net: dpaa2-eth: update the dpni_set_pools() API to support per QDBIN pools

Update the dpni_set_pool() firmware API so that in the next patches we
can configure per Rx queue (per QDBIN) buffer pools.
This is a hard requirement of the AF_XDP, thus we need the newer API
version.

Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: Update dpni_get_single_step_cfg command

dpni_get_single_step_cfg is an MC firmware command used for
retrieving the contents of SINGLE_STEP 1588 register available
in a DPMAC.

This patch adds a new version of this command that returns as an extra
argument the physical base address of the aforementioned register.
The address will be used to directly modify the contents of the
SINGLE_STEP register instead of invoking the MC command
dpni_set_single_step_cgf. The former approach introduced huge delays on
the TX datapath when one step PTP events were transmitted. This led to low
throughput and high latencies observed in the PTP correction field.

Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: add support for Rx VLAN filtering

Declare Rx VLAN filtering as supported and user-changeable only when
there are VLAN filtering entries available on the DPNI object. Even
then, rx-vlan-filtering is by default disabled.
Also, populate the .ndo_vlan_rx_add_vid() and .ndo_vlan_rx_kill_vid()
callbacks for adding and removing a specific VLAN from the VLAN table.

Signed-off-by: Ionut-robert Aron <ionut-robert.aron@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20210111170725.1818218-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

dpaa2-eth: fix command version for Tx shaping

When adding the support for TBF offload, the improper command version
was added even though the command format is for the V2 of
dpni_set_tx_shaping(). This does not affect the functionality of TBF
since the only change between these two versions is the addition of the
exceeded parameters which are not used in TBF. Still, fix the bug so
that we keep things in sync.

Fixes: 39344a89623d ("dpaa2-eth: add API for Tx shaping")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: add APIs of 1588 single step timestamping

This patch is to add APIs of 1588 single step timestamping.

- dpni_set_single_step_cfg
- dpni_get_single_step_cfg

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: add API for Tx shaping

Add the necessary API (dpni_set_tx_shaping) for configuring the rate and
burst size of a per port shaper in DPAA2.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: Add PFC support through DCB ops

Add support in dpaa2-eth for PFC (Priority Flow Control)
through the DCB ops.

Instruct the hardware to respond to received PFC frames.
Current firmware doesn't allow us to selectively enable PFC
on the Rx side for some priorities only, so we will react to
all incoming PFC frames (and stop transmitting on the traffic
classes specified in the frame).

Also, configure the hardware to generate PFC frames based on Rx
congestion notifications. When a certain number of frames accumulate in
the ingress queues corresponding to a traffic class, priority flow
control frames are generated for that TC.

The number of PFC traffic classes available can be queried through
lldptool. Also, which of those traffic classes have PFC enabled is also
controlled through the same dcbnl_rtnl_ops callbacks.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: Distribute ingress frames based on VLAN prio

Configure static ingress classification based on VLAN PCP field.
If the DPNI doesn't have enough traffic classes to accommodate all
priority levels, the lowest ones end up on TC 0 (default on miss).

Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: Add pause frame support

Starting with firmware version MC10.18.0, we have support for
L2 flow control. Asymmetrical configuration (Rx or Tx only) is
supported, but not pause frame autonegotioation.

Pause frame configuration is done via ethtool. By default, we start
with flow control enabled on both Rx and Tx. Changes are propagated
to hardware through firmware commands, using two flags (PAUSE,
ASYM_PAUSE) to specify Rx and Tx pause configuration, as follows:

PAUSE | ASYM_PAUSE | Rx pause | Tx pause
----------------------------------------
0 | 0 | disabled | disabled
0 | 1 | disabled | enabled
1 | 0 | enabled | enabled
1 | 1 | enabled | disabled

The hardware can automatically send pause frames when the number
of buffers in the pool goes below a predefined threshold. Due to
this, flow control is incompatible with Rx frame queue taildrop
(both mechanisms target the case when processing of ingress
frames can't keep up with the Rx rate; for large frames, the number
of buffers in the pool may never get low enough to trigger pause
frames as long as taildrop is enabled). So we set pause frame
generation and Rx FQ taildrop as mutually exclusive.

Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: Add ethtool support for flow classification

Add support for inserting and deleting Rx flow classification
rules through ethtool.

We support classification based on some header fields for
flow-types ether, ip4, tcp4, udp4 and sctp4.

Rx queues are core affine, so the action argument effectively
selects on which cpu the matching frame will be processed.
Discarding the frame is also supported.

Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: Configure Rx flow classification key

For firmware versions that support it, configure an Rx flow
classification key at probe time.

Hardware expects all rules in the classification table to share
the same key. So we setup a key containing all supported fields
at driver init and when a user adds classification rules through
ethtool, we will just mask out the unused header fields.

Since the key composition process is the same for flow
classification and hashing, reuse existing code where possible.

Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: Use new API for Rx flow hashing

The Management Complex (MC) firmware initially allowed the
configuration of a single key to be used both for Rx flow hashing
and flow classification. This prevented us from supporting
Rx flow classification through ethtool.

Starting with version 10.7.0, the Management Complex(MC) offers
a new set of APIs for separate configuration of Rx hashing and
classification keys.

Update the Rx flow hashing support to use the new API, if available.

Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: Move DPAA2 Ethernet driver from staging to drivers/net

The DPAA2 Ethernet driver supports Freescale/NXP SoCs with DPAA2
(DataPath Acceleration Architecture v2). The driver manages
network objects discovered on the fsl-mc bus.

Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>