can: usb: f81604: add Fintek F81604 support

This patch adds support for Fintek USB to 2CAN controller.

Changelog:
v7: https://lore.kernel.org/all/20230509073821.25289-1-peter_hong@fintek.com.tw
1. Fix consistency of coding style for "break" in f81604_register_urbs().
2. Remove goto statement in f81604_open().

v6: https://lore.kernel.org/all/20230505022317.22417-1-peter_hong@fintek.com.tw
1. Remove non-used define and change constant mask to GENMASK().
2. Move some variables declaration from function start to block start.
3. Move some variables initization into declaration.
4. Change variable "id" in f81604_start_xmit() only for CAN ID usage.

v5: https://lore.kernel.org/all/20230420024403.13830-1-peter_hong@fintek.com.tw
1. Change all u8 *buff to struct f81604_int_data/f81604_can_frame.
2. Change all netdev->dev_id to netdev->dev_port.
3. Remove over design for f81604_process_rx_packet(). This device only
report a frame at once, so the f81604_process_rx_packet() are reduced
to process 1 frame.

v4: https://lore.kernel.org/all/20230413084253.1524-1-peter_hong@fintek.com.tw
1. Remove f81604_prepare_urbs/f81604_remove_urbs() and alloc URB/buffer
dynamically in f81604_register_urbs(), using "urbs_anchor" for manage
all rx/int URBs.
2. Add F81604 to MAINTAINERS list.
3. Change handle_clear_reg_work/handle_clear_overrun_work to single
clear_reg_work and using bitwise "clear_flags" to record it.
4. Move __f81604_set_termination in front of f81604_probe() to avoid
rarely racing condition.
5. Add __aligned to struct f81604_int_data / f81604_sff / f81604_eff.
6. Add aligned operations in f81604_start_xmit/f81604_process_rx_packet().
7. Change lots of CANBUS functions first parameter from struct usb_device*
to struct f81604_port_priv *priv. But remain f81604_write / f81604_read
/ f81604_update_bits() as struct usb_device* for
__f81604_set_termination() in probe() stage.
8. Simplify f81604_read_int_callback() and separate into
f81604_handle_tx / f81604_handle_can_bus_errors() functions.

v3: https://lore.kernel.org/all/20230327051048.11589-1-peter_hong@fintek.com.tw
1. Change CAN clock to using MEGA units.
2. Remove USB set/get retry, only remain SJA1000 reset/operation retry.
3. Fix all numberic constant to define.
4. Add terminator control. (only 0 & 120 ohm)
5. Using struct data to represent INT/TX/RX endpoints data instead byte
arrays.
6. Error message reports changed from %d to %pe for mnemotechnic values.
7. Some bit operations are changed to FIELD_PREP().
8. Separate TX functions from f81604_read_int_callback().
9. cf->can_id |= CAN_ERR_CNT in f81604_read_int_callback to report valid
TX/RX error counts.
10. Move f81604_prepare_urbs/f81604_remove_urbs() from CAN open/close() to
USB probe/disconnect().
11. coding style refactoring.

v2: https://lore.kernel.org/all/20230321081152.26510-1-peter_hong@fintek.com.tw
1. coding style refactoring.
2. some const number are defined to describe itself.
3. fix wrong usage for can_get_echo_skb() in f81604_write_bulk_callback().

v1: https://lore.kernel.org/all/20230317093352.3979-1-peter_hong@fintek.com.tw

Signed-off-by: Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230509073821.25289-1-peter_hong@fintek.com.tw
[mkl: add changelog, fix printf format]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can/esd_usb2: Rename esd_usb2.c to esd_usb.c

As suggested by Vincent, renaming of esd_usb2.c to esd_usb.c
and according to that, adaption of Kconfig and Makfile, too.

Link: https://lore.kernel.org/all/20220624190517.2299701-2-frank.jungclaus@esd.eu
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: etas_es58x: add core support for ETAS ES58X CAN USB interfaces

This patch adds the core support for various USB CAN interfaces from
ETAS GmbH (https://www.etas.com/en/products/es58x.php). The next
patches add the glue code drivers for the individual interfaces.

Link: https://lore.kernel.org/r/20210410095948.233305-2-mailhol.vincent@wanadoo.fr
Co-developed-by: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Signed-off-by: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: kvaser_usb: Split driver into kvaser_usb_core.c and kvaser_usb_leaf.c

First part of adding support for Kvaser USB device family "hydra".

Split kvaser_usb.c into kvaser_usb/kvaser_usb{.h,_core.c,_leaf.c}.

kvaser_usb_core.c contains common functionality, such as USB
writing/reading and allocation of netdev.
kvaser_usb_leaf.c contains device specific code, used in
kvaser_usb_core.c.

struct kvaser_usb_dev_ops contains device specific functions that are
common for all devices in the family. While, struct kvaser_usb_dev_cfg
describes the device configurations in terms of CAN clock frequency,
timestamp frequency and CAN controller bittiming constants.

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: ucan: add driver for Theobroma Systems UCAN devices

The UCAN driver supports the microcontroller-based USB/CAN
adapters from Theobroma Systems. There are two form-factors
that run essentially the same firmware:

* Seal: standalone USB stick ( https://www.theobroma-systems.com/seal )

* Mule: integrated on the PCB of various System-on-Modules from
Theobroma Systems like the A31-µQ7 and the RK3399-Q7
( https://www.theobroma-systems.com/rk3399-q7 )

The USB wire protocol has been designed to be as generic and
hardware-indendent as possible in the hope of being useful for
implementation on other microcontrollers.

Signed-off-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: usb: Kconfig/Makefile: sort alphabetically

This patch sorts the entries in the Kconfig and Makefile alphabetically,
so that further contributors can generate patches more easily.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: mcba_usb: Add support for Microchip CAN BUS Analyzer

SocketCAN driver for Microchip CAN BUS Analyzer
(http://www.microchip.com/development-tools/)

Changes in v4:
- possible memory leak fixed in mcba_usb_write_bulk_callback
- LED support added
- failure handling in mcba_usb_probe improved
- C99 initializers for structs on stack

Changes in v3:
- improved/simplified CAN ID conversion
- functions for transmission of skb and cmd separated
- fixed/improved netif_stop_queue handling
- style/cosmetic corrections

Changes in v2:
- Termination handling reimplemented to fit new netlink API
(IFLA_CAN_TERMINATION)
- Bitrate handling reimplemented to fit new netlink API
(IFLA_CAN_BITRATE)
- CAN ID conversion refactored (changed from macro to inline functions)
- CAN DLC handling using get_can_dlc()
- Endianness handling for can_speed introduced
- Debugging removed
- Redundant error prints removed
- Style/cosmetic corrections (i.e. macro names, redefs, inits etc.)

Signed-off-by: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

net: can: use kbuild magic to inherit debug settings

No need to manually copy debug settings into subdir Makefiles. kbuild
has a mechanism for inheriting, so let's use it.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: gs_usb: Added support for the GS_USB CAN devices

The Geschwister Schneider Family of devices are galvanically isolated USB2.0 to
CAN2.0A/B adapters. Currently two form factors are available, a tethered dongle
in a rugged enclosure, and mini-pci-e card.

Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: usb_8dev: Add support for USB2CAN interface from 8 devices

Add device driver for USB2CAN interface from "8 devices" (http://www.8devices.com).

changes since v10:
* small cleanups

changes since v9:
* fixed syslog messages
* fixed crc error number
* increased MAX_RX_URBS and MAX_TX_URBS

changes since v8:
* remove all sysfs files

changes since v7:
* add sysfs documentation
* fix minor styling issue
* fixed can state for passive mode
* changed handling for crc errors

changes since v6:
* changed some variable types to big endian equivalent
* small cleanups

changes since v5:
* unlock mutex on error

changes since v4:
* removed FSF address
* renamed struct usb_8dev
* removed unused variable free_slots
* replaced some _to_cpu functions with pointer equivalent
* fix return value for usb_8dev_set_mode
* handle can errors with separate function
* fix overrun error handling
* rewrite error handling for usb_8dev_start_xmit
* fix urb submit in usb_8dev_start
* various small fixes

Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Bernd Krumboeck <krumboeck@universalnet.at>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: kvaser_usb: Add support for Kvaser CAN/USB devices

This driver provides support for several Kvaser CAN/USB devices.
Such kind of devices supports up to three CAN network interfaces.

It has been tested with a Kvaser USB Leaf Light (one network interface)
connected to a pch_can interface.
The firmware version of the Kvaser device was 2.5.205.

List of Kvaser devices supported by the driver:
- Kvaser Leaf Light
- Kvaser Leaf Professional HS
- Kvaser Leaf SemiPro HS
- Kvaser Leaf Professional LS
- Kvaser Leaf Professional SWC
- Kvaser Leaf Professional LIN
- Kvaser Leaf SemiPro LS
- Kvaser Leaf SemiPro SWC
- Kvaser Memorator II HS/HS
- Kvaser USBcan Professional HS/HS
- Kvaser Leaf Light GI
- Kvaser Leaf Professional HS (OBD-II connector)
- Kvaser Memorator Professional HS/LS
- Kvaser Leaf Light "China"
- Kvaser BlackBird SemiPro
- Kvaser USBcan R

Signed-off-by: Daniel Berglund <db@kvaser.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: usb: PEAK-System Technik USB adapters driver core

This patch adds the core of the peak_usb driver which handles PEAK-System
Technik PCAN USB adapters. It defines the parts which are common to the
PCAN-USB adapters: can network interfaces management, network-to/from-usb
data path interface, timestamps management...

Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: Add driver for esd CAN-USB/2 device

This patch adds a driver for esd's USB high speed
CAN interface. The driver supports devices with
multiple CAN interfaces.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

can: Fix driver Kconfig structure

In 2.6.32-rc the new EMS USB CAN driver was contributed and added the Kconfig
entry right behind an entry of the same *vendor*. This teared the SJA1000
based driver selection into pieces.

This fix cleans up the 2.6.32-rc Kconfig files for the CAN drivers and moves
the SJA1000 and USB Kconfig portions into the belonging directories.

As there are many new CAN drivers in the queue getting this cleanup into
2.6.32-rc would massively reduce the problems for the upcoming drivers.

Thanks,
Oliver

Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface

This patch adds support for one channel CAN/USB interace CPC-USB/ARM7 from
EMS Dr. Thomas Wuensche (http://www.ems-wuensche.com).

Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>