab
it. The driver faces crashes related to races between
unregister_netdev and netdev_update_features. Yet another
risk is that the driver could already obtain the crit_lock
in order to destroy it and iavf_virtchnl_completion could
crash or block forever.

Make iavf_virtchnl_completion never relock crit_lock in it's
call paths.

Extract rtnl_lock locking logic to the driver for
unregister_netdev in order to set the netdev_registered flag
inside the lock.

Introduce a new flag that will inform adminq_task to perform
the code from VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS right after
it finishes processing messages. Guard this code with remove
flags so it's never called when the driver is in remove state.

Fixes: 5951a2b9812d ("iavf: Fix VLAN feature flags after VFR")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 offload enable/disable

The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows
the VF to support 802.1Q and 802.1ad VLAN insertion and stripping if
successfully negotiated via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS.
Multiple changes were needed to support this new functionality.

1. Added new aq_required flags to support any kind of VLAN stripping and
insertion offload requests via virtchnl.

2. Added the new method iavf_set_vlan_offload_features() that's
used during VF initialization, VF reset, and iavf_set_features() to
set the aq_required bits based on the current VLAN offload
configuration of the VF's netdev.

3. Added virtchnl handling for VIRTCHNL_OP_ENABLE_STRIPPING_V2,
VIRTCHNL_OP_DISABLE_STRIPPING_V2, VIRTCHNL_OP_ENABLE_INSERTION_V2,
and VIRTCHNL_OP_ENABLE_INSERTION_V2.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 hotpath

The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows
the PF to set the location of the Tx and Rx VLAN tag for insertion and
stripping offloads. In order to support this functionality a few changes
are needed.

1. Add a new method to cache the VLAN tag location based on negotiated
capabilities for the Tx and Rx ring flags. This needs to be called in
the initialization and reset paths.

2. Refactor the transmit hotpath to account for the new Tx ring flags.
When IAVF_TXR_FLAGS_VLAN_LOC_L2TAG2 is set, then the driver needs to
insert the VLAN tag in the L2TAG2 field of the transmit descriptor.
When the IAVF_TXRX_FLAGS_VLAN_LOC_L2TAG1 is set, then the driver needs
to use the l2tag1 field of the data descriptor (same behavior as
before).

3. Refactor the iavf_tx_prepare_vlan_flags() function to simplify
transmit hardware VLAN offload functionality by only depending on the
skb_vlan_tag_present() function. This can be done because the OS
won't request transmit offload for a VLAN unless the driver told the
OS it's supported and enabled.

4. Refactor the receive hotpath to account for the new Rx ring flags and
VLAN ethertypes. This requires checking the Rx ring flags and
descriptor status bits to determine the location of the VLAN tag.
Also, since only a single ethertype can be supported at a time, check
the enabled netdev features before specifying a VLAN ethertype in
__vlan_hwaccel_put_tag().

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config

Based on VIRTCHNL_VF_OFFLOAD_VLAN_V2, the VF can now support more VLAN
capabilities (i.e. 802.1AD offloads and filtering). In order to
communicate these capabilities to the netdev layer, the VF needs to
parse its VLAN capabilities based on whether it was able to negotiation
VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or neither of
these.

In order to support this, add the following functionality:

iavf_get_netdev_vlan_hw_features() - This is used to determine the VLAN
features that the underlying hardware supports and that can be toggled
off/on based on the negotiated capabiltiies. For example, if
VIRTCHNL_VF_OFFLOAD_VLAN_V2 was negotiated, then any capability marked
with VIRTCHNL_VLAN_TOGGLE can be toggled on/off by the VF. If
VIRTCHNL_VF_OFFLOAD_VLAN was negotiated, then only VLAN insertion and/or
stripping can be toggled on/off.

iavf_get_netdev_vlan_features() - This is used to determine the VLAN
features that the underlying hardware supports and that should be
enabled by default. For example, if VIRTHCNL_VF_OFFLOAD_VLAN_V2 was
negotiated, then any supported capability that has its ethertype_init
filed set should be enabled by default. If VIRTCHNL_VF_OFFLOAD_VLAN was
negotiated, then filtering, stripping, and insertion should be enabled
by default.

Also, refactor iavf_fix_features() to take into account the new
capabilities. To do this, query all the supported features (enabled by
default and toggleable) and make sure the requested change is supported.
If VIRTCHNL_VF_OFFLOAD_VLAN_V2 is successfully negotiated, there is no
need to check VIRTCHNL_VLAN_TOGGLE here because the driver already told
the netdev layer which features can be toggled via netdev->hw_features
during iavf_process_config(), so only those features will be requested
to change.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 negotiation

In order to support the new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability the
VF driver needs to rework it's initialization state machine and reset
flow. This has to be done because successful negotiation of
VIRTCHNL_VF_OFFLOAD_VLAN_V2 requires the VF driver to perform a second
capability request via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS before
configuring the adapter and its netdev.

Add the VIRTCHNL_VF_OFFLOAD_VLAN_V2 bit when sending the
VIRTHCNL_OP_GET_VF_RESOURECES message. The underlying PF will either
support VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or
neither. Both of these offloads should never be supported together.

Based on this, add 2 new states to the initialization state machine:

__IAVF_INIT_GET_OFFLOAD_VLAN_V2_CAPS
__IAVF_INIT_CONFIG_ADAPTER

The __IAVF_INIT_GET_OFFLOAD_VLAN_V2_CAPS state is used to request/store
the new VLAN capabilities if and only if VIRTCHNL_VLAN_OFFLOAD_VLAN_V2
was successfully negotiated in the __IAVF_INIT_GET_RESOURCES state.

The __IAVF_INIT_CONFIG_ADAPTER state is used to configure the
adapter/netdev after the resource requests have finished. The VF will
move into this state regardless of whether it successfully negotiated
VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2.

Also, add a the new flag IAVF_FLAG_AQ_GET_OFFLOAD_VLAN_V2_CAPS and set
it during VF reset. If VIRTCHNL_VF_OFFLOAD_VLAN_V2 was successfully
negotiated then the VF will request its VLAN capabilities via
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS during the reset. This is needed
because the PF may change/modify the VF's configuration during VF reset
(i.e. modifying the VF's port VLAN configuration).

This also, required the VF to call netdev_update_features() since its
VLAN features may change during VF reset. Make sure to call this under
rtnl_lock().

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Refactor string format to avoid static analysis warnings

Change format to match variable type that is used in string.

Use %u format for unsigned variable and %d format for signed variable
to remove static analysis warnings.

Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Refactor text of informational message

This message is intended to be informational to indicate a reset is about
to happen, but the use of "warning" in the message text can cause concern
with users. Reword the message to make it less alarming.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Log info when VF is entering and leaving Allmulti mode

Add log when VF is entering and leaving Allmulti mode.
The change of VF state is visible in dmesg now.
Without this commit, entering and leaving Allmulti mode
is not logged in dmesg.

Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Fix VLAN feature flags after VFR

When a VF goes through a reset, it's possible for the VF's feature set
to change. For example it may lose the VIRTCHNL_VF_OFFLOAD_VLAN
capability after VF reset. Unfortunately, the driver doesn't correctly
deal with this situation and errors are seen from downing/upping the
interface and/or moving the interface in/out of a network namespace.

When setting the interface down/up we see the following errors after the
VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from the VF:

ice 0000:51:00.1: VF 1 failed opcode 12, retval: -64 iavf 0000:51:09.1:
Failed to add VLAN filter, error IAVF_NOT_SUPPORTED ice 0000:51:00.1: VF
1 failed opcode 13, retval: -64 iavf 0000:51:09.1: Failed to delete VLAN
filter, error IAVF_NOT_SUPPORTED

These add/delete errors are happening because the VLAN filters are
tracked internally to the driver and regardless of the VLAN_ALLOWED()
setting the driver tries to delete/re-add them over virtchnl.

Fix the delete failure by making sure to delete any VLAN filter tracking
in the driver when a removal request is made, while preventing the
virtchnl request. This makes it so the driver's VLAN list is up to date
and the errors are

Fix the add failure by making sure the check for VLAN_ALLOWED() during
reset is done after the VF receives its capability list from the PF via
VIRTCHNL_OP_GET_VF_RESOURCES. If VLAN functionality is not allowed, then
prevent requesting re-adding the filters over virtchnl.

When moving the interface into a network namespace we see the following
errors after the VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from
the VF:

iavf 0000:51:09.1 enp81s0f1v1: NIC Link is Up Speed is 25 Gbps Full Duplex
iavf 0000:51:09.1 temp_27: renamed from enp81s0f1v1
iavf 0000:51:09.1 mgmt: renamed from temp_27
iavf 0000:51:09.1 dev27: set_features() failed (-22); wanted 0x020190001fd54833, left 0x020190001fd54bb3

These errors are happening because we aren't correctly updating the
netdev capabilities and dealing with ndo_fix_features() and
ndo_set_features() correctly.

Fix this by only reporting errors in the driver's ndo_set_features()
callback when VIRTCHNL_VF_OFFLOAD_VLAN is not allowed and any attempt to
enable the VLAN features is made. Also, make sure to disable VLAN
insertion, filtering, and stripping since the VIRTCHNL_VF_OFFLOAD_VLAN
flag applies to all of them and not just VLAN stripping.

Also, after we process the capabilities in the VF reset path, make sure
to call netdev_update_features() in case the capabilities have changed
in order to update the netdev's feature set to match the VF's actual
capabilities.

Lastly, make sure to always report success on VLAN filter delete when
VIRTCHNL_VF_OFFLOAD_VLAN is not supported. The changed flow in
iavf_del_vlans() allows the stack to delete previosly existing VLAN
filters even if VLAN filtering is not allowed. This makes it so the VLAN
filter list is up to date.

Fixes: 8774370d268f ("i40e/i40evf: support for VF VLAN tag stripping control")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Fix refreshing iavf adapter stats on ethtool request

Currently iavf adapter statistics are refreshed only in a
watchdog task, triggered approximately every two seconds,
which causes some ethtool requests to return outdated values.

Add explicit statistics refresh when requested by ethtool -S.

Fixes: b476b0030e61 ("iavf: Move commands processing to the separate function")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Refactor iavf state machine tracking

Replace state changes of iavf state machine
with a method that also tracks the previous
state the machine was on.

This change is required for further work with
refactoring init and watchdog state machines.

Tracking of previous state would help us
recover iavf after failure has occurred.

Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ethernet: use eth_hw_addr_set() instead of ether_addr_copy()

Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():

@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

iavf: Fix ping is lost after untrusted VF had tried to change MAC

Make changes to MAC address dependent on the response of PF.
Disallow changes to HW MAC address and MAC filter from untrusted
VF, thanks to that ping is not lost if VF tries to change MAC.
Add a new field in iavf_mac_filter, to indicate whether there
was response from PF for given filter. Based on this field pass
or discard the filter.
If untrusted VF tried to change it's address, it's not changed.
Still filter was changed, because of that ping couldn't go through.

Fixes: c5c922b3e09b ("iavf: fix MAC address setting for VFs when filter is rejected")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <Gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

iavf: Support for modifying TCP RSS flow hashing

Provides the ability to enable TCP RSS hashing by ethtool.

It gives users option of generating RSS hash based on the TCP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.

Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Add framework to enable ethtool RSS config

Add the virtchnl message interface to VF, so that VF can request RSS
input set(s) based on PF's capability.

This framework allows ethtool RSS config support on the VF driver.

Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: add support for UDP Segmentation Offload

Add code to support UDP segmentation offload (USO) for
hardware that supports it.

Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

intel: clean up mismatched header comments

A bunch of header comments were showing warnings when compiling
with W=1. Fix them all at once. This changes only comments.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Support IPv4 Flow Director filters

Support the addition and deletion of IPv4 filters.

Supported fields are: src-ip, dst-ip, src-port, dst-port and l4proto
Supported flow-types are: tcp4, udp4, sctp4, ip4, ah4, esp4

Example usage:
ethtool -N ens787f0v0 flow-type tcp4 src-ip 192.168.0.20 \
dst-ip 192.168.0.21 tos 4 src-port 22 dst-port 23 action 8

L2TPv3 over IP with 'Session ID' 17:
ethtool -N ens787f0v0 flow-type ip4 l4proto 115 l4data 17 action 3

Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Add framework to enable ethtool ntuple filters

Enable ethtool ntuple filter support on the VF driver using the virtchnl
interface to the PF driver and the Flow director functionality in the
hardware.

Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: Use kzalloc for allocating only one thing

Use kzalloc rather than kcalloc(1,...)

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
@@

- kcalloc(1,
+ kzalloc(
...)
// </smpl>

Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

iavf: Fix reporting 2.5 Gb and 5Gb speeds

Commit 4ae4916b5643 ("i40e: fix 'Unknown bps' in dmesg for 2.5Gb/5Gb
speeds") added the ability for the PF to report 2.5 and 5Gb speeds,
however, the iavf driver does not recognize those speeds as the values were
not added there. Add the proper enums and values so that iavf can properly
deal with those speeds.

Fixes: 4ae4916b5643 ("i40e: fix 'Unknown bps' in dmesg for 2.5Gb/5Gb speeds")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Witold Fijalkowski <witoldx.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: use appropriate enum for comparison

adapter->link_speed has type enum virtchnl_link_speed but our comparisons
are against enum iavf_aq_link_speed. Though they are, currently, the same
values, change the comparison to the matching enum virtchnl_link_speed
since that may not always be the case.

Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: fix speed reporting over virtchnl

Link speeds are communicated over virtchnl using an enum
virtchnl_link_speed. Currently, the highest link speed is 40Gbps which
leaves us unable to reflect some speeds that an ice VF is capable of.
This causes link speed to be misreported on the iavf driver.

Allow for communicating link speeds using Mbps so that the proper speed can
be reported for an ice VF. Moving away from the enum allows us to
communicate future speed changes without requiring a new enum to be added.

In order to support communicating link speeds over virtchnl in Mbps the
following functionality was added:
- Added u32 link_speed_mbps in the iavf_adapter structure.
- Added the macro ADV_LINK_SUPPORT(_a) to determine if the VF
driver supports communicating link speeds in Mbps.
- Added the function iavf_get_vpe_link_status() to fill the
correct link_status in the event_data union based on the
ADV_LINK_SUPPORT(_a) macro.
- Added the function iavf_set_adapter_link_speed_from_vpe()
to determine whether or not to fill the u32 link_speed_mbps or
enum virtchnl_link_speed link_speed field in the iavf_adapter
structure based on the ADV_LINK_SUPPORT(_a) macro.
- Do not free vf_res in iavf_init_get_resources() as vf_res will be
accessed in iavf_get_link_ksettings(); memset to 0 instead. This
memory is subsequently freed in iavf_remove().

Fixes: 7c710869d64e ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: Enable support for up to 16 queues

Previous devices could only allocate 4 MSI-X vectors per VF so there was a
limitation of 4 queues. 800-series hardware can allocate more than 4 MSI-X
vectors, so expand the limitation on the number of queues that the driver
can support to account for these capabilities.

Fix ethtool channel operations to accommodate this change and adjust the
reporting of max number of queues to what is given to us by the PF. Since
we're not requesting queues above this value, just trigger reset to
activate the queues, which we already own.

Finally, fix a test condition that would display an incorrect error
message.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: remove current MAC address filter on VF reset

Currently MAC filters are not altered during a VF reset event. This may
lead to a stale filter when an administratively set MAC is forced by the
PF.

For an administratively set MAC the PF driver deletes the VFs filters,
overwrites the VFs MAC address and triggers a VF reset. However
the VF driver itself is not aware of the filter removal, which is what
the VF reset is for.
The VF reset queues all filters present in the VF driver to be re-added
to the PF filter list (including the filter for the now stale VF MAC
address) and triggers a VIRTCHNL_OP_GET_VF_RESOURCES event, which
provides the new MAC address to the VF.

When this happens i40e will complain and reject the stale MAC filter,
at least in the untrusted VF case.
i40e 0000:08:00.0: Setting MAC 3c:fa:fa:fa:fa:01 on VF 0
iavf 0000:08:02.0: Reset warning received from the PF
iavf 0000:08:02.0: Scheduling reset task
i40e 0000:08:00.0: Bring down and up the VF interface to make this change effective.
i40e 0000:08:00.0: VF attempting to override administratively set MAC address, bring down and up the VF interface to resume normal operation
i40e 0000:08:00.0: VF 0 failed opcode 10, retval: -1
iavf 0000:08:02.0: Failed to add MAC filter, error IAVF_ERR_NVM

To avoid re-adding the stale MAC filter it needs to be removed from the
VF driver's filter list before queuing the existing filters. Then during
the VIRTCHNL_OP_GET_VF_RESOURCES event the correct filter needs to be
added again, at which point the MAC address has been updated.

As a bonus this change makes bringing the VF down and up again
superfluous for the administratively set MAC case.

Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: fix MAC address setting for VFs when filter is rejected

Currently iavf unconditionally applies MAC address change requests. This
brings the VF in a state where it is no longer able to pass traffic if
the PF rejects a MAC filter change for the VF.
A typical scenario for a rejected MAC filter is for an untrusted VF to
request to change the MAC address when an administratively set MAC is
present.

To keep iavf working in this scenario the MAC filter handling in iavf
needs to act on the PF reply regarding the MAC filter change. In the
case of an ack the new MAC address gets set, whereas in the case of a
nack the previous MAC address needs to stay in place.

Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: use struct_size() helper

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, replace code of the following form:

sizeof(struct virtchnl_ether_addr_list) + (count * sizeof(struct virtchnl_ether_addr))

with:

struct_size(veal, list, count)

and so on...

This code was detected with the help of Coccinelle.

Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: Remove timer for work triggering, use delaying work instead

Remove the watchdog timer, instead declare watchdog task
as delayed work and use dedicated workqueue to service driver
tasks. The dedicated driver workqueue iavf_wq is common
for all driver instances.

Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: Fix the math for valid length for ADq enable

There was a calculation error in virtchnl regarding the valid
length which was fixed recently and a corresponding change needs
to go into the code while we enable ADq.

Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: update comments and file checks to match iavf

Some small things were missed with recent name changes
from i40e to iavf. Having a separate patch allows to
correct the small misses in one place.

Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: rename iavf_status structure flags

rename the flags inside of iavf_status from I40E_*
to IAVF_*

Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: replace i40e variables with iavf

Update the old variables and flags marked as i40e to match
the iavf name of the driver.

Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: change iavf_status_code to iavf_status

Instead of typedefing the enum iavf_status_code with iavf_status,
just shorten the enum itself and get rid of typedef.

Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: Limiting RSS queues to CPUs

Limiting RSS queues number to online CPUs number in order to
avoid issues with creating misconfigured RSS queues.

Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: finish renaming files to iavf

This finishes the process of renaming the files that
make sense to rename (skipping adminq related files that
talk to i40e), and fixes up the build and the #includes
so that everything builds nicely.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: rename most of i40e strings

This is the big rename patch, it takes most of the i40e_
and I40E_ strings and renames them to iavf_ and IAVF_.

Some of the adminq code, as well as most of the client
interface code used by RDMA is left unchanged in order
to indicate that the driver is talking to non-internal to
iavf code.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: rename i40e_hw to iavf_hw

Fix up the i40e_hw names to new name, including versions
inside other strings.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

iavf: move i40evf files to new name

Simply move the i40evf files to the new name, updating the #includes
to track the new names, and updating the Makefile as well.

A future patch will remove the i40e references (after the code
removal patches later in this series).

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>