net: dpaa: Convert to phylink

This converts DPAA to phylink. All macs are converted. This should work
with no device tree modifications (including those made in this series),
except for QSGMII (as noted previously).

The mEMAC configuration is one of the tricker areas. I have tried to
capture all the restrictions across the various models. Most of the time,
we assume that if the serdes supports a mode or the phy-interface-mode
specifies it, then we support it. The only place we can't do this is
(RG)MII, since there's no serdes. In that case, we rely on a (new)
devicetree property. There are also several cases where half-duplex is
broken. Unfortunately, only a single compatible is used for the MAC, so we
have to use the board compatible instead.

The 10GEC conversion is very straightforward, since it only supports XAUI.
There is generally nothing to configure.

The dTSEC conversion is broadly similar to mEMAC, but is simpler because we
don't support configuring the SerDes (though this can be easily added) and
we don't have multiple PCSs. From what I can tell, there's nothing
different in the driver or documentation between SGMII and 1000BASE-X
except for the advertising. Similarly, I couldn't find anything about
2500BASE-X. In both cases, I treat them like SGMII. These modes aren't used
by any in-tree boards. Similarly, despite being mentioned in the driver, I
couldn't find any documented SoCs which supported QSGMII. I have left it
unimplemented for now.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dpaa_eth: remove dead select in menuconfig FSL_DPAA_ETH

The menuconfig FSL_DPAA_ETH selects config FSL_FMAN_MAC, but the config
FSL_FMAN_MAC never existed in the kernel tree.

Hence, ./scripts/checkkconfigsymbols.py warns:

FSL_FMAN_MAC
Referencing files: drivers/net/ethernet/freescale/dpaa/Kconfig

Remove this dead select in menuconfig FSL_DPAA_ETH.

Fixes: 9ad1a3749333 ("dpaa_eth: add support for DPAA Ethernet")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

treewide: replace '---help---' in Kconfig files with 'help'

Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.

This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.

There are a variety of indentation styles found.

a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'

In order to convert all of them to 1 tab + 'help', I ran the
following commend:

$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

net: freescale: select CONFIG_FIXED_PHY where needed

I ran into a randconfig build failure with CONFIG_FIXED_PHY=m
and CONFIG_GIANFAR=y:

x86_64-linux-ld: drivers/net/ethernet/freescale/gianfar.o:(.rodata+0x418): undefined reference to `fixed_phy_change_carrier'

It seems the same thing can happen with dpaa and ucc_geth, so change
all three to do an explicit 'select FIXED_PHY'.

The fixed-phy driver actually has an alternative stub function that
theoretically allows building network drivers when fixed-phy is
disabled, but I don't see how that would help here, as the drivers
presumably would not work then.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dpaa_eth: remove redundant dependency on FSL_SOC

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa_eth: add support for DPAA Ethernet

This introduces the Freescale Data Path Acceleration Architecture
(DPAA) Ethernet driver (dpaa_eth) that builds upon the DPAA QMan,
BMan, PAMU and FMan drivers to deliver Ethernet connectivity on
the Freescale DPAA QorIQ platforms.

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>