net: dsa: mv88e6xxx: add Amethyst specific SMI GPIO function

The existing mv88e6390_g2_scratch_gpio_set_smi() cannot be used on the
88E6393X as it requires certain P0_MODE, it also checks the CPU mode
as it impacts the bit setting value.

This is all irrelevant for Amethyst (MV88E6191X/6193X/6393X) as only
the default value of the SMI_PHY Config bit is set to CPU_MGD bootstrap
pin value but it can be changed without restrictions so that GPIO pins
9 and 10 are used as SMI pins.

So, introduce Amethyst specific function and call that if the Amethyst
family wants to setup the external PHY.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: mv88e6xxx: rename mv88e6xxx_g2_scratch_gpio_set_smi

The name mv88e6xxx_g2_scratch_gpio_set_smi is a bit ambiguous as it appears
to only be applicable to the 6390 family, so lets rename it to
mv88e6390_g2_scratch_gpio_set_smi to make it more obvious.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent

Since commit 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:

mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done

This board does not have an EEPROM attached to the switch though.

This problem is well explained by Andrew Lunn:

"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.

The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.

However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.

We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:

bit 15 is:

EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
operation (see EEOp below). Only one EEPROM operation can be
executing at one time so this bit must be zero before setting it to
a one. When the requested EEPROM operation completes this bit will
automatically be cleared to a zero. The transition of this bit from
a one to a zero can be used to generate an interrupt (the EEInt in
Global 1, offset 0x00).

and more interesting is bit 11:

Register Loader Running. This bit is set to one whenever the
register loader is busy executing instructions contained in the
EEPROM."

Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.

Fixes: 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Reset mv88e6393x force WD event bit

The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.

Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.

Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family"
Signed-off-by: Gustav Ekelund <gustaek@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Separate C22 and C45 transactions

The global2 SMI MDIO bus driver can perform both C22 and C45
transfers. Create separate functions for each and register the C45
versions using the new API calls where appropriate. Update the SERDES
code to make use of these new accessors.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: mv88e6xxx: Allow external SMI if serial

p0_mode set to one of the supported serial mode should not prevent
configuring the external SMI interface in
mv88e6xxx_g2_scratch_gpio_set_smi. The current masking of the p0_mode
only checks the first 2 bits. This results in switches supporting
serial mode cannot setup external SMI on certain serial modes
(Ex: 1000BASE-X and SGMII).

Extend the mask of the p0_mode to include the reduced modes and
serial modes as allowed modes for the external SMI interface.

Signed-off-by: Marcus Carlberg <marcus.carlberg@axis.com>
Link: https://lore.kernel.org/r/20220824093706.19049-1-marcus.carlberg@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: mv88e6xxx: add mv88e6352_g2_scratch_port_has_serdes()

Read the hardware configuration to determine which port is attached
to the serdes.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Export cross-chip PVT as devlink region

Export the raw PVT data in a devlink region so that it can be
inspected from userspace and compared to the current bridge
configuration.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Correct spelling of define "ADRR" -> "ADDR"

Because ADRR is not a thing.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: add support for mv88e6393x family

The Marvell 88E6393X device is a single-chip integration of a 11-port
Ethernet switch with eight integrated Gigabit Ethernet (GbE)
transceivers and three 10-Gigabit interfaces.

This patch adds functionalities specific to mv88e6393x family (88E6393X,
88E6193X and 88E6191X).

The main differences between previous devices and this one are:
- port 0 can be a SERDES port
- all SERDESes are one-lane, eg. no XAUI nor RXAUI
- on the other hand the SERDESes can do USXGMII, 10GBASER and 5GBASER
(on 6191X only one SERDES is capable of more than 1g; USXGMII is not
yet supported with this change)
- Port Policy CTL register is changed to Port Policy MGMT CTL register,
via which several more registers can be accessed indirectly
- egress monitor port is configured differently
- ingress monitor/CPU/mirror ports are configured differently and can be
configured per port (ie. each port can have different ingress monitor
port, for example)
- port speed AltBit works differently than previously
- PHY registers can be also accessed via MDIO address 0x18 and 0x19
(on previous devices they could be accessed only via Global 2 offsets
0x18 and 0x19, which means two indirections; this feature is not yet
leveraged with thiis commit)

Co-developed-by: Ashkan Boldaji <ashkan.boldaji@digi.com>
Signed-off-by: Ashkan Boldaji <ashkan.boldaji@digi.com>
Signed-off-by: Pavana Sharma <pavana.sharma@digi.com>
Co-developed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Make global2 support mandatory

Early generations of the mv88e6xxx did not have the global 2
registers. In order to keep the driver slim, it was decided to make
the code for these registers optional. Over time, more generations of
switches have been added, always supporting global 2 and adding more
and more registers. No effort has been made to keep these additional
registers also optional to slim the driver down when used for older
generations. Optional global 2 now just gives additional development
and maintenance burden for no real gain.

Make global 2 support always compiled in.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20210127003210.663173-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: mv88e6xxx: Provide dummy implementations for trunk setters

Support for Global 2 registers is build-time optional. In the case
where it was not enabled the build would fail as no "dummy"
implementation of these functions was available.

Fixes: 57e661aae6a8 ("net: dsa: mv88e6xxx: Link aggregation support")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: mv88e6xxx: Link aggregation support

Support offloading of LAGs to hardware. LAGs may be attached to a
bridge in which case VLANs, multicast groups, etc. are also offloaded
as usual.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: mv8e6xxx: Fix stub function parameters

mv88e6xxx_g2_atu_stats_get() takes two parameters. Make the stub
function also take two, otherwise we get compile errors.

Fixes: c5f299d59261 ("net: dsa: mv88e6xxx: global1_atu: Add helper for get next")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: global1_atu: Add helper for get next

When retrieving the ATU statistics, and ATU get next has to be
performed to trigger the ATU to collect the statistics. Export a
helper from global1_atu to perform this.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: global2: Expose ATU stats register

Add helpers to set/get the ATU statistics register.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: remove wait and update routines

Now that we have proper Wait Bit and Wait Mask routines, remove the
unused mv88e6xxx_wait routine and its Global 1 and Global 2 variants.

The indirect tables such as the Device Mapping Table or Priority
Override Table make use of an Update bit to distinguish reading (0)
from writing (1) operations. After a write operation occurs, the bit
self clears right away so there's no need to wait on it. Thus keep
things simple and remove the mv88e6xxx_update helper as well.

Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: introduce wait bit routine

Many portions of the driver need to wait until a given bit is set
or cleared. Some busses even have a specific implementation for this
operation. In preparation for such variant, implement a generic Wait
Bit routine that can be used by the driver core functions.

This allows us to get rid of the custom implementations we may find
in the driver. Note that for the EEPROM bits, BUSY and RUNNING bits
are independent, thus it is more efficient to wait independently for
each bit instead of waiting for their mask.

Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: implement watchdog_ops for mv88e6250

The MV88E6352_G2_WDOG_CTL_* bits almost, but not quite, describe the
watchdog control register on the mv88e6250. Among those actually
referenced in the code, only QC_ENABLE differs (bit 6 rather than bit
5).

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: mv88e6xxx: Add MV88E6165 AVB register access

The MV88E6165 PTP registers are all in AVB bank F, unlike newer
generations which spread them over AVB bank E and F. Implement AVB ops
for the MV88E6165 which hides this difference.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: remove Global 2 setup

The remaining values written to the Switch Management Register in the
mv88e6xxx_g2_setup function are specific to 88E6352 and older, and are
the default values anyway.

Thus remove completely this function. The mv88e6xxx driver no more
contains setup code to access arbitrary Global 2 registers.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: move device mapping setup

Move the Device Mapping setup out of the specific Global 2 code,
into the top level device setup function.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: move trunk setup

Move the trunking setup out of Global 2 specific setup into the top
level mv88e6xxx_setup function.

Note that the 88E6390 family calls this LAG instead of Trunk and
supports 32 possible ID routing vectors, with LAG ID bit 4 being placed
in Global 2 register 0x1D...

We don't need Trunk (or LAG) IDs for the moment, thus keep it simple.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Add MDIO interrupts for internal PHYs

When registering an MDIO bus, it is possible to pass an array of
interrupts, one per address on the bus. phylib will then associate the
interrupt to the PHY device, if no other interrupt is provided.

Some of the global2 interrupts are PHY interrupts. Place them into the
MDIO bus structure.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

dsa: ptp: mark dummy helpers as 'inline'

Declaring a static function in a header leads to a warning every
time that header gets included without the function being used:

In file included from drivers/net/dsa/mv88e6xxx/chip.c:42:
drivers/net/dsa/mv88e6xxx/ptp.h:92:13: error: 'mv88e6xxx_hwtstamp_work' defined but not used [-Werror=unused-function]
static long mv88e6xxx_hwtstamp_work(struct ptp_clock_info *ptp)
In file included from drivers/net/dsa/mv88e6xxx/chip.c:38:
drivers/net/dsa/mv88e6xxx/global2.h:355:12: error: 'mv88e6xxx_g2_wait' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_wait(struct mv88e6xxx_chip *chip, int reg, u16 mask)
^~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:350:12: error: 'mv88e6xxx_g2_update' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_update(struct mv88e6xxx_chip *chip, int reg, u16 update)
^~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:345:12: error: 'mv88e6xxx_g2_write' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_write(struct mv88e6xxx_chip *chip, int reg, u16 val)
^~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:340:12: error: 'mv88e6xxx_g2_read' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_read(struct mv88e6xxx_chip *chip, int reg, u16 *val)

This marks all such functions in dsa inline to make sure we don't warn
about them.

Fixes: c6fe0ad2c349 ("net: dsa: mv88e6xxx: add rx/tx timestamping support")
Fixes: 0d632c3d6fe3 ("net: dsa: mv88e6xxx: add accessors for PTP/TAI registers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: scratch registers and external MDIO pins

MV88E6352 and later switches support GPIO control through the "Scratch
& Misc" global2 register. Two of the pins controlled this way on the
mv88e6390 family are the external MDIO pins. They can either by used
as part of the MII interface for port 0, GPIOs, or MDIO. Add a
function to configure them for MDIO, if possible, and call it when
registering the external MDIO bus.

Suggested-by: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: add support for GPIO configuration

MV88E6352 and later switches support GPIO control through the "Scratch
& Misc" global2 register. (Older switches do too, though with a slightly
different register interface. Only the 6352-style is implemented here.)

Add a new file, global2_scratch.c, for operations in the Scratch & Misc
space. Additionally, add a GPIO operations structure to present an
abstract view over GPIO manipulation.

Reverse Christmas tree and unsigned has been replaced with unsigned
int by Andrew Lunn.

Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: add accessors for PTP/TAI registers

This patch implements support for accessing the Precision Time Protocol
and Time Application Interface registers via the AVB register interface
in the Global 2 register.

The register interface differs slightly between different models; older
models use a 3-bit operations field, while newer models use a 2-bit
field. The operations values and the special "global port" values are
different between the two. This is a similar split to the differences
in the "Ingress Rate" register between models, so, like in that case,
we call the two variants "6352" and "6390" and create an ops structure
to abstract between the two.

checkpatch fixups by Andrew Lunn

Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: export g2 register accessors

Let the mv88e6xxx_g2_* register accessor functions be accessible
outside of global2.c.

Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: add a global2_addr info flag

Similarly to global1_addr, add a global2_addr member in the info
structure to describe the presence of the Global 2 Registers.

This allows us to get rid of the MV88E6XXX_FLAG_GLOBAL2 flag.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: add POT operation

Add a pot_clear operation to clear the Priority Override Table and wrap
its call into a mv88e6xxx_pot_setup helper.

This allows us to get rid of the MV88E6XXX_FLAG_G2_POT flag.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: distinguish Global 2 Rsvd2CPU

The 88E6185 family only has one 16-bit register to mark the 16 802.1D
reserved multicast addresses in the range of 01:80:C2:00:00:0x as MGMT.

The 88E6352 family also has one 16-bit register to mark the 16 GARP
reserved multicast addresses in the range of 01:80:C2:00:00:2x as MGMT.

Split the existing mv88e6095 prefixed mgmt_rsvd2cpu operation into two
distinct mv88e6185 and mv88e6352 prefixed operations, and wrap its call
into a mv88e6xxx_rsvd2cpu_setup helper.

This allows us to also get rid of the MV88E6XXX_CAP_G2_MGMT_EN_* flags.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: add number of Global 2 IRQs

Similarly to g1_irqs, add a g2_irqs member to the info structure to
indicates the presence of the Global 2 Interrupt Source and Mask
registers.

At the same time, provide helpers and document the registers since they
differ a bit between 88E6352 and 88E6390 families.

This allows us to get rid of the MV88E6XXX_FLAG_G2_INT flag.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: prefix Global 2 remaining macros

Prefix and document the remaining Global 2 registers macros.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: prefix Global 2 Watchdog macros

The Marvell 88E6352 family has a Global 2 register dedicated to the
watchdog setup. But the 88E6390 turned it into an indirect table.

Prefix and document that.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: prefix Global 2 Switch MAC macros

Prefix and document the Global 2 Switch MAC registers macros.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: prefix Global 2 EEPROM macros

Prefix and document the Global 2 EEPROM registers macros.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: prefix Global 2 PVT macros

Prefix and document the Global 2 Cross-chip Port VLAN registers macros.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: prefix Global 2 MGMT macros

Prefix and document the Global 2 MGMT registers macros.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: prefix Global 2 Device Mapping macros

Prefix and document the Global 2 Device Mapping macros.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: prefix Global 2 Trunk macros

Prefix and document the Global 2 Trunk registers macros. At the same
time, fix the hask -> hash typo and use the mv88e6xxx_port_mask helper.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: clarify SMI PHY functions

Marvell chips with an SMI PHY access in Global 2 registers handle both
Clause 22 and Clause 45 of IEEE 802.3.

The 88E6390 family has addition bits to target the internal or external
PHYs connected to the device, and a Setup function in addition to the
default (register) Access function.

Prefix the SMI PHY Command and Data registers macros, implement clear
helpers for Clause 22 and 44 Access functions, rename variable to match
the SMI and switch vocabulary (device and register addresses for Clause
22 and port and device class for Clause 45.)

Finally do not use complex macros but simple 16-bit mask to document the
registers organization.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: add irl_init_all op

Some Marvell chips have an Ingress Rate Limit unit. But the command
values slightly differs between models: 88E6352 use 3-bit for operations
while 88E6390 use different 2-bit operations.

This commit kills the IRL flags in favor of a new operation implementing
the "Init all resources to the initial state" operation.

This fixes the operation of 88E6390 family where 0x1000 means Read the
selected resource 0, register 0 on port 16, instead of init all.

A mv88e6xxx_irl_setup helper is added to wrap the operation call.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: move the Global 2 macros

Move the GLOBAL2_* macros where they belong, in the related global2.h
header.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: rename chip header

The mv88e6xxx.h is meant to contains the chip structures and data.
Rename it to chip.h, as for other source/header pairs of the driver.

At the same time, ensure that relative header inclusions are separated
by a newline and sorted alphabetically.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Add missing static to stub functions

'static' was not enough, the helpers must be 'static inline'

net/dsa/mv88e6xxx/global2.h:123:12: error: 'mv88e6xxx_g2_misc_4_bit_port' defined but not used [-Werror=unused-function]
net/dsa/mv88e6xxx/global2.h:117:12: error: 'mv88e6xxx_g2_pvt_write' defined but not used [-Werror=unused-function]

Fixes: c21fbe29f858 ("net: dsa: mv88e6xxx: Add missing static to stub functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Add missing static to stub functions

Stub functions in header files need to be static, or we can have
multiple definitions errors.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 6335e9f2446b ("net: dsa: mv88e6xxx: mv88e6390X SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: program the PVT with all ones

The Cross-chip Port Based VLAN Table (PVT) is currently initialized with
all ones, allowing any external ports to egress frames on local ports.

This commit implements the PVT access functions and programs the PVT
with all ones for the local switch ports only, instead of using the Init
operation. The current behavior is unchanged for the moment.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: use 4-bit port for PVT data

The Cross-chip Port Based VLAN Table (PVT) supports two indexing modes,
one using 5-bit for device and 4-bit for port, the other using 4-bit for
device and 5-bit for port, configured via the Global 2 Misc register.

Only 4 bits for the source port are needed when interconnecting 88E6xxx
switch devices since they all support less than 16 physical ports. The
full 5 bits are needed when interconnecting a device with 98DXxxx switch
devices since they support more than 16 physical ports.

Add a mv88e6xxx_pvt_setup helper to set the 4-bit port PVT mode, which
will be extended later to also initialize the PVT content.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: fix copyright holder

I do not hold the copyright of the DSA core and drivers source files,
since these changes have been written as an initiative of my day job.
Fix this.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Add mv88e6390 watchdog interrupt support

Implement the ops needed to support the watchdog for the MV88E6390
family.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Add watchdog interrupt handler

The switch contains a watchdog looking for issues with the internal
gubbins of the switch. Hook the interrupt the watchdog triggers and
log the value of the control register indicating why the watchdog
fired. The watchdog can only be cleared with a switch reset, which
will destroy the current configuration. Rather than doing this, just
disable the interrupt.

The mv88e6390 family has different watchdog registers. So use an ops
structure, so support for the mv88e6390 family can be added later.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Pass mii_bus to all PHY operations

In preparation for supporting multiple MDIO busses, pass the mii_bus
structure to all PHY operations. It will in future then be clear on
which MDIO bus the operation should be performed.

For reads/write from phylib, the mii_bus is readily available. However
some internal code also access the PHY, e.g. for EEE and SERDES. Make
this code use the one and only currently available MDIO bus.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: add EEPROM support to 6390

The Marvell 6352 chip has a 8-bit address/16-bit data EEPROM access.
The Marvell 6390 chip has a 16-bit address/8-bit data EEPROM access.

This patch implements the 8-bit data EEPROM access in the mv88e6xxx
driver and adds its support to chips of the 6390 family.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Reserved Management frames to CPU

Older devices have a couple of registers in global2. The mv88e6390
family has a single register in global1 behind which hides similar
configuration. Implement and op for this.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Implement interrupt support.

The switch can have up to two interrupt controllers. One of these
contains the interrupts from the integrated PHYs, so is useful to
export. The Marvell PHY driver can then be used in interrupt mode,
rather than polling, speeding up PHY handling and reducing load on the
MDIO bus.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: make global2 code optional

Since not every chip has a Global2 set of registers, make its support
optional, in which case the related functions will return -EOPNOTSUPP.

This also allows to reduce the size of the mv88e6xxx driver for devices
such as home routers embedding Ethernet chips without Global2 support.

It is present on most recent chips, thus enable its support by default.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: move Global2 code

Marvell chips are composed of multiple SMI devices. One of them at
address 0x1C is called Global2. It provides an extended set of
registers, used for interrupt control, EEPROM access, indirect PHY
access (to bypass the PHY Polling Unit) and cross-chip related setup.

Most chips have it, but some others don't (older ones such as 6060).

Now that its related code is isolated in mv88e6xxx_g2_* functions, move
it to its own global2.c file, making most of its setup code static.
Document each registers in the meantime.

Its compilation can be later avoided for chips without such registers.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>