net: hns3: Disable SerDes serial loopback for HiLink H60

When the hilink version is H60, the serdes serial loopback test is not
supported. This patch add hilink version detection. When the version
is H60, the serdes serial loopback test will be disable.

Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add new 200G link modes for hisilicon device

The hisilicon device now supports a new 200G link interface,
which query from firmware in a new bit. Therefore,
the HCLGE_SUPPORT_200G_R4_BIT capability bit has been added.
The HCLGE_SUPPORT_200G_BIT has been renamed as
HCLGE_SUPPORT_200G_R4_EXT_BIT, and the firmware has
extended support for this mode.

Fixes: ae6f010cb1a7 ("net: hns3: add support for 200G device")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add some link modes for hisilicon device

Add HCLGE_SUPPORT_50G_R1_BIT and HCLGE_SUPPORT_100G_R2_BIT two
capability bits and Corresponding link modes.

Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add vf fault detect support

Currently hns3 driver supports vf fault detect feature. Several ras caused
by VF resources don't need to do PF function reset for recovery. The driver
only needs to reset the specified VF.

So this patch adds process in ras module. New process will get detailed
information about ras and do the most correct measures based on these
accurate information.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20231007031215.1067758-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: fix invalid mutex between tc qdisc and dcb ets command issue

We hope that tc qdisc and dcb ets commands can not be used crosswise.
If we want to use any of the commands to configure tc,
We must use the other command to clear the existing configuration.

However, when we configure a single tc with tc qdisc,
we can still configure it with dcb ets.
Because we use mqprio_active as the tag of tc qdisc configuration,
but with dcb ets, we do not check mqprio_active.

This patch fix this issue by check mqprio_active before
executing the dcb ets command. and add dcb_ets_active to
replace HCLGE_FLAG_DCB_ENABLE and HCLGE_FLAG_MQPRIO_ENABLE
at the hclge layer,

Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: hns3: move dump regs function to a separate file

The dump register function is being refactored.
The first step in refactoring is put the dump regs function
into a separate file.

Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Remove unused function declarations

Commit 1e6e76101fd9 ("net: hns3: configure promisc mode for VF asynchronously")
left behind hclge_inform_vf_promisc_info() declaration.
And commit 68c0a5c70614 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd Interface Support")
declared but never implemented hclge_cmd_mdio_write() and hclge_cmd_mdio_read().

Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230803135138.37456-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: refine the tcam key convert handle

The result of expression '(k ^ ~v) & k' is exactly
the same with 'k & v', so simplify it.
(k ^ ~v) & k == k & v
The truth table (in non table form):
k == 0, v == 0:
(k ^ ~v) & k == (0 ^ ~0) & 0 == (0 ^ 1) & 0 == 1 & 0 == 0
k & v == 0 & 0 == 0

k == 0, v == 1:
(k ^ ~v) & k == (0 ^ ~1) & 0 == (0 ^ 0) & 0 == 1 & 0 == 0
k & v == 0 & 1 == 0

k == 1, v == 0:
(k ^ ~v) & k == (1 ^ ~0) & 1 == (1 ^ 1) & 1 == 0 & 1 == 0
k & v == 1 & 0 == 0

k == 1, v == 1:
(k ^ ~v) & k == (1 ^ ~1) & 1 == (1 ^ 0) & 1 == 1 & 1 == 1
k & v == 1 & 1 == 1
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: hns3: support wake on lan configuration and query

The HNS3 driver supports Wake-on-LAN, which can wake up
the server from power off state to power on state by magic
packet or magic security packet.

ChangeLog:
v1->v2:
Deleted the debugfs function that overlaps with the ethtool function
from suggestion of Andrew Lunn.

v2->v3:
Return the wol configuration stored in driver,
suggested by Alexander H Duyck.

v3->v4:
Add a helper to go from netdev to the local struct,
suggested by Simon Horman and Jakub Kicinski.

Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refine the handling for VF heartbeat

Currently, the PF check the VF alive by the KEEP_ALVE
mailbox from VF. VF keep sending the mailbox per 2
seconds. Once PF lost the mailbox for more than 8
seconds, it will regards the VF is abnormal, and stop
notifying the state change to VF, include link state,
vf mac, reset, even though it receives the KEEP_ALIVE
mailbox again. It's inreasonable.

This patch fixes it. PF will record the state change which
need to notify VF when lost the VF's KEEP_ALIVE mailbox.
And notify VF when receive the mailbox again. Introduce a
new flag HCLGE_VPORT_STATE_INITED, used to distinguish the
case whether VF driver loaded or not. For VF will query
these states when initializing, so it's unnecessary to
notify it in this case.

Fixes: aa5c4f175be6 ("net: hns3: add reset handling for VF when doing PF reset")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: optimize converting dscp to priority process of hns3_nic_select_queue()

Currently, when function hns3_nic_select_queue() converts dscp to priority,
it calls an indirect callback ae_algo->ops->get_dscp_prio to get priority.

However as function hns3_nic_select_queue() is in fast path, the indirect
call may cause degradation of performance. For optimization, this patch
moves dscp_app_cnt and dscp_prio from struct hclge_tm_info to struct
hnae3_knic_private_info, so they can be used in both hclge and hns3 layers.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: add support to query and set lane number by ethtool

When serdes lane support setting 25Gb/s or 50Gb/s speed and user wants to
set port speed as 50Gb/s, it can be setted as one 50Gb/s serdes lane or
two 25Gb/s serdes lanes.

So, this patch adds support to query and set lane number by ethtool
to satisfy this scenario.

Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add querying fec statistics

FEC statistics can be used to check the transmission quality of links.
This patch implements the get_fec_stats callback of ethtool_ops to support
querying FEC statistics by command "ethtool -I --show-fec eth0".

Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support config dscp map to tc

This patch add support config dscp map to tc by implementing ieee_setapp
and ieee_delapp of struct dcbnl_rtnl_ops. Driver will convert mapping
relationship from dscp-prio to dscp-tc.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add byte order conversion for VF to PF mailbox message

This patch uses __le16/__32 to define mailbox data structures. Then byte
order conversion are added for mailbox messages from VF to PF.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove the affinity settings of vector0

Vector0 is used for common interrupt control events and is
irrelevant to performance. Currently, the driver sets the
default affinity of vector0 to NUMA nodes, which is unnecessary.
Therefore, the default setting is removed, and the driver does
not set the affinity for vector0.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add vlan list lock to protect vlan list

When adding port base VLAN, vf VLAN need to remove from HW and modify
the vlan state in vf VLAN list as false. If the periodicity task is
freeing the same node, it may cause "use after free" error.
This patch adds a vlan list lock to protect the vlan list.

Fixes: c6075b193462 ("net: hns3: Record VF vlan tables")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: fix port base vlan add fail when concurrent with reset

Currently, Port base vlan is initiated by PF and configured to its VFs,
by using command "ip link set <pf name> vf <vf id> vlan <vlan id>".
When a global reset was triggered, the hardware vlan table and the soft
recorded vlan information will be cleared by PF, and restored them until
VFs were ready. There is a short time window between the table had been
cleared and before table restored. If configured a new port base vlan tag
at this moment, driver will check the soft recorded vlan information,
and find there hasn't the old tag in it, which causing a warning print.

Due to the port base vlan is managed by PF, so the VFs's port base vlan
restoring should be handled by PF when PF was ready.

This patch fixes it.

Fixes: 039ba863e8d7 ("net: hns3: optimize the filter table entries handling when resetting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: Remove unused inline function hclge_is_reset_pending()

This is unused since commit 8e2288cad6cb ("net: hns3: refactor PF
cmdq init and uninit APIs with new common APIs").

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Jie Wang <wangjie125@huawei.com>
Link: https://lore.kernel.org/r/20220216113507.22368-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: add support for TX push mode

For the device that supports the TX push capability, the BD can
be directly copied to the device memory. However, due to hardware
restrictions, the push mode can be used only when there are no
more than two BDs, otherwise, the doorbell mode based on device
memory is used.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor PF tqp stats APIs with new common tqp stats APIs

This patch firstly uses new tqp struct(hclge_comm_tqp) and deletes the
old PF tqp struct(hclge_tqp). All the tqp stats members used in PF module
are modified according to the new hclge_comm_tqp.

Secondly PF tqp stats APIs are refactored to use new common tqp stats APIs.
The old tqp stats APIs in PF are deleted.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor PF rss set APIs with new common rss set APIs

This patch uses new common rss set APIs to replace the old APIs in PF rss
module and deletes the old rss set APIs. The related macros are also
modified.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor PF rss get APIs with new common rss get APIs

This patch firstly uses new rss parameter struct(hclge_comm_rss_cfg) as
child member of hclge_dev and deletes the original child rss parameter
members in vport. All the vport child rss parameter members used in PF rss
module is modified according to the new hclge_comm_rss_cfg.

Secondly PF rss get APIs are refactored to use new common rss get APIs. The
old rss get APIs in PF are deleted.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor PF cmdq init and uninit APIs with new common APIs

This patch uses common cmdq init and uninit APIs to replace the old APIs in
PF cmdq module init and uninit modules. Then the old PF init and uninit
APIs is deleted.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor hclge_cmd_send with new hclge_comm_cmd_send API

This patch firstly uses new hardware description struct hclge_comm_hw as
child member of hclge_hw and deletes the original child memebers of
hclge_hw. All the hclge_hw variables used in PF module is modified
according to the new hclge_hw.

Secondly hclge_cmd_send is refactored to use hclge_comm_cmd_send APIs. The
old functions called by hclge_cmd_send are deleted and hclge_cmd_send is
kept to avoid too many meaningless modifications.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refine function hclge_cfg_mac_speed_dup_hw()

To reuse the code of converting speed of driver to speed of firmware in
function hclge_cfg_mac_speed_dup_hw(), encapsulate them into a new
function hclge_convert_to_fw_speed().

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add log for workqueue scheduled late

When the mbx or reset message arrives, the driver is informed
through an interrupt. This task can be processed only after
the workqueue is scheduled. In some cases, this workqueue
scheduling takes a long time. As a result, the mbx or reset
service task cannot be processed in time. So add some warning
message to improve debugging efficiency for this case.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix some mac statistics is always 0 in device version V2

When driver queries the register number of mac statistics from firmware,
the old firmware runs in device version V2 only returns number of valid
registers, not include number of three reserved registers among of them.
It cause driver doesn't record the last three data when query mac
statistics.

To fix this problem, driver never query register number in device version
V2 and set it to a fixed value which include three reserved registers.

Fixes: c8af2887c941 ("net: hns3: add support pause/pfc durations for mac statistics")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix pfc packet number incorrect after querying pfc parameters

Currently, driver will send command to firmware to query pfc packet number
when user uses dcb tool to get pfc parameters. However, the periodic
service task will also periodically query and record MAC statistics,
including pfc packet number.

As the hardware registers of statistics is cleared after reading, it will
cause pfc packet number of MAC statistics are not correct after using dcb
tool to get pfc parameters.

To fix this problem, when user uses dcb tool to get pfc parameters, driver
updates MAC statistics firstly and then get pfc packet number from MAC
statistics.

Fixes: 64fd2300fcc1 ("net: hns3: add support for querying pfc puase packets statistic")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix ROCE base interrupt vector initialization bug

Currently, NIC init ROCE interrupt vector with MSIX interrupt. But ROCE use
pci_irq_vector() to get interrupt vector, which adds the relative interrupt
vector again and gets wrong interrupt vector.

So fixes it by assign relative interrupt vector to ROCE instead of MSIX
interrupt vector and delete the unused struct member base_msi_vector
declaration of hclgevf_dev.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support pause/pfc durations for mac statistics

The mac statistics add pause/pfc durations in device version V3, we can
get total active cycle of pause/pfc from these durations.

As driver gets register number from firmware to calculate desc number to
query mac statistics, it needs to set mac statistics extended enable bit
in firmware command 0x701A to tell firmware that driver supports extended
mac statistics, otherwise firmware only returns register number of
version V1.

As pause/pfc durations are not supported by hardware of old version, they
should not been shown in command "ethtool -S ethX" in this case, so add
checking max register number of each mac statistic in their version.
If the max register number of one mac statistic is greater than register
number got from firmware, it means hardware does not support this mac
statistic, so ignore this statistic when get string and data of mac
statistic.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: modify mac statistics update process for compatibility

After querying mac statistics from firmware, driver copies data from
descriptors to struct mac_stats of hdev, and the number of copied data
is just according to the register number queried from firmware. There is
a problem that if the register number queried from firmware is larger
than data number of struct mac_stats, it will cause a copy overflow.

So if the firmware adds more mac statistics in later version, it is not
compatible with driver of old version.

To fix this problem, the number of copied data needs to be used the
minimum value between the register number queried from firmware and
data number of struct mac_stats.

The first descriptor has three data and there is one reserved, to
optimize the copy process, add this reserverd data to struct mac_stats.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: PF support get multicast MAC address space assigned by firmware

The new firmware supports to divides the whole multicast MAC address space
equally to functions of all PFs, and calculates the space size of each PF
according to its function number.

To support this feature, PF driver adds querying multicast MAC address
space size from firmware and limits used number according to space size.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: change hclge/hclgevf workqueue to WQ_UNBOUND mode

Currently, the workqueue of hclge/hclgevf is executed on
the CPU that initiates scheduling requests by default. In
stress scenarios, the CPU may be busy and workqueue scheduling
is completed after a long period of time. To avoid this
situation and implement proper scheduling, use the WQ_UNBOUND
mode instead. In this way, the workqueue can be performed on
a relatively idle CPU.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add new function hclge_get_speed_bit()

Currently, function hclge_check_port_speed() uses switch/case statement
to get speed bit according to speed. To reuse this part of code and
improve code readability and maintainability, add a new function
hclge_get_speed_bit() to get speed bit according to map relationship
of speed and speed bit defined in array speed_bit_map.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: merge some repetitive macros

There are some repetitive macros have same meaning and value, this patch
merges them to make code clean.

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for triggering reset by ethtool

Currently, four reset types are supported for the HNS3 ethernet
driver: IMP reset, global reset, function reset, and FLR. Only
FLR can now be triggered by the user. To restore the device when
an exception occurs, add support for triggering reset by ethtool.

Run the "ethtool --reset DEVNAME mgmt | all | dedicated" to
trigger the IMP | global | function reset manually.

In addition, VF can only trigger function reset.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Link: https://lore.kernel.org/r/1628602128-15640-1-git-send-email-huangguangbin2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: add support for registering devlink for PF

Add devlink register support for HNS3 ethernet PF driver.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix GRO configuration error after reset

The GRO configuration is enabled by default after reset. This
is incorrect and should be restored to the user-configured value.
So this restoration is added during reset initialization.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: add support to query tx spare buffer size for pf

Add support to query tx spare buffer size from configuration
file, and use this info to do spare buffer initialization when
the module parameter 'tx_spare_buf_size' is not specified.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for PTP

Adds PTP support for HNS3 ethernet driver.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for handling all errors through MSI-X

Currently, hardware errors can be reported through AER or MSI-X mode.
However, the AER mode is intended to handle only bus errors, but not
hardware errors. On the other hand, virtual machines cannot handle
AER errors. When an AER error is reported, virtual machines will be
suspended. So add support for handling all these hardware errors
through MSI-X mode which depends on a newer version of firmware,
and reserve the handler of the AER mode for compatibility.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add a separate error handling task

Error handling and recovery logic are intertwined. Error handling (i.e.
error identification, clearing error sources and initiation of recovery)
is done in context of reset task. If certain hardware errors get
delivered during driver init time, which can cause driver init/loading
to fail.

Introduce a separate error handling task to ensure below:

1. Reset logic remains independent of the error handling logic.
2. Add the hclge_errhand_task_schedule to schedule error recovery
tasks, This will ensure that common misellaneous MSI-X interrupt are
re-enabled quickly.

Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add debugfs support for vlan configuration

Add debugfs support for vlan configuraion. create a single file
"vlan_config" for it, and query it by command "cat vlan_config",
return the result to userspace.

The new display style is below:
$ cat vlan_config
I_PORT_VLAN_FILTER: on
E_PORT_VLAN_FILTER: off
FUNC_ID I_VF_VLAN_FILTER E_VF_VLAN_FILTER PORT_VLAN_FILTER_BYPASS
pf off on off
vf0 off on off
FUNC_ID PVID ACCEPT_TAG1 ACCEPT_TAG2 ACCEPT_UNTAG1 ACCEPT_UNTAG2
pf 0 on on on on
vf0 0 on on on on

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: add support for VF modify VLAN filter state

Previously, there is hardware limitation for VF to modify
the VLAN filter state, and the VLAN filter state is default
enabled. Now the limitation has been removed in some device,
so add capability flag to check whether the device supports
modify VLAN filter state. If flag on, user will be able to
modify the VLAN filter state by ethtool -K.
VF needs to send mailbox to request the PF to modify the VLAN
filter state for it.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: add support for modify VLAN filter state

Previously, with hardware limitation, the port VLAN filter are
effective for both PF and its VFs simultaneously, so a single
function is not able to enable/disable separately, and the VLAN
filter state is default enabled. Now some device supports each
function to bypass port VLAN filter, then each function can
switch VLAN filter separately. Add capability flag to check
whether the device supports modify VLAN filter state. If flag
on, user will be able to modify the VLAN filter state by ethtool
-K.

Furtherly, the default VLAN filter state is also changed
according to whether non-zero VLAN used. Then the device can
receive packet with any VLAN tag if only VLAN 0 used.

The function hclge_need_enable_vport_vlan_filter() is used to
help implement above changes. And the VLAN filter handle for
promisc mode can also be simplified by this function.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: refine function hclge_set_vf_vlan_cfg()

The struct hclge_vf_vlan_cfg is firstly designed for setting
VLAN filter tag. And it's reused for enable RX VLAN offload
later. It's strange to use member "is_kill" to indicate "enable".
So redefine the struct hclge_vf_vlan_cfg to adapt it.

For there are already 3 subcodes being used in function
hclge_set_vf_vlan_cfg(), use "switch-case" style for each
branch, rather than "if-else". Also simplify the assignment for
each branch to make it more clearly.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: refine for hclge_push_vf_port_base_vlan_info()

Use struct "hclge_vlan_info" instead of separately parameters
for function hclge_push_vf_port_base_vlan_info(), to make it
more concise.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: use HCLGE_VPORT_STATE_PROMISC_CHANGE to replace HCLGE_STATE_PROMISC_CHANGED

Currently, PF is using HCLGE_STATE_PROMISC_CHANGED to indicate
need synchronize the promisc mode for itself, and using flag
HCLGE_VPORT_STATE_PROMISC_CHANGE for its VF. To keep consistent,
remove flag HCLGE_STATE_PROMISC_CHANGED, and use flag
HCLGE_VPORT_STATE_PROMISC_CHANGE instead.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: configure promisc mode for VF asynchronously

Currently, when host set VF untrusted, the driver will disable
the promisc mode of VF. It may be conflicted when the VF requests
the host to set promisc mode. So refactor it by changing promisc
mode for VF asynchronously. With this change, the promisc mode of
VF can be restored when the VF being trusted again.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove the useless debugfs file node cmd

Currently, all debugfs commands have been reconstructed, and the
debugfs file node cmd is useless. So remove this debugfs file node.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor dump reset info of debugfs

Currently, the debugfs command for reset info is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"reset_info" for it, and query it by command "cat reset_info",
return the result to userspace, rather than record in dmesg.

The display style is below:
$cat reset_info
PF reset count: 0
FLR reset count: 0
GLOBAL reset count: 0
IMP reset count: 0
reset done count: 0
HW reset done count: 0
reset count: 0
reset fail count: 0
vector0 interrupt enable status: 0x1
reset interrupt source: 0x0
reset interrupt status: 0x0
RAS interrupt status:0x0
hardware reset status: 0x0
handshake status: 0x80
function reset status: 0x0

Change to the "hclge_show_rst_info" in the "hclge_reset_err_handle",
when the reset fails, display reset info immediately.

Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor the debugfs process

Currently, each debugfs command needs to create a file to get
the information. To better support more debugfs commands, the
debugfs process is reconstructed, including the process of
creating dentries and files, and obtaining information.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: support RXD advanced layout

Currently, the driver gets packet type by parsing the
L3_ID/L4_ID/OL3_ID/OL4_ID from RX descriptor, it's
time-consuming.

Now some new devices support RXD advanced layout, which combines
previous OL3_ID/OL4_ID to 8bit ptype field, so the driver gets
packet type by looking up only one table, and L3_ID/L4_ID become
reserved fields.

Considering compatibility, the firmware will report capability of
RXD advanced layout, the driver will identify and enable it by
default. This patch provides basic function: identify and enable
the RXD advanced layout, and refactor out hns3_rx_checksum() by
using ptype table to handle RX checksum if supported.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: PF add support for pushing link status to VFs

Previously, VF updates its link status every second by send query command
to PF in periodic service task. If link stats of PF is changed, VF may
need at most one second to update its link status.

To reduce delay of link status between PF and VFs, PF actively push its
link status to VFs when its link status is updated. And to let VF know
PF supports this new feature, the link status changed mailbox command
adds one bit to indicate it.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: optimize the process of queue reset

Currently, the queue reset process needs to be performed one by
one, which is inefficient. However, the queue reset of the same
function is always performed at the same time. Therefore, according
to the UM, command HCLGE_OPC_CFG_RST_TRIGGER can be used to reset
all queues of the same function at a time, in order to optimize
the queue reset process.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove unused code of vmdq

Vmdq is not supported yet, the num_vmdq_vport is always 0,
it's a bit confusing when using the num_vport, so remove
these unused codes of vmdq.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for user-def data of flow director

For DEVICE_VERSION_V3, the hardware supports to match specified
data in the specified offset of packet payload. Each layer can
have one offset, and can't be masked when configure flow director
rule by ethtool command. The layer is selected based on the
flow-type, ether for L2, ip4/ipv6 for L3, and tcp4/tcp6/udp4/udp6
for L4. For example, tcp4/tcp6/udp4/udp6 rules share the same
user-def offset, but each rule can have its own user-def value.

For the user-def field of ethtool -N/U command is 64 bits long.
The bit 0~15 is used for user-def value, and bit 32~47 for user-def
offset in HNS3 driver.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor flow director configuration

Currently, the flow director rule of aRFS is configured in
the IO path. It's time-consuming. So move out the configuration,
and configure it asynchronously. And keep ethtool and tc flower
rule using synchronous way, otherwise the application maybe
unable to know the rule is installed or pending.

Add a state member for each flow director rule to indicate the
rule state. There are 4 states:
TO_ADD: the rule is waiting to add to hardware
TO_DEL: the rule is waiting to remove from hardware
DELETED: the rule has been removed from hardware. It's a middle
state, used to remove the rule node in the fd_rule_list.
ACTIVE: the rule is already added in hardware

For asynchronous way, when receive a new request to add or delete
flow director rule by aRFS, update the rule list, then request to
schedule the service task to finish the configuration.

For synchronous way, when receive a new request to add or delete
flow director rule by ethtool or tc flower, configure hardware
directly, then update the rule list if success.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor for function hclge_fd_convert_tuple

Currently, there are too many branches for hclge_fd_convert_tuple().
And it may be more when add new tuples. Refactor it by sorting the
tuples according to their length. So it only needs several KEY_OPT
now, and being flexible to add new tuples.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove unused macro definition

Some macros are defined but unused, so remove them.

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: clean up unnecessary parentheses in macro definitions

In macro definitions, parentheses are unnecessary in some cases,
such as the calling parameter of a function, the left variable
of the equal sign, and so on. So remove these unnecessary
parentheses according to these rules.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: replace macro of max qset number with specification

The max qset number is a fixed value now and it is defined by a macro.
In order to support other value in different kinds of device, it is
better to use specification queried from firmware to replace macro.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: optimize the code when update the tc info

When update the TC info for NIC, there are some differences
between PF and VF. Currently, four "vport->vport_id" are
used to distinguish PF or VF. So merge them into one to
improve readability and maintainability of code.

Signed-off-by: GuoJia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: RSS indirection table use device specification

As RSS indirection table size may be different in different
hardware. Instead of using macro, this value is better to use
device specification which querying from firmware.

BTW, RSS indirection table should be allocated by the queried
size instead the static array.

.get_rss_indir_size in struct hnae3_ae_ops is not used now,
so remove it as well.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: add debugfs support for tm nodes, priority and qset info

In order to query tm info of nodes, priority and qset
for debugging, adds three debugfs files tm_nodes,
tm_priority and tm_qset in newly created tm directory.

Unlike previous debugfs commands, these three files
just support read ops, so they only support to use cat
command to dump their info.

The new tm file style is acccording to suggestion from
Jakub Kicinski's opinion as link https://lkml.org/lkml/2020/9/29/2101.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: fix incorrect handling of sctp6 rss tuple

For DEVICE_VERSION_V2, the hardware only supports src-ip,
dst-ip and verification-tag for rss tuple set of sctp6
packet. For DEVICE_VERSION_V3, the hardware supports
src-port and dst-port as well.

Currently, when user queries the sctp6 rss tuples info,
some unsupported information will be showed on V2. So add
a check for hardware version when initializing and queries
sctp6 rss tuple to fix this issue.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for max 512 rss size

Currently, the driver gets the max rss size from configuration
file when initialization. Both the PF and VF share the same
max rss size, and no more than 128.

For DEVICE_VERSION_V3, the max rss size for PF can be up to
512, so there is a new field in configuration file to store it,
the old filed is used for VF.

To be compatible with boards using old configure file, the PF
will use the old filed if the one is zero.

For the rss size may be larger than 256, so the type of
rss_indirection_tbl of struct hclge_vport should be changed to
u16 as well.

Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for hw tc offload of tc flower

Some new device supports forwarding packet to queues of specified
TC when flow director rule hit. So add support to configure flow
director rule by tc flower. To avoid rule conflict, add a new flow
director mode HCLGE_FD_TC_FLOWER_ACTIVE, and only one mode can be
active at the same time.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for forwarding packet to queues of specified TC when flow director rule hit

For some new device, it supports forwarding packet to queues
of specified TC when flow director rule hit. So extend the
command handle to support it.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refine the VLAN tag handle for port based VLAN

For DEVICE_VERSION_V2, the hardware only supports max two layer
VLAN tags, including port based tag inserted by hardware, tag in
tx buffer descriptor(get from skb->tci) and tag in packet.

For transmit packet:
If port based VLAN disabled, and vf driver gets a VLAN tag from
skb, the VLAN tag must be filled to the Outer_VLAN_TAG field
(tag near to DMAC) of tx buffer descriptor, otherwise it may
be inserted after the tag in packet.

If port based VLAN enabled, and vf driver gets a VLAN tag from
skb, the VLAN tag must be filled to the VLAN_TAG field (tag
far to DMAC) of tx buffer descriptor, otherwise it may be
conflicted with port based VLAN, and raise a hardware error.

For receive packet:
The hardware will strip the VLAN tags and fill them in the rx
buffer descriptor, no matter port based VLAN enable or not.
Because port based VLAN tag is useless for stack, so vf driver
needs to discard the port based VLAN tag get from rx buffer
descriptor when port based VLAN enabled.

So vf must know about the port based VLAN state.

For DEVICE_VERSION_V3, the hardware provides some new
configuration to improve it.

For transmit packet:
When enable tag shift mode, hardware will handle the VLAN tag
in outer_VLAN_TAG field as VLAN_TAG, so it won't conflict with
port based VLAN. And hardware also make sure the tag before
the tag in packet. So vf driver doesn't need to specify the tag
position according to the port based VLAN state anymore.

For receive packet:
When enable discard mode, hardware will strip and discard the
port based VLAN tag, so vf driver doesn't need to identify it
from rx buffer descriptor.

So modify the port based VLAN configuration, simplify the process
for vf handling the VLAN tag.

Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: add support for pf querying new interrupt resources

For HNAE3_DEVICE_VERSION_V3, a maximum of 1281 interrupt
resources are supported. To utilize these new resources,
extend the corresponding field or variable to 16bit type,
and remove the restriction of NIC client that only use a
maximum of 65 interrupt vectors. In addition, the I/O address
of the extended interrupt resources are different, so an extra
handler is needed.

Currently, the total number of interrupts is the sum of RoCE's
number and RoCE's offset (RoCE is in front of NIC), since
the number of both NIC and RoCE are same. For readability,
rewrite the corresponding field of the command, rename the
RoCE's offset field as the number of NIC interrupts, then
the total number of interrupts is sum of the number of RoCE
and NIC, and replace vport->back with hdev in
hclge_init_roce_base_info() for simplifying the code.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: add support for mapping device memory

For device who has device memory accessed through the PCI BAR4,
IO descriptor push of NIC and direct WQE(Work Queue Element) of
RoCE will use this device memory, so add support for mapping
this device memory, and add this info to the RoCE client whose
new feature needs.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: add support for 200G device

The 200G device has a new device id 0xA228, so adds this device id to
pci table, then the driver can probe it.

As speed_ability queried from firmware has only 8 bits and already be
used up, so firmware adds extra speed_ability_ext to indicate more
speed abilities to support 200G and driver needs to parse it.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove unused field 'tc_num_last_time' in struct hclge_dev

'tc_num_last_time' is defined, but never used, so remove it.

Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix a typo in struct hclge_mac

The member link of struct hclge_mac stores the link status of
MAC and PHY if PHY exists, but its annotation uses word "exit",
so fix it.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix return value error when query MAC link status fail

Currently, PF queries the MAC link status per second by calling
function hclge_get_mac_link_status(). It return the error code
when failed to send cmdq command to firmware. It's incorrect,
because this return value is used as the MAC link status, which
0 means link down, and none-zero means link up. So fixes it.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove some unused fields in struct hclge_dev

Remove some fields in struct hclge_dev which have not been used.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: optimize the filter table entries handling when resetting

Currently, the PF driver removes all (including its VFs') MAC/VLAN
flow director table entries when resetting, and restores them after
reset completed.

In fact, the hardware will clear all table entries only in IMP
reset and global reset. So driver only needs to restore the table
entries in these cases, and needs do nothing when PF reset, FLR
or other function level reset.

This patch optimizes it by removing unnecessary table entries clear
and restoring handling in the reset flow, and doing the restoring
after reset completed.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: use mutex vport_lock instead of mutex umv_lock

Currently, the driver use mutex umv_lock to protect the variable
vport->share_umv_size. And there is already a mutex vport_lock
being defined in the driver, which is designed to protect the
resource of vport. So we can use vport_lock instead of umv_lock.

Furthermore, there is a time window for protect share_umv_size
between checking UMV space and doing MAC configuration in the
lin function hclge_add_uc_addr_common(). It should be extended.

This patch uses mutex vport_lock intead of spin lock umv_lock to
protect share_umv_size, and adjusts the mutex's range.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor the promisc mode setting

As the HNS3 driver doesn't update the MAC address directly in
function hns3_set_rx_mode() now, it can't know whether the
MAC table is full from __dev_uc_sync() and __dev_mc_sync(),
so it's senseless to handle the overflow promisc here.

This patch removes the handle of overflow promisc from function
hns3_set_rx_mode(), and updates the promisc mode in the service
task.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor the MAC address configure

Currently, the HNS3 driver sync and unsync MAC address in function
hns3_set_rx_mode(). For PF, it adds and deletes MAC address directly
in the path of dev_set_rx_mode(). If failed, it won't retry until
next calling of hns3_set_rx_mode(). On the other hand, if request
add and remove a same address many times at a short interval, each
request must be done one by one, can't be merged. For VF, it sends
mailbox messages to PF to request adding or deleting MAC address in
the path of function hns3_set_rx_mode(), no matter the address is
configured success.

This patch refines it by recording the MAC address in function
hns3_set_rx_mode(), and updating MAC address in the service task.
If failed, it will retry by the next calling of periodical service
task. It also uses some state to mark the state of each MAC address
in the MAC list, which can help merge configure request for a same
address. With these changes, when global reset or IMP reset occurs,
we can restore the MAC table with the MAC list.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove useless proto_support field in struct hclge_fd_cfg

proto_support field in struct hclge_fd_cfg shows what protocols
in flow direct table are supported now. It is unnecessary since
checking which one is unsupported will be more efficient,
so this patch removes it.

Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for dump MAC ID and loopback status in debugfs

The MAC ID and loopback status information are obtained from
the hardware, which will be helpful for debugging. This patch
adds support for these two items in debugfs.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: move duplicated macro definition into header

Macro HCLGE_GET_DFX_REG_TYPE_CNT in hclge_dbg_get_dfx_bd_num()
and macro HCLGE_DFX_REG_BD_NUM in hclge_get_dfx_reg_bd_num()
have the same meaning, so just defines HCLGE_GET_DFX_REG_TYPE_CNT
in hclge_main.h.

Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor the precedure of PF FLR

Currently, the actual work of PF FLR is handled in the reset task,
which is asynchronous. So in some case, if the preparing and
rebuilding are not done, then the PF FLR will trigger some problems,
for example, makes hardware go into chaos.

So this patch separates the process of PF FLR from reset task, and
adds a semaphore to serialize this reset and others.

When FLR's preparing fails, if there has other higher level reset
pending or failing times less than the HCLGE_FLR_RETRY_CNT, this
preparing should be retried, otherwise PF and its VF may get into
wrong state.

BTW, while the hardware reports misc interrupt during pcie_flr(),
the driver can not receive this interrupt anymore, so disable it
when hclge_flr_prepare() return, and re-enable it when enter
hclge_flr_done().

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove useless mutex vport_cfg_mutex in the struct hclge_dev

Mutex vport_cfg_mutex has been used to protect uc_mac_list,
mc_mac_list and vlan_list from being modified by unloading
or reset task at the same time. But now unloading will
set up HCLGE_STATE_REMOVING flag and call cancel_work_sync to
break down this race condition, so this mutex is unnecessary.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: do not schedule the periodic task when reset fail

service_task will be scheduled per second to do some periodic
jobs. When reset fails, it means this device is not available
now, so the periodic jobs do not need to be handled.

This patch adds flag HCLGE_STATE_RST_FAIL/HCLGEVF_STATE_RST_FAIL
to indicate that reset fails, and checks this flag before
schedule periodic task.

Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove mailbox and reset work in hclge_main

There are three work (mbx_service_task, service_task,
rst_service_task) in the HNS3 driver, mbx_service_task is for
handling mailbox work, service_task is for periodic management
issue and rst_service_task is for reset related issue, which can
be handled in a single work.

This patch removes the mbx_service_task and rst_service_task
work, and moves the related handling to the service_task work
in order to remove concurrency between the three work and to
improve efficiency.

BTW, since stats_timer in struct hclge_hw_stats is not needed
anymore, so removes the definition of struct hclge_hw_stats,
and moves mac_stats into struct hclge_dev.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix a wrong reset interrupt status mask

According to hardware user manual, bits5~7 in register
HCLGE_MISC_VECTOR_INT_STS means reset interrupts status,
but HCLGE_RESET_INT_M is defined as bits0~2 now. So it
will make hclge_reset_err_handle() read the wrong reset
interrupt status.

This patch fixes this wrong bit mask.

Fixes: 2336f19d7892 ("net: hns3: check reset interrupt status when reset fails")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove unused macros

The macros HCLGE_MPF_ENBALE and HCLGEVF_MPF_ENBALE are defined but never
used. I was going to fix the spelling mistake "ENBALE" -> "ENABLE" but
found these macros are not used, so they can be removed.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Use the correct style for SPDX License Identifier

This patch corrects the SPDX License Identifier style in
header files related to Hisilicon network devices. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: cleanup some magic numbers

To make the code more readable, this patch replaces
some magic numbers with macro or sizeof operation.

Also uses macro lower_32_bits and upper_32_bits to
get bits 0-31 and 32-63 of a number, instead of
using type conversion and '>>' operation.

No functional change.

Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: dump some debug information when reset fail

When reset fails, there is some information that will help for
finding out why does reset fail. and removes an unused
core_rst_cnt field in struct hclge_rst_stats.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix mis-counting IRQ vector numbers issue

Currently, the num_msi_left means the vector numbers of NIC,
but if the PF supported RoCE, it contains the vector numbers
of NIC and RoCE(Not expected).

This may cause interrupts lost in some case, because of the
NIC module used the vector resources which belongs to RoCE.

This patch adds a new variable num_nic_msi to store the vector
numbers of NIC, and adjust the default TQP numbers and rss_size
according to the value of num_nic_msi.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for configuring bandwidth of VF on the host

This patch adds support for configuring bandwidth of VF on the host
for HNS3 drivers.

Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: hns3: add support for setting VF trust

This patch adds supports for setting VF trust by host. If specified
VF is trusted, then it can enable promisc(include allmulti mode).
If a trusted VF enabled promisc, and being untrusted, host will
disable promisc mode for this VF.

For VF will update its promisc mode from set_rx_mode now, so it's
unnecessary to set broadcst promisc mode when initialization or
reset.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: hns3: add support for spoof check setting

This patch adds support for spoof check configuration for VFs.
When it is enabled, "spoof checking" is done for both mac address
and VLAN. For each VF, the HW ensures that the source MAC address
(or VLAN) of every outgoing packet exists in the MAC-list (or
VLAN-list) configured for RX filtering for that VF. If not,
the packet is dropped.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: hns3: add support for setting VF link status on the host

This patch adds support to configure VF link properties.
The options are auto, enable, and disable. Even if the PF
is down, the communication between VFs will be normal
if the VFs are set to enable. The commands are as follows:

'ip link set <pf> vf <vf_id> state <auto|enable|disable>'
change the VF status

'ip link show'
show the setting status

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: hns3: add some DFX info for reset issue

This patch adds more information for reset DFX. Also, adds some
cleanups to reset info, move reset_fail_cnt into struct
hclge_rst_stats, and modifies some print formats.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: not allow SSU loopback while execute ethtool -t dev

The current loopback mode is to add 0x1F to the SMAC address
as the DMAC address and enable the promiscuous mode.
However, if the VF address is the same as the DMAC address,
the loopback test fails.

Loopback can be enabled in three places: SSU, MAC, and serdes.
By default, SSU loopback is enabled, so if the SMAC and the DMAC
are the same, the packets are looped back in the SSU. If SSU loopback
is disabled, packets can reach MAC even if SMAC is the same as DMAC.

Therefore, this patch disables the SSU loopback before the loopback
test. In this way, the SMAC and DMAC can be the same, and the
promiscuous mode does not need to be enabled. And this is not
valid in version 0x20.

This patch also uses a macro to replace 0x1F.

Fixes: c39c4d98dc65 ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: check reset interrupt status when reset fails

Currently, the reset interrupt will be cleared firstly, so when
reset fails, if interrupt status register has reset interrupt,
it means there is a new coming reset.

Fixes: 72e2fb07997c ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: implement .process_hw_error for hns3 client

When hardware or IMP get specified error it may need the client
to take some special operations.

This patch implements the hns3 client's process_hw_errorx.

Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: optimize waiting time for TQP reset

This patch optimizes the waiting time for TQP reset.

Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix -Wunused-const-variable warning

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:542:30:
warning: meta_data_key_info defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:553:30:
warning: tuple_key_info defined but not used [-Wunused-const-variable=]

The two variable is only used in hclge_main.c,
so just move the definition over there.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix error and incorrect format

The pointer type parameter should be declare as const for preventing
from its pointed value being unexpected modified.

The uninitialized variable can not be return directly. The default
return value is 0 if no abnormal result.

This patch fixes the preceding two errors, deletes redundant
declaration of a function and align one parameter.

Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add DFX registers information for ethtool -d

Now we can use ethtool -d command to dump some registers. However,
these registers information is not enough to find out where the problem is.

This patch adds DFX registers information after original registers
when use ethtool -d commmand to dump registers. Also, using macro
replaces some related magic number.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add link change event report

Previously, PF updates link status per second. For some scenario,
it requires link down event being reported more quickly.
To solve it, firmware pushes the link change event to PF with
CMDQ message, and driver updates the link status directly.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add interrupt affinity support for misc interrupt

The misc interrupt is used to schedule the reset and mailbox
subtask, and service_task delayed_work is used to do periodic
management work each second.

This patch sets the above three subtask's affinity using the
misc interrupt' affinity.

Also this patch setups a affinity notify for misc interrupt to
allow user to change the above three subtask's affinity.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: make hclge_service use delayed workqueue

Use delayed work instead of using timers to trigger the
hclge_serive.

Simplify the code with one less middle function and in order
to support misc irq affinity.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix race conditions between reset and module loading & unloading

When loading or unloading module, it should wait for the reset task
done before it un-initializes the client, otherwise the reset task
may cause a NULL pointer reference.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: sync VLAN filter entries when kill VLAN ID failed

When HW is resetting, firmware is unable to handle commands
from driver. So if remove VLAN device from stack at this time,
it will fail to remove the VLAN ID from HW VLAN filter, then
the VLAN filter status is unsynced with stack.

This patch fixes it by recording the VLAN ID delete failed,
and removes them again when reset complete.

Fixes: 44e626f720c3 ("net: hns3: fix VLAN offload handle for VLAN inserted by port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: some variable modification

This patch does following things:
1. add the keyword const before some variables which won't be modified
in functions.
2. changes some variables from signed to unsigned to avoid bitwise
operation on signed variables.
3. adds or removes initialization of some variables.
4. defines a new structure to help parsing mailbox messages instead of
using an array which is harder to get the meaning of each element.

Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: use macros instead of magic numbers

This patch adds some macros instead of magic numbers in serval places

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: small changes for magic numbers

In order to improve readability, this patch uses macros to
replace some magic numbers, and adds some comments for some
others.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: don't configure new VLAN ID into VF VLAN table when it's full

VF VLAN table can only support no more than 256 VLANs. When user
adds too many VLANs, the VF VLAN table will be full, and firmware
will close the VF VLAN table for the function. When VF VLAN table
is full, and user keeps adding new VLANs, it's unnecessary to
configure the VF VLAN table, because it will always fail, and print
warning message. The worst case is adding 4K VLANs, and doing reset,
it will take much time to restore these VLANs, which may cause VF
reset fail by timeout.

Fixes: 6c251711b37f ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: use HCLGE_STATE_ROCE_REGISTERED to indicate PF ROCE client has registered

When PF ROCE client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGE_STATE_ROCE_REGISTERED
to indicate that. And before calling PF ROCE client's uninit_instance(),
we clear this state.

So any operation of the ROCE client from HCLGE is not allowed if this
state is not set.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: use HCLGE_STATE_NIC_REGISTERED to indicate PF NIC client has registered

When PF NIC client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGE_STATE_NIC_REGISTERED
to indicate that. And before calling PF NIC client's uninit_instance(),
we clear this state.

So any operation of PF NIC client from HCLGE is not allowed if this
state is not set.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add aRFS support for PF

This patch adds aRFS support for PF. The aRFS rules are also
stored in the hardware flow director table, Use the existing
filter management functions to insert TCPv4/UDPv4/TCPv6/UDPv6
flow director filters. To avoid rule conflict, once user adds
flow director rules with ethtool, the aRFS will be disabled,
and clear exist aRFS rules. Once all user configure rules were
removed, aRFS can work again.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refine the flow director handle

In order to be compatible with aRFS rules, this patch adds
spin_lock for flow director rule adding, deleting, querying,
and packages the rule configuration.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for FEC encoding control

This patch adds support for FEC encoding control, user can change
FEC mode by command ethtool --set-fec, and get FEC mode by command
ethtool --show-fec. The fec capability is changed follow the port
speed. If autoneg on, the user configure fec mode will be overwritten
by autoneg result.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for multiple media type

Previously, we can only identify copper and fiber type, the
supported link modes of port information are always showing
SR type. This patch adds support for multiple media types,
include SR, LR CR, KR. Driver needs to query the media type
from firmware periodicly, and updates the port information.

The new port information looks like this:
Settings for eth0:
Supported ports: [ FIBRE ]
Supported link modes: 25000baseCR/Full
25000baseSR/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Supported FEC modes: None BaseR
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000036 (54)
probe link ifdown ifup
Link detected: yes

In order to be compatible with old firmware which only support
sfp speed, we remained using the same query command, and kept
the former logic.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add handling of MAC tunnel interruption

MAC tnl interruptions are different from other type of RAS and MSI-X
errors, because some bits, such as OVF/LR/RF will occur during link up
and down.

The drivers should clear status of all MAC tnl interruption bits but
shouldn't print any message that would mislead the users.

In case that link down and re-up in a short time because of some reasons,
we record when they occurred, and users can query them by debugfs.

Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add reset statistics info for PF

This patch adds statistics for PF's reset information,
also, provides a debugfs command to dump these statistics.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix for vport->bw_limit overflow problem

When setting vport->bw_limit to hdev->tm_info.pg_info[0].bw_limit
in hclge_tm_vport_tc_info_update, vport->bw_limit can be as big as
HCLGE_ETHER_MAX_RATE (100000), which can not fit into u16 (65535).

So this patch fixes it by using u32 for vport->bw_limit.

Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix set port based VLAN issue for VF

In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.

This patch fixes it. When VF loads up, it firstly queries the port
based VLAN state from PF. When user change port based VLAN state
from PF, PF firstly checks whether the VF is alive. If the VF is
alive, then PF notifies the VF the modification; otherwise PF
configure the port based VLAN state directly.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix set port based VLAN for PF

In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.

Indeed, ndo_set_vf_vlan() is expected to enable or disable port based
VLAN (hardware inserts a specified VLAN tag to all TX packets for a
specified VF) . When enable port based VLAN, we use port based VLAN id
as VLAN filter entry. When disable port based VLAN, we use VLAN id of
VLAN device.

This patch fixes it for PF, enable/disable port based VLAN when calls
ndo_set_vf_vlan().

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: modify VLAN initialization to be compatible with port based VLAN

Our hardware supports inserting a specified VLAN header for each
function when sending packets. User can enable it with command
"ip link set <devname> vf <vfid> vlan <vlan id>".
For this VLAN header is inserted by hardware, not from stack,
hardware also needs to strip it from received packets before
sending to stack. In this case, driver needs to tell
hardware which VLAN to insert or strip.

The current VLAN initialization doesn't allow inserting
VLAN header by hardware, this patch modifies it, in order be
compatible with VLAN inserted base on port.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support to config depth for tx|rx ring separately

This patch adds support to config depth for tx|rx ring separately
by ethtool command "-G".

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Record VF vlan tables

Record the vlan tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.

Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Record VF unicast and multicast tables

Record the unicast and multicast tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.

Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix port info query issue for copper port

In original codes, for copper port which doesn't connect to phy,
it always returns -EOPNOTSUPP when query port information. This
patch fixes it by return the port information of MAC.

Fixes: 5f373b158523 ("net: hns3: Fix speed/duplex information loss problem when executing ethtool ethx cmd of VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: keep flow director state unchanged when reset

In orginal codes, driver always enables flow director when
intializing. When user disable flow director with command
ethtool -K, the flow director will be enabled again after
resetting.

This patch fixes it by only enabling it when first initialzing.

Fixes: 6871af29b3ab ("net: hns3: Add reset handle for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix PFC not setting problem for DCB module

The PFC enabling is based on user priority, currently it is
based on TC, which may cause PFC not setting correctly when pri
to TC mapping is not one to one relation.

This patch adds pfc_en in tm_info to fix it.

Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add statistics for PFC frames and MAC control frames

In the old firmware version, statistics acquisition of
PFC frames and MAC control frames is not supported.
Add command retrieves statistics for PFC frames and
MAC control frames from the firmware.

Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: do reinitialization while ETS configuration changed

When the ETS information is changed, the network device needs to be
re-initialized, otherwise the information such as the receiving queue
will be incorrect.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: getting tx and dv buffer size through firmware

This patch adds support of getting tx and dv buffer size through
firmware, because different version of hardware requires different
size of tx and dv buffer.

This patch also add dv_buf_size to tc' private buffer size even if
pfc is not enable for the tc.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add "queue map" information query function

This patch prints queue map information.

debugfs command:
echo dump queue map > cmd

Sample Command:
root@(none)# echo queue map > cmd
local queue id | global queue id | vector id
0 32 769
1 33 770
2 34 771
3 35 772
4 36 773
5 37 774
6 38 775
7 39 776
8 40 777
9 41 778
10 42 779
11 43 780
12 44 781
13 45 782
14 46 783
15 47 784
root@(none)#

Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add handling of hw errors reported through MSIX

This patch adds handling for HNS3 hardware errors(non-standard)
which are reported through MSIX interrupts and not through
PCIe AER channel.

These MSIX reported hardware errors are handled using common
misc. interrupt handler. Hardware error related registers
cannot be cleared in context to the interrupt received as
they require *heavy* access to hardware using IMP(Integrated
Mangement Processor) commands. Hence, we defer the clearing
of such error events till later time.

Since, we have defered exact identification of errors we
will have to defer the level of receovery/reset which
might be required. Hence, a new reset type UNKNOWN reset
has been introduced which effectively defers the assertion
of the reset till we get hold of kind of errors at later
time.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Adds support to dump(using ethool-d) PCIe regs in HNS3 PF driver

This patch adds support to dump PF PCIe registers using ethtool -d
for HNS3 PF Driver.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Config NIC port speed same as that of optical module

Port 0/1 of HiP08 supports 10G and 25G. This patch adds a
change to configure NIC port speed same as that of optical
module(SFP/QFSP). Driver gets the optical module speed and
sets NIC port speed accordingly.

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add "FD flow table" info query function

All the Flow Director rules are stored in tcam blocks.
For each bit of tcam entry, the match value
depends on two input value(x, y).

debugfs command:
echo dump fd tcam > cmd

Sample output:
root@(none)# echo dump fd tcam > cmd
hns3 0000:7d:00.0: read result tcam key x(31):
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 08000000
hns3 0000:7d:00.0: 00000600
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: read result tcam key y(31):
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: f7ff0000
hns3 0000:7d:00.0: 0000f900
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 0000fff8
root@(none)#

Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add mtu setting support for vf

The patch adds mtu setting support for vf, currently
vf and pf share the same hardware mtu setting. Mtu set
by vf must be less than or equal to pf' mtu, and mtu
set by pf must be greater than or equal to vf' mtu.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add vport alive state checking support

Currently there is no way for pf to know if a vf device is
alive or not, so PF does not know which vf to notify when
reset happens, or which vf's mtu is invalid when vf and pf
share the same hardware mtu setting.

This patch adds vport alive state checking support, in order
to support the above scenario.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Support two vlan header when setting mtu

This patch adds supports for two vlan header when setting mtu.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add PCIe FLR support for PF

This patch implements the .reset_prepare and .reset_done
ops from pci framework to support the PF FLR.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: implement the IMP reset processing for PF

The current code only print the prompt message after receiving
the IMP reset interrupt and does not perform the corresponding driver
reset operation. This patch implements the missing IMP reset handling
in the driver.
1. The driver sets the HCLGE_STATE_CMD_DISABLE to stop sending command
after receiving the IMP reset interrupt.
2. The driver needs to notify the hardware to reload the IMP firmware.
3. The IMP firmware reloading makes the reset time of hardware longer,
so it is necessary to extend the driver's waiting time to wait for
the hardware reset to complete.
4. In hclge_check_event_cause, IMP reset event should have higher
priority than other events.

Also, after clearing HCLGE_STATE_CMD_DISABLE in the hclge_cmd_init(),
it needs to check whether there is a pending reset, if so, just set
the HCLGE_STATE_CMD_DISABLE back and return.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add reset handling for VF when doing PF reset

When PF performs a function reset, the hardware will reset both PF
and all the VF belong to this PF. Hence, both PF's driver and VF's
driver need to perform corresponding reset operations.

Before PF driver asserting function reset to hardware, it firstly
set up VF's hardware reset status, and inform the VF driver with
HNAE3_VF_PF_FUNC_RESET, then VF driver sets this reset type to
reset_pending and shechule reset task to stop IO and waits for the
hardware reset status to clear. When PF driver has reinitialized the
hardware and is ready to process mailbox from VF, PF driver clears
VF's hardware reset status for VF to continue its reset process.

Also, this patch uses readl_poll_timeout to simplify the hardware reset
status waitting.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: adjust VF's reset process

Currently when VF need to reset itself, it will send a cmd to PF,
after receiving the VF reset requset, PF sends a cmd to inform
VF to enter the reset process and send a cmd to firmware to do the
actual reset for the VF, it is possible that firmware has resetted
the VF, but VF has not entered the reset process, which may cause
IO not stopped problem when firmware is resetting VF.

This patch fixes it by adjusting the VF reset process, when VF
need to reset itself, it will enter the reset process first, and
it will tell the PF to send cmd to firmware to reset itself.

Add member reset_pending to struct hclgevf_dev, which indicates that
there is reset event need to be processed by the VF's reset task, and
the VF's reset task chooses the highest-level one and clears other
low-level one when it processes reset_pending.

hclge_inform_reset_assert_to_vf function is unused now, but it will
be used to support the PF reset with VF working, so declare it in
the header file.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add error handler for hclge_reset()

When hclge_reset() is called, it may fail for several reasons.
For example, an higher-level reset event occurs, memory allocation
failure, hardware reset timeout, etc. Therefore, it is necessary
to add corresponding error handling for these situations.
1. A high-level reset is required due to a high-level reset failure.
2. For memory allocation failure, a high-level reset is initiated by
the timer to recover. The reason for using the timer is to prevent this
new high-level reset to interrupt the reset process of other pf/vf;
3. For the case of hardware reset timeout, reschedule the reset task
to wait for the hardware to complete the reset.
For memory allocation failure and reset timeouts, in order to prevent
an infinite number of scheduled reset tasks, the number of error
recovery needs to be limited.

This patch also add some reset related debug log printing.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: move some reset information from hnae3_handle into hclge_dev/hclgevf_dev

Saving reset related information in the hclge_dev/hclgevf_dev
structure is more suitable than the hnae3_handle, since hardware
related information is kept in these two structure.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: provide some interface & information for the client

The client needs to know if the hardware is resetting when
loading or unloading itself, because client may abort the loading
process or wait for the reset process to finish when unloading
if hardware is resetting.

So this patch provides these interfaces to do it.
1. get_hw_reset_stat, the reset status of hardware.
2. ae_dev_resetting, whether reset task is scheduling.
3. ae_dev_reset_cnt, how many reset has been done.

Also, the RoCE client needs some field in the hnae3_roce_private_info
to save its state, and process_hw_error interface in the
hnae3_client_ops to process hardware errors.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add set_default_reset_request in the hnae3_ae_ops

Currently, when reset_event is called because of tx timeout, it will
upgrade the reset level (For PF, HNAE3_FUNC_RESET -> HNAE3_CORE_RESET
-> HNAE3_GLOBAL_RESET) if the time between the new reset and last reset
is within 20 secs, or restore the reset level to HNAE3_FUNC_RESET if
the time between the new reset and last reset is over 20 secs.

There is requirement that the caller needs to decide the reset level
when triggering a reset, for example, RAS recovery. So this patch
adds the set_default_reset_request to meet this requirement.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix incorrect return value/type of some functions

There are some functions that, when they fail to send the command,
need to return the corresponding error value to its caller.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: 681ec3999b3d ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Drop depricated mta table support

For mta table support has been dropped, remove the code for mta table.

Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Optimize for unicast mac vlan table

In previously implement for unicast mac vlan table, the space is
shared by all the functions, driver does nothing when the space is
exhausted. This patch preallocates the space of unicast mac vlan
table for each function by software. Each function can only use its
private space and available shared space, avoiding single function
exhausts too much space, and other functions are unable to add
unicast mac address.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add support for rule add/delete for flow director

This patch adds support for add and delete rule by ethtool commands.
HNS3 driver supports several flow types, include ETHER_FLOW,
IP_USER_FLOW, TCP_V4_FLOW, UDP_V4_FLOW, SCTP_V4_FLOW, IPV6_USER_FLOW,
TCP_V6_FLOW, UDP_V6_FLOW and SCTP_V6_FLOW.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add input key and action config support for flow director

Each flow director rule consists of input key and action. The input key
is the condition for matching, includes tuples of L2/L3/L4 header.
Action is the behaviour when a packet matches with the input key, such
as drop the packet, or forward to a specified queue.

The input key is stored in the tcam blocks, Each bit of input key can
be masked.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add flow director initialization

Flow director is a new feature supported by hardware with revision 0x21.
This patch adds flow direcor initialization for each PF. It queries flow
director mode and tcam resource from firmware, selects tuples used for
input key.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Remove packet statistics of public

All pf have permission to read packet statistics of public in hardware,
but the read operation will clear registers which cause statistical
inaccuracy.

This patch removes all packet statistics of public.

Signed-off-by: Junxin Chen <chenjunxin1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Refine the MSIX allocation for PF

The offset of msix number for roce is different between different
revision id. We should get it from firmware, instead of a fix value.
This patch refines the msix allocation, make it compatible.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add SPDX tags to HNS3 PF driver

Add the SPDX identifiers to HNS3 PF driver.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Remove unused struct member and definition

The struct hclge_desc_cb and hclge_desc_cb are never used in
anywhere. This patch removes them.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Modify inconsistent bit mask macros

Use BIT() and GENMASK() to convert the bit mask, modify
the inconsistent ones, and remove useless ones.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Use decimal for bit offset macros

Using hex for bit offsets is inconsistent with the rest
of the file. Change them to decimal.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Correct unreasonable code comments

This patch fixes some comment spelling errors, removes
redundant comments, rewrites misleading comments, and
adds some necessary comments.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Remove extra space and brackets

Remove extra space and brackets.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Correct reset event status register

According to hardware's description, driver should get reset event
from VECTOR0_PF_OTHER_INT_ST(0x20800) instead of
VECTOR0_PF_OTHER_INT_SRC(0x20700).

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Prevent sending command during global or core reset

According to hardware's description, driver should not send command to
IMP while hardware doing global or core reset.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove back in struct hclge_hw

hclge_hw is embedded in hclge_dev, so use container_of instead of
back to get hclge_dev.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Optimize the PF's process of updating multicast MAC

In the current process, the multicast MAC is added to both MAC_VLAN
table and MTA table, this will reduce the utilization of the resource.

This patch improves the process of adding multicast MAC address, the
new process starts using the MTA table to add multicast MAC after the
MAC_VLAN table is full, and the MTA is disable if it is no longer used.

Signed-off-by: Xi Wang <wangxi11@huawei.com>
Reviewed-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Remove unused led control code

In the previous implementation of led control for fibre port , parses the
port speed configuration, checks the link status and traffic status per
second, and updates the blink status of link led, traffic led and speed
led.

Now, the firmware takes responsibility to handle the led, the dirver just
needs to deal with locate command.

So the codes for link led, traffic led and speed led are useless now. This
patch removes these redundant codes.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add support for tx_accept_tag2 and tx_accept_untag2 config

HNS3 Hardware can support up to two VLAN tags in transmit leg, the PPP
module can handle the packets based on the tag1 and tag2 config. This
patch adds support for tag2 config for vlan handling

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix for hns3 module is loaded multiple times problem

If the hns3 driver has been built into kernel and then loaded with
the same driver which built as KLM, it may trigger an error like
below:

[ 20.009555] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[ 20.016789] hns3: Copyright (c) 2017 Huawei Corporation.
[ 20.022100] Error: Driver 'hns3' is already registered, aborting...
[ 23.517397] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 23.691583] Process insmod (pid: 1982, stack limit = 0x00000000cd5f21cb)
[ 23.698270] Call trace:
[ 23.700705] __list_del_entry_valid+0x2c/0xd8
[ 23.705049] hnae3_unregister_client+0x68/0xa8
[ 23.709487] hns3_init_module+0x98/0x1000 [hns3]
[ 23.714093] do_one_initcall+0x5c/0x170
[ 23.717918] do_init_module+0x64/0x1f4
[ 23.721654] load_module+0x1d14/0x24b0
[ 23.725390] SyS_init_module+0x158/0x208
[ 23.729300] el0_svc_naked+0x30/0x34

This patch fixes it by adding module version info.

Fixes: 38caee9d3ee8 ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add support of hardware rx-vlan-offload to HNS3 VF driver

This patch adds support of hardware rx-vlan-offload to VF driver.
VF uses mailbox to convey PF to configure the hardware.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Remove packet statistics in the range of 8192~12287

Because the current statistics for size 8192~12287 are only valid for GE,
the ranges of 8192~9216 and 9217~12287 are valid only for LGE/CGE, and are
always 0 for GE interfaces. it is easy to cause confusion when viewing the
packet statistics using the command ethtool -S.

This patch removes the 8192~12287 range of packet statistics and uses the
8192~9216 and 9217~12287 ranges for statistics. This change depends on the
firmware upgrade.

Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix for packet loss due wrong filter config in VLAN tbls

There are two level of vlan tables in hardware, one is port vlan
which is shared by all functions, the other one is function
vlan table, each function has it's own function vlan table.
Currently, PF sets the port vlan table, and vf sets the function
vlan table, which will cause packet lost problem.

This patch fixes this problem by setting both vlan table, and
use hdev->vlan_table to manage thet port vlan table.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Changes required in PF mailbox to support VF reset

PF needs to assert the VF reset when it receives the request to
reset from VF. After receiving request PF ackknowledges the
request by replying back MBX_ASSERTING_RESET message to VF.
VF then goes to pending state and wait for hardware to complete
the reset.

This patch contains code to handle the received VF message, inform
the VF of assertion and reset the VF using cmdq interface.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix for getting wrong link mode problem

Fixed link mode is returned by hns3_get_link_ksettings. It is
unreasonable.

This patch fixes it by adding some related functions to get link
mode from hardware.

Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix the VF queue reset flow error

VF queue reset flow is different from PF queue reset flow.
VF driver should stop VF queue first, then send message to PF
and PF do the reset. PF should send a response to VF after
PF complete the queue reset, VF can initialize the queue hw
after get the response.
This patch fixes the VF queue reset flow as the correct step.

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix for RSS configuration loss problem during reset

RSS configuration will be set to default value by hclge_rss_init_hw
during reset, which causes the RSS configuration loss problem.

This patch fixes it by setting the default value in
hclge_rss_init_cfg function, which will not be called in the reset
process.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor the hclge_get/set_rss_tuple function

This patch refactors the hclge_get/set_rss_tuple function
in order to fix the rss configuration loss problem during
reset process.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor the hclge_get/set_rss function

This patch refactors the hclge_get/set_rss function in
order to fix the rss configuration loss problem during
reset process.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add net status led support for fiber port

Check the net status per second, include port speed, total rx/tx packets
and link status. Updating the led status for fiber port.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add more packet size statisctics

The statistics of rx/tx packets size greater than 1518
are not detailed. This patch adds more statistics for
different packet size range.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix for setting MTU

When setting MTU, actually what we do is configuring the max frame size
for the hardware. ETH_HLEN、ETH_FCS_LEN and VLAN_HLEN must need to be
considered. And the frame size which is less than the default value
should not be set to the hardware. Because in the hardware, the the max
frame size not only controls the RX packet size, but also controls the
TX packet size. the RX packets whose size are greater than the setting
value will be dropped.

This patch fixes the bug setting a error max frame size to hardware.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Modify the update period of packet statistics

It takes more than 200 query response messages between
driver and IMP, while updating the packet statistics.
It's too heavy for IMP to update it per second.

Extend the update period of packet statistics data from
1 second to 300 seconds(if too long, the statistics may
overflow).

As a result, we need to update it while querying with
ifconfig tool to keep the statistics data fresh.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix spelling errors

Fix spelling error "overrsize" --> "oversize".

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Unify the strings display of packet statistics

Some members of packet statistics are named in different styles.
This patch unifies them with new internal name rules, the main
modification are below:
trans --> tx
rcv --> rx
rcb_q%d_tx --> txq#%d
rcb_q%d_rx --> rxq#%d
sw_err_cnt(tx side) --> tx_dropped
sw_err_cnt(rx side) --> rx_dropped
pkts --> packets
tx_err_cnt --> errors
rx_err_cnt --> errors

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support to update flow control settings after autoneg

When auto-negotiation is enabled, the MAC flow control settings is
based on the flow control negotiation result. And it should be configured
after a valid link has been established. This patch adds support to update
flow control settings after auto-negotiation has completed.

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add vlan offload config command

This patch adds vlan offload config commands, initializes
the rules of tx/rx vlan tag handle for hw.

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: get rss_size_max from configuration but not hardcode

Add configuration for rss_size_max in hdev but not hardcode it.

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Mingguang Qu <qumingguang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add mailbox interrupt handling to PF driver

All PF mailbox events are conveyed through a common interrupt
(vector 0). This interrupt vector is shared by reset and mailbox.

This patch adds the handling of mailbox interrupt event and its
deferred processing in context to a separate mailbox task.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Change PF to add ring-vect binding & resetQ to mailbox

This patch is required to support ring-vector binding and reset
of TQPs requested by the VF driver to the PF driver. Mailbox
handler is added with corresponding VF commands/messages to
handle the request.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add mailbox support to PF driver

Command queue provides the provision of Mailbox command which
can be used for communication between PF and VF. PF handles
messages from various VFs for fetching various information like,
queue, vlan, link status related etc. It also handles the request
from various VFs to perform certain privileged operations.

This patch adds the support of a message handler for handling
such various command requests from VF.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Refactors the requested reset & pending reset handling code

In exisiting code, the way to detect if driver/client reset should
be executed or if hardware should be be soft resetted was overly
complex.

Existing code use to read the interrupt status register from task
context to figure out if the interrupt source event was reset and
then use clear the interrupt source for reset while waiting for the
hardware to finish the reset. This behaviour again was confusing
and overly complex in terms of the flow.

This patch simplifies the handling of the requested reset and the
pending reset(i.e. reset which have already been asserted by the
software and hardware has acknowledged back to driver that it is
processing the hardware reset through interrupt)

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add reset service task for handling reset requests

Existing common service task was being used to service the reset
requests. This patch tries to make the handling of reset cleaner
by separating task to handle the reset requests. This might in
turn help in adapting similar handling approach for other
interrupt events like mailbox, sharing vector 0 interrupt.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Refactor of the reset interrupt handling logic

The reset interrupt event shares common miscellaneous interrupt
Vector 0. In the existing reset interrupt handling we disable
the Vector 0 interrupt in misc interrupt handler and re-enable
them later in context to common service task.

This also means other event sources like mailbox would also be
deferred or if the interrupt event was due to mailbox(which shall
be supported for VF soon), it could delay the reset handling.

This patch reorganizes the reset interrupt handling logic and
makes it more fair to other events.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Updates MSI/MSI-X alloc/free APIs(depricated) to new APIs

This patch migrates the HNS3 driver code from use of depricated PCI
MSI/MSI-X interrupt vector allocation/free APIs to new common APIs.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add reset process in hclge_main

This patch adds reset support for PF,it include : global reset, core reset,
IMP reset, PF reset.The core reset will Reset all datapath of all functions
except IMP, MAC and PCI interface. Global reset is equal with the core
reset plus all MAC reset. IMP reset is caused by watchdog timer expiration,
the same with core reset in the reset flow. PF reset will reset whole
physical function.

Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add support for misc interrupt

This patch adds initialization and deinitialization for misc interrupt.
This interrupt will be used to handle reset message(IRQ).

Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add mqprio hardware offload support in hns3 driver

When using tc qdisc, dcb_ops->setup_tc is used to tell hclge_dcb
module to do the tm related setup. Only TC_MQPRIO_MODE_CHANNEL
offload mode is supported.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for set_rxnfc

This patch supports the ethtool's set_rxnfc().

Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Consistently using GENMASK in hns3 driver

This patch uses GENMASK to generate bit mask whenever
possible in hns3 driver.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add hclge_dcb module for the support of DCB feature

The hclge_dcb module calls the interface from hclge_main/tm
and provide interface for the dcb netlink interface.

This patch also update Makefiles required to build the DCB
supported code in HNS3 Ethernet driver and update the existing
Kconfig file in the hisilicon folder.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add some interface for the support of DCB feature

This patch add some interface and export some interface from
hclge_tm and hclgc_main to support the upcoming DCB feature.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add support for dynamically buffer reallocation

Current buffer allocation can only happen at init, when
doing buffer reallocation after init, care must be taken
care of memory which priv_buf points to.
This patch fixes it by using a dynamic allocated temporary
memory. Because we only do buffer reallocation at init or
when setting up the DCB parameter, and priv_buf is only
used at buffer allocation process, so it is ok to use a
dynamic allocated temporary memory.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix for pri to tc mapping in TM

Current mapping between pri and tc is one to one,
so user can't map multi priorities to the same tc.
This patch changes the mapping to many to one.

Fixes: 848440544b41f ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix for setting rss_size incorrectly

rss_size is 1, 2, 4, 8, 16, 32, 64, 128, but acutal tc queue
size can be any u16 less than 128. If tc queue size is 5, we
set the rss_size to 8, indirection table will be used to limit
the size of actual queue size.
It may cause dropping of receiving packet in hardware if
rss_size is not set correctly.
For now, each TC has the same rss size.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support

This patch adds the support of Hisilicon Network Subsystem Accceleration
Engine and common operations to access it. This layer provides access to the
hardware configuration, hardware statistics. This layer is also
responsible for triggering the initialization of the PHY layer through
the below MDIO layer.

Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>