i40e: Remove VEB recursion

The VEB (virtual embedded switch) as a switch element can be
connected according datasheet though its uplink to:
- Physical port
- Port Virtualizer (not used directly by i40e driver but can
be present in MFP mode where the physical port is shared
between PFs)
- No uplink (aka floating VEB)

But VEB uplink cannot be connected to another VEB and any attempt
to do so results in:

"i40e 0000:02:00.0: couldn't add VEB, err -EIO aq_err I40E_AQ_RC_ENOENT"

that indicates "the uplink SEID does not point to valid element".

Remove this logic from the driver code this way:

1) For debugfs only allow to build floating VEB (uplink_seid == 0)
or main VEB (uplink_seid == mac_seid)
2) Do not recurse in i40e_veb_link_event() as no VEB cannot have
sub-VEBs
3) Ditto for i40e_veb_rebuild() + simplify the function as we know
that the VEB for rebuild can be only the main LAN VEB or some
of the floating VEBs
4) In i40e_rebuild() there is no need to check veb->uplink_seid
as the possible ones are 0 and MAC SEID
5) In i40e_vsi_release() do not take into account VEBs whose
uplink is another VEB as this is not possible
6) Remove veb_idx field from i40e_veb as a VEB cannot have
sub-VEBs

Tested using i40e debugfs interface:
1) Initial state
[root@cnb-03 net-next]# CMD="/sys/kernel/debug/i40e/0000:02:00.0/command"
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 98.440641] i40e 0000:02:00.0: header: 3 reported 3 total
[ 98.446053] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 98.452593] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 98.458856] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16

2) Add floating VEB
[root@cnb-03 net-next]# echo add relay > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 122.745630] i40e 0000:02:00.0: added relay 162
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 136.650049] i40e 0000:02:00.0: header: 4 reported 4 total
[ 136.655466] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 136.661994] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 136.668264] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
[ 136.674787] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0

3) Add VMDQ2 VSI to this new VEB
[root@cnb-03 net-next]# dmesg -c
[ 168.351763] i40e 0000:02:00.0: added VSI 394 to relay 162
[ 168.374652] enp2s0f0np0v0: NIC Link is Up, 40 Gbps Full Duplex, Flow Control: None
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 195.683204] i40e 0000:02:00.0: header: 5 reported 5 total
[ 195.688611] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 195.695143] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 195.701410] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 195.707935] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 195.714201] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16

4) Try to delete the VEB
[root@cnb-03 net-next]# echo del relay 162 > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 239.260901] i40e 0000:02:00.0: deleting relay 162
[ 239.265621] i40e 0000:02:00.0: can't remove VEB 162 with 1 VSIs left

5) Do PF reset and check switch status after rebuild
[root@cnb-03 net-next]# echo pfr > $CMD
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
...
[ 272.333655] i40e 0000:02:00.0: header: 5 reported 5 total
[ 272.339066] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 272.345599] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 272.351862] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 272.358387] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 272.364654] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16

6) Delete VSI and delete VEB
[ 297.199116] i40e 0000:02:00.0: deleting VSI 394
[ 299.807580] i40e 0000:02:00.0: deleting relay 162
[ 309.767905] i40e 0000:02:00.0: header: 3 reported 3 total
[ 309.773318] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 309.779845] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 309.786111] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16

Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: Fix broken support for floating VEBs

Although the i40e supports so-called floating VEB (VEB without
an uplink connection to external network), this support is
broken. This functionality is currently unused (except debugfs)
but it will be used by subsequent series for switchdev mode
slow-path. Fix this by following:

1) Handle correctly floating VEB (VEB with uplink_seid == 0)
in i40e_reconstitute_veb() and look for owner VSI and
create it only for non-floating VEBs and also set bridge
mode only for such VEBs as the floating ones are using
always VEB mode.
2) Handle correctly floating VEB in i40e_veb_release() and
disallow its release when there are some VSIs. This is
different from regular VEB that have owner VSI that is
connected to VEB's uplink after VEB deletion by FW.
3) Fix i40e_add_veb() to handle 'vsi' that is NULL for floating
VEBs. For floating VEB use 0 for downlink SEID and 'true'
for 'default_port' parameters as per datasheet.
4) Fix 'add relay' command in i40e_dbg_command_write() to allow
to create floating VEB by 'add relay 0 0' or 'add relay'

Tested using debugfs:
1) Initial state
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 173.701286] i40e 0000:02:00.0: header: 3 reported 3 total
[ 173.706701] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 173.713241] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 173.719507] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16

2) Add floating VEB
[root@host net-next]# CMD="/sys/kernel/debug/i40e/0000:02:00.0/command"
[root@host net-next]# echo add relay > $CMD
[root@host net-next]# dmesg -c
[ 245.551720] i40e 0000:02:00.0: added relay 162
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 276.984371] i40e 0000:02:00.0: header: 4 reported 4 total
[ 276.989779] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 276.996302] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 277.002569] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
[ 277.009091] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0

3) Add VMDQ2 VSI to this new VEB
[root@host net-next]# echo add vsi 162 > $CMD
[root@host net-next]# dmesg -c
[ 332.314030] i40e 0000:02:00.0: added VSI 394 to relay 162
[ 332.337486] enp2s0f0np0v0: NIC Link is Up, 40 Gbps Full Duplex, Flow Control: None
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 387.284490] i40e 0000:02:00.0: header: 5 reported 5 total
[ 387.289904] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 387.296446] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 387.302708] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 387.309234] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 387.315500] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16

4) Try to delete the VEB
[root@host net-next]# echo del relay 162 > $CMD
[root@host net-next]# dmesg -c
[ 428.749297] i40e 0000:02:00.0: deleting relay 162
[ 428.754011] i40e 0000:02:00.0: can't remove VEB 162 with 1 VSIs left

5) Do PF reset and check switch status after rebuild
[root@host net-next]# echo pfr > $CMD
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 738.056172] i40e 0000:02:00.0: header: 5 reported 5 total
[ 738.061577] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 738.068104] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 738.074367] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 738.080892] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 738.087160] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16

6) Delete VSI and delete VEB
[root@host net-next]# echo del vsi 394 > $CMD
[root@host net-next]# echo del relay 162 > $CMD
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 1233.081126] i40e 0000:02:00.0: deleting VSI 394
[ 1239.345139] i40e 0000:02:00.0: deleting relay 162
[ 1244.886920] i40e 0000:02:00.0: header: 3 reported 3 total
[ 1244.892328] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 1244.898853] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 1244.905119] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16

Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: Add helpers to find VSI and VEB by SEID and use them

Add two helpers i40e_(veb|vsi)_get_by_seid() to find corresponding
VEB or VSI by their SEID value and use these helpers to replace
existing open-coded loops.

Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: Introduce and use macros for iterating VSIs and VEBs

Introduce i40e_for_each_vsi() and i40e_for_each_veb() helper
macros and use them to iterate relevant arrays.

Replace pattern:
for (i = 0; i < pf->num_alloc_vsi; i++)
by:
i40e_for_each_vsi(pf, i, vsi)

and pattern:
for (i = 0; i < I40E_MAX_VEB; i++)
by
i40e_for_each_veb(pf, i, veb)

These macros also check if array item pf->vsi[i] or pf->veb[i]
are not NULL and skip such items so we can remove redundant
checks from loop bodies.

Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: Delete unused and useless i40e_pf fields

Removed fields:
.fc_autoneg_status
Since commit c56999f94876 ("i40e/i40evf: Add set_fc and init of
FC settings") write-only and otherwise unused
.eeprom_version
Write-only and otherwise unused
.atr_sample_rate
Has only one possible value (I40E_DEFAULT_ATR_SAMPLE_RATE). Remove
it and replace its occurrences by I40E_DEFAULT_ATR_SAMPLE_RATE
.adminq_work_limit
Has only one possible value (I40E_AQ_WORK_LIMIT). Remove it and
replace its occurrences by I40E_AQ_WORK_LIMIT
.tx_sluggish_count
Unused, never written
.pf_seid
Used to store VSI downlink seid and it is referenced only once
in the same codepath. There is no need to save it into i40e_pf.
Remove it and use downlink_seid directly in the mentioned log
message.
.instance
Write only. Remove it as well as ugly static local variable
'pfs_found' in i40e_probe.
.int_policy
.switch_kobj
.ptp_pps_work
.ptp_extts1_work
.ptp_pps_start
.pps_delay
.ptp_pin
.override_q_count
All these unused at all

Prior the patch:
pahole -Ci40e_pf drivers/net/ethernet/intel/i40e/i40e.ko | tail -5
/* size: 5368, cachelines: 84, members: 127 */
/* sum members: 5297, holes: 20, sum holes: 71 */
/* paddings: 6, sum paddings: 19 */
/* last cacheline: 56 bytes */
};

After the patch:
pahole -Ci40e_pf drivers/net/ethernet/intel/i40e/i40e.ko | tail -5
/* size: 4976, cachelines: 78, members: 112 */
/* sum members: 4905, holes: 17, sum holes: 71 */
/* paddings: 6, sum paddings: 19 */
/* last cacheline: 48 bytes */
};

Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: Delete unused i40e_mac_info fields

From commit 9eed69a9147c ("i40e: Drop FCoE code from core driver files")
the field i40e_mac_info.san_addr is unused (never filled).
The field i40e_mac_info.max_fcoeq is unused from the beginning.
Remove both.

Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Co-developed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-16-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

i40e: Use DECLARE_BITMAP for flags and hw_features fields in i40e_pf

Convert flags and hw_features fields from i40e_pf from u32 to
bitmaps and their usage to use bit access functions.

Changes:
- Convert "pf_ptr->(flags|hw_features) & FL" to "test_bit(FL, ...)"
- Convert "pf_ptr->(flags|hw_features) |= FL" to "set_bit(FL, ...)"
- Convert "pf_ptr->(flags|hw_features) &= ~FL" to "clear_bit(FL, ...)"
- Rename flag field to bitno in i40e_priv_flags and adjust ethtool
callbacks to work with flags bitmap
- Rename flag names where '_ENABLED'->'_ENA' and '_DISABLED'->'_DIS'
like in ice driver

Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-7-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

i40e: Remove circular header dependencies and fix headers

Similarly as for ice driver [1] there are also circular header
dependencies in i40e driver:
i40e.h -> i40e_virtchnl_pf.h -> i40e.h

Another issue is that i40e header files does not contain their own
dependencies on other header files (both private and standard) so their
inclusion in .c file require to add these deps in certain order to
that .c file to make it compilable.

Fix both issues by removal the mentioned circular dependency, by filling
i40e headers with their dependencies so they can be placed anywhere in
a source code. Additionally remove bunch of includes from i40e.h super
header file that are not necessary and include i40e.h only in .c files
that really require it.

[1] 649c87c6ff52 ("ice: remove circular header dependencies on ice.h")

Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: remove i40e_status

Replace uses of i40e_status to as equivalent as possible error codes.
Remove enum i40e_status as it is no longer needed

Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230728171336.2446156-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

i40e: Fix an NULL vs IS_ERR() bug for debugfs_create_dir()

The debugfs_create_dir() function returns error pointers.
It never returns NULL. Most incorrect error checks were fixed,
but the one in i40e_dbg_init() was forgotten.

Fix the remaining error check.

Fixes: 02e9c290814c ("i40e: debugfs interface")
Signed-off-by: Wang Ming <machel@vivo.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: use int for i40e_status

To prepare for removal of i40e_status, change the variables
from i40e_status to int. This eases the transition when values
are changed to return standard int error codes over enum i40e_status.

As such changes often also change variable orders, a cleanup
is also applied here to make variables conform to RCT and
some lines are also reformatted where applicable.

Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: Add tx_stopped stat

Track TX queue stop events and export the new stat with ethtool.

Signed-off-by: Joe Damato <jdamato@fastly.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: Remove unused RX realloc stat

After commit 1a557afc4dd5 ("i40e: Refactor receive routine"),
rx_stats.realloc_count is no longer being incremented, so remove it.

The debugfs string was left, but hardcoded to 0. This is intended to
prevent breaking any existing code / scripts that are parsing debugfs
for i40e.

Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: stop disabling VFs due to PF error responses

The i40e_vc_send_msg_to_vf_ex (and its wrapper i40e_vc_send_msg_to_vf)
function has logic to detect "failure" responses sent to the VF. If a VF
is sent more than I40E_DEFAULT_NUM_INVALID_MSGS_ALLOWED, then the VF is
marked as disabled. In either case, a dev_info message is printed
stating that a VF opcode failed.

This logic originates from the early implementation of VF support in
commit 5c3c48ac6bf5 ("i40e: implement virtual device interface").

That commit did not go far enough. The "logic" for this behavior seems
to be that error responses somehow indicate a malicious VF. This is not
really true. The PF might be sending an error for any number of reasons
such as lacking resources, an unsupported operation, etc. This does not
indicate a malicious VF. We already have a separate robust malicious VF
detection which relies on hardware logic to detect and prevent a variety
of behaviors.

There is no justification for this behavior in the original
implementation. In fact, a later commit 18b7af57d9c1 ("i40e: Lower some
message levels") reduced the opcode failure message from a dev_err to a
dev_info. In addition, recent commit 01cbf50877e6 ("i40e: Fix to not
show opcode msg on unsuccessful VF MAC change") changed the logic to
allow quieting it for expected failures.

That commit prevented this logic from kicking in for specific
circumstances. This change did not go far enough. The behavior is not
documented nor is it part of any requirement for our products. Other
operating systems such as the FreeBSD implementation of our driver do
not include this logic.

It is clear this check does not make sense, and causes problems which
led to ugly workarounds.

Fix this by just removing the entire logic and the need for the
i40e_vc_send_msg_to_vf_ex function.

Fixes: 01cbf50877e6 ("i40e: Fix to not show opcode msg on unsuccessful VF MAC change")
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: fix unsigned stat widths

Change i40e_update_vsi_stats and struct i40e_vsi to use u64 fields to match
the width of the stats counters in struct i40e_rx_queue_stats.

Update debugfs code to use the correct format specifier for u64.

Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: Fix NULL pointer dereference in i40e_dbg_dump_desc

When trying to dump VFs VSI RX/TX descriptors
using debugfs there was a crash
due to NULL pointer dereference in i40e_dbg_dump_desc.
Added a check to i40e_dbg_dump_desc that checks if
VSI type is correct for dumping RX/TX descriptors.

Fixes: 02e9c290814c ("i40e: debugfs interface")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

intel: clean up mismatched header comments

A bunch of header comments were showing warnings when compiling
with W=1. Fix them all at once. This changes only comments.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: Fix sparse error: uninitialized symbol 'ring'

Init pointer with NULL in default switch case statement.

Previously the error was produced when compiling against sparse.
i40e_debugfs.c:582 i40e_dbg_dump_desc() error: uninitialized symbol 'ring'.

Fixes: 44ea803e2fa7 ("i40e: introduce new dump desc XDP command")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: use 16B HW descriptors instead of 32B

The i40e NIC supports two flavors of HW descriptors, 16 and 32
byte. The latter has, obviously, room for more offloading
information. However, the only fields of the 32B HW descriptor that is
being used by the driver, is also available in the 16B descriptor.

In other words; Reading and writing 32 bytes instead of 16 byte is a
waste of bus bandwidth.

This commit starts using 16 byte descriptors instead of 32 byte
descriptors.

For AF_XDP the rx_drop benchmark was improved by 2%.

Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: introduce new dump desc XDP command

Interfaces already exist for dumping Rx and Tx descriptor information.
Introduce another for doing the same for XDP descriptors.

Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: add XDP ring statistics to dump VSI debug output

Prior to this, only the Rx and Tx ring statistics were dumped. The XDP
ring statistics are now dumped as well.

Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

i40e: remove unused defines

Remove all the unused defines as they are just dead weight.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Remove EMPR traces from debugfs facility

Since commit
'5098850c9b9b ("i40e/i40evf: i40e_register.h updates")'
it is no longer possible to trigger an EMP Reset from debugfs, but it's
possible to request it either way, to end up with a bad reset request:

echo empr > /sys/kernel/debug/i40e/0002\:01\:00.1/command
i40e 0002:01:00.1: debugfs: forcing EMPR
i40e 0002:01:00.1: bad reset request 0x00010000

So let's remove this piece of code and show the available valid commands
as it is when any invalid command is issued.

Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: no need to check return value of debugfs_create functions

When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

i40e: Fix descriptor count manipulation

Changing descriptor count via 'ethtool -G' is not persistent across resets.
When PF reset occurs, we roll back to the default value of vsi->num_desc,
which is used then in i40e_alloc_rings to set descriptor count. XDP does a
PF reset so when user has changed the descriptor count and load XDP
program, the default count will be back there.

To fix this:
* introduce new VSI members - num_tx_desc and num_rx_desc in favour of
num_desc
* set them in i40e_set_ringparam to user's values
* set them to default values in i40e_set_num_rings_in_vsi only when they
don't have previous values

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Use LLDP ethertype define ETH_P_LLDP

Remove references to I40E_ETH_P_LLDP and use ETH_P_LLDP instead.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Further implementation of LLDP

This code implements driver code changes necessary for LLDP
Agent support. Modified i40e_aq_start_lldp() and
i40e_aq_stop_lldp() adding false parameter whether LLDP state
should be persistent across power cycles.

Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: remove debugfs tx_timeout support

The tx_timeout command from debugfs was originally intended to support
early silicon validation efforts. It is no longer needed. Thus remove it to
avoid misuse of triggering tx_timeout through debugfs.

Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Remove unnecessary print statement

Clang warns that the address of a pointer will always evaluated as true
in a boolean context.

drivers/net/ethernet/intel/i40e/i40e_debugfs.c:136:9: warning: address
of array 'vsi->active_vlans' will always evaluate to 'true'
[-Wpointer-bool-conversion]
vsi->active_vlans ? "<valid>" : "<null>");
~~~~~^~~~~~~~~~~~ ~
./include/linux/device.h:1431:33: note: expanded from macro 'dev_info'
_dev_info(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
1 warning generated.

Given that the statement shows that active_vlans is always valid, just
remove the statement since it's not giving any useful information.

Link: https://github.com/ClangBuiltLinux/linux/issues/82
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e/i40evf: cleanup incorrect function doxygen comments

Recent versions of the Linux kernel now warn about incorrect parameter
definitions for function comments. Fix up several function comments to
correctly reflect the current function arguments. This cleans up the
warnings and helps ensure our documentation is accurate.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net: intel: Cleanup the copyright/license headers

After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.

Also caught a few files missing the SPDX license identifier, so fixed
them up.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

intel: add SPDX identifiers to all the Intel drivers

Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

i40e: don't leak memory addresses

Could a Bad Person do Bad Things to a server if they found these
addresses printed in the log? Who knows? But let's not take that risk.

Remove pointers from a bunch of printks. In some cases, I was able to
adjust the message to indicate whether or not the value was null. In
others, I just removed the entire message as there was really no hope of
saving it.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e/i40evf: Only track one ITR setting per ring instead of Tx/Rx

The rings are already split out into Tx and Rx rings so it doesn't make
sense to have any single ring store both a Tx and Rx itr_setting value.
Since that is the case drop the pair in favor of storing just a single ITR
value.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

locking/atomics: COCCINELLE/treewide: Convert trivial ACCESS_ONCE() patterns to READ_ONCE()/WRITE_ONCE()

Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.

For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.

However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:

----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()

// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch

virtual patch

@ depends on patch @
expression E1, E2;
@@

- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)

@ depends on patch @
expression E;
@@

- ACCESS_ONCE(E)
+ READ_ONCE(E)
----

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

i40e: Add macro for PF reset bit

Introduce a macro for the bit setting the PF reset flag and
update its usages. This makes it easier to use this flag
in functions to be introduced in future without encountering
checkpatch issues related to alignment and line over 80
characters.

Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e/i40evf: use DECLARE_BITMAP for state

When using set_bit and friends, we should be using actual
bitmaps, and fix all the locations where we might access
it.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: use DECLARE_BITMAP for state fields

Instead of assuming our flags fit within an unsigned long, use
DECLARE_BITMAP which will ensure that we always allocate enough space.
Additionally, use __I40E_STATE_SIZE__ markers as the last element of the
enumeration so that the size of the BITMAP is compile-time assigned
rather than programmer-time assigned. This ensures that potential future
flag additions do not actually overrun the array. This is especially
important as 32bit systems would only have 32bit longs instead of 64bit
longs as we generally have assumed in the prior code.

This change also removes a dereference of the state fields throughout
the code, so it does have a bit of code churn. The conversions were
automated using sed replacements with an alternation

s/&(vsi->back|vsi|pf)->state/\1->state/
s/&adapter->vsi.state/adapter->vsi.state/

For debugfs, we modify the printing so that we can display chunks of the
state value on new lines. This ensures that we can print the entire set
of state values. Additionally, we now print them as 08lx to ensure that
they display nicely.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: separate PF and VSI state flags

Avoid using the same named flags for both vsi->state and pf->state. This
makes code review easier, as it is more likely that future authors will
use the correct state field when checking bits. Previous commits already
found issues with at least one check, and possibly others may be
incorrect.

This reduces confusion as it is more clear what each flag represents,
and which flags are valid for which state field.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: dump VF information in debugfs

Dump some internal state about VFs through debugfs. This provides
information not available with 'ip link show'. To use, write "dump vf
<id>" to the command file, or just "dump vf" to dump information on all
of the VFs.

Change-ID: Ibe32b7f4ae55d4358c0b903217475f708ada1ecd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Drop FCoE code from core driver files

Looking over the code for FCoE it looks like the Rx path has been broken at
least since the last major Rx refactor almost a year ago. It seems like
FCoE isn't supported for any of the Fortville/Fortpark hardware so there
isn't much point in carrying the code around, especially if it is broken
and untested.

Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: convert to cpu from le16 to generate switch_id correctly

On Big Endian platforms we would incorrectly calculate the wrong switch
id since we did not properly convert the le16 value into CPU format.
Caught by sparse.

Change-ID: I69a2f9fa064a0a91691f7d0e6fcc206adceb8e36
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: use unsigned printf format specifier for active_filters count

Replace the %d specifier used for printing vsi->active_filters and
vsi->promisc_threshold with an unsigned %u format specifier. While it is
unlikely in practice that these values will ever reach such a large
number they are unsigned values and thus should not be interpreted as
negative numbers.

Change-ID: Iff050fad5a1c8537c4c57fcd527441cd95cfc0d4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: store MAC/VLAN filters in a hash with the MAC Address as key

Replace the mac_filter_list with a static size hash table of 8bits. The
primary advantage of this is a decrease in latency of operations related
to searching for specific MAC filters, including .set_rx_mode. Using
a linked list resulted in several locations which were O(n^2). Using
a hash table should give us latency growth closer to O(n*log(n)).

Change-ID: I5330bd04053b880e670210933e35830b95948ebb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

i40e: drop is_vf and is_netdev fields in struct i40e_mac_filter

Originally the is_vf and is_netdev fields were added in order to
distinguish between VF and netdev filters in a single VSI. However, it
can be noted that we use separate VSI for SRIOV VFs and for netdev VSI.
Thus, since a single VSI should only ever have one type of filter, we
can simply remove the checks and remove the typing.

In a similar fashion, we can note that the only remaining way to get
multiple filters of a single type is through a debug command that was
added to debugfs. This command is useless in practice, and results in
causing bugs if we keep counter tracking but lose the is_vf and
is_netdev protections as desired above.

Since the only time we'd actually have a counter value besides 0 and
1 is through use of this debugfs hook, we can remove this unnecessary
command, and the entire counter logic it required.

We vastly simplify mac filters by removing

(a) the distinction between VF and netdev filters
(b) counting logic
(c) the ability to add and remove filters bypassing the stack via debugfs

Change-ID: Idf916dd2a1159b1188ddbab5bef6b85ea6bf27d9
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Clean up handling of msglevel flags and debug parameter

So the i40e driver had a really convoluted configuration for how to handle
the debug flags contained in msg_level. Part of the issue is that the
driver has its own 32 bit mask that it was using to track a separate set of
debug features. From what I can tell it was trying to use the upper 4 bits
to determine if the value was meant to represent a bit-mask or the numeric
value provided by debug level.

What this patch does is clean this up by compressing those 4 bits into bit
31, as a result we just have to perform a check against the value being
negative to determine if we are looking at a debug level (positive), or a
debug mask (negative). The debug level will populate the msg_level, and
the debug mask will populate the debug_mask in the hardware struct.

I added similar logic for ethtool. If the value being provided has bit 31
set we assume the value being provided is a debug mask, otherwise we assume
it is a msg_enable mask. For displaying we only provide the msg_enable,
and if debug_mask is in use we will print it to the dmesg log.

Lastly I removed the debugfs interface. It is redundant with what we
already have in ethtool and really doesn't belong anyway.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Strip out debugfs hook for Flow Director filter programming

This interface was only ever meant for debug only. Since it is not
supposed to be here we are removing it.

Change-ID: Id771a1e5e7d3e2b4b7f56591b61fb48c921e1d04
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: fix "dump port" command when NPAR enabled

When using the debugfs to issue the "dump port" command
with NPAR enabled, the firmware reports back with invalid argument.

The issue occurs because the pf->mac_seid was used to perform the query.
This is fine when NPAR is disabled because the switch ID == pf->mac_seid,
however this is not the case when NPAR is enabled. This fix instead
goes through the VSI to determine the correct ID to use in either case.

Change-ID: I0cd67913a7f2c4a2962e06d39e32e7447cc55b6a
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: refactor Rx filter handling

Properly track filter adds and deletes so the driver doesn't lose filters
during resets and up/down cycles. Add a tracking mechanism so that the
driver knows when to enter and leave promiscuous mode.

Implement a simple state machine so the driver can track the status of
each filter throughout its lifecycle. Properly manage the overflow promiscuous
state for the each VSI, and provide a way for the driver to detect when to exit
overflow promiscuous mode.

Remove all possible default MAC filters that the firmware may have set up so
that the driver can manage these correctly, particularly when VLANs come into
play. Remove the LAA flag for filters; instead just send whatever we get through
set_mac to the firmware as the LAA for wakeup purposes.

Finally, add the state of each filter to debugfs output so we can see what's
going on inside the driver's pointy little head.

Change-ID: I97c5e366fac2254fa01eaff4f65c0af61dcf2e1f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e/i40evf: Remove unused hardware receive descriptor code

The hardware supports a 16 byte descriptor for receive, but the
driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole
lot of complexity while getting rid of the code.

Also since the previous patch made us use no-split mode all the
time, drop any support in the driver for any other value in dtype
and assume it is always zero (aka no-split).

Hooray for code removal!

Change-ID: I2257e902e4dad84a07b94db6d2e6f4ce69b27bc0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Refactor receive routine

This is part 1 of the Rx refactor series, just including
changes to i40e.

This refactor aligns the receive routine with the one in
ixgbe which was highly optimized. This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.

In order to do this:
- consolidate the receive path into a single function that doesn't
use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove ethtool control over packet split

Change-ID: I5ca100721de65992aa0114f8b4bac844b84758e0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e/i40evf: Remove reference to ring->dtype

As part of the rx-refactor, the dtype variable in the i40e_ring
struct is no longer used, so remove it.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Drop packet split receive routine

As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: remove redundant check on vsi->active_vlans

active_vlans is an unsigned long array, hence a null check on this
array is superfluous and can be removed.

Detected with static analysis by smatch:

drivers/net/ethernet/intel/i40e/i40e_debugfs.c:386
i40e_dbg_dump_vsi_seid() warn: this array is probably
non-NULL. 'vsi->active_vlans'

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: queue-specific settings for interrupt moderation

For i40e driver, each vector has its own ITR register. However, there
are no concept of queue-specific settings in the driver proper. Only
global variable is used to store ITR values. That will cause problems
especially when resetting the vector. The specific ITR values could be
lost.
This patch move rx_itr_setting and tx_itr_setting to i40e_ring to store
specific ITR register for each queue.
i40e_get_coalesce and i40e_set_coalesce are also modified accordingly to
support queue-specific settings. To make it compatible with old ethtool,
if user doesn't specify the queue number, i40e_get_coalesce will return
queue 0's value. While i40e_set_coalesce will apply value to all queues.

Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

i40e: Removal of code which relies on BASE VEB SEID

Fixed mapping of SEID is removed from specification. Hence
this patch removes code which was using hard coded base VEB SEID.

Changed FCoE code to use "hw->pf_id" to obtain correct "idx"
and verified.

Removed defines for BASE VSI/VEB SEID and BASE_PF_SEID since it
is not used anymore.

Change-ID: Id507cf4b1fae1c0145e3f08ae9ea5846ea5840de
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: drop unused debugfs file "dump"

There was a completely unused file "dump" in debugfs that
never panned out to be useful.

Change-ID: I12bb9e37b5a83299725dda815a8746157baf6562
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: properly show packet split status in debugfs

Get rid of the unused hsplit field in the ring struct and use the
existing macro to detect packet split enablement. This allows debugfs
dumps of the VSI to properly show which Rx routine is in use.

Change-ID: Ic4e9589e6a788ab196ed0850703f704e30c03781
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e/i40evf: use pages correctly in Rx

Refactor the packet split Rx code to properly use half-pages for
receives. The previous code was doing way more mapping and unmapping
than it needed to, and wasn't properly using half-pages.

Increment the page use count each time we give a half-page to an skb,
knowing that the stack will probably process and release the page before
we need it again. Only free and reallocate pages if the count shows that
both half-pages are in use. Add counters to track reallocations and page
reuse.

Change-ID: I534b299196036b64be82b4861a0a4036310a8f22
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: dump descriptor indexes in hex

The debugging helpers for showing descriptor rings were
dumping the indexes in decimal and the offsets in hex.

Put everything in hex and at least be consistent.

Also update copyright year in file header.

Change-ID: Ia35a21411a2ddb713772dffb4e8718889fcfc895
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: avoid large memcpy by assigning struct

Assign the i40e_pf structure directly instead of using a large memcpy,
which avoids a sparse warning and lets the compiler optimize the copy
since it knows the size of the structure in advance.

Change-ID: I17604e23be2616521eb760290befcb767b52b3f7
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: add netdev info to VSI dump

Add a few more bits of netdev data into the debugfs output for dump VSI.
For now, we'll add the features, hw_features, vlan_features, and flags
bitflags and the state. More could be added later if needed.

Also, tweak a couple nearby output lines for output readability.

Change-ID: I9fb5a9da75c9ad7679498ce9ac3ba24d065ddd2e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Reviewed-by: Brandeburg, Jesse <jesse.brandeburg@intel.com>
Reviewed-by: Wyborny, Carolyn <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: remove unused argument

With the final edition of the patches to remove sleeps from
the driver's entry points, the grab_rtnl argument is no
longer needed, so partially revert the commit that added it.

Change-ID: Ib9778476242586cc9e58b670f5f48d415cb59003
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

intel: i40e: fix confused code

This code is pretty confused. The variable name 'bytes_not_copied'
clearly indicates that the programmer knew the semantics of
copy_{to,from}_user, but then the return value is checked for being
negative and used as a -Exxx return value.

I'm not sure this is the proper fix, but at least we get rid of the
dead code which pretended to check for access faults.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: fix a bug in debugfs with add/del macaddr

The new code flow requires us to grab the filter list lock before
adding/deleting the filter.

Change-ID: I4eaef508ab4da2d1b2e23f20f2a78d931d5b6aeb
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: remove FD atr control from debugfs

Since the flow-director-atr priv flag was added to our ethtool interface,
we don't need the on/off control in debugfs.

Change-ID: Ib3b599916434ab30ccd40074e71d7a81609b5bb5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e/i40evf: clean up some code

Add missings spaces after declarations, remove another __func__ use,
remove uncessary braces, remove unneeded breaks, and useless returns,
and generally fix up some code.

Change-ID: Ie715d6b64976c50e1c21531685fe0a2bd38c4244
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: fix kbuild warnings

The 0day build infrastructure found some issues in i40e, this
removes the warnings by adding a harmless cast to a dev_info.

CC: kbuild-all@01.org
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: limit debugfs io ops

Don't let the debugfs register read and write commands try to access
outside of the ioremapped space. While we're at it, remove the use of
a misleading constant.

Change-ID: Ifce2893e232c65c7a76c23532c658f298218a81b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Fix for recursive RTNL lock during PROMISC change

The sync_vsi_filters function can be called directly under RTNL
or through the timer subtask without one. This was causing a deadlock.

If sync_vsi_filters is called from a thread which held the lock,
and in another thread the PROMISC setting got changed we would
be executing the PROMISC change in the thread which already held
the lock alongside the other filter update. The PROMISC change
requires a reset if we are on a VEB, which requires it to be called
under RTNL.

Earlier the driver would call reset for PROMISC change without
checking if we were already under RTNL and would try to grab it
causing a deadlock. This patch changes the flow to see if we are
already under RTNL before trying to grab it.

Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: use BIT and BIT_ULL macros

Use macros for abstracting (1 << foo) to BIT(foo)
and (1ULL << foo64) to BIT_ULL(foo64) in order to match
better with kernel requirements.

NOTE: the adminq_cmd.h file was not modified on purpose because
of the dependency upon firmware for that file.

Change-ID: I73ee2e48c880d671948aad19bd53ca6b2ac558fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: start up in VEPA mode by default

The patch fixes a bug in the default configuration which
prevented a software bridge loaded on the PF interface from
working correctly because broadcast packets are incorrectly
looped back.

Fix the general case, by loading the driver in VEPA mode Until a
VF or VMDq VSI is added. This way loopback on the Main VSI is
turned off until needed and can resolve the issue of unnecessary
reflection for users that do not have VF or VMDq VSIs setup.

The driver must now coordinate the loopback setting for the Flow
Director (FDIR) VSI to make sure it is in sync with the current
VEB or VEPA mode setting.

The user can still switch bridge modes from the bridge commands and
choose to be in VEPA mode with VF VSIs. Because of hardware
requirements, the call to switch to VEB mode when no VF/VMDqs are
present will be rejected.

NOTE: This patch uses BIT_ULL as that is preferred going forward,
a followup patch in the lower priority queue to net-next will fix
up the remaining 1 << usages.

Change-ID: Ib121ddb18fe4b3c4f52e9deda6fcbeb9105683d1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: enable user dump of internal hardware state

This is a feature to enable better debugging of user reported issues by
allowing a bash script to acquire information about the internal hardware
state. The data output to the kernel log is collected by the script and can
then be sent to Intel. This is a critical debugging feature for helping us
interpret and reproduce complex customer setups.

Change-ID: Ie8b3ab09086d6870a709015f51ada05af10b41bb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: add MAC printing to debugfs dump VSI

Print the LAN, SAN, and Port MACs for the VSI if debugfs command
dump VSI is used on the PF's VSI.

Example output:
[260221.871244] i40e 0000:04:00.0: MAC address: 68:05:ca:26:15:e0 SAN MAC: 00:00:00:00:02:00 Port MAC: 68:05:ca:26:15:e3

Change-ID: I0b393113dfb5ee7ff4f9e5227e4177885f0cc15e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Fix inconsistent use of PF/VF vs pf/vf

Joe Perches pointed out that we were inconsistent in the use of
PF vs pf or VF vs vf in our driver code. Since acronyms are usually
capitalized to denote that it is an acronym, changed all references to
be consistent throughout the code.

Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Remove "hello world" strings from i40e driver

While using the Linux "strings" command I found these two strings in the
driver. There's no need for them and they're kinda silly.

Change-ID: I4e19b02983d48b631e9a9979f49790492845f221
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Fix memory leak at failure path in i40e_dbg_command_write()

The patch fixes a leak of 'cmd_buf' when copy_from_user() failed
in i40e_dbg_command_write().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Add support for getlink, setlink ndo ops

Add support for bridge offload ndo_ops getlink and setlink to
enable bridge hardware mode as per the mode set via IFLA_BRIDGE_MODE.
The support is only enabled in case of a PF VSI and not available for
any other VSI type.

By default the i40e driver inserts a bridge as part of the bring-up
when a FDIR type VSI and/or a FCoE VSI is created. This bridge is
created in VEB mode by default i.e. after creating the bridge using
"Add VEB" AQ command the loopback for the PF's default VSI is enabled.

The patch adds capability where all the VSIs created as downlink to
the bridge inherits the loopback property and enables loopback only
if the uplink bridge is operating in VEB mode.
Hence, there is no need to explicitly enable loopback as part of
allocating resources for SR-IOV VFs and call to do that has been
removed.

In case a user-request is made either via "bridge" utility or using
the bridge netlink interface that requires to change the hardware
bridge mode then that would require a PF reset and rebuild of the
switch hierarchy.

Also update the copyright year.

Change-ID: I4d78fc1c83158efda29ba7be92239b74f75d6d25
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: rename debugfs clear_stats option

Change debugfs command from "clear_stats pf" to "clear_stats port"
to be clearer what the action is. Also, limit the action to the
base PF, not the NPAR partitions.

Change-ID: I22aa39c0962d83a83a985097b1000ed7f8c66f3f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Dump Stats string removed from debugfs help command

Dump Stats string has been removed from functional debugfs
help message. Now it does not show up when we echo command to
debugfs/Fortville queue.

Change-ID: I9333473826b574f1afa6ddb785fd7adfbdcb2884
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Fix possible memory leak in i40e_dbg_dump_desc

I didn't notice that return in the code, fix it by
adding a goto out instead to free the memory.

Fixes:

> New smatch warnings:
> drivers/net/ethernet/intel/i40e/i40e_debugfs.c:832 i40e_dbg_dump_desc() warn: possible memory leak of 'ring'

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Reduce stack in i40e_dbg_dump_desc

Reduce stack use by using kmemdup and not using a very
large struct on stack.

In function ‘i40e_dbg_dump_desc’:
warning: the frame size of 8192 bytes is larger than 2048 bytes [-Wframe-larger-than=]

Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: allow various base numbers in debugfs aq commands

Use the 'i' rather than the more restrictive 'x' or 'd' in the aq_cmd
arguments. This makes the user interface much more forgiving and user
friendly.

Change-ID: I5dcd57b9befc047e06b74cf1152a25a3fa9e1309
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Add support to firmware CEE DCBX mode

This patch allows i40e driver to query and use DCB configuration from
firmware when firmware DCBX agent is in CEE mode.

Change-ID: I30f92a67eb890f0f024f35339696e6e83d49a274
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: remove debugfs dump stats

The debugfs dump stats wasn't being kept up-to-date, was redundant with
the ethtool output, and didn't offer any useful additional info. Rather
than continue trying to keep them aligned, just remove the debugfs command.

Change-ID: Id130ed9aef01c6369ab662c7b4c5ec5b1dbc5b40
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <Jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e/i40evf: Ignore a driver perceived Tx hang if the number of desc pending < 4

We are seeing situations where the driver sees a hang with less than 4
desc pending, if the driver chooses to ignore it the queue progresses
forward and the stack never experiences a real hang.
With this patch we will log a stat when this situation happens
"tx_sluggish" will increment and we can see some more details
at a higher debug level. Other than that we will ignore this
particular case of Tx hang.

Change-ID: I7d1d1666d990e2b12f4f6bed0d17d22e1b6410d5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Adds FCoE related code to i40e core driver

Adds FCoE specific code to existing i40e core driver to:-

1. have separate FCoE VSI with additional FCoE queues pairs.
2. have FCoE related hash defines.
3. have additional FCoE related stats code.
4. export and then re-use existing functions required by FCoE build.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

i40e: fix format mismatch in drivers/net/ethernet/intel/i40e/i40e_debugfs.c

spotted by cppcheck

Signed-off-by: Toralf Förster <toralf.foerster@gmx.de>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Add debugfs hooks to print current total FD filter count

"fd current cnt" can be used to print the total filters consumed
by this interface, this includes guaranteed and best effort filters.

Change-ID: I2c417810c4999ce1388d2ea26f8e69679ba33966
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: debugfs fix to dump remote LLDPDU

Fix the debugfs command "lldp get remote" that dumped the local
LLDPDU instead of peer's LLDPDU.

Change-ID: I0702eacdafd54478c18f20cab3a7fa5dc1b3182d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: allow for more VSIs

The number of VSIs that the firmware reports to us is a guaranteed
minimum, not an absolute maximum. The hardware actually supports far
more than the reported value, which we often need.

To allow for this, we allocate space for a larger number of VSIs than is
guaranteed by the firmware, with the knowledge that we may fail to get
them all in the future.

Note that we are just allocating pointers here, the actual (much larger)
VSI structures are allocated on demand.

Change-ID: I6f4e535ce39d3bf417aef78306e04fbc7505140e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e/i40evf: remove rx_errors and rx_missed

The rx_errors (GLV_REPC) and rx_missed (GLV_RMPC) were removed
from the chip design.

Change-ID: Ifdeb69c90feac64ec95c36d3d32c75e3a06de3b7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Do not expose fd-sb commands from debugfs

Ethtool -k/-K can handle this so we do not need it in debugfs.

Change-ID: I9df692f10a60b71805f8f48d3b87c7da3820b2aa
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: check for netdev before debugfs use

Make sure the VSI has a netdev before trying to use it
in the debugfs netdev_ops commands.

Change-ID: I2d744fc0c32b3226534ce2cde171d9675c5440a6
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Add code to handle FD table full condition

Add code to enforce the following policy:
- If the HW reports filter programming error, we check if it's due to a
full table.
- If so, we go ahead and turn off new rule addition for ATR and then SB
in that order.
- We monitor the programmed filter count, if enough room is created due
to filter deletion/reset, we then re-enable SB and ATR new rule addition.

Change-ID: I69d24b29e5c45bc4fa861258e11c2fa7b8868748
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: cleanup strings

This patch cleans up the strings that the driver prints during normal
operation and moves many strings into dev_dbg. It also cleans up
strings printed during reset.

Change-ID: I1835cc4e3c3b22596182b683284e6bb87eac61b2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Flow Director sideband accounting

This patch completes implementation of the ethtool ntuple
rule management interface. It adds the get, update and delete
interface reset.

Change-ID: Ida7f481d9ee4e405ed91340b858eabb18a52fdb5
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: add DCB and DCBNL support

This patch adds capability to configure DCB on i40e network
interfaces using Intel XL710 adapter firmware APIs.

By default all VSIs are only enabled for the default traffic
class enabled by firmware for any given PF. The driver would
query the firmware for the traffic classes that are enabled for
the port and reconfigure the LAN VSI to match to the port traffic
class settings. All other VSIs are only enabled for the default
traffic class settings for now.

The driver registers and listens to firmware events that may
require change in the DCB settings. It may reconfigure the VSI
settings based on these events.

This patch exposes IEEE DCBNL interfaces for the i40e driver to
allow any application to query the DCB settings on the adapter.

Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

i40e: refactor flow director

The i40e hardware was generating some inconsistent results
when using current programming methods. This refactor
fixes the inconsistencies that were preventing clean
unloads of the driver, and moves the queues for handling
flow director errors into their own hardware VSI.

This patch also implements a corrected version of the
basic ethtool add ntuple rule, which will disable
the driver's automatic flow programming. A future patch
adds remove/replay/list support for ntuple.

Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

i40e: check desc pointer before printing

Check that the descriptors were allocated before trying to dump
them to the logfile. While we're there, de-trick-ify the code
so as to be easier to read and not abusing the types and unions.

Change-ID: I22898f4b22cecda3582d4d9e4018da9cd540f177
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

i40e: fix log message wording

Change the redundant "vsi VSI" to VSI.

Change-ID: Ic16ea5820a99abc7831713cde39e7d032a7ba4d3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: shorten wordy fields

The alloc_rx_buff_failed and alloc_rx_page_failed variables
are both part of an rx specific structure so just remove
the _rx part of the name. No functional changes.

Change-ID: Icffa2f5d13c6f2b1e09cf45b9472b83c9dae8fc6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Fix GPL header

The GPL header included in each file in the i40e driver doesn't
need to include the "this program" text since this driver
is already part of the larger kernel.

Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Expose AQ debugfs hooks

Add more functionality to debugfs to assist development
and testing of AQ commands.

adds:
send aq_cmd
send indirect aq_cmd

Change-Id: I01710cddd33110a6c1e1aabf84cb6e93cda4c42a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: fix whitespace

Trivial whitespace fix.

Change-Id: Ib7c70891a33c4b3d200c69367549d0dbdee0f076
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: keep allocated memory in structs

Save both a pointer to memory and the length in order to store all
info about allocated kernel memory. This patch changes some adminq
allocations to preserve the full i40e_dma_mem/i40e_virt_mem structs
for every allocation.

Change-Id: Ibcf96159aba4ba61f839d16d87d19478df28e630
Signed-off-by: David Cassard <david.g.cassard@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Dump the whole NVM, not half

Debugfs was reading exactly half the number of words, fix it.

Change-Id: Ieb217f3c6dca455d44e50a0dc61a6664c0cb2265
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Fix off by one in i40e_dbg_command_write

We assume that the resulting buffer is zero terminated when we then
re-use it. The sscanf is limited to 512 bytes but needs to be 511
to allow for a terminator.

One of a set of problems noted by Jackie Chang

Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Shannon Nelson <Shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: more print_hex_dump use

Take advantage of print_hex_dump() in another couple places to
clean up the code.

Change-Id: Ib618e75f928308c0afd0d8d74105da0c6577a024
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: fix up scanf decoders

Fix up a couple of scanfs to accept various base numbers instead of silently
requiring hex.

Change-Id: I1cc4dffbb1d011bf603cbf34a8db093da57fad7a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: simplify error messages for dump descriptor

debugfs fixes: We don't really need to give usage messages for data errors,
only for invalid command errors.

Change-Id: If3f74ac49e43c3ced7fd388323fa738ac145e055
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: prevent null pointer exception in dump descriptor

Check that rings were allocated before trying to reference them.

Change-Id: I33151e55ab7a7a305fecdb88ccb2709ac246b7c7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Fix dump output from debugfs calls

The debugfs commands that dump hex information are not doing these as
expected viz. "lldp get local", "nvm read", "dump debug fwdata", etc.

Use print_hex_dump() instead to hex dump and remove the print buffer
stuff from the code.

Change-Id: I507bd8b2187aae8bad5055b7872978c309cf143e
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: rtnl_lock in reset path fixes

Any user-initiated path which eventually calls reset needs
to hold the rtnl_lock, so add functionality to do that.

Be careful not to use the safe reset when cleaning up
from the diagnostic tests, which avoids rtnl_lock
recursion from ethtool.

Protect the reset_task with rtnl_lock, since it runs from a work item.

Change-Id: Ib6e7a3fb2966809db2daf35fd5a123ccdf6f6f0f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: add support for triggering EMPR

Allow debugfs to trigger a reset called EMPR.

Change-Id: I2f6600a8242759ec60c8198d03f70c2b774e0740
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: check vsi ptrs before dumping them

Make sure there really are rings and queues before trying to dump
information in them.

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: reorder block declarations in debugfs

This is a cleanup of the local variables declared at the beginning
of each function.

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: fix use of untrusted scalar value warning

This is a fix for an issue reported by coverity, reported by
Hannes Frederic Sowa.

I'm unable to test if this patch actually fixes the coverity
reported issue, feedback is welcome.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: clamp debugfs nvm read command

This issue was identified by the coverity checker where we were
not checking the upper limit on reads, reported by Hannes
Frederic Sowa.

Implement more specific limits on reads (min 1k, max 4k)

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: debugfs fixups

debugfs fixes for issues found by coverity.

This issue was identified by the coverity checker, reported by Hannes Frederic
Sowa.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Move rings from pointer to array to array of pointers

Allocate the queue pairs individually instead of as a group. This
allows for much easier queue management as it is possible to dynamically
resize the queues without having to free and allocate the entire block.

Ease statistic collection by treating Tx/Rx queue pairs as a single
unit. Each pair is allocated together and starts with a Tx queue and
ends with an Rx queue. By ordering them this way it is possible to know
the Rx offset based on a pointer to the Tx queue.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Move q_vectors from pointer to array to array of pointers

Allocate the q_vectors individually. The advantage to this is that it
allows for easier freeing and allocation. In addition it makes it so
that we could do node specific allocations at some point in the future.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Split bytes and packets from Rx/Tx stats

This makes it so that the Tx and Rx byte and packet counts are
separated from the rest of the statistics. This allows for better
isolation of these stats when we move them into the 64 bit statistics.

Simplify things by re-ordering how the stats display in ethtool.
Instead of displaying all of the Tx queues as a block, followed by all
the Rx queues, the new order is Tx[0], Rx[0], Tx[1], Rx[1], ..., Tx[n],
Rx[n]. This reduces the loops and cleans up the display for testing
purposes since it is very easy to verify if flow director is doing the
right thing as the Tx and Rx queue pair are shown in pairs.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: Drop unused completed stat

The Tx "completed" stat was part of the original rewrite for detecting
Tx hangs. However some time ago in ixgbe I determined that we could
just use the packets stat instead. Since then this stat was
removed from ixgbe and it serves no purpose in i40e so it can be
dropped.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: debugfs interface

This driver includes a debugfs interface for developers to get more hardware
information in real-time.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>