mfd: axp20x: Add support for AXP192

The AXP192 PMIC is similar to the AXP202/AXP209, but with different
regulators, additional GPIOs, and a different IRQ register layout.

Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20230511092609.76183-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>

mfd: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230515182752.10050-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>

mfd: axp20x: Add support for AXP313a PMIC

The AXP313a is a PMIC chip produced by X-Powers, it can be connected via
an I2C bus.
The name AXP1530 seems to appear as well, and this is what is used in
the BSP driver. From all we know it's the same chip, just a different
name. However we have only seen AXP313a chips in the wild, so go with
this name.

Compared to the other AXP PMICs it's a rather simple affair: just three
DCDC converters, three LDOs, and no battery charging support.

Describe the regmap and the MFD bits, along with the registers exposed
via I2C. Aside from the various regulators, also describe the power key
interrupts, and adjust the shutdown handler routine to use a different
register than the other PMICs.
Eventually advertise the device using the new compatible string.

Signed-off-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20230524000012.15028-2-andre.przywara@arm.com
Signed-off-by: Lee Jones <lee@kernel.org>

mfd: axp20x: Add support for AXP15060 PMIC

The AXP15060 is a PMIC chip produced by X-Powers, and could be connected
via an I2C bus.

Describe the regmap and the MFD bits, along with the registers exposed
via I2C. Eventually advertise the device using a new compatible string
and add support for power off the system.

The driver would disable PEK function if IRQ is not configured in device
tree, since some boards (For example, Starfive Visionfive 2) didn't
connect IRQ line of PMIC to SOC.

GPIO function isn't enabled in this commit, since its configuration
operation is different from any existing AXP PMICs and needs
logic modification on existing driver. GPIO support might come in later
patches.

Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/TY3P286MB261162D57695AC8164ED50E298609@TY3P286MB2611.JPNP286.PROD.OUTLOOK.COM

mfd: axp20x-i2c: Convert to i2c's .probe_new()

The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-423-uwe@kleine-koenig.org

i2c: Make remove callback return void

The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)

So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.

Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

mfd/bus: sunxi-rsb: Make .remove() callback return void

The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. To simplify the quest to
make this function return void, let struct sunxi_rsb_driver::remove
return void, too. All users already unconditionally return 0, this
commit makes this obvious and ensures future users don't behave
differently. To simplify even further, make axp20x_device_remove()
return void instead of returning 0 unconditionally, too.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

mfd: axp20x: Skip of_device_id table when !CONFIG_OF

The driver can match either via ACPI or OF. Its of_device_id table is
referenced via of_match_ptr() so it will be unused for !CONFIG_OF
builds:

drivers/mfd/axp20x-i2c.c:60:34: warning: ‘axp20x_i2c_of_match’ defined but not used [-Wunused-const-variable=]

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

mfd: axp20x: Allow the AXP803 to be probed by I2C

The AXP803 can be used both using the RSB proprietary bus, or a more
traditional I2C bus.

Let's add that possibility.

Signed-off-by: Frank Lee <frank@allwinnertech.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

mfd: axp20x-i2c: Do not define 'struct acpi_device_id' when !CONFIG_ACPI

Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI,
struct axp20x_i2c_acpi_match becomes defined by unused.

This squashes the current W=1 kernel builds warning:

drivers/mfd/axp20x-i2c.c:82:36: warning: ‘axp20x_i2c_acpi_match’ defined but not used [-Wunused-const-variable=]

Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Carlo Caione <carlo@caione.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mfd: axp20x: Allow the AXP223 to be probed by I2C

The AXP223 can be used both using the RSB proprietary bus, or a more
traditional I2C bus. The RSB is a faster bus and provides more features
(like some integrity checks on the messages), so it's usually preferrable
to use it, but since it's proprietary, when we want to use the PMIC in a
multi-master setup, the i2c might make sense as well.

Let's add that possibility.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

mfd: axp20x: Support AXP806 in I2C mode

The Pine64 H64 board uses an AXP806 PMIC in I2C and self-working mode.
The H64 SoC does not have the usual RSB controller.

This patch adds AXP806 to the list of devices supported in I2C mode.
In theory, all RSB-based PMICs can also be used in I2C mode.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

mfd: axp20x-i2c: Add i2c-ids to fix module auto-loading

The i2c subsys does not load modules by compatible, only by
i2c-id, with e.g. a modalias of: "i2c:axp209".

Populate the axp20x_i2c_id[] table with supported ids, so that
module auto-loading will work.

Reported-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

mfd: axp20x: Split the driver into core and i2c bits

The axp20x driver assumes the device is i2c based. This is not the
case with later chips, which use a proprietary 2 wire serial bus
by Allwinner called "Reduced Serial Bus".

This patch follows the example of mfd/wm831x and splits it into
an interface independent core, and an i2c specific glue layer.
MFD_AXP20X and the new MFD_AXP20X_I2C are changed to tristate
symbols, allowing the driver to be built as modules.

Whitespace and other style errors in the moved i2c specific code
have been fixed. Included but unused header files are removed as
well.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>