e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue

Forcing SMBUS inside the ULP enabling flow leads to sporadic PHY loss on
some systems. It is suspected to be caused by initiating PHY transactions
before the interface settles.

Separating this configuration from the ULP enabling flow and moving it to
the shutdown function allows enough time for the interface to settle and
avoids adding a delay.

Fixes: 6607c99e7034 ("e1000e: i219 - fix to enable both ULP and EEE in Sx state")
Co-developed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Minor flow correction in e1000_shutdown function

Add curly braces to avoid entering to an if statement where it is not
always required in e1000_shutdown function.
This improves code readability and might prevent non-deterministic
behaviour in the future.

Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240301184806.2634508-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

intel: legacy: field get conversion

Refactor several older Intel drivers to use FIELD_GET(), which reduces
lines of code and adds clarity of intent.

This code was generated by the following coccinelle/spatch script and
then manually repaired.

@get@
constant shift,mask;
type T;
expression a;
@@
(
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)

and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/

Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Add support for the next LOM generation

Add devices IDs for the next LOM generations that will be available on the
next Intel Client platforms. This patch provides the initial support for
these devices.

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Use PME poll to circumvent unreliable ACPI wake

On some I219 devices, ethernet cable plugging detection only works once
from PCI D3 state. Subsequent cable plugging does set PME bit correctly,
but device still doesn't get woken up.

Since I219 connects to the root complex directly, it relies on platform
firmware (ACPI) to wake it up. In this case, the GPE from _PRW only
works for first cable plugging but fails to notify the driver for
subsequent plugging events.

The issue was originally found on CNP, but the same issue can be found
on ADL too. So workaround the issue by continuing use PME poll after
first ACPI wake. As PME poll is always used, the runtime suspend
restriction for CNP can also be removed.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Add @adapter description to kdoc

Provide a description for the kernel doc of the @adapter
of e1000e_trigger_lsc()

Signed-off-by: Baozhu Ni <nibaozhu@yeah.net>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Remove unnecessary aer.h include

<linux/aer.h> is unused, so remove it.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

e1000e: Disable TSO on i219-LM card to increase speed

While using i219-LM card currently it was only possible to achieve
about 60% of maximum speed due to regression introduced in Linux 5.8.
This was caused by TSO not being disabled by default despite commit
f29801030ac6 ("e1000e: Disable TSO for buffer overrun workaround").
Fix that by disabling TSO during driver probe.

Fixes: f29801030ac6 ("e1000e: Disable TSO for buffer overrun workaround")
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230417205345.1030801-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

e1000e: Remove redundant pci_enable_pcie_error_reporting()

pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.

Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.

Note that this doesn't control interrupt generation by the Root Port; that
is controlled by the AER Root Error Command register, which is managed by
the AER service driver.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Remove unnecessary use of kmap_atomic()

alloc_rx_buf() allocates ps_page->page and buffer_info->page using either
GFP_ATOMIC or GFP_KERNEL. Memory allocated with GFP_KERNEL/GFP_ATOMIC can't
come from highmem and so there's no need to kmap() them. Just use
page_address().

I don't have access to a 32-bit system so did some limited testing on qemu
(qemu-system-i386 -m 4096 -smp 4 -device e1000e) with a 32-bit Debian 11.04
image.

Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Suggested-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Add e1000e trace module

Add tracepoints to the driver via a new file e1000e_trace.h and some new
trace calls added in interesting places in the driver. Add some tracing
for s0ix flows to help in a debug of shared resources with the CSME
firmware. The idea here is that tracepoints have such low performance cost
when disabled that we can leave these in the upstream driver.

Performance not affected, and this can be very useful for debugging and
adding new trace events to paths in the future.

Usage:
echo "e1000e_trace:*" > /sys/kernel/debug/tracing/set_event
echo 1 > /sys/kernel/debug/tracing/events/e1000e_trace/enable

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Add support for the next LOM generation

Add devices IDs for the next LOM generations that will be available on the
next Intel Client platforms.
This patch provides the initial support for these devices.

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Separate MTP board type from ADP

We have the same LAN controller on different PCH's. Separate MTP board
type from an ADP which will allow for specific fixes to be applied for MTP
platforms.

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Fix TX dispatch condition

e1000_xmit_frame is expected to stop the queue and dispatch frames to
hardware if there is not sufficient space for the next frame in the
buffer, but sometimes it failed to do so because the estimated maximum
size of frame was wrong. As the consequence, the later invocation of
e1000_xmit_frame failed with NETDEV_TX_BUSY, and the frame in the buffer
remained forever, resulting in a watchdog failure.

This change fixes the estimated size by making it match with the
condition for NETDEV_TX_BUSY. Apparently, the old estimation failed to
account for the following lines which determines the space requirement
for not causing NETDEV_TX_BUSY:
```
/* reserve a descriptor for the offload context */
if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
count++;
count++;

count += DIV_ROUND_UP(len, adapter->tx_fifo_limit);
```

This issue was found when running http-stress02 test included in Linux
Test Project 20220930 on QEMU with the following commandline:
```
qemu-system-x86_64 -M q35,accel=kvm -m 8G -smp 8
-drive if=virtio,format=raw,file=root.img,file.locking=on
-device e1000e,netdev=netdev
-netdev tap,script=ifup,downscript=no,id=netdev
```

Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

net: drop the weight argument from netif_napi_add

We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().

Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: move from strlcpy with unused retval to strscpy

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

e1000e: convert .adjfreq to .adjfine

The PTP implementation for the e1000e driver uses the older .adjfreq
method. This method takes an adjustment in parts per billion. The newer
.adjfine implementation uses scaled_ppm. The use of scaled_ppm allows for
finer grained adjustments and is preferred over using the older
implementation.

Make use of mul_u64_u64_div_u64 in order to handle possible overflow of the
multiplication used to calculate the desired adjustment to the hardware
increment value.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

net: add skb_[inner_]tcp_all_headers helpers

Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)"
to compute headers length for a TCP packet, but others
use more convoluted (but equivalent) ways.

Add skb_tcp_all_headers() and skb_inner_tcp_all_headers()
helpers to harmonize this a bit.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "e1000e: Fix possible HW unit hang after an s0ix exit"

This reverts commit 1866aa0d0d6492bc2f8d22d0df49abaccf50cddd.

Commit 1866aa0d0d64 ("e1000e: Fix possible HW unit hang after an s0ix
exit") was a workaround for CSME problem to handle messages comes via H2ME
mailbox. This problem has been fixed by patch "e1000e: Enable the GPT
clock before sending message to the CSME".

Fixes: 3e55d231716e ("e1000e: Add handshake with the CSME to support S0ix")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214821
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Enable GPT clock before sending message to CSME

On corporate (CSME) ADL systems, the Ethernet Controller may stop working
("HW unit hang") after exiting from the s0ix state. The reason is that
CSME misses the message sent by the host. Enabling the dynamic GPT clock
solves this problem. This clock is cleared upon HW initialization.

Fixes: 3e55d231716e ("e1000e: Add handshake with the CSME to support S0ix")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214821
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Remove useless DMA-32 fallback configuration

As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.

So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be
1.

Simplify code and remove some dead code accordingly.

[1]: https://lkml.org/lkml/2021/6/7/398

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Fix possible HW unit hang after an s0ix exit

Disable the OEM bit/Gig Disable/restart AN impact and disable the PHY
LAN connected device (LCD) reset during power management flows. This
fixes possible HW unit hangs on the s0ix exit on some corporate ADL
platforms.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214821
Fixes: 3e55d231716e ("e1000e: Add handshake with the CSME to support S0ix")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Suggested-by: Nir Efrati <nir.efrati@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Handshake with CSME starts from ADL platforms

Handshake with CSME/AMT on none provisioned platforms during S0ix flow
is not supported on TGL platform and can cause to HW unit hang. Update
the handshake with CSME flow to start from the ADL platform.

Fixes: 3e55d231716e ("e1000e: Add handshake with the CSME to support S0ix")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Separate ADP board type from TGP

We have the same LAN controller on different PCH's. Separate ADP board
type from a TGP which will allow for specific fixes to be applied for
ADP platforms.

Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

net_tstamp: add new flag HWTSTAMP_FLAG_BONDED_PHC_INDEX

Since commit 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.

This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.

With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.

Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Remove redundant statement

This assignment statement is meaningless, because the statement
will execute to the tag "set_itr_now".

The clang_analyzer complains as follows:

drivers/net/ethernet/intel/e1000e/netdev.c:2552:3 warning:

Value stored to 'current_itr' is never read.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet: use eth_hw_addr_set() for dev->addr_len cases

Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():

@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)

In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Separate TGP board type from SPT

We have the same LAN controller on different PCHs. Separate TGP board
type from SPT which will allow for specific fixes to be applied for
TGP platforms.

Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

dev_ioctl: split out ndo_eth_ioctl

Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.

Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.

This is a purely cosmetic change intended to help readers find
their way through the implementation.

Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/e1000e: Fix spelling mistake "The" -> "This"

There is a spelling mistake in the comment block.

Signed-off-by: Tree Davies <tdavies@darkphysics.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Add support for the next LOM generation

Add devices IDs for the next LOM generations that will be
available on the next Intel Client platforms
This patch provides the initial support for these devices

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Add support for Lunar Lake

Add devices IDs for the next LOM generations that will be
available on the next Intel Client platform (Lunar Lake)
This patch provides the initial support for these devices

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Additional PHY power saving in S0ix

After transferring the MAC-PHY interface to the SMBus set the PHY
to S0ix low power idle mode.

Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Add polling mechanism to indicate CSME DPG exit

Per guidance from the CSME architecture team, it may take
up to 1 second for unconfiguring dynamic power gating mode.
Practically it can take more time. Wait up to 2.5 seconds to indicate
dynamic power gating exit from the S0ix configuration. Detect
scenarios that take more than 1 second but less than 2.5 seconds
will emit warning message.

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Add handshake with the CSME to support S0ix

On the corporate system, the driver will ask from the CSME
(manageability engine) to perform device settings are required
to allow S0ix residency.
This patch provides initial support.

Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Fix an error handling path in 'e1000_probe()'

If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.

Fixes: 111b9dc5c981 ("e1000e: add aer support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Check the PCIm state

Complete to commit def4ec6dce393e ("e1000e: PCIm function state support")
Check the PCIm state only on CSME systems. There is no point to do this
check on non CSME systems.
This patch fixes a generation a false-positive warning:
"Error in exiting dmoff"

Fixes: def4ec6dce39 ("e1000e: PCIm function state support")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: e1000e: remove repeated word "slot" for netdev.c

There are double "slot" in comment, so remove the redundant one.

Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Fix prototype warning

Correct report warnings in ich8lan.c, netdev.c phy.c and ptp.c files

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Mark e1000e_pm_prepare() as __maybe_unused

The function e1000e_pm_prepare() may have no callers depending
on configuration, so it must be marked __maybe_unused to avoid
harmless warning:

drivers/net/ethernet/intel/e1000e/netdev.c:6926:12:
warning: 'e1000e_pm_prepare' defined but not used [-Wunused-function]
6926 | static int e1000e_pm_prepare(struct device *dev)
| ^~~~~~~~~~~~~~~~~

Fixes: ccf8b940e5fd ("e1000e: Leverage direct_complete to speed up s2ram")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Remove the runtime suspend restriction on CNP+

Although there is platform issue of runtime suspend support
on CNP, it would be more flexible to let the user decide whether
to disable runtime or not because:
1. This can be done in userspace via
echo on > /sys/devices/pci0000\:00/0000\:00\:1f.d/power/control
2. More and more NICs would support runtime suspend, disabling the
runtime suspend on them by default would impact the validation.

Only disable runtime suspend on CNP in case of any user space regression.

Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Leverage direct_complete to speed up s2ram

The NIC is put in runtime suspend status when there is no cable connected.
As a result, it is safe to keep non-wakeup NIC in runtime suspended during
s2ram because the system does not rely on the NIC plug event nor WoL to wake
up the system. Besides that, unlike the s2idle, s2ram does not need to
manipulate S0ix settings during suspend.

This patch introduces the .prepare() for e1000e so that if the NIC is runtime
suspended the subsequent suspend/resume hooks will be skipped so as to speed
up the s2ram. The pm core will check whether the NIC is a wake up device so
there's no need to check it again in .prepare(). DPM_FLAG_SMART_PREPARE flag
should be set during probe to ask the pci subsystem to honor the driver's
prepare() result. Besides, the NIC remains runtime suspended after resumed
from s2ram as there is no need to resume it.

Tested on i7-2600K with 82579V NIC
Before the patch:
e1000e 0000:00:19.0: pci_pm_suspend+0x0/0x160 returned 0 after 225146 usecs
e1000e 0000:00:19.0: pci_pm_resume+0x0/0x90 returned 0 after 140588 usecs

After the patch:
echo disabled > //sys/devices/pci0000\:00/0000\:00\:19.0/power/wakeup
becomes 0 usecs because the hooks will be skipped.

Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: add rtnl_lock() to e1000_reset_task

A possible race condition was found in e1000_reset_task,
after discovering a similar issue in igb driver via
commit 024a8168b749 ("igb: reinit_locked() should be called
with rtnl_lock").

Added rtnl_lock() and rtnl_unlock() to avoid this.

Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Export S0ix flags to ethtool

This flag can be used by an end user to disable S0ix flows on a
buggy system or by an OEM for development purposes.

If you need this flag to be persisted across reboots, it's suggested
to use a udev rule to call adjust it until the kernel could have your
configuration in a disallow list.

Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Revert "e1000e: disable s0ix entry and exit flows for ME systems"

commit e086ba2fccda ("e1000e: disable s0ix entry and exit flows for ME
systems") disabled s0ix flows for systems that have various incarnations of
the i219-LM ethernet controller. This changed caused power consumption
regressions on the following shipping Dell Comet Lake based laptops:
* Latitude 5310
* Latitude 5410
* Latitude 5410
* Latitude 5510
* Precision 3550
* Latitude 5411
* Latitude 5511
* Precision 3551
* Precision 7550
* Precision 7750

This commit was introduced because of some regressions on certain Thinkpad
laptops. This comment was potentially caused by an earlier
commit 632fbd5eb5b0e ("e1000e: fix S0ix flows for cable connected case").
or it was possibly caused by a system not meeting platform architectural
requirements for low power consumption. Other changes made in the driver
with extended timeouts are expected to make the driver more impervious to
platform firmware behavior.

Fixes: e086ba2fccda ("e1000e: disable s0ix entry and exit flows for ME systems")
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: Only run S0ix flows if shutdown succeeded

If the shutdown failed, the part will be thawed and running
S0ix flows will put it into an undefined state.

Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: fix S0ix flow to allow S0i3.2 subset entry

Changed a configuration in the flows to align with
architecture requirements to achieve S0i3.2 substate.

This helps both i219V and i219LM configurations.

Also fixed a typo in the previous commit 632fbd5eb5b0
("e1000e: fix S0ix flows for cable connected case").

Fixes: 632fbd5eb5b0 ("e1000e: fix S0ix flows for cable connected case").
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Link: https://lore.kernel.org/r/20201208185632.151052-1-mario.limonciello@dell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

e1000e: Add support for Meteor Lake

Add devices IDs for the next LOM generations that will be
available on the next Intel Client platform (Meteor Lake)
This patch provides the initial support for these devices

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

intel-ethernet: clean up W=1 warnings in kdoc

This takes care of all of the trivial W=1 fixes in the Intel
Ethernet drivers, which allows developers and maintainers to
build more of the networking tree with more complete warning
checks.

There are three classes of kdoc warnings fixed:
- cannot understand function prototype: 'x'
- Excess function parameter 'x' description in 'y'
- Function parameter or member 'x' not described in 'y'

All of the changes were trivial comment updates on
function headers.

Inspired by Lee Jones' series of wireless work to do the same.
Compile tested only, and passes simple test of
$ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \
xargs scripts/kernel-doc -none

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

treewide: Use fallthrough pseudo-keyword

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

ethernet/intel: Convert fallthrough code comments

Convert all the remaining 'fall through" code comments to the newer
'fallthrough;' keyword.

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

net/intel: remove driver versions from Intel drivers

As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.

For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.

What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.

CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>

e1000e: fix unused-function warning

The CONFIG_PM_SLEEP #ifdef checks in this file are inconsistent,
leading to a warning about sometimes unused function:

drivers/net/ethernet/intel/e1000e/netdev.c:137:13: error: unused function 'e1000e_check_me' [-Werror,-Wunused-function]

Rather than adding more #ifdefs, just remove them completely
and mark the PM functions as __maybe_unused to let the compiler
work it out on it own.

Fixes: e086ba2fccda ("e1000e: disable s0ix entry and exit flows for ME systems")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Do not wake up the system via WOL if device wakeup is disabled

Currently the system will be woken up via WOL(Wake On LAN) even if the
device wakeup ability has been disabled via sysfs:
cat /sys/devices/pci0000:00/0000:00:1f.6/power/wakeup
disabled

The system should not be woken up if the user has explicitly
disabled the wake up ability for this device.

This patch clears the WOL ability of this network device if the
user has disabled the wake up ability in sysfs.

Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver")
Reported-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Relax condition to trigger reset for ME workaround

It's an error if the value of the RX/TX tail descriptor does not match
what was written. The error condition is true regardless the duration
of the interference from ME. But the driver only performs the reset if
E1000_ICH_FWSM_PCIM2PCI_COUNT (2000) iterations of 50us delay have
transpired. The extra condition can lead to inconsistency between the
state of hardware as expected by the driver.

Fix this by dropping the check for number of delay iterations.

While at it, also make __ew32_prepare() static as it's not used
anywhere else.

CC: stable <stable@vger.kernel.org>
Signed-off-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: disable s0ix entry and exit flows for ME systems

Since ME systems do not support SLP_S0 in S0ix state, and S0ix entry
and exit flows may cause errors on them it is best to avoid using
e1000e_s0ix_entry_flow and e1000e_s0ix_exit_flow functions.

This was done by creating a struct of all devices that comes with ME
and by checking if the current device has ME.

Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Disable TSO for buffer overrun workaround

Commit b10effb92e27 ("e1000e: fix buffer overrun while the I219 is
processing DMA transactions") imposes roughly 30% performance penalty.

The commit log states that "Disabling TSO eliminates performance loss
for TCP traffic without a noticeable impact on CPU performance", so
let's disable TSO by default to regain the loss.

CC: stable <stable@vger.kernel.org>
Fixes: b10effb92e27 ("e1000e: fix buffer overrun while the I219 is processing DMA transactions")
BugLink: https://bugs.launchpad.net/bugs/1802691
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

PM: sleep: core: Rename DPM_FLAG_NEVER_SKIP

Rename DPM_FLAG_NEVER_SKIP to DPM_FLAG_NO_DIRECT_COMPLETE which
matches its purpose more closely.

No functional impact.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # for PCI parts
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>

e1000e: fix S0ix flows for cable connected case

Added a fix to S0ix entry and exit flows for TGP and above
MAC types, to the case when the Ethernet cable is connected
and the link is up. With that the system is able to reach
SLP_S0 when going to freeze power state.

Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Add support for Tiger Lake device

Added support for a device id that is a part of the Intel Tiger Lake
platform.

Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Add support for Alder Lake

Add devices ID's for the next LOM generations that will be
available on the next Intel Client platform (Alder Lake)
This patch provides the initial support for these devices

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix missing cpu_to_le64 on buffer_addr

The following warning suggests there is a missing cpu_to_le64() in
the e1000_flush_tx_ring() function (it is also the behaviour
elsewhere in the driver to do cpu_to_le64() on the buffer_addr
when setting it)

drivers/net/ethernet/intel/e1000e/netdev.c:3813:30: warning: incorrect type in assignment (different base types)
drivers/net/ethernet/intel/e1000e/netdev.c:3813:30: expected restricted __le64 [usertype] buffer_addr
drivers/net/ethernet/intel/e1000e/netdev.c:3813:30: got unsigned long long [usertype] dma

Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000(e): use new helper tcp_v6_gso_csum_prep

Use new helper tcp_v6_gso_csum_prep in additional network drivers.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers: net: Call cpu_latency_qos_*() instead of pm_qos_*()

Call cpu_latency_qos_add/update/remove_request() instead of
pm_qos_add/update/remove_request(), respectively, because the
latter are going to be dropped.

No intentional functional impact.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>

e1000e: Revert "e1000e: Make watchdog use delayed work"

This reverts commit 59653e6497d16f7ac1d9db088f3959f57ee8c3db.

This is due to this commit causing driver crashes and connections to
reset unexpectedly.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>

e1000e: Use netdev_info instead of pr_info for link messages

Replace the pr_info calls with netdev_info in all cases related to the
netdevice link state.

As a result of this patch the link messages will change as shown below.
Before:
e1000e: ens3 NIC Link is Down
e1000e: ens3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx

After:
e1000e 0000:00:03.0 ens3: NIC Link is Down
e1000e 0000:00:03.0 ens3: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

netdev: pass the stuck queue to the timeout handler

This allows incrementing the correct timeout statistic without any mess.
Down the road, devices can learn to reset just the specific queue.

The patch was generated with the following script:

use strict;
use warnings;

our $^I = '.bak';

my @work = (
["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"],
["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"],
["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"],
["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"],
["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"],
["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"],
["drivers/net/appletalk/cops.c", "cops_timeout"],
["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"],
["drivers/net/arcnet/arcnet.c", "arcnet_timeout"],
["drivers/net/arcnet/com20020.c", "arcnet_timeout"],
["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"],
["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"],
["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"],
["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"],
["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"],
["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"],
["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"],
["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"],
["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"],
["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"],
["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"],
["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"],
["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"],
["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"],
["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"],
["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"],
["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"],
["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"],
["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"],
["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"],
["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"],
["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"],
["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"],
["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"],
["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"],
["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"],
["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"],
["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"],
["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"],
["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"],
["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"],
["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"],
["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"],
["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"],
["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"],
["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"],
["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"],
["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"],
["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"],
["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"],
["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"],
["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"],
["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"],
["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"],
["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"],
["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"],
["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"],
["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"],
["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"],
["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"],
["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"],
["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"],
["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"],
["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"],
["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"],
["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"],
["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"],
["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"],
["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"],
["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"],
["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"],
["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"],
["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"],
["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"],
["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"],
["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"],
["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"],
["drivers/net/ethernet/jme.c", "jme_tx_timeout"],
["drivers/net/ethernet/korina.c", "korina_tx_timeout"],
["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"],
["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"],
["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"],
["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"],
["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"],
["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"],
["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"],
["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"],
["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"],
["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"],
["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"],
["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"],
["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"],
["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"],
["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"],
["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"],
["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"],
["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"],
["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"],
["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"],
["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"],
["drivers/net/ethernet/realtek/atp.c", "tx_timeout"],
["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"],
["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"],
["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"],
["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"],
["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"],
["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"],
["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"],
["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"],
["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"],
["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"],
["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"],
["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"],
["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"],
["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"],
["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"],
["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"],
["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"],
["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"],
["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"],
["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"],
["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"],
["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"],
["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"],
["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"],
["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"],
["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"],
["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"],
["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"],
["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"],
["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"],
["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"],
["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"],
["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"],
["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"],
["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"],
["drivers/net/slip/slip.c", "sl_tx_timeout"],
["include/linux/usb/usbnet.h", "usbnet_tx_timeout"],
["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"],
["drivers/net/usb/catc.c", "catc_tx_timeout"],
["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"],
["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"],
["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"],
["drivers/net/usb/hso.c", "hso_net_tx_timeout"],
["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"],
["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"],
["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"],
["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"],
["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"],
["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"],
["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"],
["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"],
["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"],
["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"],
["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"],
["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"],
["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"],
["drivers/net/wan/cosa.c", "cosa_net_timeout"],
["drivers/net/wan/farsync.c", "fst_tx_timeout"],
["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"],
["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"],
["drivers/net/wan/x25_asy.c", "x25_asy_timeout"],
["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"],
["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"],
["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"],
["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"],
["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"],
["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"],
["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"],
["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"],
["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"],
["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"],
["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"],
["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"],
["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"],
["drivers/tty/synclink.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"],
["net/atm/lec.c", "lec_tx_timeout"],
["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"]
);

for my $p (@work) {
my @pair = @$p;
my $file = $pair[0];
my $func = $pair[1];
print STDERR $file , ": ", $func,"\n";
our @ARGV = ($file);
while (<ARGV>) {
if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) {
print STDERR "found $1+$2 in $file\n";
}
if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) {
print STDERR "$func found in $file\n";
}
print;
}
}

where the list of files and functions is simply from:

git grep ndo_tx_timeout, with manual addition of headers
in the rare cases where the function is from a header,
then manually changing the few places which actually
call ndo_tx_timeout.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Martin Habets <mhabets@solarflare.com>

changes from v9:
fixup a forward declaration
changes from v9:
more leftovers from v3 change
changes from v8:
fix up a missing direct call to timeout
rebased on net-next
changes from v7:
fixup leftovers from v3 change
changes from v6:
fix typo in rtl driver
changes from v5:
add missing files (allow any net device argument name)
changes from v4:
add a missing driver header
changes from v3:
change queue # to unsigned
Changes from v2:
added headers
Changes from v1:
Fix errors found by kbuild:
generalize the pattern a bit, to pick up
a couple of instances missed by the previous
version.

Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: intel: Demote MTU change prints to debug

Changing a network device MTU can be a fairly frequent operation, and
failure to change the MTU is reflected to user-space properly, both by
an appropriate message as well as by looking at whether the device's MTU
matches the configuration.

Demote the prints to debug prints by using netdev_dbg(), making all
Intel wired LAN drivers consistent, since they used a mixture of PCI
device and network device prints before.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Fix compiler warning when CONFIG_PM_SLEEP is not set

When CONFIG_PM_SLEEP is not defined compiler complain as follow:
CC [M] drivers/net/ethernet/intel/e1000e/netdev.o
drivers/net/ethernet/intel/e1000e/netdev.c:6302:12: warning: ‘e1000e_s0ix_entry_flow’ defined but not used [-Wunused-function]
static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)
drivers/net/ethernet/intel/e1000e/netdev.c:6411:12: warning: ‘e1000e_s0ix_exit_flow’ defined but not used [-Wunused-function]
static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)
LD [M] drivers/net/ethernet/intel/e1000e/e1000e.o

Add wrap to fix these warnings.

Reported-by: kbuild test robot <lpk@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Add support for Tiger Lake

Add devices ID's for the next LOM generations that will be
available on the next Intel Client platform (Tiger Lake)
This patch provides the initial support for these devices

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Drop unnecessary __E1000_DOWN bit twiddling

Since we no longer check for __E1000_DOWN in e1000e_close we can drop the
spot where we were restoring the bit. This saves us a bit of unnecessary
complexity.

Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Use rtnl_lock to prevent race conditions between net and pci/pm

This patch is meant to address possible race conditions that can exist
between network configuration and power management. A similar issue was
fixed for igb in commit 9474933caf21 ("igb: close/suspend race in
netif_device_detach").

In addition it consolidates the code so that the PCI error handling code
will essentially perform the power management freeze on the device prior to
attempting a reset, and will thaw the device afterwards if that is what it
is planning to do. Otherwise when we call close on the interface it should
see it is detached and not attempt to call the logic to down the interface
and free the IRQs again.

From what I can tell the check that was adding the check for __E1000_DOWN
in e1000e_close was added when runtime power management was added. However
it should not be relevant for us as we perform a call to
pm_runtime_get_sync before we call e1000_down/free_irq so it should always
be back up before we call into this anyway.

Reported-by: Morumuri Srivalli <smorumu1@in.ibm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: David Dai <zdai@linux.vnet.ibm.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>

e1000e: Add support for Comet Lake

Add devices ID's for the next LOM generations that will be
available on the next Intel Client platform (Comet Lake)
This patch provides the initial support for these devices

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Add support for S0ix

Implement flow for S0ix support. Modern SoCs support S0ix low power
states during idle periods, which are sub-states of ACPI S0 that increase
power saving while supporting an instant-on experience for providing
lower latency that ACPI S0. The S0ix states shut off parts of the SoC
when they are not in use, while still maintaning optimal performance.
This patch add support for S0ix started from an Ice Lake platform.

Suggested-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Make speed detection on hotplugging cable more reliable

After hot plugging an 1Gbps Ethernet cable with 1Gbps link partner, the
MII_BMSR may report 10Mbps, renders the network rather slow.

The issue has much lower fail rate after commit 59653e6497d1 ("e1000e:
Make watchdog use delayed work"), which essentially introduces some
delay before running the watchdog task.

But there's still a chance that the hot plugging event and the queued
watchdog task gets run at the same time, then the original issue can be
observed once again.

So let's use mod_delayed_work() to add a deterministic 1 second delay
before running watchdog task, after an interrupt.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Use dev_get_drvdata where possible

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Use skb accessors in network drivers

In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.

Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: PCIm function state support

Due to commit: 5d8682588605 ("[misc] mei: me: allow runtime
pm for platform with D0i3")
When disconnecting the cable and reconnecting it the NIC
enters DMoff state. This caused wrong link indication
and duplex mismatch. This bug is described in:
https://bugzilla.redhat.com/show_bug.cgi?id=1689436

Checking PCIm function state and performing PHY reset after a
timeout in watchdog task solves this issue.

Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Make watchdog use delayed work

Use delayed work instead of timers to run the watchdog of the e1000e
driver.

Simplify the code with one less middle function.

Signed-off-by: Detlev Casanova <detlev.casanova@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Reduce boot time by tightening sleep ranges

The e1000e driver is a great user of the usleep_range() API,
and has nice ranges that in principle help power management.

However the ranges that are used only during system startup are
very long (and can add easily 100 msec to the boot time) while
the power savings of such long ranges is irrelevant due to the
one-off, boot only, nature of these functions.

This patch shrinks some of the longest ranges to be shorter
(while still using a power friendly 1 msec range); this saves
100msec+ of boot time on my BDW NUCs

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Increase pause and refresh time

Suggested-by: Tim Pepper <timothy.c.pepper@linux.intel.com>
Signed-off-by: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: start network tx queue only when link is up

Driver does not want to keep packets in Tx queue when link is lost.
But present code only reset NIC to flush them, but does not prevent
queuing new packets. Moreover reset sequence itself could generate
new packets via netconsole and NIC falls into endless reset loop.

This patch wakes Tx queue only when NIC is ready to send packets.

This is proper fix for problem addressed by commit 0f9e980bf5ee
("e1000e: fix cyclic resets at link up with active tx").

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Revert "e1000e: fix cyclic resets at link up with active tx"

This reverts commit 0f9e980bf5ee1a97e2e401c846b2af989eb21c61.

That change cased false-positive warning about hardware hang:

e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
e1000e 0000:00:1f.6 eth0: Detected Hardware Unit Hang:
TDH <0>
TDT <1>
next_to_use <1>
next_to_clean <0>
buffer_info[next_to_clean]:
time_stamp <fffba7a7>
next_to_watch <0>
jiffies <fffbb140>
next_to_watch.status <0>
MAC Status <40080080>
PHY Status <7949>
PHY 1000BASE-T Status <0>
PHY Extended Status <3000>
PCI Status <10>
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx

Besides warning everything works fine.
Original issue will be fixed property in following patch.

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Joseph Yasi <joe.yasi@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203175
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers: Remove explicit invocations of mmiowb()

mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:

@mmiowb@
@@
- mmiowb();

and invoked as:

$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done

NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

net: move skb->xmit_more hint to softnet data

There are two reasons for this.

First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.

Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().

We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.

Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.

skb->xmit_more is retained (but always 0) to not cause build breakage.

This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions. Remaining drivers are converted in the next patches.

Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Disable runtime PM on CNP+

There are some new e1000e devices can only be woken up from D3 one time,
by plugging Ethernet cable. Subsequent cable plugging does set PME bit
correctly, but it still doesn't get woken up.

Since e1000e connects to the root complex directly, we rely on ACPI to
wake it up. In this case, the GPE from _PRW only works once and stops
working after that. Though it appears to be a platform bug, e1000e
maintainers confirmed that I219 does not support D3.

So disable runtime PM on CNP+ chips. We may need to disable earlier
generations if this bug also hit older platforms.

Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=280819
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

intel: correct return from set features callback

According to comments in <linux/netdevice.h> we should return either >0
or -errno from ->ndo_set_features() if changing dev->features by itself.

Return 1 in such places to notify netdev_update_features() about applied
changes in dev->features.

Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix -Wformat-truncation warnings

Provide precision hints to snprintf() since we know the destination
buffer size of the RX/TX ring names are IFNAMSIZ + 5 - 1. This fixes the
following warnings:

drivers/net/ethernet/intel/e1000e/netdev.c: In function
'e1000_request_msix':
drivers/net/ethernet/intel/e1000e/netdev.c:2109:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-rx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2107:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->rx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->rx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-rx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/e1000e/netdev.c:2125:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-tx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2123:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->tx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->tx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-tx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: fix cyclic resets at link up with active tx

I'm seeing series of e1000e resets (sometimes endless) at system boot
if something generates tx traffic at this time. In my case this is
netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states
have been disabled in order to enable jumbo frames" from e1000e itself.
As result e1000_watchdog_task sees used tx buffer while carrier is off
and start this reset cycle again.

[ 17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000
[ 23.033336] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 27.174495] 8021q: 802.1Q VLAN Support v1.8
[ 27.174513] 8021q: adding VLAN 0 to HW filter on device eth1
[ 30.671724] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
[ 30.898564] netpoll: netconsole: local port 6666
[ 30.898566] netpoll: netconsole: local IPv6 address 2a02:6b8:0:80b:beae:c5ff:fe28:23f8
[ 30.898567] netpoll: netconsole: interface 'eth1'
[ 30.898568] netpoll: netconsole: remote port 6666
[ 30.898568] netpoll: netconsole: remote IPv6 address 2a02:6b8:b000:605c:e61d:2dff:fe03:3790
[ 30.898569] netpoll: netconsole: remote ethernet address b0:a8:6e:f4:ff:c0
[ 30.917747] console [netcon0] enabled
[ 30.917749] netconsole: network logging started
[ 31.453353] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.185730] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.321840] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.465822] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.597423] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.745417] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.877356] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.005441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.157376] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.289362] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.417441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None

This patch flushes tx buffers only once when carrier is off
rather than at each watchdog iteration.

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Exclude device from suspend direct complete optimization

e1000e sets different WoL settings in system suspend callback and
runtime suspend callback.

The suspend direct complete optimization leaves e1000e in runtime
suspended state with wrong WoL setting during system suspend.

To fix this, we need to disable suspend direct complete optimization to
let e1000e always use suspend callback to set correct WoL during system
suspend.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

cross-tree: phase out dma_zalloc_coherent()

We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.

This change was generated with the following Coccinelle SmPL patch:

@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@

-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)

Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>

ethernet/intel: consolidate NAPI and NAPI exit

While reviewing code, I noticed that Eric Dumazet recommends that
drivers check the return code of napi_complete_done, and use that
to decide to enable interrupts or not when exiting poll. One of
the Intel drivers was already fixed (ixgbe).

Upon looking at the Intel drivers as a whole, we are handling our
polling and NAPI exit in a few different ways based on whether we
have multiqueue and whether we have Tx cleanup included. Several
drivers had the bug of exiting NAPI with return 0, which appears
to mess up the accounting in the stack.

Consolidate all the NAPI routines to do best known way of exiting
and to just mostly look like each other.
1) check return code of napi_complete_done to control interrupt enable
2) return the actual amount of work done.
3) return budget immediately if need NAPI poll again

Tested the changes on e1000e with a high interrupt rate set, and
it shows about an 8% reduction in the CPU utilization when busy
polling because we aren't re-enabling interrupts when we're about
to be polled.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: extend PTP gettime function to read system clock

This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.

Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI/AER: Remove pci_cleanup_aer_uncorrect_error_status() calls

After bfcb79fca19d ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.

Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.

Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

intel-ethernet: use correct module license

We recently updated all our SPDX identifiers to correctly
indicate our net/ethernet/intel/* drivers were always released
and intended to be released under GPL v2, but the MODULE_LICENSE
declaration was never updated.

Fix the MODULE_LICENSE to be GPL v2, for all our drivers.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

treewide: kzalloc() -> kcalloc()

The kzalloc() function has a 2-factor argument form, kcalloc(). This
patch replaces cases of:

kzalloc(a * b, gfp)

with:
kcalloc(a * b, gfp)

as well as handling cases of:

kzalloc(a * b * c, gfp)

with:

kzalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

kzalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

kzalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
kzalloc(
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
kzalloc(
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
kzalloc(
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(char) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kzalloc
+ kcalloc
(
- SIZE * COUNT
+ COUNT, SIZE
, ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
kzalloc(
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
kzalloc(
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kzalloc(
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
kzalloc(
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
kzalloc(C1 * C2 * C3, ...)
|
kzalloc(
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
kzalloc(sizeof(THING) * C2, ...)
|
kzalloc(sizeof(TYPE) * C2, ...)
|
kzalloc(C1 * C2 * C3, ...)
|
kzalloc(C1 * C2, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- (E1) * E2
+ E1, E2
, ...)
|
- kzalloc
+ kcalloc
(
- (E1) * (E2)
+ E1, E2
, ...)
|
- kzalloc
+ kcalloc
(
- E1 * E2
+ E1, E2
, ...)
)

Signed-off-by: Kees Cook <keescook@chromium.org>

e1000e: Ignore TSYNCRXCTL when getting I219 clock attributes

There have been multiple reports of crashes that look like
kernel: RIP: 0010:[<ffffffff8110303f>] timecounter_read+0xf/0x50
[...]
kernel: Call Trace:
kernel: [<ffffffffa0806b0f>] e1000e_phc_gettime+0x2f/0x60 [e1000e]
kernel: [<ffffffffa0806c5d>] e1000e_systim_overflow_work+0x1d/0x80 [e1000e]
kernel: [<ffffffff810992c5>] process_one_work+0x155/0x440
kernel: [<ffffffff81099e16>] worker_thread+0x116/0x4b0
kernel: [<ffffffff8109f422>] kthread+0xd2/0xf0
kernel: [<ffffffff8163184f>] ret_from_fork+0x3f/0x70

These can be traced back to the fact that e1000e_systim_reset() skips the
timecounter_init() call if e1000e_get_base_timinca() returns -EINVAL, which
leads to a null deref in timecounter_read().

Commit 83129b37ef35 ("e1000e: fix systim issues", v4.2-rc1) reworked
e1000e_get_base_timinca() in such a way that it can return -EINVAL for
e1000_pch_spt if the SYSCFI bit is not set in TSYNCRXCTL.

Some experimentation has shown that on I219 (e1000_pch_spt, "MAC: 12")
adapters, the E1000_TSYNCRXCTL_SYSCFI flag is unstable; TSYNCRXCTL reads
sometimes don't have the SYSCFI bit set. Retrying the read shortly after
finds the bit to be set. This was observed at boot (probe) but also link up
and link down.

Moreover, the phc (PTP Hardware Clock) seems to operate normally even after
reads where SYSCFI=0. Therefore, remove this register read and
unconditionally set the clock parameters.

Reported-by: Achim Mildenberger <admin@fph.physik.uni-karlsruhe.de>
Message-Id: <20180425065243.g5mqewg5irkwgwgv@f2>
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1075876
Fixes: 83129b37ef35 ("e1000e: fix systim issues")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net: intel: Cleanup the copyright/license headers

After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.

Also caught a few files missing the SPDX license identifier, so fixed
them up.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

intel: add SPDX identifiers to all the Intel drivers

Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "e1000e: Separate signaling for link check/link up"

This reverts commit 19110cfbb34d4af0cdfe14cd243f3b09dc95b013.
This reverts commit 4110e02eb45ea447ec6f5459c9934de0a273fb91.
This reverts commit d3604515c9eda464a92e8e67aae82dfe07fe3c98.

Commit 19110cfbb34d ("e1000e: Separate signaling for link check/link up")
changed what happens to the link status when there is an error which
happens after "get_link_status = false" in the copper check_for_link
callbacks. Previously, such an error would be ignored and the link
considered up. After that commit, any error implies that the link is down.

Revert commit 19110cfbb34d ("e1000e: Separate signaling for link check/link
up") and its followups. After reverting, the race condition described in
the log of commit 19110cfbb34d is reintroduced. It may still be triggered
by LSC events but this should keep the link down in case the link is
electrically unstable, as discussed. The race may no longer be
triggered by RXO events because commit 4aea7a5c5e94 ("e1000e: Avoid
receiver overrun interrupt bursts") restored reading icr in the Other
handler.

Link: https://lkml.org/lkml/2018/3/1/789
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: allocate ring descriptors with dma_zalloc_coherent

Descriptor rings were not initialized at zero when allocated
When area contained garbage data, it caused skb_over_panic in
e1000_clean_rx_irq (if data had E1000_RXD_STAT_DD bit set)

This patch makes use of dma_zalloc_coherent to make sure the
ring is memset at 0 to prevent the area from containing garbage.

Following is the signature of the panic:
IODDR0@0.0: skbuff: skb_over_panic: text:80407b20 len:64010 put:64010 head:ab46d800 data:ab46d842 tail:0xab47d24c end:0xab46df40 dev:eth0
IODDR0@0.0: BUG: failure at net/core/skbuff.c:105/skb_panic()!
IODDR0@0.0: Kernel panic - not syncing: BUG!
IODDR0@0.0:
IODDR0@0.0: Process swapper/0 (pid: 0, threadinfo=81728000, task=8173cc00 ,cpu: 0)
IODDR0@0.0: SP = <815a1c0c>
IODDR0@0.0: Stack: 00000001
IODDR0@0.0: b2d89800 815e33ac
IODDR0@0.0: ea73c040 00000001
IODDR0@0.0: 60040003 0000fa0a
IODDR0@0.0: 00000002
IODDR0@0.0:
IODDR0@0.0: 804540c0 815a1c70
IODDR0@0.0: b2744000 602ac070
IODDR0@0.0: 815a1c44 b2d89800
IODDR0@0.0: 8173cc00 815a1c08
IODDR0@0.0:
IODDR0@0.0: 00000006
IODDR0@0.0: 815a1b50 00000000
IODDR0@0.0: 80079434 00000001
IODDR0@0.0: ab46df40 b2744000
IODDR0@0.0: b2d89800
IODDR0@0.0:
IODDR0@0.0: 0000fa0a 8045745c
IODDR0@0.0: 815a1c88 0000fa0a
IODDR0@0.0: 80407b20 b2789f80
IODDR0@0.0: 00000005 80407b20
IODDR0@0.0:
IODDR0@0.0:
IODDR0@0.0: Call Trace:
IODDR0@0.0: [<804540bc>] skb_panic+0xa4/0xa8
IODDR0@0.0: [<80079430>] console_unlock+0x2f8/0x6d0
IODDR0@0.0: [<80457458>] skb_put+0xa0/0xc0
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<804079c8>] e1000_clean_rx_irq+0x188/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80468b48>] __dev_kfree_skb_any+0x88/0xa8
IODDR0@0.0: [<804101ac>] e1000e_poll+0x94/0x288
IODDR0@0.0: [<8046e9d4>] net_rx_action+0x19c/0x4e8
IODDR0@0.0: ...
IODDR0@0.0: Maximum depth to print reached. Use kstack=<maximum_depth_to_print> To specify a custom value (where 0 means to display the full backtrace)
IODDR0@0.0: ---[ end Kernel panic - not syncing: BUG!

Signed-off-by: Pierre-Yves Kerbrat <pkerbrat@kalray.eu>
Signed-off-by: Marius Gligor <mgligor@kalray.eu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Avoid missed interrupts following ICR read

The 82574 specification update errata 12 states that interrupts may be
missed if ICR is read while INT_ASSERTED is not set. Avoid that problem by
setting all bits related to events that can trigger the Other interrupt in
IMS.

The Other interrupt is raised for such events regardless of whether or not
they are set in IMS. However, only when they are set is the INT_ASSERTED
bit also set in ICR.

By doing this, we ensure that INT_ASSERTED is always set when we read ICR
in e1000_msix_other() and steer clear of the errata. This also ensures that
ICR will automatically be cleared on read, therefore we no longer need to
clear bits explicitly.

Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix queue interrupt re-raising in Other interrupt

Restores the ICS write for Rx/Tx queue interrupts which was present before
commit 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1)
but was not restored in commit 4aea7a5c5e94
("e1000e: Avoid receiver overrun interrupt bursts", v4.15-rc1).

This re-raises the queue interrupts in case the txq or rxq bits were set in
ICR and the Other interrupt handler read and cleared ICR before the queue
interrupt was raised.

Fixes: 4aea7a5c5e94 ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Partial revert "e1000e: Avoid receiver overrun interrupt bursts"

This partially reverts commit 4aea7a5c5e940c1723add439f4088844cd26196d.

We keep the fix for the first part of the problem (1) described in the log
of that commit, that is to read ICR in the other interrupt handler. We
remove the fix for the second part of the problem (2), Other interrupt
throttling.

Bursts of "Other" interrupts may once again occur during rxo (receive
overflow) traffic conditions. This is deemed acceptable in the interest of
avoiding unforeseen fallout from changes that are not strictly necessary.
As discussed, the e1000e driver should be in "maintenance mode".

Link: https://www.spinics.net/lists/netdev/msg480675.html
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Remove Other from EIAC

It was reported that emulated e1000e devices in vmware esxi 6.5 Build
7526125 do not link up after commit 4aea7a5c5e94 ("e1000e: Avoid receiver
overrun interrupt bursts", v4.15-rc1). Some tracing shows that after
e1000e_trigger_lsc() is called, ICR reads out as 0x0 in e1000_msix_other()
on emulated e1000e devices. In comparison, on real e1000e 82574 hardware,
icr=0x80000004 (_INT_ASSERTED | _LSC) in the same situation.

Some experimentation showed that this flaw in vmware e1000e emulation can
be worked around by not setting Other in EIAC. This is how it was before
16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1).

Fixes: 4aea7a5c5e94 ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Alert the user that C-states will be disabled by enabling jumbo frames

I personally spent a long time trying to decypher why my CPU would not
reach deeper C-states. Let's just tell the next user what's going on.

Signed-off-by: Matt Turner <matt.turner@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Set HTHRESH when PTHRESH is used

According to section 12.0.3.4.13 "Receive Descriptor Control - RXDCTL"
of the Intel® 82579 Gigabit Ethernet PHY Datasheet v2.1:

"HTHRESH should be given a non zero value when ever PTHRESH is
used."

In RXDCTL(0), PTHRESH lives at bits 5:0, and HTHREST lives at bits 13:8.
Set only bit 8 of HTHREST as is done in e1000_flush_rx_ring(). Found by
inspection.

Signed-off-by: Matt Turner <matt.turner@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix the use of magic numbers for buffer overrun issue

This is a follow on to commit b10effb92e27 ("fix buffer overrun while the
I219 is processing DMA transactions") to address David Laights concerns
about the use of "magic" numbers. So define masks as well as add
additional code comments to give a better understanding of what needs to
be done to avoid a buffer overrun.

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Alexander H Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ethernet/intel: Convert timers to use timer_setup()

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Be drop monitor friendly

e1000e_put_txbuf() can be called from normal reclamation path as well as
when a DMA mapping failure, so we need to differentiate these two cases
when freeing SKBs to be drop monitor friendly. e1000e_tx_hwtstamp_work()
and e1000_remove() are processing TX timestamped SKBs and those should
not be accounted as drops either.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: apply burst mode settings only on default

Devices that support FLAG2_DMA_BURST have different default values
for RDTR and RADV. Apply burst mode default settings only when no
explicit value was passed at module load.

The RDTR default is zero. If the module is loaded for low latency
operation with RxIntDelay=0, do not override this value with a burst
default of 32.

Move the decision to apply burst values earlier, where explicitly
initialized module variables can be distinguished from defaults.

Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix buffer overrun while the I219 is processing DMA transactions

Intel® 100/200 Series Chipset platforms reduced the round-trip
latency for the LAN Controller DMA accesses, causing in some high
performance cases a buffer overrun while the I219 LAN Connected
Device is processing the DMA transactions. I219LM and I219V devices
can fall into unrecovered Tx hang under very stressfully UDP traffic
and multiple reconnection of Ethernet cable. This Tx hang of the LAN
Controller is only recovered if the system is rebooted. Slightly slow
down DMA access by reducing the number of outstanding requests.
This workaround could have an impact on TCP traffic performance
on the platform. Disabling TSO eliminates performance loss for TCP
traffic without a noticeable impact on CPU performance.

Please, refer to I218/I219 specification update:
https://www.intel.com/content/www/us/en/embedded/products/networking/
ethernet-connection-i218-family-documentation.html

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Avoid receiver overrun interrupt bursts

When e1000e_poll() is not fast enough to keep up with incoming traffic, the
adapter (when operating in msix mode) raises the Other interrupt to signal
Receiver Overrun.

This is a double problem because 1) at the moment e1000_msix_other()
assumes that it is only called in case of Link Status Change and 2) if the
condition persists, the interrupt is repeatedly raised again in quick
succession.

Ideally we would configure the Other interrupt to not be raised in case of
receiver overrun but this doesn't seem possible on this adapter. Instead,
we handle the first part of the problem by reverting to the practice of
reading ICR in the other interrupt handler, like before commit 16ecba59bc33
("e1000e: Do not read ICR in Other interrupt"). Thanks to commit
0a8047ac68e5 ("e1000e: Fix msi-x interrupt automask") which cleared IAME
from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts
anymore. We handle the second part of the problem by not re-enabling the
Other interrupt right away when there is overrun. Instead, we wait until
traffic subsides, napi polling mode is exited and interrupts are
re-enabled.

Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Fixes: 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Separate signaling for link check/link up

Lennart reported the following race condition:

\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
/* link is up */
mac->get_link_status = false;

/* interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true;

link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */

This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.

Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().

Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix return value test

All the helpers return -E1000_ERR_PHY.

Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix wrong comment related to link detection

Reading e1000e_check_for_copper_link() shows that get_link_status is set to
false after link has been detected. Therefore, it stays TRUE until then.

Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers: net: e1000e: use setup_timer() helper.

Use setup_timer function instead of initializing timer with the
function and data fields.

Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Initial Support for IceLake

i219 (8) and i219 (9) are the next LOM generations that will be available
on the next Intel Client platform (IceLake).
This patch provides the initial support for these devices

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Undo e1000e_pm_freeze if __e1000_shutdown fails

An error during suspend (e100e_pm_suspend),

[ 429.994338] ACPI : EC: event blocked
[ 429.994633] e1000e: EEE TX LPI TIMER: 00000011
[ 430.955451] pci_pm_suspend(): e1000e_pm_suspend+0x0/0x30 [e1000e] returns -2
[ 430.955454] dpm_run_callback(): pci_pm_suspend+0x0/0x140 returns -2
[ 430.955458] PM: Device 0000:00:19.0 failed to suspend async: error -2
[ 430.955581] PM: Some devices failed to suspend, or early wake event detected
[ 430.957709] ACPI : EC: event unblocked

lead to complete failure:

[ 432.585002] ------------[ cut here ]------------
[ 432.585013] WARNING: CPU: 3 PID: 8372 at kernel/irq/manage.c:1478 __free_irq+0x9f/0x280
[ 432.585015] Trying to free already-free IRQ 20
[ 432.585016] Modules linked in: cdc_ncm usbnet x86_pkg_temp_thermal intel_powerclamp coretemp mii crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep lpc_ich snd_hda_core snd_pcm mei_me mei sdhci_pci sdhci i915 mmc_core e1000e ptp pps_core prime_numbers
[ 432.585042] CPU: 3 PID: 8372 Comm: kworker/u16:40 Tainted: G U 4.10.0-rc8-CI-Patchwork_3870+ #1
[ 432.585044] Hardware name: LENOVO 2356GCG/2356GCG, BIOS G7ET31WW (1.13 ) 07/02/2012
[ 432.585050] Workqueue: events_unbound async_run_entry_fn
[ 432.585051] Call Trace:
[ 432.585058] dump_stack+0x67/0x92
[ 432.585062] __warn+0xc6/0xe0
[ 432.585065] warn_slowpath_fmt+0x4a/0x50
[ 432.585070] ? _raw_spin_lock_irqsave+0x49/0x60
[ 432.585072] __free_irq+0x9f/0x280
[ 432.585075] free_irq+0x34/0x80
[ 432.585089] e1000_free_irq+0x65/0x70 [e1000e]
[ 432.585098] e1000e_pm_freeze+0x7a/0xb0 [e1000e]
[ 432.585106] e1000e_pm_suspend+0x21/0x30 [e1000e]
[ 432.585113] pci_pm_suspend+0x71/0x140
[ 432.585118] dpm_run_callback+0x6f/0x330
[ 432.585122] ? pci_pm_freeze+0xe0/0xe0
[ 432.585125] __device_suspend+0xea/0x330
[ 432.585128] async_suspend+0x1a/0x90
[ 432.585132] async_run_entry_fn+0x34/0x160
[ 432.585137] process_one_work+0x1f4/0x6d0
[ 432.585140] ? process_one_work+0x16e/0x6d0
[ 432.585143] worker_thread+0x49/0x4a0
[ 432.585145] kthread+0x107/0x140
[ 432.585148] ? process_one_work+0x6d0/0x6d0
[ 432.585150] ? kthread_create_on_node+0x40/0x40
[ 432.585154] ret_from_fork+0x2e/0x40
[ 432.585156] ---[ end trace 6712df7f8c4b9124 ]---

The unwind failures stems from commit 2800209994f8 ("e1000e: Refactor PM
flows"), but it may be a later patch that introduced the non-recoverable
behaviour.

Fixes: 2800209994f8 ("e1000e: Refactor PM flows")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99847
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: use disable_hardirq() also for MSIX vectors in e1000_netpoll()

Replace disable_irq() which waits for threaded irq handlers with
disable_hardirq() which waits only for hardirq part.

Fixes: 311191297125 ("e1000: use disable_hardirq() for e1000_netpoll()")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: add statistic indicating number of skipped Tx timestamps

The e1000e driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.

There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix race condition around skb_tstamp_tx()

The e1000e driver and related hardware has a limitation on Tx PTP
packets which requires we limit to timestamping a single packet at once.
We do this by verifying that we never request a new Tx timestamp while
we still have a tx_hwtstamp_skb pointer.

Unfortunately the driver suffers from a race condition around this. The
tx_hwtstamp_skb pointer is not set to NULL until after skb_tstamp_tx()
is called. This function notifies the stack and applications of a new
timestamp. Even a well behaved application that only sends a new request
when the first one is finished might be woken up and possibly send
a packet before we can free the timestamp in the driver again. The
result is that we needlessly ignore some Tx timestamp requests in this
corner case.

Fix this by assigning the tx_hwtstamp_skb pointer prior to calling
skb_tstamp_tx() and use a temporary pointer to hold the timestamped skb
until that function finishes. This ensures that the application is not
woken up until the driver is ready to begin timestamping a new packet.

This ensures that well behaved applications do not accidentally race
with condition to skip Tx timestamps. Obviously an application which
sends multiple Tx timestamp requests at once will still only timestamp
one packet at a time. Unfortunately there is nothing we can do about
this.

Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net: ethernet: update drivers to make both SW and HW TX timestamps

Some drivers were calling the skb_tx_timestamp() function only when
a hardware timestamp was not requested. Now that applications can use
the SOF_TIMESTAMPING_OPT_TX_SWHW option to request both software and
hardware timestamps, the drivers need to be modified to unconditionally
call skb_tx_timestamp().

CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: update drivers to handle HWTSTAMP_FILTER_NTP_ALL

Include HWTSTAMP_FILTER_NTP_ALL in net_hwtstamp_validate() as a valid
filter and update drivers which can timestamp all packets, or which
explicitly list unsupported filters instead of using a default case, to
handle the filter.

CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Add Support for 38.4MHZ frequency

Add support for 38.4MHz frequency is required for PTP
on CannonLake. SYSTIM frequency adjustment attributes for TIMINCA are
get/set dependent on the hardware clock frequency for a different
types of adapters. 38.4MHz frequency supported by CannonLake
and active once time synchronisation mechanism was enabled
Changed abbreviation from Hz to HZ to be compliant checkpatch code style

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Add Support for CannonLake

The propagation of CannonLake mac type to driver functionality

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Initial Support for CannonLake

i219 (6) and i219 (7) are the next LOM generations that will be
available on the nextIntel Client platform (CannonLake)
This patch provides the initial support for these devices

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix timing for 82579 Gigabit Ethernet controller

After an upgrade to Linux kernel v4.x the hardware timestamps of the
82579 Gigabit Ethernet Controller are different than expected.
The values that are being read are almost four times as big as before
the kernel upgrade.

The difference is that after the upgrade the driver sets the clock
frequency to 25MHz, where before the upgrade it was set to 96MHz. Intel
confirmed that the correct frequency for this network adapter is 96MHz.

Signed-off-by: Bernd Faust <berndfaust@gmail.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Revert "e1000e: driver trying to free already-free irq"

This reverts commit 7e54d9d063fa239c95c21548c5267f0ef419ff56.

After additional regression testing, several users are experiencing
kernel panics during shutdown on e1000e devices. Reverting this
change resolves the issue.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Remove usage of net_device last_rx member

The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f242738376d ("bonding: use last_arp_rx in slave_last_rx()").

However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.

Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f49b ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dacec ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.

Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.

Compile-tested with allyesconfig and allmodconfig on x86 and arm.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: remove useless memset's in drivers get_stats64

In dev_get_stats() the statistic structure storage has already been
zeroed. Therefore network drivers do not need to call memset() again.

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: make ndo_get_stats64 a void function

The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.

Fix all drivers with ndo_get_stats64 to have a void function.

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: driver trying to free already-free irq

During systemd reboot sequence network driver interface is shutdown
by e1000_close. The PCI driver interface is shut by e1000_shutdown.
The e1000_shutdown checks for netif_running status, if still up it
brings down driver. But it disables msi outside of this if statement,
regardless of netif status. All this is OK when e1000_close happens
after shutdown. However, by default, everything in systemd is done
in parallel. This creates a conditions where e1000_shutdown is called
after e1000_close, therefore hitting BUG_ON assert in free_msi_irqs.

CC: xe-kernel@external.cisco.com
Signed-off-by: khalidm <khalidm@cisco.com>
Signed-off-by: David Singleton <davsingl@cisco.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

clocksource: Use a plain u64 instead of cycle_t

There is no point in having an extra type for extra confusion. u64 is
unambiguous.

Conversion was done with the following coccinelle script:

@rem@
@@
-typedef u64 cycle_t;

@fix@
typedef cycle_t;
@@
-cycle_t
+u64

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>

e1000: use disable_hardirq() for e1000_netpoll()

In commit 02cea3958664 ("genirq: Provide disable_hardirq()")
Peter introduced disable_hardirq() for netpoll, but it is forgotten
to use it for e1000.

This patch changes disable_irq() to disable_hardirq() for e1000.

Reported-by: Dave Jones <davej@codemonkey.org.uk>
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet/intel: use core min/max MTU checking

e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
and no longer serves a purpose. No need to set min_mtu or max_mtu
explicitly, as ether_setup() will already set them to 68 and 1500.

e1000: min_mtu 46, max_mtu 16110

e1000e: min_mtu 68, max_mtu varies based on adapter

fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now

i40e: min_mtu 68, max_mtu 9706

i40evf: min_mtu 68, max_mtu 9706

igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
the driver, the larger value wasn't relevant though, so I've set max_mtu
to the smaller of the two values here to retain identical behavior.

igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated

ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu

ixgbe: min_mtu 68, max_mtu 9710

ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710

CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: factor out systim sanitization

This is prepatory work for an expanding list of adapter families that have
occasional ~10 hour clock jumps when being used for PTP. Factor out the
sanitization function and convert to using a feature (bug) flag, per
suggestion from Jesse Brandeburg.

Littering functional code with device-specific checks is much messier than
simply checking a flag, and having device-specific init set flags as needed.
There are probably a number of other cases in the e1000e code that
could/should be converted similarly.

Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: prevent division by zero if TIMINCA is zero

Users report that under VMWare, er32(TIMINCA) returns zero.
This causes division by zero at init time as follows:

==> incvalue = er32(TIMINCA) & E1000_TIMINCA_INCVALUE_MASK;
for (i = 0; i < E1000_MAX_82574_SYSTIM_REREADS; i++) {
/* latch SYSTIMH on read of SYSTIML */
systim_next = (cycle_t)er32(SYSTIML);
systim_next |= (cycle_t)er32(SYSTIMH) << 32;

time_delta = systim_next - systim;
temp = time_delta;
====> rem = do_div(temp, incvalue);

This change makes kernel survive this, and users report that
NIC does work after this change.

Since on real hardware incvalue is never zero, this should not affect
real hardware use case.

Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: keep Rx/Tx HW_VLAN_CTAG in sync

The bit in the e1000 driver that mentions explicitly that the hardware
has no support for separate RX/TX VLAN accel toggling rings true for
e1000e as well, and thus both NETIF_F_HW_VLAN_CTAG_RX and
NETIF_F_HW_VLAN_CTAG_TX need to be kept in sync.

Revert a portion of commit 889ad456660461 ("e1000e: keep VLAN interfaces
functional after rxvlan off") since keeping the bits in sync resolves
the original issue.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: keep VLAN interfaces functional after rxvlan off

I've got a bug report about an e1000e interface, where a VLAN interface is
set up on top of it:

$ ip link add link ens1f0 name ens1f0.99 type vlan id 99
$ ip link set ens1f0 up
$ ip link set ens1f0.99 up
$ ip addr add 192.168.99.92 dev ens1f0.99

At this point, I can ping another host on vlan 99, ip 192.168.99.91.
However, if I do the following:

$ ethtool -K ens1f0 rxvlan off

Then no traffic passes on ens1f0.99. It comes back if I toggle rxvlan on
again. I'm not sure if this is actually intended behavior, or if there's a
lack of software VLAN stripping fallback, or what, but things continue to
work if I simply don't call e1000e_vlan_strip_disable() if there are
active VLANs (plagiarizing a function from the e1000 driver here) on the
interface.

Also slipped a related-ish fix to the kerneldoc text for
e1000e_vlan_strip_disable here...

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet/intel: Use pci_(request|release)_mem_regions

Now that we do have pci_request_mem_regions() and pci_release_mem_regions()
at hand, use it in the Intel ethernet drivers.

Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: David S. Miller <davem@davemloft.net>

e1000e: don't modify SYSTIM registers during SIOCSHWTSTAMP ioctl

The e1000e_config_hwtstamp function was incorrectly resetting the SYSTIM
registers every time the ioctl was being run. If you happened to be
running ptp4l and lost the PTP connect (removing cable, or blocking the
UDP traffic for example), then ptp4l will eventually perform a restart
which involves re-requesting timestamp settings. In e1000e this has the
unfortunate and incorrect result of resetting SYSTIME to the kernel
time. Since kernel time is usually in UTC, and PTP time is in TAI, this
results in the leap second being re-applied.

Fix this by extracting the SYSTIME reset out into its own function,
e1000e_ptp_reset, which we call during reset to restore the hardware
registers. This function will (a) restart the timecounter based on the
new system time, (b) restore the previous PPB setting, and (c) restore
the previous hwtstamp settings.

In order to perform (b), I had to modify the adjfreq ptp function
pointer to store the old delta each time it is called. This also has the
side effect of restoring the correct base timinca register correctly.
The driver does not need to explicitly zero the ptp_delta variable since
the entire adapter structure comes zero-initialized.

Reported-by: Brian Walsh <brian@walsh.ws>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: use BIT() macro for bit defines

This prevents signed bitshift issues when the shift would overwrite the
signed bit, and prevents making this mistake in the future when copying
and modifying code.

Use GENMASK or the unsigned postfix for cases which aren't suitable for
BIT() macro.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: e1000e_cyclecounter_read(): do overflow check only if needed

SYSTIMH:SYSTIML registers are incremented by 24-bit value TIMINCA[23..0]

er32(SYSTIML) are probably moderately expensive (they are pci bus reads).
Can we avoid one of them? Yes, we can.

If the SYSTIML value we see is smaller than 0xff000000, the overflow
into SYSTIMH would require at least two increments.

We do two reads, er32(SYSTIML) and er32(SYSTIMH), in this order.

Even if one increment happens between them, the overflow into SYSTIMH
is impossible, and we can avoid doing another er32(SYSTIML) read
and overflow check.

Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: e1000e_cyclecounter_read(): fix er32(SYSTIML) overflow check

If two consecutive reads of the counter are the same, it is also
not an overflow. "systimel_1 < systimel_2" should be
"systimel_1 <= systimel_2".

Before the patch, we could perform an *erroneous* correction:

Let's say that systimel_1 == systimel_2 == 0xffffffff.
"systimel_1 < systimel_2" is false, we think it's an overflow,
we read "systimeh = er32(SYSTIMH)" which meanwhile had incremented,
and use "(systimeh << 32) + systimel_2" value which is 2^32 too large.

Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: intel-wired-lan@lists.osuosl.org
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: e1000e_cyclecounter_read(): incvalue is 32 bits, not 64

"incvalue" variable holds a result of "er32(TIMINCA) &
E1000_TIMINCA_INCVALUE_MASK" and used in "do_div(temp, incvalue)"
as a divisor.

Thus, "u64 incvalue" declaration is probably a mistake.
Even though it seems to be a harmless one, let's fix it.

Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Cleanup consistency in ret_val variable usage

Fixed the file to use a consistent ret_val for return value checking.

Signed-off-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers: replace dev->trans_start accesses with dev_trans_start

a trans_start struct member exists twice:
- in struct net_device (legacy)
- in struct netdev_queue

Instead of open-coding dev->trans_start usage to obtain the current
trans_start value, use dev_trans_start() instead.

This is not exactly the same, as dev_trans_start also considers
the trans_start values of the netdev queues owned by the device
and provides the most recent one.

For legacy devices this doesn't matter as dev_trans_start can cope
with netdev trans_start values of 0 (they are ignored).

This is a prerequisite to eventual removal of dev->trans_start.

Cc: linux-rdma@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: call ndo_stop() instead of dev_close() when running offline selftest

Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.

Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Initial support for KabeLake

i219 (4) and i219 (5) are the next LOM generations that will be
available on the next Intel platform (KabeLake).
This patch provides the initial support for the devices.

Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix msi-x interrupt automask

Since the introduction of 82574 support in e1000e, the driver has worked
on the assumption that msi-x interrupt generation is automatically
disabled after each irq. As it turns out, this is not the case.
Currently, rx interrupts can fire multiple times before and during napi
processing. This can be a problem for users because frames that arrive
in a certain window (after adapter->clean_rx() but before
napi_complete_done() has cleared NAPI_STATE_SCHED) generate an interrupt
which does not lead to napi_schedule(). These frames sit in the rx queue
until another frame arrives (a tcp retransmit for example).

While the EIAC and CTRL_EXT registers are properly configured for irq
automask, the modification of IAM in e1000_configure_msix() is what
prevents automask from working as intended.

This patch removes that erroneous write and fixes interrupt rearming for
tx interrupts. It also clears IAME from CTRL_EXT. This is not strictly
necessary for operation of the driver but it is to avoid disruption from
potential programs that access the registers directly, like `ethregs -c`.

Reported-by: Frank Steiner <steiner-reg@bio.ifi.lmu.de>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Do not write lsc to ics in msi-x mode

In msi-x mode, there is no handler for the lsc interrupt so there is no
point in writing that to ics now that we always assume Other interrupts
are caused by lsc.

Reviewed-by: Jasna Hodzic <jhodzic@ucdavis.edu>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Do not read ICR in Other interrupt

Removes the ICR read in the other interrupt handler, uses EIAC to
autoclear the Other bit from ICR and IMS. This allows us to avoid
interference with Rx and Tx interrupts in the Other interrupt handler.

The information read from ICR is not needed. IMS is configured such that
the only interrupt cause that can trigger the Other interrupt is Link
Status Change.

Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Remove unreachable code

msi-x interrupts are not shared so there's no need to check if the
interrupt was really from this adapter.

Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Switch e1000e_up to void, drop code checking for error result

The function e1000e_up always returns 0. As such we can convert it to a
void and just ignore the results. This allows us to drop some code in a
couple spots as we no longer need to worry about non-zero return values.

Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: initial support for i219-LM (3)

i219-LM (3) is a LOM that will be available on systems with the
Lewisburg Platform Controller Hub (PCH) chipset from Intel.
This patch provides the initial support for the device.

Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix division by zero on jumbo MTUs

This patch fixes possible division by zero in receive
interrupt handler when working without adaptive interrupt
moderation.

The adaptive interrupt moderation mechanism is typically
disabled on jumbo MTUs.

Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Leonid Bloch <leonid@daynix.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: clean up the local variable

The local variable 'ret' doesn't serve much purpose so we might as well
clean it up.

Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/intel: use napi_complete_done()

As per Eric Dumazet's previous patches:
(see commit (24d2e4a50737) - tg3: use napi_complete_done())

Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout

GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>

Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS

igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589

Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905

MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763

Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816

i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.

Other drivers were only compile tested.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Enable TSO for stacked VLAN

Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with I217-LM.

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Modify Tx/Rx configurations to avoid null pointer dereferences in e1000_open

When e1000e_setup_rx_resources is failed in e1000_open,
e1000e_free_tx_resources in "err_setup_rx" segment is executed.
"writel(0, tx_ring->head)" statement in e1000_clean_tx_ring
in e1000e_free_tx_resources will cause a null poonter dereference(crash),
because "tx_ring->head" is only assigned in e1000_configure_tx
in e1000_configure, but it is after e1000e_setup_rx_resources.

This patch moves head/tail register writing to e1000_configure_tx/rx,
which can fix this problem. It is inspired by igb_configure_tx_ring
in the igb driver.

Specially, thank Alexander Duyck for his valuable suggestion.

Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Increase driver version number

Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix tight loop implementation of systime read algorithm

Change the algorithm. Read systimel twice and check for overflow.
If there was no overflow, use the first value.
If there was an overflow, read systimeh again and use the second
systimel value.

Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix incorrect ASPM locking

This patch fixes wrong locking usage.
In the context of slot reset, we should use lock.
And during resume, there is no need of lock.

Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix EEE in Sx implementation

This patch implements the EEE in Sx code so that it only applies to parts
that support EEE in Sx (as opposed to all parts that support EEE).
It also uses the existing eee_advert and eee_lp_abiliity to set just the
bits (100/1000) that should be set.

Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Cleanup qos request in error handling of e1000_open

The driver lacks pm_qos_remove_request in error handling (err_req_irq) of
e1000_open, and qos request inserted by pm_qos_add_request is not removed.
This patch add pm_qos_remove_request in error handling to fix it.

Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix locking issue with e1000e_disable_aspm

e1000e_disable_aspm called pci_disable_link_state_locked which requires
pci_bus_sem to be held, but is also called from places where this semaphore
was not previously acquired. This patch implements two flavors of
disable_aspm, one that acquires the lock, and the other (_locked) which
should be called when the semaphore is already acquired.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Bump the version to 3.2.5

Bump the version to reflect the driver changes and bug fixes for i219.
Also update the copyright, while we are at it.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix systim issues

Two issues involving systim were reported.
1. Clock is not running in the correct frequency
2. In some situations, systim values were not incremented linearly
This patch fixes the hardware clock configuration and the spurious
non-linear increment.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix legacy interrupt handling in i219

This fix handles a hardware issue that prevented i219 from
working in legacy interrupts mode (IntMode=0)

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix flush_desc_ring implementation

The indication that a descriptor ring flush is required was read from
FEXTNVM7 by mistake. It should be read from the PCI config space.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix logical error in flush_desc_rings

The condition under which the flush should occur was reversed. The fix
should be applied before any HW reset (unless followed by bus reset)
and before any power state transition from D0.

If E1000_FEXTNVM7_NEED_DESCRING_FLUSH bit is set in FEXTNVM7 and TDLEN > 0
the Tx ring should be flushed. (fixes ~95% of the hang states).
If the E1000_FEXTNVM7_NEED_DESCRING_FLUSH did not clear, we should also
flush the RX ring. Bug was caught by Alexander Duyck during a code review
when examining this fix.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: i219 execute unit hang fix on every reset or power state transition

After testing various cases, the conclusion is that the fix MUST be
executed BEFORE any event that the HW is reset or transition to D3.
To fix that I moved the execution to the relevant places but per
Alexander Duyck's review, ensure now that the DMA is valid and was not
freed before manipulating the ring.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: i219 fix unit hang on reset and runtime D3

Unit hang may occur if multiple descriptors are available in the rings
during reset or runtime suspend. This state can be detected by testing
bit 8 in the FEXTNVM7 register. If this bit is set and there are pending
descriptors in one of the rings, we must flush them prior to reset. Same
applies entering runtime suspend.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Do not allow CRC stripping to be disabled on 82579 w/ jumbo frames

The driver wasn't allowing jumbo frames to be
enabled when CRC stripping was disabled, however it was allowing CRC
stripping to be disabled while jumbo frames were enabled. This fixes that by
making it so that the NETIF_F_RXFCS flag cannot be set when jumbo frames are
enabled on 82579 and newer parts.

Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Cleanup handling of VLAN_HLEN as a part of max frame size

When the VLAN_HLEN was added to the calculation for the maximum frame size
there seems to have been a number of issues added to the driver.

The first issue is that in some cases the maximum frame size for a device
never really reached the actual maximum frame size as the VLAN header
length was not included the calculation for that value. As a result some
parts only supported a maximum frame size of either 1496 in the case of
parts that didn't support jumbo frames, and 8996 in the case of the parts
that do.

The second issue is the fact that there were several checks that weren't
updated so as a result setting an MTU of 1500 was treated as enabling jumbo
frames as the calculated value was 1522 instead of 1518. I have addressed
those by replacing ETH_FRAME_LEN with VLAN_ETH_FRAME_LEN where appropriate.

The final issue was the fact that lowering the MTU below 1500 would cause
the driver to allocate 2K buffers for the rings. This is an old issue that
was fixed several years ago in igb/ixgbe and I am addressing now by just
replacing == with a <= so that we always just round up to 1522 for anything
that isn't a jumbo frame.

Fixes: c751a3d58cf2d ("e1000e: Correctly include VLAN_HLEN when changing interface MTU")
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Move pm_qos_req to e1000e adapter

e1000e is the only driver requiring pm_qos_req, instead of causing
every device to waste up to 240 bytes. Allocate it for the specific
driver.

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000, e1000e: Use dma_rmb instead of rmb for descriptor read ordering

This change replaces calls to rmb with dma_rmb in the case where we want to
order all follow-on descriptor reads after the check for the descriptor
status bit.

Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: NVM write protect access removed from SPT HW

The call to e1000e_write_protect_nvm_ich8lan() is no longer supported by HW.
Access to these registers causes a system freeze in A step hardware and is
ignored in B step hardware. This function must not be called in hardware
newer than LPT.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: call netif_carrier_off early on down

When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.

Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.

Move netif_carrier_off as early as possible.

Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: remove calls to ioremap/unmap for NVM addr

Starting I219, the NVM will not be mapped to its own BAR, but to an
address region in another bar. The mapping/unmapping is relevant
to older HW only.

CC: John W Linville <linville@tuxdriver.com>
Reported-by: John W Linville <linville@tuxdriver.com>
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: initial support for i219

i219 is the next-generation LOM that will be available on systems with the
Sunrise Point Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support for the device.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Carmen Edwards <carmenx.edwards@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net: e1000e: support txtd update delay via xmit_more

Don't update Tx tail descriptor if queue hasn't been stopped
and we know at least one more skb will be sent right away.

Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix 82572EI that has no hardware timestamp support

With the Intel 82527EI (driver: e1000e) there is an issue when running
the ptpd2 program, that leads to a kernel oops. The reason is here that
in e1000_xmit_frame() a work queue will be scheduled that has not been
initialized in this case. The work queue "tx_hwstamp_work" will only be
initialized if adapter->flags & FLAG_HAS_HW_TIMESTAMP set. This check
is missing in e1000_xmit_frame().

The following patch adds the missing check.

Signed-off-by: Mathias Koehrer <mathias.koehrer@etas.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net: rename vlan_tx_* helpers since "tx" is misleading there

The same macros are used for rx as well. So rename it.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: convert to CYCLECOUNTER_MASK macro.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Include clocksource.h to get CLOCKSOURCE_MASK.

Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet/intel: Use napi_alloc_skb

This change replaces calls to netdev_alloc_skb_ip_align with
napi_alloc_skb. The advantage of napi_alloc_skb is currently the fact that
the page allocation doesn't make use of any irq disable calls.

There are few spots where I couldn't replace the calls as the buffer
allocation routine is called as a part of init which is outside of the
softirq context.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethernet/intel: Use eth_skb_pad and skb_put_padto helpers

Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.

Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME

After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME within #ifdef blocks depending on
CONFIG_PM may be dropped now.

Do that in the e1000e and igb network drivers.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e100e: use netdev_rss_key_fill() helper

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Fix TSO with non-accelerated vlans

This device claims TSO support for vlans. It also allows a
user to control vlan acceleration offloading. As such, it is
possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.

In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information. This results
in corrupted frames sent on the wire. Corruptions include
incorrect IP total length and invalid IP checksum.

This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.

CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Fix Runtime PM blocks EEE link negotiation in S5

Adding a function, and associated calls, to flush writes to (read) the LPIC
MAC register before entering the shutdown flow. This fixes the problem
of the PHY never negotiating a 100M link (if both sides of the link support
EEE and 100M link) when Runtime PM is enabled.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix EEE in S5 w/ Runtime PM enabled

The process of shutting down the system causes a call to the close PM
callback. The reset in close causes a loss of link, and the resultant
LSC interrupt causes the Runtime PM idle callback to be called. The
check for link (while link is down) in the idle callback is wiping the
information about the EEE ability of the link partner. The information is
still gone when the PHY is powered back up in the shutdown flow. This
causes EEE in S5 to fail when Runtime PM is active.

Save the link partner's EEE ability in the idle callback so that a Runtime
PM event will not cause a loss of this information.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Add code to check return values on NVM accesses

Adding code to check and respond to previously ignored return values
from NVM access functions.

Issue discovered through static analysis.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Out of line __ew32_prepare/__ew32

Out of lining these two common inlines saves about 30k text size,
due to their errata workarounds.

14131431 2008136 1507328 17646895 10d452f vmlinux-before-e1000e
14101415 2004040 1507328 17612783 10cbfef vmlinux-e1000e

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix expand setting EEE link info to all affected parts

Previously, the update_phy_task was only calling e1000_set_eee_pchlan()
for phy.type 82579. This patch is to cause this function to be called
for 82579 and newer phy.types. This causes the dev_spec->eee_lp_ability
to have the correct value when going into SX states.

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: 82574/82583 TimeSync errata for SYSTIM read

Due to a synchronization error, the value read from SYSTIML/SYSTIMH
might be incorrect.

Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Failure to write SHRA turns on PROMISC mode

Previously, the check to turn on promiscuous mode only took into account
the total number of SHared Receive Address (SHRA) registers and if the
request was for a register within that range. It is possible that the
Management Engine might have locked a number of SHRA and not allowed a
new address to be written to the requested register.

Add a function to determine the number of unlocked SHRA registers. Then
determine if the number of registers available is sufficient for our needs,
if not then return -ENOMEM so that UNICAST PROMISC mode is activated.

Since the method by which ME claims SHRA registers is non-deterministic,
also add a return value to the function attempting to write an address
to a SHRA, and return a -E1000_ERR_CONFIG if the write fails. The error
will be passed up the function chain and allow the driver to also set
UNICAST PROMISC when this happens.

Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Cleanup use of deprecated DEFINE_PCI_DEVICE_TABLE

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Cleanup to fix checkpatch missing blank lines

Fixing "WARNING:SPACING: networking uses a blank line after declarations"

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Cleanup return values in ethtool

Changing occurrences of returning 0 and 1 from bool functions to false and
true, respectively

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e/igb/ixgbe/i40e: fix message terminations

Add \n at the end of messages where missing, remove all \r.

Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Enclose e1000e_pm_thaw() with CONFIG_PM_SLEEP

Fix following compilation warning:
drivers/net/ethernet/intel/e1000e/netdev.c:6238:12: warning
‘e1000e_pm_thaw’ defined but not used [-Wunused-function]
static int e1000e_pm_thaw(struct device *dev)
^
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Correctly include VLAN_HLEN when changing interface MTU

When changing the interface mtu, the driver starts with a value
that doesn't include VLAN_HLEN. Later tests in the driver
set the rx_buffer_len based on the mtu. As a result, when
the user increases the mtu to 1504 (to support 802.1AD for example),
the driver rx_buffer_len does not change and frames longer
the 1522 bytes are rejected as too long.

Include VLAN_HLEN from the start so that an user mtu greater then
1500 bytes is correctly reflected in the driver rx_buffer_len.

CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: remove open-coded skb_cow_head

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix no connectivity when driver loaded with cable out

In commit da1e2046e5, the flow for enabling/disabling an Si errata
workaround (e1000_lv_jumbo_workaround_ich8lan) was changed to fix a problem
with iAMT connections dropping on interface down with jumbo frames set.
Part of this change was to move the function call disabling the workaround
to e1000e_down() from the e1000_setup_rctl() function. The mechanic for
disabling of this workaround involves writing several MAC and PHY registers
back to hardware defaults.

After this commit, when the driver is loaded with the cable out, the PHY
registers are not programmed with the correct default values. This causes
the device to be capable of transmitting packets, but is unable to recieve
them until this workaround is called.

The flow of e1000e's open code relies upon calling the above workaround to
expicitly program these registers either with jumbo frame appropriate settings
or h/w defaults on 82579 and newer hardware.

Fix this issue by adding logic to e1000_setup_rctl() that not only calls
e1000_lv_jumbo_workaround_ich8lan() when jumbo frames are set, to enable the
workaround, but also calls this function to explicitly disable the workaround
in the case that jumbo frames are not set.

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: remove redundant if clause from PTP work

tx_hwtstamp_skb is always set before work is scheduled,
work is cancelled before tx_hwtstamp_skb is set to NULL.
PTP work cannot ever see tx_hwtstamp_skb set to NULL.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: add timeout for TX HW time stamping work

Hardware may fail to report time stamp e.g.:
- when hardware time stamping is not enabled
- when time stamp is requested shortly after ifup

Timeout time stamp reading work to prevent it from
scheduling itself indefinitely. Report timeout events
via system log and device stats.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix Explicitly set Transmit Control Register

This patch causes the TCTL to be explicitly set to fix a problem with
poor network performance (throughput) on certain silicon when configured
for 100M HDX performance.

Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix Hardware Unit Hang

The check for pending Tx work when link is lost was mistakenly moved to be
done only when link is first detected to be lost. It turns out there is a
small window of opportunity for additional Tx work to get queued up shortly
after link is dropped.

Move the check back to the place it was before in the watchdog task. Put in
additional debug information for other reset paths and a final catch-all for
false hangs in the scheduled function that prints out the hardware hang
message.

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: fix the build error when PM is disabled

The commit 2800209994f8 (e1000e: Refactor PM flows) changed the
SET_SYSTEM_SLEEP_PM_OPS to open-coded assignment, but forgot to
protect them with CONFIG_PM_SLEEP. Then cause the following build
error when PM is disabled:
drivers/net/ethernet/intel/e1000e/netdev.c:7079:13:
error: 'e1000e_pm_suspend' undeclared here (not in a function)
.suspend = e1000e_pm_suspend,
^
drivers/net/ethernet/intel/e1000e/netdev.c:7080:13:
error: 'e1000e_pm_resume' undeclared here (not in a function)
.resume = e1000e_pm_resume,
^
drivers/net/ethernet/intel/e1000e/netdev.c:7082:11:
error: 'e1000e_pm_thaw' undeclared here (not in a function)
.thaw = e1000e_pm_thaw,
^
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: e1000e calls skb_set_hash

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.

Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Feature Enable PHY Ultra Low Power Mode (ULP)

ULP is a power saving feature that reduces the power consumption of the
PHY when a cable is not connected.

ULP is gated on the following conditions:
1) The hardware must support ULP. Currently this is only I218
devices from Intel
2) ULP is initiated by the driver, so, no driver results in no ULP.
3) ULP's implementation utilizes Runtime Power Management to toggle its
execution. ULP is enabled/disabled based on the state of Runtime PM.
4) ULP is not active when wake-on-unicast, multicast or broadcast is active
as these features are mutually-exclusive.

Since the PHY is in an unavailable state while ULP is active, any access
of the PHY registers will fail. This is resolved by utilizing kernel
calls that cause the device to exit Runtime PM (e.g. pm_runtime_get_sync)
and then, after PHY access is complete, allow the device to resume
Runtime PM (e.g. pm_runtime_put_sync).

Under certain conditions, toggling the LANPHYPC is necessary to disable
ULP mode. Break out existing code to toggle LANPHYPC to a new function
to avoid code duplication.

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e Refactor of Runtime Power Management

Fix issues with:
RuntimePM causing the device to repeatedly flip between suspend and resume
with the interface administratively downed.
Having RuntimePM enabled interfering with the functionality of Energy
Efficient Ethernet.

Added checks to disallow functions that should not be executed if the
device is currently runtime suspended

Make runtime_idle callback to use same deterministic behavior as the igb
driver.

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Refactor PM flows

Refactor the system power management flows to prevent the suspend path from
being executed twice when hibernating since both the freeze and
poweroff callbacks were set to e1000_suspend() via SET_SYSTEM_SLEEP_PM_OPS.
There are HW workarounds that are performed during this flow and calling
them twice was causing erroneous behavior.

Re-arrange the code to take advantage of common code paths and explicitly
set the individual dev_pm_ops callbacks for suspend, resume, freeze,
thaw, poweroff and restore.

Add a boolean parameter (reset) to the e1000e_down function to allow
for cases when the HW should not be reset when downed during a PM event.

Now that all suspend/shutdown paths result in a call to __e1000_shutdown()
that checks Wake on Lan status, removing redundant check for WoL in
e1000_power_down_phy().

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Cleanup - Update GPL header and Copyright

This patch is to update the GPL header by removing the portion that
refers to the Free Software Foundation address.

Change the copyright date for 2014.

Reformat the header comments to conform to kernel networking coding norms

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Fix 82579 sets LPI too early.

Enabling EEE LPI sooner than one second after link up on 82579 causes link
issues with some switches.

Remove EEE enablement for 82579 parts from the link initialization flow to
avoid initializing too early. EEE initialization for 82579 will be done
in e1000e_update_phy_task.

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Cleanup unecessary references

Cleaning up some pointer references that are no longer necessary

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Use pci_enable_msix_range() instead of pci_enable_msix()

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.

Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Fix compilation warning when !CONFIG_PM_SLEEP

Commit 7509963c703b (e1000e: Fix a compile flag mis-match for
suspend/resume) moved suspend and resume hooks to be available when
CONFIG_PM is set. However, it can be set even if CONFIG_PM_SLEEP is not set
causing following warnings to be emitted:

drivers/net/ethernet/intel/e1000e/netdev.c:6178:12: warning:
‘e1000_suspend’ defined but not used [-Wunused-function]

drivers/net/ethernet/intel/e1000e/netdev.c:6185:12: warning:
‘e1000_resume’ defined but not used [-Wunused-function]

To fix this make the hooks to be available only when CONFIG_PM_SLEEP is set
and remove CONFIG_PM wrapping from driver ops because this is already
handled by SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS().

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Aaron Brown <aaron.f.brown@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Fix a compile flag mis-match for suspend/resume

This patch addresses a mis-match between the declaration and usage of
the e1000_suspend and e1000_resume functions. Previously, these
functions were declared in a CONFIG_PM_SLEEP wrapper, and then utilized
within a CONFIG_PM wrapper. Both the declaration and usage will now be
contained within CONFIG_PM wrappers.

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Implement the SIOCGHWTSTAMP ioctl

Compile-tested only.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

e1000e: Validate hwtstamp_config completely before applying it

e1000e_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes. Currently it copies the configuration to
the e1000_adapter structure before validating it at all.

Change e1000e_config_hwtstamp() to take a pointer to the
hwstamp_config and to copy the config after validating it.

Compile-tested only.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DMA-API: net: intel/e1000e: fix 32-bit DMA mask handling

The fallback to 32-bit DMA mask is rather odd:
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err) {
err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err)
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev,
"No usable DMA configuration, aborting\n");
goto err_dma;
}
}
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.

Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

e1000e: cleanup boolean comparison to true

Removing a comparison to the boolean value true where simply interrogating
the lvalue will produce the same result.

Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Avoid kernel crash during shutdown

While doing shutdown on the PCI device, the corresponding callback
function e1000e_shutdown() is trying to clear those correctable
errors on the upstream P2P bridge. Unfortunately, we don't have
the upstream P2P bridge under some cases (e.g. PCI-passthrou for
KVM on Power). That leads to kernel crash eventually.

The patch adds one more check on that to avoid kernel crash.

Signed-off-by: Li Zhang <zhlcindy@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Add code to check for failure of pci_disable_link_state call

This patch attempts to work around a problem found with some systems where
the call to pci_diable_link_state_locked() fails. As a result, ASPM is not,
in fact, disabled. Changing disable ASPM code to check if state actually
is disabled after the call and, if not, try another way to disable it.

Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: do not resume device from RPM suspend to read PHY status registers

When the device is runtime suspended (e.g. when there is no link), do not
wake it from D3 to read the PHY status; just set the values to typical
power-on defaults as is done when runtime PM is not enabled and there is no
link.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: enable support for new device IDs

The device IDs 0x15a0 and 0x15a1 are new SKUs that contain the same MAC as
I217 and same PHY as I218.

The device IDs 0x15a2 and 0x15a3 are the same as existing I218 SKUs.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: low throughput using 4K jumbos on I218

Alter the packet buffer allocation accordingly.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: iAMT connections drop on driver unload when jumbo frames enabled

The jumbo frame configuration in the MAC/PHY should be reverted on 82579
and newer parts when the interface is brought down (not just when the MTU
is changed back to standard frame size) otherwise iAMT connections (e.g.
SoL, IDE-R) will be dropped and cannot be re-acquired until the MTU is
changed again.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Remove duplicate assignment of default rx/tx ring size

tx_ring/rx_ring size is assigned in function e1000_alloc_queues(), which is
called by e1000_sw_init() in the early stage of e1000_probe().

This patch just remove the duplicate assignment of this default ring size
value.

Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Da Yu Qiu <qiudayu@cn.ibm.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: restore call to pci_clear_master()

In attempting to resolve a minor merge conflict, commit e5f2ef7ab4690d2e8faa
(Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net) accidentally
dropped a call to pci_clear_master() that was intended to remain in place.

Commit 4e0855dff094b0d56d6b (e1000e: fix pci-device enable-counter balance)
replaced a call to pci_disable_device() by one to pci_clear_master(). And then
commit 66148babe728f3e00e13 (e1000e: fix runtime power management transitions)
deleted a number of lines starting two lines following that call.

This patch restores the call to pci_clear_master() in __e1000_shutdown().

v2: added summary lines (enclosed in parens) following commit IDs

Signed-off-by: Dean Nelson <dnelson@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: prevent warning from -Wunused-parameter

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup whitespace

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: panic caused by Rx traffic arriving while interface going down

An "unable to handle kernel paging request" panic can occur when receiving
traffic while the interface is going down. Wait for NAPI to be done with
current context after disabling interrupts and then disable NAPI.

See https://bugzilla.vyatta.com/show_bug.cgi?id=8837.

Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net: vlan: add protocol argument to packet tagging functions

Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: vlan: prepare for 802.1ad VLAN filtering offload

Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: vlan: rename NETIF_F_HW_VLAN_* feature flags to NETIF_F_HW_VLAN_CTAG_*

Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: increase driver version number

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: EEE capability advertisement not set/disabled as required

Devices supported by the driver which support EEE (currently 82579, I217
and I218) are advertising EEE capabilities during auto-negotiation even
when EEE has been disabled. In addition to not acting as expected, this
also caused the EEE status reported by 'ethtool --show-eee' to be wrong
when two of these devices are connected back-to-back and EEE is disabled
on one. In addition to fixing this issue, the ability for the user to
specify which speeds (100 or 1000 full-duplex) to advertise EEE support
has been added.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Add missing dma_mapping_error-call in e1000_alloc_jumbo_rx_buffers

After dma_map_page, dma_mapping_error must be called. It seems safe to
not free the skb/page allocated in this function, as the skb/page can be
reused later.

Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup - move defines to appropriate header file

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup unnecessary line breaks

Cuddle broken lines where appropriate.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup unusually placed comments

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup (add/remove) blank lines where appropriate

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup SPACING checkpatch checks

CHECK:SPACING: No space is necessary after a cast
CHECK:SPACING: space prohibited before semicolon

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup PARENTHESIS_ALIGNMENT checkpatch checks

CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup LEADING_SPACE checkpatch warnings

WARNING:LEADING_SPACE: please, no spaces at the start of a line

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup LONG_LINE checkpatch warnings

WARNING:LONG_LINE: line over 80 characters

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: cleanup SPACING checkpatch errors and warnings

ERROR:SPACING: spaces prohibited around that ':' (ctx:WxV)
ERROR:SPACING: need consistent spacing around '-' (ctx:WxV)
ERROR:SPACING: space required after that ',' (ctx:VxV)
ERROR:SPACING: spaces required around that '=' (ctx:VxV)
WARNING:SPACING: missing space after enum definition

and some similar spacing issues not reported by checkpatch.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>