net: dsa: sja1105: complete tc-cbs offload support on SJA1110

The blamed commit left this delta behind:

struct sja1105_cbs_entry {
- u64 port;
- u64 prio;
+ u64 port; /* Not used for SJA1110 */
+ u64 prio; /* Not used for SJA1110 */
u64 credit_hi;
u64 credit_lo;
u64 send_slope;
u64 idle_slope;
};

but did not actually implement tc-cbs offload fully for the new switch.
The offload is accepted, but it doesn't work.

The difference compared to earlier switch generations is that now, the
table of CBS shapers is sparse, because there are many more shapers, so
the mapping between a {port, prio} and a table index is static, rather
than requiring us to store the port and prio into the sja1105_cbs_entry.

So, the problem is that the code programs the CBS shaper parameters at a
dynamic table index which is incorrect.

All that needs to be done for SJA1110 CBS shapers to work is to bypass
the logic which allocates shapers in a dense manner, as for SJA1105, and
use the fixed mapping instead.

Fixes: 3e77e59bf8cf ("net: dsa: sja1105: add support for the SJA1110 switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: C45 only transactions for PCS

The sja1105 MDIO bus driver only supports C45 transfers. Update the
function names to make this clear, pass the mmd as a parameter, and
register the accessors to the _c45 ops of the bus driver structure.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: update NXP copyright text

NXP Legal insists that the following are not fine:

- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"

- Putting a "(c)" sign in the copyright string

- Putting a comma in the copyright string

The only accepted copyright string format is "Copyright <year-range> NXP".

This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: tag_sja1105: stop asking the sja1105 driver in sja1105_xmit_tpid

Introduced in commit 38b5beeae7a4 ("net: dsa: sja1105: prepare tagger
for handling DSA tags and VLAN simultaneously"), the sja1105_xmit_tpid
function solved quite a different problem than our needs are now.

Then, we used best-effort VLAN filtering and we were using the xmit_tpid
to tunnel packets coming from an 8021q upper through the TX VLAN allocated
by tag_8021q to that egress port. The need for a different VLAN protocol
depending on switch revision came from the fact that this in itself was
more of a hack to trick the hardware into accepting tunneled VLANs in
the first place.

Right now, we deny 8021q uppers (see sja1105_prechangeupper). Even if we
supported them again, we would not do that using the same method of
{tunneling the VLAN on egress, retagging the VLAN on ingress} that we
had in the best-effort VLAN filtering mode. It seems rather simpler that
we just allocate a VLAN in the VLAN table that is simply not used by the
bridge at all, or by any other port.

Anyway, I have 2 gripes with the current sja1105_xmit_tpid:

1. When sending packets on behalf of a VLAN-aware bridge (with the new
TX forwarding offload framework) plus untagged (with the tag_8021q
VLAN added by the tagger) packets, we can see that on SJA1105P/Q/R/S
and later (which have a qinq_tpid of ETH_P_8021AD), some packets sent
through the DSA master have a VLAN protocol of 0x8100 and others of
0x88a8. This is strange and there is no reason for it now. If we have
a bridge and are therefore forced to send using that bridge's TPID,
we can as well blend with that bridge's VLAN protocol for all packets.

2. The sja1105_xmit_tpid introduces a dependency on the sja1105 driver,
because it looks inside dp->priv. It is desirable to keep as much
separation between taggers and switch drivers as possible. Now it
doesn't do that anymore.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: properly power down the microcontroller clock for SJA1110

It turns out that powering down the BASE_TIMER_CLK does not turn off the
microcontroller, just its timers, including the one for the watchdog.
So the embedded microcontroller is still running, and potentially still
doing things.

To prevent unwanted interference, we should power down the BASE_MCSS_CLK
as well (MCSS = microcontroller subsystem).

The trouble is that currently we turn off the BASE_TIMER_CLK for SJA1110
from the .clocking_setup() method, mostly because this is a Clock
Generation Unit (CGU) setting which was traditionally configured in that
method for SJA1105. But in SJA1105, the CGU was used for bringing up the
port clocks at the proper speeds, and in SJA1110 it's not (but rather
for initial configuration), so it's best that we rebrand the
sja1110_clocking_setup() method into what it really is - an implementation
of the .disable_microcontroller() method.

Since disabling the microcontroller only needs to be done once, at probe
time, we can choose the best place to do that as being in sja1105_setup(),
before we upload the static config to the device. This guarantees that
the static config being used by the switch afterwards is really ours.

Note that the procedure to upload a static config necessarily resets the
switch. This already did not reset the microcontroller, only the switch
core, so since the .disable_microcontroller() method is guaranteed to be
called by that point, if it's disabled, it remains disabled. Add a
comment to make that clear.

With the code movement for SJA1110 from .clocking_setup() to
.disable_microcontroller(), both methods are optional and are guarded by
"if" conditions.

Tested by enabling in the device tree the rev-mii switch port 0 that
goes towards the microcontroller, and flashing a firmware that would
have networking. Without this patch, the microcontroller can be pinged,
with this patch it cannot.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: constify the sja1105_regs structures

The struct sja1105_regs tables are not modified during the runtime of
the driver, so they can be made constant. In fact, struct sja1105_info
already holds a const pointer to these.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: plug in support for 2500base-x

The MAC treats 2500base-x same as SGMII (yay for that) except that it
must be set to a different speed.

Extend all places that check for SGMII to also check for 2500base-x.

Also add the missing 2500base-x compatibility matrix entry for SJA1110D.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: register the PCS MDIO bus for SJA1110

On the SJA1110, the PCS of each SERDES-capable port is accessed through
a different memory window which is 0x100 bytes in size, denoted by
"pcs_base".

In each PCS register access window, the XPCS MMDs are accessed in an
indirect way: in pages/banks of up to 0x100 addresses each. Changing the
page/bank is done by writing to a special register at the end of the
access window.

The MDIO register map accessed indirectly through the indirect banked
method described above is similar to what SJA1105 has: upper 5 bits are
the MMD, lower 16 bits are the MDIO address within that MMD.

Since the PHY ID reported by the XPCS inside SJA1110 is also all zeroes
(like SJA1105), we need to trap those reads and return a fake PHY ID so
that the xpcs driver can apply some specific fixups for our integration.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: migrate to xpcs for SGMII

There is a desire to use the generic driver for the Synopsys XPCS
located in drivers/net/pcs, and to achieve that, the sja1105 driver must
expose an MDIO bus for the SGMII PCS, because the XPCS probes as an
mdio_device.

In preparation of the SJA1110 which in fact has a different access
procedure for the SJA1105, we register this PCS MDIO bus once in the
common code, but we implement function pointers for the read and write
methods. In this patch there is a single implementation for them.

There is exactly one MDIO bus for the PCS, this will contain all PCSes
at MDIO addresses equal to the port number.

We delete a bunch of hardware support code because the xpcs driver
already does what we need.

We need to hack up the MDIO reads for the PHY ID, since our XPCS
instantiation returns zeroes and there are some specific fixups which
need to be applied by the xpcs driver.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: implement TX timestamping for SJA1110

The TX timestamping procedure for SJA1105 is a bit unconventional
because the transmit procedure itself is unconventional.

Control packets (and therefore PTP as well) are transmitted to a
specific port in SJA1105 using "management routes" which must be written
over SPI to the switch. These are one-shot rules that match by
destination MAC address on traffic coming from the CPU port, and select
the precise destination port for that packet. So to transmit a packet
from NET_TX softirq context, we actually need to defer to a process
context so that we can perform that SPI write before we send the packet.
The DSA master dev_queue_xmit() runs in process context, and we poll
until the switch confirms it took the TX timestamp, then we annotate the
skb clone with that TX timestamp. This is why the sja1105 driver does
not need an skb queue for TX timestamping.

But the SJA1110 is a bit (not much!) more conventional, and you can
request 2-step TX timestamping through the DSA header, as well as give
the switch a cookie (timestamp ID) which it will give back to you when
it has the timestamp. So now we do need a queue for keeping the skb
clones until their TX timestamps become available.

The interesting part is that the metadata frames from SJA1105 haven't
disappeared completely. On SJA1105 they were used as follow-ups which
contained RX timestamps, but on SJA1110 they are actually TX completion
packets, which contain a variable (up to 32) array of timestamps.
Why an array? Because:
- not only is the TX timestamp on the egress port being communicated,
but also the RX timestamp on the CPU port. Nice, but we don't care
about that, so we ignore it.
- because a packet could be multicast to multiple egress ports, each
port takes its own timestamp, and the TX completion packet contains
the individual timestamps on each port.

This is unconventional because switches typically have a timestamping
FIFO and raise an interrupt, but this one doesn't. So the tagger needs
to detect and parse meta frames, and call into the main switch driver,
which pairs the timestamps with the skbs in the TX timestamping queue
which are waiting for one.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: add the RX timestamping procedure for SJA1110

This is really easy, since the full RX timestamp is in the DSA trailer
and the tagger code transfers it to SJA1105_SKB_CB(skb)->tstamp, we just
need to move it to the skb shared info region. This is as opposed to
SJA1105, where the RX timestamp was received in a meta frame (so there
needed to be a state machine to pair the 2 packets) and the timestamp
was partial (so the packet, once matched with its timestamp, needed to
be added to an RX timestamping queue where the PTP aux worker would
reconstruct that timestamp).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: add support for the SJA1110 native tagging protocol

The SJA1110 has improved a few things compared to SJA1105:

- To send a control packet from the host port with SJA1105, one needed
to program a one-shot "management route" over SPI. This is no longer
true with SJA1110, you can actually send "in-band control extensions"
in the packets sent by DSA, these are in fact DSA tags which contain
the destination port and switch ID.

- When receiving a control packet from the switch with SJA1105, the
source port and switch ID were written in bytes 3 and 4 of the
destination MAC address of the frame (which was a very poor shot at a
DSA header). If the control packet also had an RX timestamp, that
timestamp was sent in an actual follow-up packet, so there were
reordering concerns on multi-core/multi-queue DSA masters, where the
metadata frame with the RX timestamp might get processed before the
actual packet to which that timestamp belonged (there is no way to
pair a packet to its timestamp other than the order in which they were
received). On SJA1110, this is no longer true, control packets have
the source port, switch ID and timestamp all in the DSA tags.

- Timestamps from the switch were partial: to get a 64-bit timestamp as
required by PTP stacks, one would need to take the partial 24-bit or
32-bit timestamp from the packet, then read the current PTP time very
quickly, and then patch in the high bits of the current PTP time into
the captured partial timestamp, to reconstruct what the full 64-bit
timestamp must have been. That is awful because packet processing is
done in NAPI context, but reading the current PTP time is done over
SPI and therefore needs sleepable context.

But it also aggravated a few things:

- Not only is there a DSA header in SJA1110, but there is a DSA trailer
in fact, too. So DSA needs to be extended to support taggers which
have both a header and a trailer. Very unconventional - my understanding
is that the trailer exists because the timestamps couldn't be prepared
in time for putting them in the header area.

- Like SJA1105, not all packets sent to the CPU have the DSA tag added
to them, only control packets do:

* the ones which match the destination MAC filters/traps in
MAC_FLTRES1 and MAC_FLTRES0
* the ones which match FDB entries which have TRAP or TAKETS bits set

So we could in theory hack something up to request the switch to take
timestamps for all packets that reach the CPU, and those would be
DSA-tagged and contain the source port / switch ID by virtue of the
fact that there needs to be a timestamp trailer provided. BUT:

- The SJA1110 does not parse its own DSA tags in a way that is useful
for routing in cross-chip topologies, a la Marvell. And the sja1105
driver already supports cross-chip bridging from the SJA1105 days.
It does that by automatically setting up the DSA links as VLAN trunks
which contain all the necessary tag_8021q RX VLANs that must be
communicated between the switches that span the same bridge. So when
using tag_8021q on sja1105, it is possible to have 2 switches with
ports sw0p0, sw0p1, sw1p0, sw1p1, and 2 VLAN-unaware bridges br0 and
br1, and br0 can take sw0p0 and sw1p0, and br1 can take sw0p1 and
sw1p1, and forwarding will happen according to the expected rules of
the Linux bridge.
We like that, and we don't want that to go away, so as a matter of
fact, the SJA1110 tagger still needs to support tag_8021q.

So the sja1110 tagger is a hybrid between tag_8021q for data packets,
and the native hardware support for control packets.

On RX, packets have a 13-byte trailer if they contain an RX timestamp.
That trailer is padded in such a way that its byte 8 (the start of the
"residence time" field - not parsed by Linux because we don't care) is
aligned on a 16 byte boundary. So the padding has a variable length
between 0 and 15 bytes. The DSA header contains the offset of the
beginning of the padding relative to the beginning of the frame (and the
end of the padding is obviously the end of the packet minus 13 bytes,
the length of the trailer). So we discard it.

Packets which don't have a trailer contain the source port and switch ID
information in the header (they are "trap-to-host" packets). Packets
which have a trailer contain the source port and switch ID in the trailer.

On TX, the destination port mask and switch ID is always in the trailer,
so we always need to say in the header that a trailer is present.

The header needs a custom EtherType and this was chosen as 0xdadc, after
0xdada which is for Marvell and 0xdadb which is for VLANs in
VLAN-unaware mode on SJA1105 (and SJA1110 in fact too).

Because we use tag_8021q in concert with the native tagging protocol,
control packets will have 2 DSA tags.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: allow RX timestamps to be taken on all ports for SJA1110

On SJA1105, there is support for a cascade port which is presumably
connected to a downstream SJA1105 switch. The upstream one does not take
PTP timestamps for packets received on this port, presumably because the
downstream switch already did (and for PTP, it only makes sense for the
leaf nodes in a DSA switch tree to do that).

I haven't been able to validate that feature in a fully assembled setup,
so I am disabling the feature by setting the cascade port to an unused
port value (ds->num_ports).

In SJA1110, multiple cascade ports are supported, and CASC_PORT became
a bit mask from a port number. So when CASC_PORT is set to ds->num_ports
(which is 11 on SJA1110), it is actually set to 0b1011, so ports 3, 1
and 0 are configured as cascade ports and we cannot take RX timestamps
on them.

So we need to introduce a check for SJA1110 and set things differently
(to zero there), so that the cascading feature is properly disabled and
RX timestamps can be taken on all ports.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX

The SJA1110 contains two types of integrated PHYs: one 100base-TX PHY
and multiple 100base-T1 PHYs.

The access procedure for the 100base-T1 PHYs is also different than it
is for the 100base-TX one. So we register 2 MDIO buses, one for the
base-TX and the other for the base-T1. Each bus has an OF node which is
a child of the "mdio" subnode of the switch, and they are recognized by
compatible string.

Cc: Russell King <linux@armlinux.org.uk>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: add support for the SJA1110 switch family

The SJA1110 is basically an SJA1105 with more ports, some integrated
PHYs (100base-T1 and 100base-TX) and an embedded microcontroller which
can be disabled, and the switch core can be controlled by a host running
Linux, over SPI.

This patch contains:
- the static and dynamic config packing functions, for the tables that
are common with SJA1105
- one more static config tables which is "unique" to the SJA1110
(actually it is a rehash of stuff that was placed somewhere else in
SJA1105): the PCP Remapping Table
- a reset and clock configuration procedure for the SJA1110 switch.
This resets just the switch subsystem, and gates off the clock which
powers on the embedded microcontroller.
- an RGMII delay configuration procedure for SJA1110, which is very
similar to SJA1105, but different enough for us to be unable to reuse
it (this is a pattern that repeats itself)
- some adaptations to dynamic config table entries which are no longer
programmed in the same way. For example, to delete a VLAN, you used to
write an entry through the dynamic reconfiguration interface with the
desired VLAN ID, and with the VALIDENT bit set to false. Now, the VLAN
table entries contain a TYPE_ENTRY field, which must be set to zero
(in a backwards-incompatible way) in order for the entry to be deleted,
or to some other entry for the VLAN to match "inner tagged" or "outer
tagged" packets.
- a similar thing for the static config: the xMII Mode Parameters Table
encoding for SGMII and MII (the latter just when attached to a
100base-TX PHY) just isn't what it used to be in SJA1105. They are
identical, except there is an extra "special" bit which needs to be
set. Set it.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: add a translation table for port speeds

In order to support the new speed of 2500Mbps, the SJA1110 has achieved
the great performance of changing the encoding in the MAC Configuration
Table for the port speeds of 10, 100, 1000 compared to SJA1105.

Because this is a common driver, we need a layer of indirection in order
to program the hardware with the right values irrespective of switch
generation.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: sja1105: add a PHY interface type compatibility matrix

On the SJA1105, all ports support the parallel "xMII" protocols (MII,
RMII, RGMII) except for port 4 on SJA1105R/S which supports only SGMII.
This was relatively easy to model, by special-casing the SGMII port.

On the SJA1110, certain ports can be pinmuxed between SGMII and xMII, or
between SGMII and an internal 100base-TX PHY. This creates problems,
because the driver's assumption so far was that if a port supports
SGMII, it uses SGMII.

We allow the device tree to tell us how the port pinmuxing is done, and
check that against a PHY interface type compatibility matrix for
plausibility.

The other big change is that instead of doing SGMII configuration based
on what the port supports, we do it based on what is the configured
phy_mode of the port.

The 2500base-x support added in this patch is not complete.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: sja1105: the 0x1F0000 SGMII "base address" is actually MDIO_MMD_VEND2

Looking at the SGMII PCS from SJA1110, which is accessed indirectly
through a different base address as can be seen in the next patch, it
appears odd that the address accessed through indirection still
references the base address from the SJA1105S register map (first MDIO
register is at 0x1f0000), when it could index the SGMII registers
starting from zero.

Except that the 0x1f0000 is not a base address at all, it seems. It is
0x1f << 16 | 0x0000, and 0x1f is coding for the vendor-specific MMD2.
So, it turns out, the Synopsys PCS implements all its registers inside
the vendor-specific MMDs 1 and 2 (0x1e and 0x1f). This explains why the
PCS has no overlaps (for the other MMDs) with other register regions of
the switch (because no other MMDs are implemented).

Change the code to remove the SGMII "base address" and explicitly encode
the MMD for reads/writes. This will become necessary for SJA1110 support.

Cc: Russell King <linux@armlinux.org.uk>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: sja1105: allow the frame buffer size to be customized

The shared frame buffer of the SJA1110 is larger than that of SJA1105,
which is natural due to the fact that there are more ports.

Introduce yet another property in struct sja1105_info which encodes the
maximum number of 128 byte blocks that can be used for frame buffers.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: use sja1105_xfer_u32 for the reset procedure

Using sja1105_xfer_buf results in a higher overhead and is harder to
read.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: skip CGU configuration if it's unnecessary

There are two distinct code paths which enter sja1105_clocking.c, one
through sja1105_clocking_setup() and the other through
sja1105_clocking_setup_port():

sja1105_static_config_reload sja1105_setup
| |
| +------------------+
| |
v v
sja1105_clocking_setup sja1105_adjust_port_config
| |
v |
sja1105_clocking_setup_port <------------------+

As opposed to SJA1105, the SJA1110 does not need any configuration of
the Clock Generation Unit in order for xMII ports to work. Just RGMII
internal delays need to be configured, and that is done inside
sja1105_clocking_setup_port for the RGMII ports.

So this patch introduces the concept of a "reserved address", which the
CGU configuration functions from sja1105_clocking.c must check before
proceeding to do anything. The SJA1110 will have reserved addresses for
the CGU PLLs for MII/RMII/RGMII.

Additionally, make sja1105_clocking_setup() a function pointer so it can
be overridden by the SJA1110. Even though nothing port-related needs to
be done in the CGU, there are some operations such as disabling the
watchdog clock which are unique to the SJA1110.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: parameterize the number of ports

The sja1105 driver will gain support for the next-gen SJA1110 switch,
which is very similar except for the fact it has more than 5 ports.

So we need to replace the hardcoded SJA1105_NUM_PORTS in this driver
with ds->num_ports. This patch is as mechanical as possible (save for
the fact that ds->num_ports is not an integer constant expression).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: don't use burst SPI reads for port statistics

The current internal sja1105 driver API is optimized for retrieving many
statistics counters at once. But the switch does not do atomic snapshotting
for them anyway.

In case we start reporting the hardware port counters through
ndo_get_stats64 as well, not just ethtool, it would be good to be able
to read individual port counters and not all of them.

Additionally, since Arnd Bergmann's commit ae1804de93f6 ("dsa: sja1105:
dynamically allocate stats structure"), sja1105_get_ethtool_stats
allocates memory dynamically, since struct sja1105_port_status was
deemed to consume too much stack memory. That is not ideal.
The large structure is only needed because of the burst read.
If we read statistics one by one, we can consume less memory, and
we can avoid dynamic allocation.

Additionally, latency-sensitive interfaces such as PTP operations (for
phc2sys) might suffer if the SPI mutex is being held for too long, which
happens in the case of SPI burst reads. By reading counters one by one,
we give a chance for higher priority processes to preempt and take the
SPI bus mutex for accessing the PTP clock.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: stop reporting the queue levels in ethtool port counters

The queue levels are not counters, but instead they represent the
occupancy of the MAC TX queues. Having these in ethtool port counters is
not helpful, so remove them.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: adapt to a SPI controller with a limited max transfer size

The static config of the sja1105 switch is a long stream of bytes which
is programmed to the hardware in chunks (portions with the chip select
continuously asserted) of max 256 bytes each. Each chunk is a
spi_message composed of 2 spi_transfers: the buffer with the data and a
preceding buffer with the SPI access header.

Only that certain SPI controllers, such as the spi-sc18is602 I2C-to-SPI
bridge, cannot keep the chip select asserted for that long.
The spi_max_transfer_size() and spi_max_message_size() functions are how
the controller can impose its hardware limitations upon the SPI
peripheral driver.

For the sja1105 driver to work with these controllers, both buffers must
be smaller than the transfer limit, and their sum must be smaller than
the message limit.

Regression-tested on a switch connected to a controller with no
limitations (spi-fsl-dspi) as well as with one with caps for both
max_transfer_size and max_message_size (spi-sc18is602).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: send multiple spi_messages instead of using cs_change

The sja1105 driver has been described by Mark Brown as "not using the
[ SPI ] API at all idiomatically" due to the use of cs_change:
https://patchwork.kernel.org/project/netdevbpf/patch/20210520135031.2969183-1-olteanv@gmail.com/

According to include/linux/spi/spi.h, the chip select is supposed to be
asserted for the entire length of a SPI message, as long as cs_change is
false for all member transfers. The cs_change flag changes the following:

(i) When a non-final SPI transfer has cs_change = true, the chip select
should temporarily deassert and then reassert starting with the next
transfer.
(ii) When a final SPI transfer has cs_change = true, the chip select
should remain asserted until the following SPI message.

The sja1105 driver only uses cs_change for its first property, to form a
single SPI message whose layout can be seen below:

this is an entire, single spi_message
_______________________________________________________________________________________________
/ \
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
| hdr_xfer[0] | chunk_xfer[0] | hdr_xfer[1] | chunk_xfer[1] | | hdr_xfer[n] | chunk_xfer[n] |
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
cs_change false true false true false false

____________________________ _____________________________ _____________________________
CS line __/ \/ \ ... / \__

The fact of the matter is that spi_max_message_size() has an ambiguous
meaning if any non-final transfer has cs_change = true.

If the SPI master has a limitation in that it cannot keep the chip
select asserted for more than, say, 200 bytes (like the spi-sc18is602),
the normal thing for it to do is to implement .max_transfer_size and
.max_message_size, and limit both to 200: in the "worst case" where
cs_change is always false, then the controller can, indeed, not send
messages larger than 200 bytes.

But the fact that the SPI controller's max_message_size does not
necessarily mean that we cannot send messages larger than that.
Notably, if the SPI master special-cases the transfers with cs_change
and treats every chip select toggling as an entirely new transaction,
then a SPI message can easily exceed that limit. So there is a
temptation to ignore the controller's reported max_message_size when
using cs_change = true in non-final transfers.

But that can lead to false conclusions. As Mark points out, the SPI
controller might have a different kind of limitation with the max
message size, that has nothing at all to do with how long it can keep
the chip select asserted.
For example, that might be the case if the device is able to offload the
chip select changes to the hardware as part of the data stream, and it
packs the entire stream of commands+data (corresponding to a SPI
message) into a single DMA transfer that is itself limited in size.

So the only thing we can do is avoid ambiguity by not using cs_change at
all. Instead of sending a single spi_message, we now send multiple SPI
messages as follows:

spi_message 0 spi_message 1 spi_message n
____________________________ ___________________________ _____________________________
/ \ / \ / \
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
| hdr_xfer[0] | chunk_xfer[0] | hdr_xfer[1] | chunk_xfer[1] | | hdr_xfer[n] | chunk_xfer[n] |
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
cs_change false true false true false false

____________________________ _____________________________ _____________________________
CS line __/ \/ \ ... / \__

which is clearer because the max_message_size limit is now easier to
enforce. What is transmitted on the wire stays, of course, the same.

Additionally, because we send no more than 2 transfers at a time, we now
avoid dynamic memory allocation too, which might be seen as an
improvement by some.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: offload bridge port flags to device

The chip can configure unicast flooding, broadcast flooding and learning.
Learning is per port, while flooding is per {ingress, egress} port pair
and we need to configure the same value for all possible ingress ports
towards the requested one.

While multicast flooding is not officially supported, we can hack it by
using a feature of the second generation (P/Q/R/S) devices, which is that
FDB entries are maskable, and multicast addresses always have an odd
first octet. So by putting a match-all for 00:01:00:00:00:00 addr and
00:01:00:00:00:00 mask at the end of the FDB, we make sure that it is
always checked last, and does not take precedence in front of any other
MDB. So it behaves effectively as an unknown multicast entry.

For the first generation switches, this feature is not available, so
unknown multicast will always be treated the same as unknown unicast.
So the only thing we can do is request the user to offload the settings
for these 2 flags in tandem, i.e.

ip link set swp2 type bridge_slave flood off
Error: sja1105: This chip cannot configure multicast flooding independently of unicast.
ip link set swp2 type bridge_slave flood off mcast_flood off
ip link set swp2 type bridge_slave mcast_flood on
Error: sja1105: This chip cannot configure multicast flooding independently of unicast.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: expose static config as devlink region

As explained in Documentation/networking/dsa/sja1105.rst, this switch
has a static config held in the driver's memory and re-uploaded from
time to time into the device (after any major change).

The format of this static config is in fact described in UM10944.pdf and
it contains all the switch's settings (it also contains device ID, table
CRCs, etc, just like in the manual). So it is a useful and universal
devlink region to expose to user space, for debugging purposes.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: make the instantiations of struct sja1105_info constant

Since struct sja1105_private only holds a const pointer to one of these
structures based on device tree compatible string, the structures
themselves can be made const.

Also add an empty line between each structure definition, to appease
checkpatch.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: offload the Credit-Based Shaper qdisc

SJA1105, being AVB/TSN switches, provide hardware assist for the
Credit-Based Shaper as described in the IEEE 8021Q-2018 document.

First generation has 10 shapers, freely assignable to any of the 4
external ports and 8 traffic classes, and second generation has 16
shapers.

The Credit-Based Shaper tables are accessed through the dynamic
reconfiguration interface, so we have to restore them manually after a
switch reset. The tables are backed up by the static config only on
P/Q/R/S, and we don't want to add custom code only for that family,
since the procedure that is in place now works for both.

Tested with the following commands:

data_rate_kbps=67000
port_transmit_rate_kbps=1000000
idleslope=$data_rate_kbps
sendslope=$(($idleslope - $port_transmit_rate_kbps))
locredit=$((-0x80000000))
hicredit=$((0x7fffffff))
tc qdisc add dev swp2 root handle 1: mqprio hw 0 num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7
tc qdisc replace dev swp2 parent 1:1 cbs \
idleslope $idleslope \
sendslope $sendslope \
hicredit $hicredit \
locredit $locredit \
offload 1

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: prepare tagger for handling DSA tags and VLAN simultaneously

In VLAN-unaware mode, sja1105 uses VLAN tags with a custom TPID of
0xdadb. While in the yet-to-be introduced best_effort_vlan_filtering
mode, it needs to work with normal VLAN TPID values.

A complication arises when we must transmit a VLAN-tagged packet to the
switch when it's in VLAN-aware mode. We need to construct a packet with
2 VLAN tags, and the switch will use the outer header for routing and
pop it on egress. But sadly, here the 2 hardware generations don't
behave the same:

- E/T switches won't pop an ETH_P_8021AD tag on egress, it seems
(packets will remain double-tagged).
- P/Q/R/S switches will drop a packet with 2 ETH_P_8021Q tags (it looks
like it tries to prevent VLAN hopping).

But looks like the reverse is also true:

- E/T switches have no problem popping the outer tag from packets with
2 ETH_P_8021Q tags.
- P/Q/R/S will have no problem popping a single tag even if that is
ETH_P_8021AD.

So it is clear that if we want the hardware to work with dsa_8021q
tagging in VLAN-aware mode, we need to send different TPIDs depending on
revision. Keep that information in priv->info->qinq_tpid.

The per-port tagger structure will hold an xmit_tpid value that depends
not only upon the qinq_tpid, but also upon the VLAN awareness state
itself (in case we must transmit using 0xdadb).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: implement tc-gate using time-triggered virtual links

Restrict the TTEthernet hardware support on this switch to operate as
closely as possible to IEEE 802.1Qci as possible. This means that it can
perform PTP-time-based ingress admission control on streams identified
by {DMAC, VID, PCP}, which is useful when trying to ensure the
determinism of traffic scheduled via IEEE 802.1Qbv.

The oddity comes from the fact that in hardware (and in TTEthernet at
large), virtual links always need a full-blown action, including not
only the type of policing, but also the list of destination ports. So in
practice, a single tc-gate action will result in all packets getting
dropped. Additional actions (either "trap" or "redirect") need to be
specified in the same filter rule such that the conforming packets are
actually forwarded somewhere.

Apart from the VL Lookup, Policing and Forwarding tables which need to
be programmed for each flow (virtual link), the Schedule engine also
needs to be told to open/close the admission gates for each individual
virtual link. A fairly accurate (and detailed) description of how that
works is already present in sja1105_tas.c, since it is already used to
trigger the egress gates for the tc-taprio offload (IEEE 802.1Qbv). Key
point here, we remember that the schedule engine supports 8
"subschedules" (execution threads that iterate through the global
schedule in parallel, and that no 2 hardware threads must execute a
schedule entry at the same time). For tc-taprio, each egress port used
one of these 8 subschedules, leaving a total of 4 subschedules unused.
In principle we could have allocated 1 subschedule for the tc-gate
offload of each ingress port, but actually the schedules of all virtual
links installed on each ingress port would have needed to be merged
together, before they could have been programmed to hardware. So
simplify our life and just merge the entire tc-gate configuration, for
all virtual links on all ingress ports, into a single subschedule. Be
sure to check that against the usual hardware scheduling conflicts, and
program it to hardware alongside any tc-taprio subschedule that may be
present.

The following scenarios were tested:

1. Quantitative testing:

tc qdisc add dev swp2 clsact
tc filter add dev swp2 ingress flower skip_sw \
dst_mac 42:be:24:9b:76:20 \
action gate index 1 base-time 0 \
sched-entry OPEN 1200 -1 -1 \
sched-entry CLOSE 1200 -1 -1 \
action trap

ping 192.168.1.2 -f
PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
.............................
--- 192.168.1.2 ping statistics ---
948 packets transmitted, 467 received, 50.7384% packet loss, time 9671ms

2. Qualitative testing (with a phase-aligned schedule - the clocks are
synchronized by ptp4l, not shown here):

Receiver (sja1105):

tc qdisc add dev swp2 clsact
now=$(phc_ctl /dev/ptp1 get | awk '/clock time is/ {print $5}') && \
sec=$(echo $now | awk -F. '{print $1}') && \
base_time="$(((sec + 2) * 1000000000))" && \
echo "base time ${base_time}"
tc filter add dev swp2 ingress flower skip_sw \
dst_mac 42:be:24:9b:76:20 \
action gate base-time ${base_time} \
sched-entry OPEN 60000 -1 -1 \
sched-entry CLOSE 40000 -1 -1 \
action trap

Sender (enetc):
now=$(phc_ctl /dev/ptp0 get | awk '/clock time is/ {print $5}') && \
sec=$(echo $now | awk -F. '{print $1}') && \
base_time="$(((sec + 2) * 1000000000))" && \
echo "base time ${base_time}"
tc qdisc add dev eno0 parent root taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time ${base_time} \
sched-entry S 01 50000 \
sched-entry S 00 50000 \
flags 2

ping -A 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
...
^C
--- 192.168.1.1 ping statistics ---
1425 packets transmitted, 1424 packets received, 0% packet loss
round-trip min/avg/max = 0.322/0.361/0.990 ms

And just for comparison, with the tc-taprio schedule deleted:

ping -A 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
...
^C
--- 192.168.1.1 ping statistics ---
33 packets transmitted, 19 packets received, 42% packet loss
round-trip min/avg/max = 0.336/0.464/0.597 ms

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: enable internal pull-down for RX_DV/CRS_DV/RX_CTL and RX_ER

Some boards do not have the RX_ER MII signal connected. Normally in such
situation, those pins would be grounded, but then again, some boards
left it electrically floating.

When sending traffic to those switch ports, one can see that the
N_SOFERR statistics counter is incrementing once per each packet. The
user manual states for this counter that it may count the number of
frames "that have the MII error input being asserted prior to or
up to the SOF delimiter byte". So the switch MAC is sampling an
electrically floating signal, and preventing proper traffic reception
because of that.

As a workaround, enable the internal weak pull-downs on the input pads
for the MII control signals. This way, a floating signal would be
internally tied to ground.

The logic levels of signals which _are_ externally driven should not be
bothered by this 40-50 KOhm internal resistor. So it is not an issue to
enable the internal pull-down unconditionally, irrespective of PHY
interface type (MII, RMII, RGMII, SGMII) and of board layout.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: show more ethtool statistics counters for P/Q/R/S

It looks like the P/Q/R/S series supports some more counters,
generically named "Ethernet statistics counter", which we were not
printing. Add them.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: configure the PTP_CLK pin as EXT_TS or PER_OUT

The SJA1105 switch family has a PTP_CLK pin which emits a signal with
fixed 50% duty cycle, but variable frequency and programmable start time.

On the second generation (P/Q/R/S) switches, this pin supports even more
functionality. The use case described by the hardware documents talks
about synchronization via oneshot pulses: given 2 sja1105 switches,
arbitrarily designated as a master and a slave, the master emits a
single pulse on PTP_CLK, while the slave is configured to timestamp this
pulse received on its PTP_CLK pin (which must obviously be configured as
input). The difference between the timestamps then exactly becomes the
slave offset to the master.

The only trouble with the above is that the hardware is very much tied
into this use case only, and not very generic beyond that:
- When emitting a oneshot pulse, instead of being told when to emit it,
the switch just does it "now" and tells you later what time it was,
via the PTPSYNCTS register. [ Incidentally, this is the same register
that the slave uses to collect the ext_ts timestamp from, too. ]
- On the sync slave, there is no interrupt mechanism on reception of a
new extts, and no FIFO to buffer them, because in the foreseen use
case, software is in control of both the master and the slave pins,
so it "knows" when there's something to collect.

These 2 problems mean that:
- We don't support (at least yet) the quirky oneshot mode exposed by
the hardware, just normal periodic output.
- We abuse the hardware a little bit when we expose generic extts.
Because there's no interrupt mechanism, we need to poll at double the
frequency we expect to receive a pulse. Currently that means a
non-configurable "twice a second".

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Add support for the SGMII port

SJA1105 switches R and S have one SerDes port with an 802.3z
quasi-compatible PCS, hardwired on port 4. The other ports are still
MII/RMII/RGMII. The PCS performs rate adaptation to lower link speeds;
the MAC on this port is hardwired at gigabit. Only full duplex is
supported.

The SGMII port can be configured as part of the static config tables, as
well as through a dedicated SPI address region for its pseudo-clause-22
registers. However it looks like the static configuration is not
able to change some out-of-reset values (like the value of MII_BMCR), so
at the end of the day, having code for it is utterly pointless. We are
just going to use the pseudo-C22 interface.

Because the PCS gets reset when the switch resets, we have to add even
more restoration logic to sja1105_static_config_reload, otherwise the
SGMII port breaks after operations such as enabling PTP timestamping
which require a switch reset.

>From PHYLINK perspective, the switch supports *only* SGMII (it doesn't
support 1000Base-X). It also doesn't expose access to the raw config
word for in-band AN in registers MII_ADV/MII_LPA.
It is able to work in the following modes:
- Forced speed
- SGMII in-band AN slave (speed received from PHY)
- SGMII in-band AN master (acting as a PHY)

The latter mode is not supported by this patch. It is even unclear to me
how that would be described. There is some code for it left in the
patch, but 'an_master' is always passed as false.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Simplify reset handling

We don't really need 10k species of reset. Remove everything except cold
reset which is what is actually used. Too bad the hardware designers
couldn't agree to use the same bit field for rev 1 and rev 2, so the
(*reset_cmd) function pointer is there to stay.

However let's simplify the prototype and give it a struct dsa_switch (we
want to avoid forward-declarations of structures, in this case struct
sja1105_private, wherever we can).

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Implement state machine for TAS with PTP clock source

Tested using the following bash script and the tc from iproute2-next:

#!/bin/bash

set -e -u -o pipefail

NSEC_PER_SEC="1000000000"

gatemask() {
local tc_list="$1"
local mask=0

for tc in ${tc_list}; do
mask=$((${mask} | (1 << ${tc})))
done

printf "%02x" ${mask}
}

if ! systemctl is-active --quiet ptp4l; then
echo "Please start the ptp4l service"
exit
fi

now=$(phc_ctl /dev/ptp1 get | gawk '/clock time is/ { print $5; }')
# Phase-align the base time to the start of the next second.
sec=$(echo "${now}" | gawk -F. '{ print $1; }')
base_time="$(((${sec} + 1) * ${NSEC_PER_SEC}))"

tc qdisc add dev swp5 parent root handle 100 taprio \
num_tc 8 \
map 0 1 2 3 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time ${base_time} \
sched-entry S $(gatemask 7) 100000 \
sched-entry S $(gatemask "0 1 2 3 4 5 6") 400000 \
clockid CLOCK_TAI flags 2

The "state machine" is a workqueue invoked after each manipulation
command on the PTP clock (reset, adjust time, set time, adjust
frequency) which checks over the state of the time-aware scheduler.
So it is not monitored periodically, only in reaction to a PTP command
typically triggered from a userspace daemon (linuxptp). Otherwise there
is no reason for things to go wrong.

Now that the timecounter/cyclecounter has been replaced with hardware
operations on the PTP clock, the TAS Kconfig now depends upon PTP and
the standalone clocksource operating mode has been removed.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Make the PTP command read-write

The PTPSTRTSCH and PTPSTOPSCH bits are actually readable and indicate
whether the time-aware scheduler is running or not. We will be using
that for monitoring the scheduler in the next patch, so refactor the PTP
command API in order to allow that.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Restore PTP time after switch reset

The PTP time of the switch is not preserved when uploading a new static
configuration. Work around this hardware oddity by reading its PTP time
before a static config upload, and restoring it afterwards.

Static config changes are expected to occur at runtime even in scenarios
directly related to PTP, i.e. the Time-Aware Scheduler of the switch is
programmed in this way.

Perhaps the larger implication of this patch is that the PTP .gettimex64
and .settime functions need to be exposed to sja1105_main.c, where the
PTP lock needs to be held during this entire process. So their core
implementation needs to move to some common functions which get exposed
in sja1105_ptp.h.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Implement the .gettimex64 system call for PTP

Through the PTP_SYS_OFFSET_EXTENDED ioctl, it is possible for userspace
applications (i.e. phc2sys) to compensate for the delays incurred while
reading the PHC's time.

The task itself of taking the software timestamp is delegated to the SPI
subsystem, through the newly introduced API in struct spi_transfer. The
goal is to cross-timestamp I/O operations on the switch's PTP clock with
values in the local system clock (CLOCK_REALTIME). For that we need to
understand a bit of the hardware internals.

The 'read PTP time' message is a 12 byte structure, first 4 bytes of
which represent the SPI header, and the last 8 bytes represent the
64-bit PTP time. The switch itself starts processing the command
immediately after receiving the last bit of the address, i.e. at the
middle of byte 3 (last byte of header). The PTP time is shadowed to a
buffer register in the switch, and retrieved atomically during the
subsequent SPI frames.

A similar thing goes on for the 'write PTP time' message, although in
that case the switch waits until the 64-bit PTP time becomes fully
available before taking any action. So the byte that needs to be
software-timestamped is byte 11 (last) of the transfer.

The patch creates a common (and local) sja1105_xfer implementation for
the SPI I/O, and offers 3 front-ends:

- sja1105_xfer_u32 and sja1105_xfer_u64: these are capable of optionally
requesting a PTP timestamp

- sja1105_xfer_buf: this is for large transfers (e.g. the static config
buffer) and other misc data, and there is no point in giving
timestamping capabilities to this.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Switch to hardware operations for PTP

Adjusting the hardware clock (PTPCLKVAL, PTPCLKADD, PTPCLKRATE) is a
requirement for the auxiliary PTP functionality of the switch
(TTEthernet, PPS input, PPS output).

Therefore we need to switch to using these registers to keep a
synchronized time in hardware, instead of the timecounter/cyclecounter
implementation, which is reliant on the free-running PTPTSCLK.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Switch to scatter/gather API for SPI

This reworks the SPI transfer implementation to make use of more of the
SPI core features. The main benefit is to avoid the memcpy in
sja1105_xfer_buf().

The memcpy was only needed because the function was transferring a
single buffer at a time. So it needed to copy the caller-provided buffer
at buf + 4, to store the SPI message header in the "headroom" area.

But the SPI core supports scatter-gather messages, comprised of multiple
transfers. We can actually use those to break apart every SPI message
into 2 transfers: one for the header and one for the actual payload.

To keep the behavior the same regarding the chip select signal, it is
necessary to tell the SPI core to de-assert the chip select after each
chunk. This was not needed before, because each spi_message contained
only 1 single transfer.

The meaning of the per-transfer cs_change=1 is:

- If the transfer is the last one of the message, keep CS asserted
- Otherwise, deassert CS

We need to deassert CS in the "otherwise" case, which was implicit
before.

Avoiding the memcpy creates yet another opportunity. The device can't
process more than 256 bytes of SPI payload at a time, so the
sja1105_xfer_long_buf() function used to exist, to split the larger
caller buffer into chunks.

But these chunks couldn't be used as scatter/gather buffers for
spi_message until now, because of that memcpy (we would have needed more
memory for each chunk). So we can now remove the sja1105_xfer_long_buf()
function and have a single implementation for long and short buffers.

Another benefit is lower usage of stack memory. Previously we had to
store 2 SPI buffers for each chunk. Due to the elimination of the
memcpy, we can now send pointers to the actual chunks from the
caller-supplied buffer to the SPI core.

Since the patch merges two functions into a rewritten implementation,
the function prototype was also changed, mainly for cosmetic consistency
with the structures used within it.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Move sja1105_spi_transfer into sja1105_xfer

This is a cosmetic patch that reduces some boilerplate in the SPI
interaction of the driver.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Make all public PTP functions take dsa_switch as argument

The new rule (as already started for sja1105_tas.h) is for functions of
optional driver components (ones which may be disabled via Kconfig - PTP
and TAS) to take struct dsa_switch *ds instead of struct sja1105_private
*priv as first argument.

This is so that forward-declarations of struct sja1105_private can be
avoided.

So make sja1105_ptp.h the second user of this rule.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Make function sja1105_xfer_long_buf static

Fix sparse warnings:

drivers/net/dsa/sja1105/sja1105_spi.c:159:5: warning: symbol 'sja1105_xfer_long_buf' was not declared. Should it be static?

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Rename sja1105_spi_send_packed_buf to sja1105_xfer_buf

The most commonly called function in the driver is long due for a
rename. The "packed" word is redundant (it doesn't make sense to
transfer an unpacked structure, since that is in CPU endianness yadda
yadda), and the "spi" word is also redundant since argument 2 of the
function is SPI_READ or SPI_WRITE.

As for the sja1105_spi_send_long_packed_buf function, it is only being
used from sja1105_spi.c, so remove its global prototype.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Replace sja1105_spi_send_int with sja1105_xfer_{u32, u64}

Having a function that takes a variable number of unpacked bytes which
it generically calls an "int" is confusing and makes auditing patches
next to impossible.

We only use spi_send_int with the int sizes of 32 and 64 bits. So just
make the spi_send_int function less generic and replace it with the
appropriate two explicit functions, which can now type-check the int
pointer type.

Note that there is still a small weirdness in the u32 function, which
has to convert it to a u64 temporary. This is because of how the packing
API works at the moment, but the weirdness is at least hidden from
callers of sja1105_xfer_u32 now.

Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Prevent leaking memory

In sja1105_static_config_upload, in two cases memory is leaked: when
static_config_buf_prepare_for_upload fails and when sja1105_inhibit_tx
fails. In both cases config_buf should be released.

Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Fixes: 1a4c69406cc1 ("net: dsa: sja1105: Prevent PHY jabbering during switch reset")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Build PTP support in main DSA driver

As Arnd Bergmann pointed out in commit 78fe8a28fb96 ("net: dsa: sja1105:
fix ptp link error"), there is no point in having PTP support as a
separate loadable kernel module.

So remove the exported symbols and make sja1105.ko contain PTP support
or not based on CONFIG_NET_DSA_SJA1105_PTP.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Add RGMII delay support for P/Q/R/S chips

As per the DT phy-mode specification, RGMII delays are applied by the
MAC when there is no PHY present on the link.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Remove duplicate rgmii_pad_mii_tx from regs

The pad_mii_tx registers point to the same memory region but were
unused. So convert to using these for RGMII I/O cell configuration, as
they bear a shorter name.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Export the sja1105_inhibit_tx function

This will be used to stop egress traffic in .phylink_mac_link_up.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Add logic for TX timestamping

On TX, timestamping is performed synchronously from the
port_deferred_xmit worker thread.
In management routes, the switch is requested to take egress timestamps
(again partial), which are reconstructed and appended to a clone of the
skb that was just sent. The cloning is done by DSA and we retrieve the
pointer from the structure that DSA keeps in skb->cb.
Then these clones are enqueued to the socket's error queue for
application-level processing.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Add support for the PTP clock

The design of this PHC driver is influenced by the switch's behavior
w.r.t. timestamping. It exposes two PTP counters, one free-running
(PTPTSCLK) and the other offset- and frequency-corrected in hardware
through PTPCLKVAL, PTPCLKADD and PTPCLKRATE. The MACs can sample either
of these for frame timestamps.

However, the user manual warns that taking timestamps based on the
corrected clock is less than useful, as the switch can deliver corrupted
timestamps in a variety of circumstances.

Therefore, this PHC uses the free-running PTPTSCLK together with a
timecounter/cyclecounter structure that translates it into a software
time domain. Thus, the settime/adjtime and adjfine callbacks are
hardware no-ops.

The timestamps (introduced in a further patch) will also be translated
to the correct time domain before being handed over to the userspace PTP
stack.

The introduction of a second set of PHC operations that operate on the
hardware PTPCLKVAL/PTPCLKADD/PTPCLKRATE in the future is somewhat
unavoidable, as the TTEthernet core uses the corrected PTP time domain.
However, the free-running counter + timecounter structure combination
will suffice for now, as the resulting timestamps yield a sub-50 ns
synchronization offset in steady state using linuxptp.

For this patch, in absence of frame timestamping, the operations of the
switch PHC were tested by syncing it to the system time as a local slave
clock with:

phc2sys -s CLOCK_REALTIME -c swp2 -O 0 -m -S 0.01

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Export symbols for upcoming PTP driver

These are needed for the situation where the switch driver and the PTP
driver are both built as modules.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Make room for P/Q/R/S FDB operations

The DSA callbacks were written with the E/T (first generation) in mind,
which is quite different.

For P/Q/R/S completely new implementations need to be provided, which
are held as function pointers in the priv->info structure. We are
taking a slightly roundabout way for this (a function from
sja1105_main.c reads a structure defined in sja1105_spi.c that
points to a function defined in sja1105_main.c), but it is what it is.

The FDB dump callback works for both families, hence no function pointer
for that.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: fix check on while loop exit

The while-loop exit condition check is not correct; the
loop should continue if the returns from the function calls are
negative or the CRC status returns are invalid. Currently it
is ignoring the returns from the function calls. Fix this by
removing the status return checks and only break from the loop
at the very end when we know that all the success condtions have
been met.

Kudos to Dan Carpenter for describing the correct fix and
Vladimir Oltean for noting the change to the check on the number
of retries.

Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Make 'sja1105et_regs' and 'sja1105pqrs_regs' static

drivers/net/dsa/sja1105/sja1105_spi.c:486:21: warning: symbol 'sja1105et_regs' was not declared. Should it be static?
drivers/net/dsa/sja1105/sja1105_spi.c:511:21: warning: symbol 'sja1105pqrs_regs' was not declared. Should it be static?

Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Prevent PHY jabbering during switch reset

Resetting the switch at runtime is currently done while changing the
vlan_filtering setting (due to the required TPID change).

But reset is asynchronous with packet egress, and the switch core will
not wait for egress to finish before carrying on with the reset
operation.

As a result, a connected PHY such as the BCM5464 would see an
unterminated Ethernet frame and start to jabber (repeat the last seen
Ethernet symbols - jabber is by definition an oversized Ethernet frame
with bad FCS). This behavior is strange in itself, but it also causes
the MACs of some link partners (such as the FRDM-LS1012A) to completely
lock up.

So as a remedy for this situation, when switch reset is required, simply
inhibit Tx on all ports, and wait for the necessary time for the
eventual one frame left in the egress queue (not even the Tx inhibit
command is instantaneous) to be flushed.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch

At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.

IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>