bnxt_en: Define BNXT_VNIC_DEFAULT for the default vnic index

Replace hard coded 0 index with more meaningful BNXT_VNIC_DEFAULT.

Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Add RSS support for IPSEC headers

IPSec uses two distinct protocols, Authentication Header (AH) and
Encapsulating Security Payload (ESP).
Add support to configure RSS based on AH and ESP headers.
This functionality will be enabled based on the capabilities
indicated by the firmware in HWRM_VNIC_QCAPS.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-14-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Invalidate user filters when needed

The cached user filters slated to be reapplied need to
be cleared if configured MAC changes, RSS key changes,
number of rings changes, or ntuple is disabled.

Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-13-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Add support for user configured RSS key

Store the user configured or generated Toeplitz key in
bp->rss_hash_key. The key stays constant across ifdown/ifup
unless updated by the user.

Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-12-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Add drop action support for ntuple

Add drop action for protocols TCP/UDP/ICMP
1) Drop action for TCP/UDP is supported via flow type
tcp4/udp4/tcp6/udp6.
2) Drop action for ICMPV4/ICMPV6/wildcard is supported
via flow type ipv4/ipv6.

Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-7-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Enhance ethtool ntuple support for ip flows besides TCP/UDP

Enable flow type ipv4/ipv6
1) for protocols ICMPV4 and ICMPV6.
2) for wildcard match. Wildcard matches to TCP/UDP/ICMP.
Note that, IPPROTO_RAW(255) i.e. a reserved protocol
considered for a wildcard.

Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-6-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: implement fully specified 5-tuple masks

Support subfield masking for IP addresses and ports. Previously, only
entire fields could be included or excluded in NTUPLE filters.

Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://lore.kernel.org/r/20240205223202.25341-5-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Support ethtool -n to display ether filters.

Implement ETHTOOL_GRXCLSRULE for the user defined ether filters. Use
the common functions to walk the L2 filter hash table.

Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://lore.kernel.org/r/20240205223202.25341-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Add ethtool -N support for ether filters.

Add ETHTOOL_SRXCLSRLINS and ETHTOOL_SRXCLSRLDEL support for inserting
and deleting L2 ether filter rules. Destination MAC address and
optional VLAN are supported for each filter entry. This is currently
only supported on older BCM573XX and BCM574XX chips only.

Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Use firmware provided maximum filter counts.

While individual filter structures are allocated as needed, there is an
array to keep track of the software filter IDs that we allocate ahead
of time. Rather than relying on a fixed maximum filter count to
allocate this array, get the maximum from the firmware when available.

Move these filter related maximum counts queried from the firmware to the
bnxt_hw_resc struct. If the firmware is not providing these maximum
counts, fall back to the hard-coded constant.

Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://lore.kernel.org/r/20240205223202.25341-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt: convert EEE handling to use linkmode bitmaps

Convert EEE handling to use linkmode bitmaps. This prepares for removing
the legacy bitmaps from struct ethtool_keee. No functional change
intended. When replacing _bnxt_fw_to_ethtool_adv_spds() with
_bnxt_fw_to_linkmode(), remove the fw_pause argument because it's
always passed as 0.

Note:
There's a discussion on whether the underlying implementation is correct,
but it's independent of this mechanical conversion w/o functional change.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/9123bf18-a0d0-404e-a7c4-d6c466b4c5e8@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ethtool: add suffix _u32 to legacy bitmap members of struct ethtool_keee

This is in preparation of using the existing names for linkmode
bitmaps.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: replace struct ethtool_eee with a new struct ethtool_keee on kernel side

In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix possible crash after creating sw mqprio TCs

The driver relies on netdev_get_num_tc() to get the number of HW
offloaded mqprio TCs to allocate and free TX rings. This won't
work and can potentially crash the system if software mqprio or
taprio TCs have been setup. netdev_get_num_tc() will return the
number of software TCs and it may cause the driver to allocate or
free more TX rings that it should. Fix it by adding a bp->num_tc
field to store the number of HW offload mqprio TCs for the device.
Use bp->num_tc instead of netdev_get_num_tc().

This fixes a crash like this:

BUG: kernel NULL pointer dereference, address: 0000000000000000
PGD 42b8404067 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 120 PID: 8661 Comm: ifconfig Kdump: loaded Tainted: G OE 5.18.16 #1
Hardware name: Lenovo ThinkSystem SR650 V3/SB27A92818, BIOS ESE114N-2.12 04/25/2023
RIP: 0010:bnxt_hwrm_cp_ring_alloc_p5+0x10/0x90 [bnxt_en]
Code: 41 5c 41 5d 41 5e c3 cc cc cc cc 41 8b 44 24 08 66 89 03 eb c6 e8 b0 f1 7d db 0f 1f 44 00 00 41 56 41 55 41 54 55 48 89 fd 53 <48> 8b 06 48 89 f3 48 81 c6 28 01 00 00 0f b6 96 13 ff ff ff 44 8b
RSP: 0018:ff65907660d1fa88 EFLAGS: 00010202
RAX: 0000000000000010 RBX: ff4dde1d907e4980 RCX: f400000000000000
RDX: 0000000000000010 RSI: 0000000000000000 RDI: ff4dde1d907e4980
RBP: ff4dde1d907e4980 R08: 000000000000000f R09: 0000000000000000
R10: ff4dde5f02671800 R11: 0000000000000008 R12: 0000000088888889
R13: 0500000000000000 R14: 00f0000000000000 R15: ff4dde5f02671800
FS: 00007f4b126b5740(0000) GS:ff4dde9bff600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000416f9c6002 CR4: 0000000000771ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
bnxt_hwrm_ring_alloc+0x204/0x770 [bnxt_en]
bnxt_init_chip+0x4d/0x680 [bnxt_en]
? bnxt_poll+0x1a0/0x1a0 [bnxt_en]
__bnxt_open_nic+0xd2/0x740 [bnxt_en]
bnxt_open+0x10b/0x220 [bnxt_en]
? raw_notifier_call_chain+0x41/0x60
__dev_open+0xf3/0x1b0
__dev_change_flags+0x1db/0x250
dev_change_flags+0x21/0x60
devinet_ioctl+0x590/0x720
? avc_has_extended_perms+0x1b7/0x420
? _copy_from_user+0x3a/0x60
inet_ioctl+0x189/0x1c0
? wp_page_copy+0x45a/0x6e0
sock_do_ioctl+0x42/0xf0
? ioctl_has_perm.constprop.0.isra.0+0xbd/0x120
sock_ioctl+0x1ce/0x2e0
__x64_sys_ioctl+0x87/0xc0
do_syscall_64+0x59/0x90
? syscall_exit_work+0x103/0x130
? syscall_exit_to_user_mode+0x12/0x30
? do_syscall_64+0x69/0x90
? exc_page_fault+0x62/0x150

Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240117234515.226944-6-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Fix RSS table entries calculation for P5_PLUS chips

The existing formula used in the driver to calculate the number of RSS
table entries is to round up the number of RX rings to the next integer
multiples of 64 (e.g. 64, 128, 192, ..). This is incorrect. The valid
values supported by the chip are 64, 128, 256, 512 only (power of 2
starting from 64). When the number of RX rings is greater than 128, the
entry size will likely be wrong. Firmware will round down the invalid
value (e.g. 192 rounded down to 128) provided by the driver, causing some
RSS rings to not receive any packets.

We already have an existing function bnxt_calc_nr_ring_pages() to
do this calculation. Use it in bnxt_get_nr_rss_ctxs() to calculate the
number of RSS contexts correctly for P5_PLUS chips.

Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Fixes: 7b3af4f75b81 ("bnxt_en: Add RSS support for 57500 chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240117234515.226944-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Fix RCU locking for ntuple filters in bnxt_srxclsrldel()

After looking up an ntuple filter from a RCU hash list, the
rcu_read_unlock() call should be made after reading the structure,
or after determining that the filter cannot age out (by aRFS).
The existing code was calling rcu_read_unlock() too early in
bnxt_srxclsrldel().

As suggested by Simon Horman, change the code to handle the error
case of fltr_base not found in the if condition. The code looks
cleaner this way.

Fixes: 8d7ba028aa9a ("bnxt_en: Add support for ntuple filter deletion by ethtool.")
Suggested-by: Simon Horman <horms@kernel.org>
Reported-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/netdev/20240104145955.5a6df702@kernel.org/
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240105235439.28282-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Add support for ntuple filter deletion by ethtool.

Add logic to delete a user specified ntuple filter from ethtool.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add support for ntuple filters added from ethtool.

Add support for adding user defined ntuple TCP/UDP filters. These
filters are similar to aRFS filters except that they don't get aged.
Source IP, destination IP, source port, or destination port can be
unspecifed as wildcard. At least one of these tuples must be specifed.
If a tuple is specified, the full mask must be specified.

All ntuple related ethtool functions are now no longer compiled only
for CONFIG_RFS_ACCEL.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add ntuple matching flags to the bnxt_ntuple_filter structure.

aRFS filters match all 5 tuples. User defined ntuple filters may
specify some of the tuples as wildcards. To support that, we add the
ntuple_flags to the bnxt_ntuple_filter struct to specify which tuple
fields are to be matched. The matching tuple fields will then be
passed to the firmware in bnxt_hwrm_cfa_ntuple_filter_alloc() to create
the proper filter.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Refactor the hash table logic for ntuple filters.

Generalize the ethtool logic that walks the ntuple hash table now that
we have the common bnxt_filter_base structure. This will allow the code
to easily extend to cover user defined ntuple or ether filters.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Refactor bnxt_ntuple_filter structure.

This is in preparation to support user defined L2 (ether) filters,
which will have many similarities with ntuple filters. Refactor
bnxt_ntuple_filter structure to have a bnxt_filter_base structure
that can be re-used by the L2 filters.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethtool: pass a pointer to parameters to get/set_rxfh ethtool ops

The get/set_rxfh ethtool ops currently takes the rxfh (RSS) parameters
as direct function arguments. This will force us to change the API (and
all drivers' functions) every time some new parameters are added.

This is part 1/2 of the fix, as suggested in [1]:

- First simplify the code by always providing a pointer to all params
(indir, key and func); the fact that some of them may be NULL seems
like a weird historic thing or a premature optimization.
It will simplify the drivers if all pointers are always present.

- Then make the functions take a dev pointer, and a pointer to a
single struct wrapping all arguments. The set_* should also take
an extack.

Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-2-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: add rx_filter_miss extended stats

rx_filter_miss counter is newly added to the rx_port_stats_ext
stats structure for newer chips. Newer firmware will return the
structure size that includes this counter. Add this entry to
the bnxt_port_stats_ext_arr array and the ethtool -S code will
pick up this counter if it is supported.

Signed-off-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231212005122.2401-11-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Report the new ethtool link modes in the new firmware interface

Add new look up entries to convert the new supported speeds, advertised
speeds, etc to ethtool link modes.

Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231201223924.26955-15-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Support force speed using the new HWRM fields

Modify bnxt_force_link_speed() to support the new speeds stored in
link_info->support_speeds2, including the new 400G speed.

Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231201223924.26955-14-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Support new firmware link parameters

Newer firmware supporting PAM4 112Gbps speeds use new parameters in
firmware message structures. Detect the new firmware capability and
add basic logic to report and store these new fields.

Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231201223924.26955-13-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Refactor ethtool speeds logic

Add helper functions to refactor the logic that converts firmware
speed masks to ethtool speeds. Pass the phy_flags to
bnxt_get_ethtool_speeds() and the call chain. The refactoring and the
phy_flags will be needed when adding support for the new speeds in the
next patches.

Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231201223924.26955-12-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Add support for new RX and TPA_START completion types for P7

These new completion types are supported on the new P7 chips.
These new types have commonalities with the legacy types. After
the refactoring, we mainly have to add new functions to handle the
the new meta data formats and the RX hash information in the new
types.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231201223924.26955-11-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Refactor RSS capability fields

Add a new rss_cap field in the per device struct bnxt and move all
the RSS capability fields there. It will be easier to add new RSS
capabilities for the new P7 chips.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231201223924.26955-7-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Define basic P7 macros

Repurpose the BNXT_FLAG_CHIP_SR2 flag by renaming it to
BNXT_FLAG_CHIP_P7 since the SR2 chip never went to production. The SR2
statictics structure is also renamed for the P7 chip. Define the basic
P7 doorbell bits (Epoch. Toggle, etc) and implement the Epoch bit
logic. The next higher bit beyond the legal doorbell mask is the
Epoch bit used for doorbells on P7 chips. This bit is used by the
chip to detect dropped doorbells.

The 57608 chip ID belonging to the P7 family is also defined. Note
that the PCI ID is not added until the last patch in the series.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231201223924.26955-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Rename some macros for the P5 chips

In preparation to support a new P7 chip which has a lot of similarities
with the P5 chip, rename the BNXT_FLAG_CHIP_P5 flag to
BNXT_FLAG_CHIP_P5_PLUS. This will make it clear that the flag is for
P5 and newer chips.

Also, since there are no additional P5 variants in production, rename
BNXT_FLAG_CHIP_P5_THOR() to BNXT_FLAG_CHIP_P5() to keep the naming
more simple.

Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Randy Schacher <stuart.schacher@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231120234405.194542-14-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Use existing MSIX vectors for all mqprio TX rings

We can now fully support sharing the same MSIX for all mqprio TX rings
belonging to the same ethtool channel with the new infrastructure:

1. Allocate the proper entries for cp_ring_arr in struct bnxt_cp_ring_info
to support the additional TX rings.

2. Populate the tx_ring array in struct bnxt_napi for all TX rings
sharing the same NAPI.

3. bnxt_num_tx_to_cp() returns the proper NQ/completion rings to support
the TX rings in the input.

4. Adjust bnxt_get_num_ring_stats() for the reduced number of ring
counters with the new scheme.

Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add helper to get the number of CP rings required for TX rings

Up until now, each TX ring always requires a completion ring/NQ/MSIX.
bnxt_trim_rings() and the assignment of bp->cp_nr_rings always make
this assumption. This will no longer be true in the next patches, so
we refactor and add helper functions to determine the proper relationship
between TX rings and the required completion ring/NQ/MSIX. This patch
does not change the 1:1 relationship yet.

Note that on P5 chips, each RX and TX ring still requires a completion
ring. Only the number of NQs has been reduced. We should no longer call
bnxt_trim_rings() to adjust the RX and TX rings on P5 chips. Replace with
simple logic to check that RX + TX < CP and adjust accordingly.

bnxt_check_rings() should call _bnxt_get_max_rings() to get the raw
number of rings instead of bnxt_get_max_rings(). If we are about to
create TCs, bnxt_get_max_rings() would not be able to calculate the max
rings correctly.

Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add completion ring pointer in TX and RX ring structures

From the TX or RX ring structure, we need to find the corresponding
completion ring during initialization. On P5 chips, we use the MSIX/napi
entry to locate the completion ring because there is only one RX/TX
ring per MSIX. To allow multiple TX rings for each MSIX, we need
to add a direct pointer from the TX ring and RX ring structures.
This also simplifies the existing logic.

Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Restructure cp_ring_arr in struct bnxt_cp_ring_info

The cp_ring_arr is currently a fixed array of 2 pointers for the
TX and RX completion rings. These pointers are allocated during
ring initialization. Currntly, we support up to 2 completion rings
for each MSIX. In order to support more completion rings, we change
this fixed array to a pointer and allocate the required entries
during ring initialization. This patch keeps the current scheme of
allocating only 2 entries when needed. Later patches will expand
and allocate more entries when required.

Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix wrong return value check in bnxt_close_nic()

The wait_event_interruptible_timeout() function returns 0
if the timeout elapsed, -ERESTARTSYS if it was interrupted
by a signal, and the remaining jiffies otherwise if the
condition evaluated to true before the timeout elapsed.

Driver should have checked for zero return value instead of
a positive value.

MChan: Print a warning for -ERESTARTSYS. The close operation
will proceed anyway when wait_event_interruptible_timeout()
returns for any reason. Since we do the close no matter what,
we should not return this error code to the caller. Change
bnxt_close_nic() to a void function and remove all error
handling from some of the callers.

Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231208001658.14230-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Fix 2 stray ethtool -S counters

The recent firmware interface change has added 2 counters in struct
rx_port_stats_ext. This caused 2 stray ethtool counters to be
displayed.

Since new counters are added from time to time, fix it so that the
ethtool logic will only display up to the maximum known counters.
These 2 counters are not used by production firmware yet.

Fixes: 754fbf604ff6 ("bnxt_en: Update firmware interface to 1.10.2.171")
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231026013231.53271-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: extend media types to supported and autoneg modes

The current driver code does not accurately report the supported and
advertised link modes. It basically always assumes the media type
is copper for any particular speed. Utilize the recently added link
mode mappings to accurately report fully qualified ethtool link modes for
advertised and supported speeds.

If the media type is known, we will report the supported link modes for
that media only. If the media is not known, we will report all possible
supported link modes. The user can now specify any supported link modes
(including NRZ and PAM4) to advertise for autoneg. It used to only accept
copper NRZ modes.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: convert to linkmode_set_bit() API

Barring the BNXT_FW_TO_ETHTOOL speed macros, which will be removed
in the next patch, update code to use the newer API.

No functional change.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: refactor speed independent ethtool modes

A future patch in this series will change the algorithm used to
determine ethtool speed and media modes. Extract the handling of
the unrelated pause, autoneg modes into an independent function.
Also separate FEC handling out of bnxt_fw_to_ethtool_*_spds().

No functional change.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: support lane configuration via ethtool

Recent kernels support changing the number of link lanes via ethtool.
This is useful for determining the appropriate signal mode to use when
a given link speed can be achieved using different lane configurations.

Accept the ethtool lanes parameter when configuring forced speed. If
there is no lanes parameter, select a default.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: add infrastructure to lookup ethtool link mode

Add infrastructure to look up the enum ethtool_link_mode_bit_indices
from link information provided by the firmware. The link speed,
signal mode, and media type returned by firmware will be used to
look up the ethtool link mode.

The immediate benefit is that once the link mode is determined, we can
now use ethtool_params_from_link_mode() to fill the basic ethtool
parameters including the number of lanes. Lanes will be fully
supported in the next patch.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add tx_resets ring counter

Add a new tx_resets ring counter. This counter will be saved as
tx_total_resets across any reset. Since we currently do a full reset
in bnxt_sched_reset_txr(), the per ring counter will always be cleared
during reset. Only the tx_total_resets count will be meaningful and we
only display this under ethtool -S.

Link: https://lore.kernel.org/netdev/CACKFLimD-bKmJ1tGZOLYRjWzEwxkri-Mw7iFme1x2Dr0twdCeg@mail.gmail.com/
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230817231911.165035-7-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Display the ring error counters under ethtool -S

The existing driver displays the sum of 4 ring counters under ethtool -S.
These counters are in the array bnxt_sw_func_stats. These counters are
summed at the time of ethtool -S and will be lost when the device is reset.

Replace these counters with the new total ring error counters added in the
last patch. These new counters are saved before reset. ethtool -S will
now display the sum of the saved counters plus the current counters.

Link: https://lore.kernel.org/netdev/CACKFLimD-bKmJ1tGZOLYRjWzEwxkri-Mw7iFme1x2Dr0twdCeg@mail.gmail.com/
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230817231911.165035-6-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Don't issue AP reset during ethtool's reset operation

Only older NIC controller's firmware uses the PROC AP reset type.
Firmware on 5731X/5741X and newer chips does not support this reset
type. When bnxt_reset() issues a series of resets, this PROC AP
reset may actually fail on these newer chips because the firmware
is not ready to accept this unsupported command yet. Avoid this
unnecessary error by skipping this reset type on chips that don't
support it.

Fixes: 7a13240e3718 ("bnxt_en: fix ethtool_reset_flags ABI violations")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt: avoid overflow in bnxt_get_nvram_directory()

The value of an arithmetic expression is subject
of possible overflow due to a failure to cast operands to a larger data
type before performing arithmetic. Used macro for multiplication instead
operator for avoiding overflow.

Found by Security Code and Linux Verification
Center (linuxtesting.org) with SVACE.

Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230309174347.3515-1-korotkov.maxim.s@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Add missing 200G link speed reporting

bnxt_fw_to_ethtool_speed() is missing the case statement for 200G
link speed reported by firmware. As a result, ethtool will report
unknown speed when the firmware reports 200G link speed.

Fixes: 532262ba3b84 ("bnxt_en: ethtool: support PAM4 link speeds up to 200G")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Fix reporting of test result in ethtool selftest

When the selftest command fails, driver is not reporting the failure
by updating the "test->flags" when bnxt_close_nic() fails.

Fixes: eb51365846bc ("bnxt_en: Add basic ethtool -t selftest support.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt: Do not read past the end of test names

Test names were being concatenated based on a offset beyond the end of
the first name, which tripped the buffer overflow detection logic:

detected buffer overflow in strnlen
[...]
Call Trace:
bnxt_ethtool_init.cold+0x18/0x18

Refactor struct hwrm_selftest_qlist_output to use an actual array,
and adjust the concatenation to use snprintf() rather than a series of
strncat() calls.

Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Link: https://lore.kernel.org/lkml/Y8F%2F1w1AZTvLglFX@x1-carbon/
Tested-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Fixes: eb51365846bc ("bnxt_en: Add basic ethtool -t selftest support.")
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: report FEC block stats via standard interface

I must have missed that these stats are only exposed
via the unstructured ethtool -S when they got merged.
Plumb in the structured form.

Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20221130013108.90062-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: update RSS config using difference algorithm

Hardware is unable to realize all legal firmware interface state values
for hash_type. For example, if 4-tuple TCP_IPV4 hash is enabled,
4-tuple UDP_IPV4 hash must also be enabled. By providing the bits the
user intended to change instead of the possible illegal intermediate
states, the firmware is able to make better compromises when deciding
which bits to ignore.

With this new mechansim, we can now report the actual configured hash
back to the user. Add bnxt_hwrm_update_rss_hash_cfg() to report the
actual hash after user configuration.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

ethtool: linkstate: add a statistic for PHY down events

The previous attempt to augment carrier_down (see Link)
was not met with much enthusiasm so let's do the simple
thing of exposing what some devices already maintain.
Add a common ethtool statistic for link going down.
Currently users have to maintain per-driver mapping
to extract the right stat from the vendor-specific ethtool -S
stats. carrier_down does not fit the bill because it counts
a lot of software related false positives.

Add the statistic to the extended link state API to steer
vendors towards implementing all of it.

Implement for bnxt and all Linux-controlled PHYs. mlx5 and (possibly)
enic also have a counter for this but I leave the implementation
to their maintainers.

Link: https://lore.kernel.org/r/20220520004500.2250674-1-kuba@kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221104190125.684910-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: check and resize NVRAM UPDATE entry before flashing

Resize of the UPDATE entry is required if the image to
be flashed is larger than the available space. Add this step,
otherwise flashing larger firmware images by ethtool or devlink
may fail.

Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: add .get_module_eeprom_by_page() support

Add support for .get_module_eeprom_by_page() callback which
implements generic solution for module`s eeprom access.

v3: Add bnxt_get_module_status() to get a more specific extack error
string.
Return -EINVAL from bnxt_get_module_eeprom_by_page() when we
don't want to fallback to old method.
v2: Simplification suggested by Ido Schimmel

Link: https://lore.kernel.org/netdev/YzVJ%2FvKJugoz15yV@shredder/
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Fix possible crash in bnxt_hwrm_set_coal()

During the error recovery sequence, the rtnl_lock is not held for the
entire duration and some datastructures may be freed during the sequence.
Check for the BNXT_STATE_OPEN flag instead of netif_running() to ensure
that the device is fully operational before proceeding to reconfigure
the coalescing settings.

This will fix a possible crash like this:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 10 PID: 181276 Comm: ethtool Kdump: loaded Tainted: G IOE --------- - - 4.18.0-348.el8.x86_64 #1
Hardware name: Dell Inc. PowerEdge R740/0F9N89, BIOS 2.3.10 08/15/2019
RIP: 0010:bnxt_hwrm_set_coal+0x1fb/0x2a0 [bnxt_en]
Code: c2 66 83 4e 22 08 66 89 46 1c e8 10 cb 00 00 41 83 c6 01 44 39 b3 68 01 00 00 0f 8e a3 00 00 00 48 8b 93 c8 00 00 00 49 63 c6 <48> 8b 2c c2 48 8b 85 b8 02 00 00 48 85 c0 74 2e 48 8b 74 24 08 f6
RSP: 0018:ffffb11c8dcaba50 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8d168a8b0ac0 RCX: 00000000000000c5
RDX: 0000000000000000 RSI: ffff8d162f72c000 RDI: ffff8d168a8b0b28
RBP: 0000000000000000 R08: b6e1f68a12e9a7eb R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000037 R12: ffff8d168a8b109c
R13: ffff8d168a8b10aa R14: 0000000000000000 R15: ffffffffc01ac4e0
FS: 00007f3852e4c740(0000) GS:ffff8d24c0080000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000041b3ee003 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
ethnl_set_coalesce+0x3ce/0x4c0
genl_family_rcv_msg_doit.isra.15+0x10f/0x150
genl_family_rcv_msg+0xb3/0x160
? coalesce_fill_reply+0x480/0x480
genl_rcv_msg+0x47/0x90
? genl_family_rcv_msg+0x160/0x160
netlink_rcv_skb+0x4c/0x120
genl_rcv+0x24/0x40
netlink_unicast+0x196/0x230
netlink_sendmsg+0x204/0x3d0
sock_sendmsg+0x4c/0x50
__sys_sendto+0xee/0x160
? syscall_trace_enter+0x1d3/0x2c0
? __audit_syscall_exit+0x249/0x2a0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7f38524163bb

Fixes: 2151fe0830fd ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: move from strlcpy with unused retval to strscpy

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: implement callbacks for devlink selftests

Add callbacks
=============
.selftest_check: returns true for flash selftest.
.selftest_run: runs a flash selftest.

Also, refactor NVM APIs so that they can be
used with devlink and ethtool both.

Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: parse and report result field when NVRAM package install fails

Instead of always returning -ENOPKG, decode the firmware error
code further when the HWRM_NVM_INSTALL_UPDATE firmware call fails.
Return a more suitable error code to userspace and log an error
in dmesg.

This is version 2 of the earlier patch that was reverted:

02acd399533e ("bnxt_en: parse result field when NVRAM package install fails")

In this new version, if the call is made through devlink instead of
ethtool, we'll also set the error message in extack.

Link: https://lore.kernel.org/netdev/20220307141358.4d52462e@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Enable packet timestamping for all RX packets

Add driver support to enable timestamping on all RX packets
that are received by the NIC. This capability can be requested
by the applications using SIOCSHWTSTAMP ioctl with filter type
HWTSTAMP_FILTER_ALL.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: support transmit and free of aggregation buffers

This patch adds the following features:
- Support for XDP_TX and XDP_DROP action when using xdp_buff
with frags
- Support for freeing all frags attached to an xdp_buff
- Cleanup of TX ring buffers after transmits complete
- Slight change in definition of bnxt_sw_tx_bd since nr_frags
and RX producer may both need to be used
- Clear out skb_shared_info at the end of the buffer

v2: Fix uninitialized variable warning in bnxt_xdp_buff_frags_free().

Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: revert hastily merged uAPI aberrations

This reverts:
commit 02acd399533e ("bnxt_en: parse result field when NVRAM package install fails")
commit 22f5dba5065d ("bnxt_en: add an nvm test for hw diagnose")
commit bafed3f231f7 ("bnxt_en: implement hw health reporter")

These patches are still under discussion / I don't think they
are right, and since the authors don't reply promptly let me
lessen my load of "things I need to resolve before next release"
and revert them.

Acked-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220308173659.304915-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: add an nvm test for hw diagnose

Add an NVM test function for devlink hw reporter.
In this function an NVM VPD area is read followed by
a write. Test result is cached and if it is successful then
the next test can be conducted only after HW_RETEST_MIN_TIME to
avoid frequent writes to the NVM.

Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Eliminate unintended link toggle during FW reset

If the flow control settings have been changed, a subsequent FW reset
may cause the ethernet link to toggle unnecessarily. This link toggle
will increase the down time by a few seconds.

The problem is caused by bnxt_update_phy_setting() detecting a false
mismatch in the flow control settings between the stored software
settings and the current FW settings after the FW reset. This mismatch
is caused by the AUTONEG bit added to link_info->req_flow_ctrl in an
inconsistent way in bnxt_set_pauseparam() in autoneg mode. The AUTONEG
bit should not be added to link_info->req_flow_ctrl.

Reviewed-by: Colin Winegarden <colin.winegarden@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Properly report no pause support on some cards

Some cards are configured to never support link pause or PFC. Discover
these cards and properly report no pause support to ethtool. Disable
PFC settings from DCBNL if PFC is unsupported.

Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: introduce initial link state of unknown

This will force link state to always be logged for initial NIC open.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: parse result field when NVRAM package install fails

Instead of always returning -ENOPKG, decode the firmware error
code further when the HWRM_NVM_INSTALL_UPDATE firmware call fails.
Return a more suitable error code to userspace and log an error
in dmesg.

Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: add more error checks to HWRM_NVM_INSTALL_UPDATE

FW returns error code "NVM_INSTALL_UPDATE_CMD_ERR_CODE_ANTI_ROLLBACK"
in the response to indicate that HWRM_NVM_INSTALL_UPDATE command has
failed due to Anti-rollback feature. Parse the error and return an
appropriate error code to the user.

Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: refactor error handling of HWRM_NVM_INSTALL_UPDATE

This is in anticipation of handling more "cmd_err" from FW in the next
patch.

Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: report header-data split state

Aggregation rings imply header-data split.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix occasional ethtool -t loopback test failures

In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test. This
scheme fails sometime if the port is shared with management firmware
that can also send packets. The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.

Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address. This should
filter out other packets sent by management firmware.

Fixes: 91725d89b97a ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix offline ethtool selftest with RDMA enabled

For offline (destructive) self tests, we need to stop the RDMA driver
first. Otherwise, the RDMA driver will run into unrecoverable errors
when destructive firmware tests are being performed.

The irq_re_init parameter used in the half close and half open
sequence when preparing the NIC for offline tests should be set to
true because the RDMA driver will free all IRQs before the offline
tests begin.

Fixes: 55fd0cf320c3 ("bnxt_en: Add external loopback test to ethtool selftest.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Ben Li <ben.li@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix active FEC reporting to ethtool

ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None. Fix it to properly return
ETHTOOL_FEC_OFF in that case.

Fixes: 8b2775890ad8 ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: use firmware provided max timeout for messages

Some older devices cannot accommodate the 40 seconds timeout
cap for long running commands (such as NVRAM commands) due to
hardware limitations. Allow these devices to request more time for
these long running commands, but print a warning, since the longer
timeout may cause the hung task watchdog to trigger. In the case of a
firmware update operation, this is preferable to failing outright.

v2: Use bp->hwrm_cmd_max_timeout directly without the constants.

Fixes: 881d8353b05e ("bnxt_en: Add an upper bound for all firmware command timeouts.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Support CQE coalescing mode in ethtool

Support showing and setting the CQE mode in ethtool.

Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: extend ringparam setting/getting API with rx_buf_len

Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.

Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Provide stored devlink "fw" version on older firmware

On older firmware that doesn't support the HWRM_NVM_GET_DEV_INFO
command that returns detailed stored firmware versions, fallback
to use the same firmware package version that is reported to ethtool.
Refactor bnxt_get_pkgver() in bnxt_ethtool.c so that devlink can call
and get the package version.

Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Update firmware interface to 1.10.2.63

The main changes are firmware live patch support and 2 additional FEC
standard counters.

Add the matching FEC counters to ethtool counter array. Firmware older
than 220 does not return the proper size of the extended RX counters so
we need to cap it at the smaller legacy size. Otherwise the new FEC
counters may show up with garbage values.

Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: move coredump functions into dedicated file

Change bnxt_get_coredump() and bnxt_get_coredump_length() to non-static
functions.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Refactor coredump functions

The coredump functionality will be used by devlink health. Refactor
these functions that get coredump and coredump length. There is no
functional change, but the following checkpatch warnings were
addressed:

- strscpy is preferred over strlcpy.
- sscanf results should be checked, with an additional warning.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: add enable_remote_dev_reset devlink parameter

The reported parameter value should not take into account the state
of remote drivers. Firmware will reject remote resets as appropriate,
thus it is not strictly necessary to check HOT_RESET_ALLOWED before
attempting to initiate a reset. But we add the check so that we can
provide more intuitive messages when reset is not permitted.

This firmware setting needs to be restored from all functions after
a firmware reset.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: implement devlink dev reload fw_activate

Similar to reload driver_reinit, the RTNL lock is held across reload
down and up to prevent interleaving state changes. But we need to
subsequently release the RTNL lock while waiting for firmware reset
to complete.

Also keep a statistic on fw_activate resets initiated remotely from
other functions.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: use netif_is_rxfh_configured instead of open code

The open code which is dev->priv_flags & IFF_RXFH_CONFIGURED is defined as
a helper function on netdevice.h. So use netif_is_rxfh_configured()
function instead of open code. This patch doesn't change logic.

Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix TX timeout when TX ring size is set to the smallest

The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS
+ 1. Because the first TX BD for a packet is always a long TX BD, we
need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with
this value to make this more clear. The current code uses a minimum
that is off by 1. Fix it using this constant.

The tx_wake_thresh to determine when to wake up the TX queue is half the
ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next
packet which may have maximum fragments. So the comparison of the
available TX BDs with tx_wake_thresh should be >= instead of > in the
current code. Otherwise, at the smallest ring size, we will never wake
up the TX queue and will cause TX timeout.

Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: update all firmware calls to use the new APIs

The conversion follows this general pattern for most of the calls:

1. The input message is changed from a stack variable initialized
using bnxt_hwrm_cmd_hdr_init() to a pointer allocated and intialized
using hwrm_req_init().

2. If we don't need to read the firmware response, the hwrm_send_message()
call is replaced with hwrm_req_send().

3. If we need to read the firmware response, the mutex lock is replaced
by hwrm_req_hold() to hold the response. When the response is read, the
mutex unlock is replaced by hwrm_req_drop().

If additional DMA buffers are needed for firmware response data, the
hwrm_req_dma_slice() is used instead of calling dma_alloc_coherent().

Some minor refactoring is also done while doing these conversions.

v2: Fix unintialized variable warnings in __bnxt_hwrm_get_tx_rings()
and bnxt_approve_mac()

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: move HWRM API implementation into separate file

Move all firmware messaging functions and definitions to new
bnxt_hwrm.[ch]. The follow-on patches will make major modifications
to these APIs.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: count packets discarded because of netpoll

bnxt may discard packets if Rx completions are consumed
in an attempt to let netpoll make progress. It should be
extremely rare in practice but nonetheless such events
should be counted.

Since completion ring memory is allocated dynamically use
a similar scheme to what is done for HW stats to save them.

Report the stats in rx_dropped and per-netdev ethtool
counter. Chances that users care which ring dropped are
very low.

v3: only save the stat to rx_dropped on reset,
rx_total_netpoll_discards will now only show drops since
last reset, similar to other "total_discard" counters.

Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ethtool: extend coalesce setting uAPI with CQE mode

In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: broadcom: switch from 'pci_' to 'dma_' API

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below.

It has been compile tested.

@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL

@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE

@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE

@@
@@
- PCI_DMA_NONE
+ DMA_NONE

@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Increase maximum RX ring size if jumbo ring is not used

The current maximum RX ring size is defined assuming the RX jumbo ring
(aka aggregation ring) is used. The RX jumbo ring is automicatically used
when the MTU exceeds a threshold or when rx-gro-hw/lro is enabled. The RX
jumbo ring is automatically sized up to 4 times the size of the RX ring
size.

The BNXT_MAX_RX_DESC_CNT constant is the upper limit on the size of the
RX ring whether or not the RX jumbo ring is used. Obviously, the
maximum amount of RX buffer space is significantly less when the RX jumbo
ring is not used.

To increase flexibility for the user who does not use the RX jumbo ring,
we now define a bigger maximum RX ring size when the RX jumbo ring is not
used. The maximum RX ring size is now up to 8K when the RX jumbo ring
is not used. The maximum completion ring size also needs to be scaled
up to accomodate the larger maximum RX ring size.

Note that when the RX jumbo ring is re-enabled, the RX ring size will
automatically drop if it exceeds the maximum.

Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add PTP clock APIs, ioctls, and ethtool methods

Add the clock APIs to set/get/adjust the hw clock, and the related
ioctls and ethtool methods.

v2: Propagate error code from ptp_clock_register().
Add spinlock to serialize access to the timecounter. The
timecounter is accessed in process context and the RX datapath.
Read the PHC using direct registers.

Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add a new phy_flags field to the main driver structure.

Copy the phy related feature flags from the firmware call
HWRM_PORT_PHY_QCAPS to this new field. We can also remove the flags
field in the bnxt_test_info structure. It's cleaner to have all PHY
related flags in one location, directly copied from the firmware.

To keep the BNXT_PHY_CFG_ABLE() macro logic the same, we need to make
a slight adjustment to check that it is a PF.

Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: add more ethtool standard stats

Michael suggest a few more stats we can expose.

$ ethtool -S eth0 --groups eth-mac
Standard stats for eth0:
eth-mac-FramesTransmittedOK: 902623288966
eth-mac-FramesReceivedOK: 28727667047
eth-mac-FrameCheckSequenceErrors: 1
eth-mac-AlignmentErrors: 0
eth-mac-OutOfRangeLengthField: 0
$ ethtool -S eth0 | grep '\(fcs\|align\|oor\)'
rx_fcs_err_frames: 1
rx_align_err_frames: 0
tx_fcs_err_frames: 0

Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: implement ethtool standard stats

Most of the names seem to strongly correlate with names from
the standard and RFC. Whether ..+good_frames are indeed Frames..OK
I'm the least sure of.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: implement ethtool::get_fec_stats

Report corrected bits.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Clear DEFRAG flag in firmware message when retry flashing.

When the FW tells the driver to retry the INSTALL_UPDATE command after
it has cleared the NVM area, the driver is not clearing the previously
used ALLOWED_TO_DEFRAG flag. As a result the FW tries to defrag the NVM
area a second time in a loop and can fail the request.

Fixes: 1432c3f6a6ca ("bnxt_en: Retry installing FW package under NO_SPACE error condition.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Enable batch mode when using HWRM_NVM_MODIFY to flash packages.

The current scheme allocates a DMA buffer as big as the requested
firmware package file and DMAs the contents to firmware in one
operation. The buffer size can be several hundred kilo bytes and
the driver may not be able to allocate the memory. This will cause
firmware upgrade to fail.

Improve the scheme by using smaller DMA blocks and calling firmware to
DMA each block in a batch mode. Older firmware can cause excessive
NVRAM erases if the block size is too small so we try to allocate a
256K buffer to begin with and size it down successively if we cannot
allocate the memory.

Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Retry installing FW package under NO_SPACE error condition.

In bnxt_flash_package_from_fw_obj(), if firmware returns the NO_SPACE
error, call __bnxt_flash_nvram() to create the UPDATE directory and
then loop back and retry one more time.

Since the first try may fail, we use the silent version to send the
firmware commands.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Restructure bnxt_flash_package_from_fw_obj() to execute in a loop.

On NICs with a smaller NVRAM, FW installation may fail after multiple
updates due to fragmentation. The driver can retry when FW returns
a special error code. To faciliate the retry, we restructure the
logic that performs the flashing in a loop. The actual retry logic
will be added in the next patch.

Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Rearrange the logic in bnxt_flash_package_from_fw_obj().

This function will be modified in the next patch to retry flashing
the firmware in a loop. To facilate that, we rearrange the code so
that the steps that only need to be done once before the loop will be
moved to the top of the function.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Refactor bnxt_flash_nvram.

Refactor bnxt_flash_nvram() into __bnxt_flash_nvram() that takes an
additional dir_item_len parameter. The new function will be used
in subsequent patches with the dir_item_len parameter set to create
the UPDATE directory during flashing.

Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

devlink: move request_firmware out of driver

All drivers which implement the devlink flash update support, with the
exception of netdevsim, use either request_firmware or
request_firmware_direct to locate the firmware file. Rather than having
each driver do this separately as part of its .flash_update
implementation, perform the request_firmware within net/core/devlink.c

Replace the file_name parameter in the struct devlink_flash_update_params
with a pointer to the fw object.

Use request_firmware rather than request_firmware_direct. Although most
Linux distributions today do not have the fallback mechanism
implemented, only about half the drivers used the _direct request, as
compared to the generic request_firmware. In the event that
a distribution does support the fallback mechanism, the devlink flash
update ought to be able to use it to provide the firmware contents. For
distributions which do not support the fallback userspace mechanism,
there should be essentially no difference between request_firmware and
request_firmware_direct.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Avoid unnecessary NVM_GET_DEV_INFO cmd error log on VFs.

VFs do not have access permissions to issue NVM_GET_DEV_INFO
firmware command.

Fixes: 4933f6753b50 ("bnxt_en: Add bnxt_hwrm_nvm_get_dev_info() to query NVM info.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: read EEPROM A2h address using page 0

The module eeprom address range returned by bnxt_get_module_eeprom()
should be 256 bytes of A0h address space, the lower half of the A2h
address space, and page 0 for the upper half of the A2h address space.

Fix the firmware call by passing page_number 0 for the A2h slave address
space.

Fixes: 42ee18fe4ca2 ("bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Add bnxt_hwrm_nvm_get_dev_info() to query NVM info.

Add a new bnxt_hwrm_nvm_get_dev_info() to query firmware version
information via NVM_GET_DEV_INFO firmware command. Use it to
get the running version of the NVM configuration information.

This new function will also be used in subsequent patches to get the
stored firmware versions.

Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-8-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Enable online self tests for multi-host/NPAR mode.

Online self tests are not disruptive and can be run in NPAR mode
and in multi-host NIC as well.

Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-3-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bnxt_en: Add a software counter for RX ring reset.

Add a per ring rx_resets counter to count these RX resets.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Improve preset max value for ethtool -l.

The current logic that calculates the preset maximum value for combined
channel does not take into account the rings used for XDP and mqprio
TCs. Each of these features will reduce the number of TX rings. Add
the logic to divide the TX rings accordingly based on whether the
device is currently in XDP mode and whether TCs are in use.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Implement ethtool set_fec_param() method.

This feature allows the user to set the different FEC modes on the NIC
port. Any new setting will take effect immediately after a link toggle.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Report FEC settings to ethtool.

Implement .get_fecparam() method to report the configured and active FEC
settings. Also report the supported and advertised FEC settings to
the .get_link_ksettings() method.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: avoid link reset if speed is not changed

PORT_PHY_CONFIG is always sent with REQ_FLAGS_RESET_PHY set. This flag
must be set in order for the firmware to institute the requested PHY
change immediately, but it results in a link flap. This is unnecessary
and results in an improved user experience if the PHY reconfiguration
is avoided when the user requested speed does not constitute a change.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: ethtool: support PAM4 link speeds up to 200G

Add ethtool PAM4 link modes for:
50000baseCR_Full
100000baseCR2_Full
200000baseCR4_Full

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: refactor bnxt_get_fw_speed()

It will be necessary to update more than one field in the link_info
structure when PAM4 speeds are added in a later patch. Instead of
merely translating ethtool speed values to firmware speed values,
change the responsiblity of this function to update all the necessary
link_info fields required to force the speed change to the desired
ethtool value. This also reduces code duplication somewhat at the two
call sites, which otherwise both have to independently update link_info
fields to turn off auto negotiation advertisements.

Also use the appropriate REQ_FORCE_LINK_SPEED definitions. These happen
to have the same values, but req_link_speed is utilimately passed as
force_link_speed in HWRM_PORT_PHY_CFG which is not defined in terms of
REQ_AUTO_LINK_SPEED.

Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Update firmware interface spec to 1.10.1.65.

The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG
response size reduction, and a new counter added to
ctx_hw_stats_ext struct to support the new 58818 chip.

The ctx_hw_stats_ext structure is now the superset supporting the new
58818 chips and the prior P5 chips. Add a new flag to identify the new
chip and use constants for the chip specific ring statistics sizes
instead of the size of the structure.

Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back
to 96 bytes, the workaround added earlier to limit the size of this
message for forwarding to the VF can be removed.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Return -EOPNOTSUPP for ETHTOOL_GREGS on VFs.

Debug firmware commands are not supported on VFs to read registers.
This patch avoids logging unnecessary access_denied error on VFs
when user calls ETHTOOL_GREGS.

By returning error in get_regs_len() method on the VF, the get_regs()
method will not be called.

Fixes: b5d600b027eb ("bnxt_en: Add support for 'ethtool -d'")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Protect bnxt_set_eee() and bnxt_set_pauseparam() with mutex.

All changes related to bp->link_info require the protection of the
link_lock mutex. It's not sufficient to rely just on RTNL.

Fixes: 163e9ef63641 ("bnxt_en: Fix race when modifying pause settings.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: add pause frame stats

These stats are already reported in ethtool -S.
Michael confirms they are equivalent to standard stats.

v2: - fix sparse warning about endian by using the macro
- use u64 for pointer type

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix ethtool -S statitics with XDP or TCs enabled.

We are returning the wrong count for ETH_SS_STATS in get_sset_count()
when XDP or TCs are enabled. In a recent commit, we got rid of
irrelevant counters when the ring is RX only or TX only, but we
did not make the proper adjustments for the count. As a result,
when we have XDP or TCs enabled, we are returning an excess count
because some of the rings are TX only. This causes ethtool -S to
display extra counters with no counter names.

Fix bnxt_get_num_ring_stats() by not assuming that all rings will
always have RX and TX counters in combined mode.

Fixes: 125592fbf467 ("bnxt_en: show only relevant ethtool stats for a TX or RX ring")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Check for zero dir entries in NVRAM.

If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.

Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Don't query FW when netif_running() is false.

In rare conditions like two stage OS installation, the
ethtool's get_channels function may be called when the
device is in D3 state, leading to uncorrectable PCI error.
Check netif_running() first before making any query to FW
which involves writing to BAR.

Fixes: db4723b3cd2d ("bnxt_en: Check max_tx_scheduler_inputs value from firmware.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

treewide: Use fallthrough pseudo-keyword

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

bnxt_en: Add support for 'ethtool -d'

Add support to dump PXP registers and PCIe statistics.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Switch over to use the 64-bit software accumulated counters.

Now we can report all the full 64-bit CPU endian software accumulated
counters instead of the hw counters, some of which may be less than
64-bit wide. Define the necessary macros to access the software
counters.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Refactor statistics code and structures.

The driver manages multiple statistics structures of different sizes.
They are all allocated, freed, and handled practically the same. Define
a new bnxt_stats_mem structure and common allocation and free functions
for all staistics memory blocks.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Update firmware interface to 1.10.1.54.

Main changes are 200G support and fixing the definitions of discard and
error counters to match the hardware definitions.

Because the HWRM_PORT_PHY_QCFG message size has now exceeded the max.
encapsulated response message size of 96 bytes from the PF to the VF,
we now need to cap this message to 96 bytes for forwarding. The forwarded
response only needs to contain the basic link status and speed information
and can be capped without adding the new information.

v2: Fix bnxt_re compile error.

Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Remove PCIe non-counters from ethtool statistics

Remove PCIe non-counters display from ethtool statistics, as
they are not simple counters but register dump. The next few
patches will add logic to detect counter roll-over and it won't
work with these PCIe non-counters.

There will be a follow up patch to get PCIe information via
ethtool register dump.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix race when modifying pause settings.

The driver was modified to not rely on rtnl lock to protect link
settings about 2 years ago. The pause setting was missed when
making that change. Fix it by acquiring link_lock mutex before
calling bnxt_hwrm_set_pause().

Fixes: e2dc9b6e38fa ("bnxt_en: Don't use rtnl lock to protect link change logic in workqueue.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Implement ethtool -X to set indirection table.

With the new infrastructure in place, we can now support the setting of
the indirection table from ethtool.

When changing channels, in a rare case that firmware cannot reserve the
rings that were promised, we will still try to keep the RSS map and only
revert to default when absolutely necessary.

v4: Revert RSS map to default during ring change only when absolutely
necessary.

v3: Add warning messages when firmware cannot reserve the requested RX
rings, and when the RSS table entries have to change to default.

v2: When changing channels, if the RSS table size changes and RSS map
is non-default, return error.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Return correct RSS indirection table entries to ethtool -x.

Now that we have the logical indirection table, we can return these
proper logical indices directly to ethtool -x instead of the physical
IDs.

Reported-by: Jakub Kicinski <kicinski@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix up bnxt_get_rxfh_indir_size().

Fix up bnxt_get_rxfh_indir_size() to return the proper current RSS
table size for P5 chips. Change it to non-static so that bnxt.c
can use it to get the table size.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix return code to "flash_device".

When NVRAM directory is not found, return the error code
properly as per firmware command failure instead of the hardcode
-ENOBUFS.

Fixes: 3a707bed13b7 ("bnxt_en: Return -EAGAIN if fw command returns BUSY")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: bnxt: Remove Comparison to bool in bnxt_ethtool.c

Fix the following coccicheck warning:

drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:1991:5-46: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:1993:10-54: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2380:5-38: WARNING:
Comparison to bool

Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: show only relevant ethtool stats for a TX or RX ring

Currently, ethtool -S shows all TX/RX ring counters whether the
channel is combined, RX, or TX. The unused counters will always be
zero. Improve it by showing only the relevant counters if the channel
is RX or TX. If the channel is combined, the counters will be shown
exactly the same as before.

[ MChan: Lots of cleanups and simplifications on Rajesh's original
code]

Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Split HW ring statistics strings into RX and TX parts.

This will allow the RX and TX ring statistics to be separated if needed.
In the next patch, we'll be able to only display RX or TX statistcis if
the channel is RX only or TX only.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Refactor the software ring counters.

We currently have 3 software ring counters, rx_l4_csum_errors,
rx_buf_errors, and missed_irqs. The 1st two are RX counters and the
last one is a common counter. Organize them into 2 structures
bnxt_rx_sw_stats and bnxt_cmn_sw_stats.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Improve kernel log messages related to ethtool reset.

Kernel log messages for failed AP reset commands should be suppressed.
These are expected to fail on devices that do not have an AP. Add
missing driver reload message after AP reset and log it in a common
way without duplication.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: fix ethtool_reset_flags ABI violations

The ethtool ABI specifies that the reset operation should only clear
the flags that were actually reset. Setting the flags to zero after
a chip reset violates this because it does not include resetting the
application processor complex. Similarly, components that are not yet
defined are also not necessarily being reset.

The fact that chip reset does not cover the AP also means that it is
inappropriate to treat these two components exclusively of one another.
The ABI provides a mechanism to report a failure to reset independent
components via the returned bitmask, so it is also wrong to fail hard
if one of a set of independent resets is not possible.

It is incorrect to rely on the passed by reference flags in bnxt_reset(),
which are being updated as components are reset. The initially requested
value should be used instead so that hard errors do not propagate if any
earlier components could have been reset successfully.

Note, AP and chip resets are global in nature. Dedicated resets are
thus not currently supported.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: refactor ethtool firmware reset types

The case statement in bnxt_firmware_reset() dangerously mixes types.
This patch separates the application processor and whole chip resets
from the rest such that the selection is performed on a pure type.

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: prepare to refactor ethtool reset types

Extract bnxt_hwrm_firmware_reset() for performing firmware reset
operations. This new helper function will be used in a subsequent
patch to separate unrelated reset types out of bnxt_firmware_reset().

Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix Priority Bytes and Packets counters in ethtool -S.

There is an indexing bug in determining these ethtool priority
counters. Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index. This index is then used
to obtain the proper CoS queue counter. Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.

Fixes: e37fed790335 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Remove unnecessary assignment of return code

As part of converting error code in firmware message to standard
code, checking for firmware return code is removed in most of the
places. Remove the assignment of return code where the function
can directly return.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: reject unsupported coalescing params

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver did not previously reject unsupported parameters.

v3: adjust commit message for new member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/broadcom: Clean broadcom code from driver versions

Use linux kernel version for ethtool and module versions.

Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: fix error handling when flashing from file

After bnxt_hwrm_do_send_message() was updated to return standard error
codes in a recent commit, a regression in bnxt_flash_package_from_file()
was introduced. The return value does not properly reflect all
possible firmware errors when calling firmware to flash the package.

Fix it by consolidating all errors in one local variable rc instead
of having 2 variables for different errors.

Fixes: d4f1420d3656 ("bnxt_en: Convert error code in firmware message response to standard code.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: add newline to netdev_*() format strings

Add missing newlines to netdev_* format strings so the lines
aren't buffered by the printk subsystem.

Nitpicked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Improve link up detection.

In bnxt_update_phy_setting(), ethtool_get_link_ksettings() and
bnxt_disable_an_for_lpbk(), we inconsistently use netif_carrier_ok()
to determine link. Instead, we should use bp->link_info.link_up
which has the true link state. The netif_carrier state may be off
during self-test and while the device is being reset and may not always
reflect the true link state.

By always using bp->link_info.link_up, the code is now more
consistent and more correct. Some unnecessary link toggles are
now prevented with this patch.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Return error if FW returns more data than dump length

If any change happened in the configuration of VF in VM while
collecting live dump, there could be a race and firmware can return
more data than allocated dump length. Fix it by keeping track of
the accumulated core dump length copied so far and abort the copy
with error code if the next chunk of core dump will exceed the
original dump length.

Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add support for flashing the device via devlink

Use the same bnxt_flash_package_from_file() function to support
devlink flash operation.

Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

bnxt_en: Allow PHY settings on multi-function or NPAR PFs if allowed by FW.

Currently, the driver does not allow PHY settings on a multi-function or
NPAR NIC whose port is shared by more than one function. Newer
firmware now allows PHY settings on some of these NICs. Check for
this new firmware setting and allow the user to set the PHY settings
accordingly.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

bnxt_en: Skip disabling autoneg before PHY loopback when appropriate.

New firmware allows PHY loopback to be set without disabling autoneg
first. Check this capability and skip disabling autoneg when
it is supported by firmware. Using this scheme, loopback will
always work even if the PHY only supports autoneg.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

bnxt_en: Extend ETHTOOL_RESET to hot reset driver.

If firmware supports hot reset, extend ETHTOOL_RESET to support
hot reset driver which does not require a driver reload after
ETHTOOL_RESET. The driver will go through the same coordinated
reset sequence as a firmware initiated fatal/non-fatal reset.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Increase firmware response timeout for coredump commands.

Use the larger HWRM_COREDUMP_TIMEOUT value for coredump related
data response from the firmware. These commands take longer than
normal commands.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Improve RX buffer error handling.

When hardware reports RX buffer errors, the latest 57500 chips do not
require reset. The packet is discarded by the hardware and the
ring will continue to operate.

Also, add an rx_buf_errors counter for this type of error. It can help
the user to identify if the aggregation ring is too small.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add support to collect crash dump via ethtool

Driver supports 2 types of core dumps.

1. Live dump - Firmware dump when system is up and running.
2. Crash dump - Dump which is collected during firmware crash
that can be retrieved after recovery.
Crash dump is currently supported only on specific 58800 chips
which can be retrieved using OP-TEE API only, as firmware cannot
access this region directly.

User needs to set the dump flag using following command before
initiating the dump collection:

$ ethtool -W|--set-dump eth0 N

Where N is "0" for live dump and "1" for crash dump

Command to collect the dump after setting the flag:

$ ethtool -w eth0 data Filename

v3: Modify set_dump to support even when CONFIG_TEE_BNXT_FW=n.
Also change log message to netdev_info().

Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Increase timeout for HWRM_DBG_COREDUMP_XX commands

Firmware coredump messages take much longer than standard messages,
so increase the timeout accordingly.

Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Prepare bnxt_init_one() to be called multiple times.

In preparation for the new firmware reset feature, some of the logic
in bnxt_init_one() and related functions will be called again after
firmware has reset. Reset some of the flags and capabilities so that
everything that can change can be re-initialized. Refactor some
functions to probe firmware versions and capabilities. Check some
buffers before allocating as they may have been allocated previously.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Convert error code in firmware message response to standard code.

The main firmware messaging function returns the firmware defined error
code and many callers have to convert to standard error code for proper
propagation to userspace. Convert bnxt_hwrm_do_send_msg() to return
standard error code so we can do away with all the special error code
handling by the many callers.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Use a common function to print the same ethtool -f error message.

The same message is printed 3 times in the code, so use a common function
to do that.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix handling FRAG_ERR when NVM_INSTALL_UPDATE cmd fails

If FW returns FRAG_ERR in response error code, driver is resending the
command only when HWRM command returns success. Fix the code to resend
NVM_INSTALL_UPDATE command with DEFRAG install flags, if FW returns
FRAG_ERR in its response error code.

Fixes: cb4d1d626145 ("bnxt_en: Retry failed NVM_INSTALL_UPDATE with defragmentation flag enabled.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Support TPA counters on 57500 chips.

Support the new expanded TPA v2 counters on 57500 B0 chips for
ethtool -S.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Refactor ethtool ring statistics logic.

The current code assumes that the per ring statistics counters are
fixed. In newer chips that support a newer version of TPA, the
TPA counters are also changed. Refactor the code by defining these
counter names in arrays so that it is easy to add a new array for
a new set of counters supported by the newer chips.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Update firmware interface spec. to 1.10.0.89.

Among the changes are new CoS discard counters and new ctx_hw_stats_ext
struct for the latest 5750X B0 chips.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Refactor __bnxt_xmit_xdp().

__bnxt_xmit_xdp() is used by XDP_TX and ethtool loopback packet transmit.
Refactor it so that it can be re-used by the XDP_REDIRECT logic.
Restructure the TX interrupt handler logic to cleanly separate XDP_TX
logic in preparation for XDP_REDIRECT.

Acked-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: rename some xdp functions

Renaming bnxt_xmit_xdp to __bnxt_xmit_xdp to get ready for XDP_REDIRECT
support and reduce confusion/namespace collision.

Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix ethtool selftest crash under error conditions.

After ethtool loopback packet tests, we re-open the nic for the next
IRQ test. If the open fails, we must not proceed with the IRQ test
or we will crash with NULL pointer dereference. Fix it by checking
the bnxt_open_nic() return code before proceeding.

Reported-by: Somasundaram Krishnasamy <somasundaram.krishnasamy@oracle.com>
Fixes: 67fea463fd87 ("bnxt_en: Add interrupt test to ethtool -t selftest.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix possible BUG() condition when calling pci_disable_msix().

When making configuration changes, the driver calls bnxt_close_nic()
and then bnxt_open_nic() for the changes to take effect. A parameter
irq_re_init is passed to the call sequence to indicate if IRQ
should be re-initialized. This irq_re_init parameter needs to
be included in the bnxt_reserve_rings() call. bnxt_reserve_rings()
can only call pci_disable_msix() if the irq_re_init parameter is
true, otherwise it may hit BUG() because some IRQs may not have been
freed yet.

Fixes: 41e8d7983752 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Read package version from firmware.

HWRM_VER_GET firmware command returns package name that is running
actively on the adapter. Use this version instead of parsing from
the package log in NVRAM.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add support for PCIe statistics

Gather periodic PCIe statistics for ethtool -S.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Update firmware interface to 1.10.0.69.

PTP API updates for 57500 chips, new RX port stats counters and other
miscellaneous updates.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix ethtool self-test loopback.

The current code has 2 problems. It assumes that the RX ring for
the loopback packet is combined with the TX ring. This is not
true if the ethtool channels are set to non-combined mode. The
second problem is that it won't work on 57500 chips without
adjusting the logic to get the proper completion ring (cpr) pointer.
Fix both issues by locating the proper cpr pointer through the RX
ring.

Fixes: e44758b78ae8 ("bnxt_en: Use bnxt_cp_ring_info struct pointer as parameter for RX path.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: query force speeds before disabling autoneg mode.

With autoneg enabled, PHY loopback test fails. To disable autoneg,
driver needs to send a valid forced speed to FW. FW is not sending
async event for invalid speeds. To fix this, query forced speeds
and send the correct speed when disabling autoneg mode.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Do not free port statistics buffer when device is down.

Port statistics which include RDMA counters are useful even when the
netdevice is down. Do not free the port statistics DMA buffers
when the netdevice is down. This is keep the snapshot of the port
statistics and counters will just continue counting when the
netdevice goes back up.

Split the bnxt_free_stats() function into 2 functions. The port
statistics buffers will only be freed when the netdevice is
removed.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Return linux standard errors in bnxt_ethtool.c

Currently firmware specific errors are returned directly in flash_device
and reset ethtool hooks. Modify it to return linux standard errors
to userspace when flashing operations fail.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add ethtool -S priority counters.

Display the CoS counters as additional priority counters by looking up
the priority to CoS queue mapping. If the TX extended port statistics
block size returned by firmware is big enough to cover the CoS counters,
then we will display the new priority counters. We call firmware to get
the up-to-date pri2cos mapping to convert the CoS counters to
priority counters.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: get rid of num_stat_ctxs variable

For bnxt_en driver, stat_ctxs created will always be same as
cp_nr_rings. Remove extra variable that duplicates the value.
Also introduce bnxt_get_avail_stat_ctxs_for_en() helper to get
available stat_ctxs and bnxt_get_ulp_stat_ctxs() helper to return
number of stat_ctxs used by RDMA.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix filling time in bnxt_fill_coredump_record()

Fix the year and month offset while storing it in
bnxt_fill_coredump_record().

Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add software "missed_irqs" counter.

To keep track of the number of times the workaround code for 57500 A0
has been triggered. This is a per NQ counter.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Use bnxt_cp_ring_info struct pointer as parameter for RX path.

In the RX code path, we current use the bnxt_napi struct pointer to
identify the associated RX/CP rings. Change it to use the struct
bnxt_cp_ring_info pointer instead since there are now up to 2
CP rings per MSIX.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Re-structure doorbells.

The 57500 series chips have a new 64-bit doorbell format. Use a new
bnxt_db_info structure to unify the new and the old 32-bit doorbells.
Add a new bnxt_set_db() function to set up the doorbell addreses and
doorbell keys ahead of time. Modify and introduce new doorbell
helpers to help abstract and unify the old and new doorbells.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add additional extended port statistics.

Latest firmware spec. has some additional rx extended port stats and new
tx extended port stats added. We now need to check the size of the
returned rx and tx extended stats and determine how many counters are
valid. New counters added include CoS byte and packet counts for rx
and tx.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: take coredump_record structure off stack

The bnxt_coredump_record structure is very long, causing a warning
about possible stack overflow on 32-bit architectures:

drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c: In function 'bnxt_get_coredump':
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2989:1: error: the frame size of 1188 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]

I could not see any reason to operate on an on-stack copy of the
structure before copying it back into the caller-provided buffer, which
also simplifies the code here.

Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: avoid string overflow for record->system_name

The utsname()->nodename string may be 64 bytes long, and it gets
copied without the trailing nul byte into the shorter record->system_name,
as gcc now warns:

In file included from include/linux/bitmap.h:9,
from include/linux/ethtool.h:16,
from drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:13:
In function 'strncpy',
inlined from 'bnxt_fill_coredump_record' at drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2863:2:
include/linux/string.h:254:9: error: '__builtin_strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]

Using strlcpy() at least avoids overflowing the destination buffer
and adds proper nul-termination. It may still truncate long names
though, which probably can't be solved here.

Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix strcpy() warnings in bnxt_ethtool.c

This patch fixes following smatch warnings:

drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2826 bnxt_fill_coredump_seg_hdr() error: strcpy() '"sEgM"' too large for 'seg_hdr->signature' (5 vs 4)
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2858 bnxt_fill_coredump_record() error: strcpy() '"cOrE"' too large for 'record->signature' (5 vs 4)
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2879 bnxt_fill_coredump_record() error: strcpy() 'utsname()->sysname' too large for 'record->os_name' (65 vs 32)

Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add BNXT_NEW_RM() macro.

The BNXT_FLAG_NEW_RM flag is checked a lot in the code to determine if
the new resource manager is in effect. Define a macro to perform
this check.

Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add support for ethtool get dump.

Add support to collect live firmware coredump via ethtool.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add external loopback test to ethtool selftest.

Add code to detect firmware support for external loopback and the extra
test entry for external loopback.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Adjust timer based on ethtool stats-block-usecs settings.

The driver gathers statistics using 2 mechanisms. Some stats are DMA'ed
directly from hardware and others are polled from the driver's timer.
Currently, we only adjust the DMA frequency based on the ethtool
stats-block-usecs setting. This patch adjusts the driver's timer
frequency as well to make everything consistent.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Update firmware interface version to 1.9.2.25.

New interface has firmware core dump support, new extended port
statistics, and IF state change notifications to the firmware.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Read phy eeprom A2h address only when optical diagnostics is supported.

For SFP+ modules, 0xA2 page is available only when Diagnostic Monitoring
Type [Address A0h, Byte 92] is implemented. Extend bnxt_get_module_info(),
to read optical diagnostics support at offset 92(0x5c) and set eeprom_len
length to ETH_MODULE_SFF_8436_LEN (to exclude A2 page), if dianostics is
not supported.

Also in bnxt_get_module_info(), module id is read from offset 0x5e which
is not correct. It was working by accident, as offset was not effective
without setting enables flag in the firmware request. SFP module id is
present at location 0. Fix this by removing the offset and read it
from location 0.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Reserve rings in bnxt_set_channels() if device is down.

The current code does not reserve rings during ethtool -L when the device
is down. The rings will be reserved when the device is later opened.

Change it to reserve rings during ethtool -L when the device is down.
This provides a better guarantee that the device open will be successful
when the rings are reserved ahead of time.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Do not allow VF to read EEPROM.

Firmware does not allow the operation and would return failure, causing
a warning in dmesg. So check for VF and disallow it in the driver.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Display function level rx/tx_discard_pkts via ethtool

Add counters to display sum of rx/tx_discard_pkts of all rings as
function level statistics via ethtool.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix memory fault in bnxt_ethtool_init()

In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver. This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.

Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096. Move the kzalloc() call
into the bnxt_get_pkgver() function.

Fixes: 3ebf6f0a09a2 ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix ethtool -x crash when device is down.

Fix ethtool .get_rxfh() crash by checking for valid indirection table
address before copying the data.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Check max_tx_scheduler_inputs value from firmware.

When checking for the maximum pre-set TX channels for ethtool -l, we
need to check the current max_tx_scheduler_inputs parameter from firmware.
This parameter specifies the max input for the internal QoS nodes currently
available to this function. The function's TX rings will be capped by this
parameter. By adding this logic, we provide a more accurate pre-set max
TX channels to the user.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add extended port statistics support

Gather periodic extended port statistics, if the device is PF and
link is up.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Include additional hardware port statistics in ethtool -S.

Include additional hardware port statistics in ethtool -S, which
are useful for debugging.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: fix clear flags in ethtool reset handling

Clear flags when reset command processed successfully for components
specified.

Fixes: 6502ad5963a5 ("bnxt_en: Add ETH_RESET_AP support")
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: add support for software dynamic interrupt moderation

This implements the changes needed for the bnxt_en driver to add support
for dynamic interrupt moderation per ring.

This does add additional counters in the receive path, but testing shows
that any additional instructions are offset by throughput gain when the
default configuration is for low latency.

Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add ETH_RESET_AP support

Add ETH_RESET_AP support handling to reset the internal
Application Processor(s) of the SmartNIC card.

Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix an error handling path in 'bnxt_get_module_eeprom()'

Error code returned by 'bnxt_read_sfp_module_eeprom_info()' is handled a
few lines above when reading the A0 portion of the EEPROM.
The same should be done when reading the A2 portion of the EEPROM.

In order to correctly propagate an error, update 'rc' in this 2nd call as
well, otherwise 0 (success) is returned.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: fix typo in bnxt_set_coalesce

Recent refactoring of coalesce settings contained a typo that prevents
receive settings from being set properly.

Fixes: 18775aa8a91f ("bnxt_en: Reorganize the coalescing parameters.")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Reorganize the coalescing parameters.

The current IRQ coalescing logic is a little messy. The ethtool
parameters are mapped to hardware parameters in a way that is difficult
to understand. The first step is to better organize the parameters
by adding the new structure bnxt_coal. The structure is used by both
the RX and TX sets of coalescing parameters.

Adjust the default coal_ticks to 14 us and 28 us for RX and TX.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add ethtool reset method

This is a firmware internal reset after driver is unloaded.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Get firmware package version one time.

The current code retrieves the firmware package version from firmware
everytime ethtool -i is run. There is no reason to do that as the
firmware will not change while the driver is loaded. Get the version
once at init time.

Also, display the full 4-part firmware version string and remove the
less useful interface spec version.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Check for zero length value in bnxt_get_nvram_item().

Return -EINVAL if the length is zero and not proceed to do essentially
nothing.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix possible corrupted NVRAM parameters from firmware response.

In bnxt_find_nvram_item(), it is copying firmware response data after
releasing the mutex. This can cause the firmware response data
to be corrupted if the next firmware response overwrites the response
buffer. The rare problem shows up when running ethtool -i repeatedly.

Fix it by calling the new variant _hwrm_send_message_silent() that requires
the caller to take the mutex and to release it after the response data has
been copied.

Fixes: 3ebf6f0a09a2 ("bnxt_en: Add installed-package version reporting via Ethtool GDRVINFO")
Reported-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Don't use rtnl lock to protect link change logic in workqueue.

As a further improvement to the PF/VF link change logic, use a private
mutex instead of the rtnl lock to protect link change logic. With the
new mutex, we don't have to take the rtnl lock in the workqueue when
we have to handle link related functions. If the VF and PF drivers
are running on the same host and both take the rtnl lock and one is
waiting for the other, it will cause timeout. This patch fixes these
timeouts.

Fixes: 90c694bb7181 ("bnxt_en: Fix RTNL lock usage on bnxt_update_link().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Improve tx ring reservation logic.

When the number of TX rings is changed (e.g. ethtool -L, enabling XDP TX
rings, etc), the current code tries to reserve the new number of TX rings
before closing and re-opening the NIC. If we are unable to reserve the
new TX rings, we abort the operation and keep the current TX rings.

The problem is that the firmware will disable the current TX rings even
when it cannot reserve the new set of TX rings. We fix it as follows:

1. Instead of reserving the new set of TX rings, just ask the firmware
to check if the new set of TX rings is available. There is a flag in
the firmware message to do that. If not available, abort and the
current TX rings will not be disabled.

2. Do the actual TX ring reservation in the path that opens the NIC.
We keep the number of TX rings currently successfully reserved. If the
number of TX rings is different than the reserved TX rings, we call
firmware and reserve again.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt: fix unsigned comparsion with 0

Fixes warning because location is u32 and can never be netative
warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Allow the user to set ethtool stats-block-usecs to 0.

For debugging purpose, it is sometimes useful to disable periodic
port statistics updates, so that the firmware logs will not be
filled with statistics update messages.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add bnxt_get_num_stats() to centrally get the number of ethtool stats.

Instead of duplicating the logic multiple times. Also, it is unnecessary
to zero the buffer in .get_ethtool_stats() because it is already zeroed
by the caller.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix bug in ethtool -L.

When changing channels from combined to rx/tx or vice versa, the code
uses the wrong "sh" parameter to determine if we are reserving rings
for shared or non-shared mode. It should be using the ethtool requested
"sh" parameter instead of the current "sh" parameter.

Fix it by passing the "sh" parameter to bnxt_reserve_rings(). For
ethtool, we will pass in the requested "sh" parameter.

Fixes: 391be5c27364 ("bnxt_en: Implement new scheme to reserve tx rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Optimize doorbell write operations for newer chips.

Older chips require the doorbells to be written twice, but newer chips
do not. Add a new common function bnxt_db_write() to write all
doorbells appropriately depending on the chip. Eliminating the extra
doorbell on newer chips has a significant performance improvement
on pktgen.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add 100G link speed reporting for BCM57454 ASIC in ethtool

Added support for 100G link speed reporting for Broadcom BCM57454
ASIC in ethtool command.

Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add interrupt test to ethtool -t selftest.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add PHY loopback to ethtool self-test.

It is necessary to disable autoneg before enabling PHY loopback,
otherwise link won't come up.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add ethtool mac loopback self test.

The mac loopback self test operates in polling mode. To support that,
we need to add functions to open and close the NIC half way. The half
open mode allows the rings to operate without IRQ and NAPI. We
use the XDP transmit function to send the loopback packet.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add basic ethtool -t selftest support.

Add the basic infrastructure and only firmware tests initially.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add ethtool set_wol method.

And add functions to set and free magic packet filter.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add ethtool get_wol method.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix ethtool -l pre-set max combined channel.

With commit d1e7925e6d80 ("bnxt_en: Centralize logic to reserve rings."),
ring allocation for combined rings has become stricter. A combined
ring must now have an rx-tx ring pair. The pre-set max. for combined
rings should now be min(rx, tx).

Fixes: d1e7925e6d80 ("bnxt_en: Centralize logic to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Retry failed NVM_INSTALL_UPDATE with defragmentation flag.

If the HWRM_NVM_INSTALL_UPDATE command fails with the error code
NVM_INSTALL_UPDATE_CMD_ERR_CODE_FRAG_ERR, retry the command with
a new flag to allow defragmentation. Since we are checking the
response for error code, we also need to take the mutex until
we finish reading the response.

Signed-off-by: Kshitij Soni <kshitij.soni@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add a set of TX rings to support XDP.

Add logic for an extra set of TX rings for XDP. If enabled, this
set of TX rings equals the number of RX rings and shares the same
IRQ as the RX ring set. A new field bp->tx_nr_rings_xdp is added
to keep track of these TX XDP rings. Adjust all other relevant functions
to handle bp->tx_nr_rings_xdp.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Centralize logic to reserve rings.

Currently, bnxt_setup_tc() and bnxt_set_channels() have similar and
duplicated code to check and reserve rx and tx rings. Add a new
function bnxt_reserve_rings() to centralize the logic. This will
make it easier to add XDP_TX support which requires allocating a
new set of TX rings.

Also, the tx ring checking logic in bnxt_setup_msix() can be removed.
The rings have been reserved before hand.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add support for ethtool -p.

Add LED blinking code to support ethtool -p on the PF.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Implement new scheme to reserve tx rings.

In order to properly support TX rate limiting in SRIOV VF functions or
NPAR functions, firmware needs better control over tx ring allocations.
The new scheme requires the driver to reserve the number of tx rings
and to query to see if the requested number of tx rings is reserved.
The driver will use the new scheme when the firmware interface spec is
1.6.1 or newer.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add IPV6 hardware RFS support.

Accept ipv6 flows in .ndo_rx_flow_steer() and support ETHTOOL_GRXCLSRULE
ipv6 flows.

Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix and clarify link_info->advertising.

The advertising field is closely related to the auto_link_speeds field.
The former is the user setting while the latter is the firmware setting.
Both should be u16. We should use the advertising field in
bnxt_get_link_ksettings because the auto_link_speeds field may not
be updated with the latest from the firmware yet.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add PFC statistics.

Report PFC statistics to ethtool -S and DCBNL.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add ethtool -n|-N rx-flow-hash support.

To display and modify the RSS hash.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Support for "ethtool -r" command

Restart autoneg if autoneg is enabled.

Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix ethtool -l|-L inconsistent channel counts.

The existing code is inconsistent in reporting and accepting the combined
channel count. bnxt_get_channels() reports maximum combined as the
maximum rx count. bnxt_set_channels() accepts combined count that
cannot be bigger than max rx or max tx.

For example, if max rx = 2 and max tx = 1, we report max supported
combined to be 2. But if the user tries to set combined to 2, it will
fail because 2 is bigger than max tx which is 1.

Fix the code to be consistent. Max allowed combined = max(max_rx, max_tx).
We will accept a combined channel count <= max(max_rx, max_tx).

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Added support for Secure Firmware Update

Using Ethtool flashdev command, entire NVM package (*.pkg) files
may now be staged into the "update" area of the NVM and subsequently
verified and installed by the firmware using the newly introduced
command: NVM_INSTALL_UPDATE.

We also introduce use of the new firmware command FW_SET_TIME so that the
NVM-resident package installation log contains valid time-stamps.

Signed-off-by: Rob Swindell <Rob.Swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Workaround Nitro A0 hardware RX bug (part 2).

The hardware is unable to drop rx packets not matching the RX filters. To
workaround it, we create a special VNIC and configure the hardware to
direct all packets not matching the filters to it. We then setup the
driver to drop packets received on this VNIC.

This patch creates the infrastructure for this VNIC, reserves a
completion ring, and rx rings. Only shared completion ring mode is
supported. The next 2 patches add a NAPI to handle packets from this
VNIC and the setup of the VNIC.

Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: initialize rc to zero to avoid returning garbage

rc is not initialized so it can contain garbage if it is not
set by the call to bnxt_read_sfp_module_eeprom_info. Ensure
garbage is not returned by initializing rc to 0.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Allow statistics DMA to be configurable using ethtool -C.

The allowable range is 0.25 seconds to 1 second interval. Default is
1 second.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add support for firmware updates for additional processors.

Add support to the Ethtool FLASHDEV command handler for additional
firmware types to cover all the on-chip processors.

Signed-off-by: Rob Swindell <rob.swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Request firmware reset after successful firwmare update

Upon successful mgmt processor firmware update, request a self
reset upon next PCIe reset (e.g. system reboot).

Signed-off-by: Rob Swindell <rob.swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add support for updating flash more securely

To support Secure Firmware Update, we must be able to allocate
a staging area in the Flash. This patch adds support for the
"update" type to tell firmware to do that.

Signed-off-by: Rob Swindell <rob.swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: VF/NPAR should return -EOPNOTSUPP for unsupported ethtool ops.

Returning 0 for doing nothing is confusing to the user.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Support new ETHTOOL_{G|S}LINKSETTINGS API.

To fully support 25G and 50G link settings.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Don't allow autoneg on cards that don't support it.

Some cards do not support autoneg. The current code does not prevent the
user from enabling autoneg with ethtool on such cards, causing confusion.
Firmware provides the autoneg capability information and we just need to
store it in the support_auto_speeds field in bnxt_link_info struct.
The ethtool set_settings() call will check this field before proceeding
with autoneg.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Enable NPAR (NIC Partitioning) Support.

NPAR type is read from bnxt_hwrm_func_qcfg. Do not allow changing link
parameters if in NPAR mode sinc ethe port is shared among multiple
partitions. The link parameters are set up by firmware.

Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO

Add support to fetch the SFP EEPROM settings from the firmware
and display it via the ethtool -m command. We support SFP+ and QSFP
modules.

v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix invalid max channel parameter in ethtool -l.

When there is only 1 MSI-X vector or in INTA mode, tx and rx pre-set
max channel parameters are shown incorrectly in ethtool -l. With only 1
vector, bnxt_get_max_rings() will return -ENOMEM. bnxt_get_channels
should check this return value, and set max_rx/max_tx to 0 if it is
non-zero.

Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Disallow forced speed for 10GBaseT devices.

10GBaseT devices must autonegotiate to determine master/slave clocking.
Disallow forced speed in ethtool .set_settings() for these devices.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Improve ethtool .get_settings().

If autoneg is off, we should always report the speed and duplex settings
even if it is link down so the user knows the current settings. The
unknown speed and duplex should only be used for autoneg when link is
down.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Check for valid forced speed during ethtool -s.

Check that the forced speed is a valid speed supported by firmware.
If not supported, return -EINVAL.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add get_eee() and set_eee() ethtool support.

Allow users to get|set EEE parameters.

v2: Added comment for preserving the tx_lpi_timer value in get_eee.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add EEE setup code.

1. Add bnxt_hwrm_set_eee() function to setup EEE firmware parameters based
on the bp->eee settings.
2. The new function bnxt_eee_config_ok() will check if EEE parameters need
to be modified due to autoneg changes.
3. bnxt_hwrm_set_link() has added a new parameter to update EEE. If the
parameter is set, it will call bnxt_hwrm_set_eee().

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add basic EEE support.

Get EEE capability and the initial EEE settings from firmware.
Add "EEE is active | not active" to link up dmesg.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Improve flow control autoneg with Firmware 1.2.1 interface.

Make use of the new AUTONEG_PAUSE bit in the new interface to better
control autoneg flow control settings, independent of RX and TX
advertisement settings.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Update to Firmware 1.2.2 spec.

Use new field names in API structs and stop using deprecated fields
auto_link_speed and auto_duplex in phy_cfg/phy_qcfg structs.

Update copyright year to 2016.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix ethtool -a reporting.

To report flow control tx/rx settings accurately regardless of autoneg
setting, we should use link_info->req_flow_ctrl. Before this patch,
the reported settings were only correct when autoneg was on.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Include hardware port statistics in ethtool -S.

Include the more useful port statistics in ethtool -S for the PF device.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Extend autoneg to all speeds.

Allow all autoneg speeds aupported by firmware to be advertised. If
the advertising parameter is 0, then all supported speeds will be
advertised.

Remove BNXT_ALL_COPPER_ETHTOOL_SPEED which is no longer used as all
supported speeds can be advertised.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Use common function to get ethtool supported flags.

The supported bits and advertising bits in ethtool have the same
definitions. The same is true for the firmware bits. So use the
common function to handle the conversion for both supported and
advertising bits.

v2: Don't use parentheses on function return.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add reporting of link partner advertisement.

And report actual pause settings to ETHTOOL_GPAUSEPARAM to let ethtool
resolve the actual pause settings.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Refactor bnxt_fw_to_ethtool_advertised_spds().

Include the conversion of pause bits and add one extra call layer so
that the same refactored function can be reused to get the link partner
advertisement bits.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add hwrm_send_message_silent().

This is used to send NVM_FIND_DIR_ENTRY messages which can return error
if the entry is not found. This is normal and the error message will
cause unnecessary alarm, so silence it.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO

For everything to fit, we remove the PHY microcode version and replace it
with the firmware package version in the fw_version string.

Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add coalescing support for tx rings.

When tx and rx rings don't share the same completion ring, tx coalescing
parameters can be set differently from the rx coalescing parameters.
Otherwise, use rx coalescing parameters on shared completion rings.

Adjust rx coalescing default values to lower interrupt rate.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Store irq coalescing timer values in micro seconds.

Don't convert these to internal hardware tick values before storing
them. This avoids the confusion of ethtool -c returning slightly
different values than the ones set using ethtool -C when we convert
hardware tick values back to micro seconds. Add better comments for
the hardware settings.

Also, rename the current set of coalescing fields with rx_ prefix.
The next patch will add support of tx coalescing values.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Remove 20G support and advertise only 40GbaseCR4.

20G is not supported by production hardware and only the 40GbaseCR4 standard
is supported.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Cleanup and Fix flow control setup logic

Cleanup bnxt_probe_phy() to cleanly separate 2 code blocks for autoneg
on and off. Autoneg flow control is possible only if autoneg is enabled.

In bnxt_get_settings(), Pause and Asym_Pause are always supported.
Only the advertisement bits change depending on the ethtool -A setting
in auto mode.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix ethtool autoneg logic.

1. Determine autoneg on|off setting from link_info->autoneg. Using the
firmware returned setting can be misleading if autoneg is changed and
there hasn't been a phy update from the firmware.

2. If autoneg is disabled, link_info->autoneg should be set to 0 to
indicate both speed and flow control autoneg are disabled.

3. To enable autoneg flow control, speed autoneg must be enabled.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Reset embedded processor after applying firmware upgrade

Use HWRM_FW_RESET command to request a self-reset of the embedded
processor(s) after successfully applying a firmware update. For boot
processor, the self-reset is currently deferred until the next PCIe reset.

Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Modify ethtool -l|-L to support combined or rx/tx rings.

The driver can support either all combined or all rx/tx rings. The
default is combined, but the user can now select rx/tx rings.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Modify bnxt_get_max_rings() to support shared or non shared rings.

Add logic to calculate how many shared or non shared rings can be
supported. Default is to use shared rings.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Check hardware resources before enabling NTUPLE.

The hardware resources required to enable NTUPLE varies depending on
how many rx channels are configured. We need to make sure we have the
resources before we enable NTUPLE. Add bnxt_rfs_capable() to do the
checking.

In addition, we need to do the same checking in ndo_fix_features(). As
the rx channels are changed using ethtool -L, we call
netdev_update_features() to make the necessary adjustment for NTUPLE.

Calling netdev_update_features() in netif_running() state but before
calling bnxt_open_nic() would be a problem. To make this work,
bnxt_set_features() has to be modified to test for BNXT_STATE_OPEN for
the true hardware state instead of checking netif_running().

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Add support for upgrading APE/NC-SI firmware via Ethtool FLASHDEV

NC-SI firmware of type apeFW (10) is now supported.

Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: New Broadcom ethernet driver.

Broadcom ethernet driver for the new family of NetXtreme-C/E
ethernet devices.

v5:
- Removed empty blank lines at end of files (noted by David Miller).
- Moved busy poll helper functions to bnxt.h to at least make the
.c file look less cluttered with #ifdef (noted by Stephen Hemminger).

v4:
- Broke up 2 long message strings with "\n" (suggested by John Linville)
- Constify an array of strings (suggested by Stephen Hemminger)
- Improve bnxt_vf_pciid() (suggested by Stephen Hemminger)
- Use PCI_VDEVICE() to populate pci_device_id table for more compact
source.

v3:
- Fixed 2 more sparse warnings.
- Removed some unused structures in .h files.

v2:
- Fixed all kbuild test robot reported warnings.
- Fixed many of the checkpatch.pl errors and warnings.
- Fixed the Kconfig description (noted by Dmitry Kravkov).

Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>