media: rc: bpf attach/detach requires write permission

Note that bpf attach/detach also requires CAP_NET_ADMIN.

Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rc-core: rename ir_raw_event_reset to ir_raw_event_overflow

The driver report a reset event when the hardware reports and overflow.
There is no reason to have a generic "reset" event.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rc: rename ir_lirc_* functions to lirc_*

Remove pointless ir_ prefix.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rc: harmonize infrared durations to microseconds

rc-core kapi uses nanoseconds for infrared durations for receiving, and
microseconds for sending. The uapi already uses microseconds for both,
so this patch does not change the uapi.

Infrared durations do not need nanosecond resolution. IR protocols do not
have durations shorter than about 100 microseconds. Some IR hardware offers
250 microseconds resolution, which is sufficient for most protocols.
Better hardware has 50 microsecond resolution and is enough for every
protocol I am aware off.

Unify on microseconds everywhere. This simplifies the code since less
conversion between microseconds and nanoseconds needs to be done.

This affects:
- rx_resolution member of struct rc_dev
- timeout member of struct rc_dev
- duration member in struct ir_raw_event

Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Patrick Lerda <patrick9876@free.fr>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Benjamin Valentin <benpicco@googlemail.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rc: no need for decoder state if decoder not enabled

One struct ir_raw_event_ctrl is allocated per raw IR device; reduce the
amount allocated if not all decoders are enabled.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rc: Use the correct style for SPDX License Identifier

This patch corrects the SPDX License Identifier style
in header file related to Remote Controller Driver for Linux.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: rcmm decoder and encoder

media: add support for RCMM infrared remote controls.

Signed-off-by: Patrick Lerda <patrick9876@free.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: mce_kbd: input events via rc-core's input device

There is no need to create another input device.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: imon: report mouse events using rc-core's input device

There is no need to create another input device.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: Remove init_ir_raw_event and DEFINE_IR_RAW_EVENT macros

This can be done with c99 initializers, which makes the code cleaner
and more transparent. It does require gcc 4.6, because of this bug
in earlier versions:

https://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676

Since commit cafa0010cd51 ("Raise the minimum required gcc version to
4.6"), this is the case.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: introduce BPF_PROG_LIRC_MODE2

Add support for BPF_PROG_LIRC_MODE2. This type of BPF program can call
rc_keydown() to reported decoded IR scancodes, or rc_repeat() to report
that the last key should be repeated.

The bpf program can be attached to using the bpf(BPF_PROG_ATTACH) syscall;
the target_fd must be the /dev/lircN device.

Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

media: rc: imon decoder: support the stick

The iMON PAD controller has a analog stick, which can be switched to
keyboard mode (cursor keys) or work as a crappy mouse.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: mce_kbd decoder: fix race condition

The MCE keyboard sends both key down and key up events. We have a timeout
handler mce_kbd_rx_timeout() in case the keyup event is never received;
however, this may race with new key down events from occurring.

The race is that key down scancode arrives and key down events are
generated. The timeout handler races this and generates key up events
straight afterwards. Since the keyboard generates scancodes every 100ms,
most likely the keys will be repeated 100ms later, and now we have new
key down events and the user sees duplicate key presses.

Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc: set timeout to smallest value required by enabled protocols

The longer the IR timeout, the longer the rc device waits until delivering
the trailing space. So, by reducing this timeout, we reduce the delay for
the last scancode to be delivered.

Note that the lirc daemon disables all protocols, in which case we revert
back to the default value.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc: add new imon protocol decoder and encoder

This makes it possible to use the various iMON remotes with any raw IR
RC device.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc: fix race condition in ir_raw_event_store_edge() handling

There is a possible race condition between the IR timeout being generated
from the timer, and new IR arriving. This could result in the timeout
being added to the kfifo after new IR arrives. On top of that, there is
concurrent write access to the kfifo from ir_raw_event_store_edge() and
the timer.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc: remove obsolete comment

This comment is no longer relevant.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc: clean up leader pulse/space for manchester encoding

The IR rc6 encoder sends the header using manchester encoding using 0
bits, which causes the following:

UBSAN: Undefined behaviour in drivers/media/rc/rc-ir-raw.c:247:6
shift exponent 4294967295 is too large for 64-bit type 'long long unsigned int'

So, allow the leader code to send a pulse and space and remove the unused
pulse_space_start field.

Cc: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: fix SPDX comment on some header files

The agreed format is to use /* */ comments inside header
files. Unfortunately, I ended by using // on a few ones.

Reported-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc: move ir-lirc-codec.c contents into lirc_dev.c

Since removing the lirc kapi, ir-lirc-codec.c only contains lirc fops
so the file name is no longer correct. By moving its content into
lirc_dev.c the ugly extern struct lirc_fops is not longer needed,
and everything lirc related is in one file.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: lirc: implement reading scancode

This implements LIRC_MODE_SCANCODE reading from the lirc device. The
scancode can be read from the input device too, but with this interface
you get the rc protocol, keycode, toggle and repeat status in addition
to just the scancode.

int main()
{
int fd, mode, rc;
fd = open("/dev/lirc0", O_RDWR);

mode = LIRC_MODE_SCANCODE;
if (ioctl(fd, LIRC_SET_REC_MODE, &mode)) {
// kernel too old or lirc does not support transmit
}
struct lirc_scancode scancode;
while (read(fd, &scancode, sizeof(scancode)) == sizeof(scancode)) {
printf("protocol:%d scancode:0x%x toggle:%d repeat:%d\n",
scancode.rc_proto, scancode.scancode,
!!(scancode.flags & LIRC_SCANCODE_FLAG_TOGGLE),
!!(scancode.flags & LIRC_SCANCODE_FLAG_REPEAT));
}
close(fd);
}

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: lirc: remove last remnants of lirc kapi

rc-core has replaced the lirc kapi many years ago, and now with the last
driver ported to rc-core, we can finally remove it.

Note this has no effect on userspace.

All future IR drivers should use the rc-core api.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: lirc: validate scancode for transmit

Ensure we reject an attempt to transmit invalid scancodes.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: lirc: lirc interface should not be a raw decoder

The lirc user interface exists as a raw decoder, which does not make
much sense for transmit-only devices.

In addition, we want to have lirc char devices for devices which do not
use raw IR, i.e. scancode only devices.

Note that rc-code, lirc_dev, ir-lirc-codec are now calling functions of
each other, so they've been merged into one module rc-core to avoid
circular dependencies.

Since ir-lirc-codec no longer exists as separate codec module, there is no
need for RC_DRIVER_IR_RAW_TX type drivers to call ir_raw_event_register().

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc: auto load encoder if necessary

When sending scancodes, load the encoder if we need it.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: lirc: use the correct carrier for scancode transmit

If the lirc device supports it, set the carrier for the protocol.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: lirc: implement scancode sending

This introduces a new lirc mode: scancode. Any device which can send raw IR
can now also send scancodes.

int main()
{
int mode, fd = open("/dev/lirc0", O_RDWR);

mode = LIRC_MODE_SCANCODE;
if (ioctl(fd, LIRC_SET_SEND_MODE, &mode)) {
// kernel too old or lirc does not support transmit
}
struct lirc_scancode scancode = {
.scancode = 0x1e3d,
.rc_proto = RC_PROTO_RC5,
};
write(fd, &scancode, sizeof(scancode));
close(fd);
}

The other fields of lirc_scancode must be set to 0.

Note that toggle (rc5, rc6) and repeats (nec) are not implemented. Nor is
there a method for holding down a key for a period.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc: add SPDX identifiers to the code I wrote

As we're now using SPDX identifiers, on the several
media drivers I wrote, add the proper SPDX, identifying
the license I meant.

As we're now using the short license, it doesn't make sense to
keep the original license text.

Also, fix MODULE_LICENSE to properly identify GPL v2.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] media: rename struct lirc_driver to struct lirc_dev

This is in preparation for the later patches which do away with
struct irctl entirely.

Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

media: rc: rename RC_TYPE_* to RC_PROTO_* and RC_BIT_* to RC_PROTO_BIT_*

RC_TYPE is confusing and it's just the protocol. So rename it.

Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc: simplify ir_raw_event_store_edge()

Since commit 12749b198fa4 ("[media] rc: saa7134: add trailing space for
timely decoding"), the workaround of inserting reset events is no
longer needed.

Note that the initial reset is not needed either; other rc-core drivers
that don't use ir_raw_event_store_edge() never call this at all.

Verified on a HVR-1150 and Raspberry Pi.

Fixes: 3f5c4c73322e ("[media] rc: fix ghost keypresses with certain hw")

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc-core: improve ir_raw_store_edge() handling

The gpio-ir-recv driver does many wakeups (once per edge); the saa7134
driver has special handling to only wakeup 15ms after the first edge.
Make this part of rc-core so gpio-ir-recv also benefits from
this (so a rc-5 keypress now causes 3 wakeups rather than 24).

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] rc-core: cleanup rc_register_device

The device core infrastructure is based on the presumption that
once a driver calls device_add(), it must be ready to accept
userspace interaction.

This requires splitting rc_setup_rx_device() into two functions
and reorganizing rc_register_device() so that as much work
as possible is performed before calling device_add().

Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] mce_kbd: add encoder

Split the protocol into two variants, one for keyboard and one for mouse
data.

Note that the mce_kbd protocol cannot be used on the igorplugusb, since
the IR is too long.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] rc: ir-sony-decoder: Add encode capability

Add the capability to encode Sony scancodes as raw events. Sony uses
pulse length rather than pulse distance.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] rc: rc-ir-raw: Add pulse-distance modulation helper

Add IR encoding helper for pulse-distance modulation as used by the NEC
protocol.

Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] rc: rc-ir-raw: Add Manchester encoder (phase encoder) helper

Adding a simple Manchester encoder to rc-core.
Manchester coding is used by at least RC-5 and RC-6 protocols and their
variants.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] rc: rc-ir-raw: Add scancode encoder callback

Add a callback to raw ir handlers for encoding and modulating a scancode
to a set of raw events. This could be used for transmit, or for
converting a wakeup scancode to a form that is more suitable for raw
hardware wake up filters.

Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] rc: refactor raw handler kthread

I think we can get rid of the spinlock protecting the kthread from being
interrupted by a wakeup in certain parts.
Even with the current implementation of the kthread the only lost wakeup
scenario could happen if the wakeup occurs between the kfifo_len check
and setting the state to TASK_INTERRUPTIBLE.

In the changed version we could lose a wakeup if it occurs between
processing the fifo content and setting the state to TASK_INTERRUPTIBLE.
This scenario is covered by an additional check for available events in
the fifo and setting the state to TASK_RUNNING in this case.

In addition the changed version flushes the kfifo before ending
when the kthread is stopped.

With this patch we gain:
- Get rid of the spinlock
- Simplify code
- Don't grep / release the mutex for each individual event but just once
for the complete fifo content. This reduces overhead if a driver e.g.
triggers processing after writing the content of a hw fifo to the kfifo.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] media: rc: raw: improve FIFO handling

The FIFO is used for ir_raw_event records, however for some historic
reason the FIFO is used on a per byte basis. IMHO this adds unneeded
complexity. Therefore set up the FIFO for ir_raw_event records.

This also allows to define the FIFO statically as part of
ir_raw_event_ctrl instead of having to allocate the FIFO dynamically.
In addition:

- When writing into the FIFO and it's full return ENOSPC instead of
ENOMEM thus making it easier to tell between "FIFO full" and
"Dynamic memory allocation failed" when the error is propagated to
a higher level.
Also add an error message.

- When reading from the FIFO check whether it's empty.
This is not strictly needed here but kfifo_out is annotated
"must check" anyway.

Successfully tested it with the nuvoton-cir driver.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: rc: remove unneeded code

Now that that the decoder modules are loaded on-demand we can move
loading the lirc module to rc_register_device directly and remove
unneeded functions and comments.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

[media] media: rc: load decoder modules on-demand

Remove code for unconditional decoder module loading (except lirc).

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Revert "[media] rc: rc-ir-raw: Add scancode encoder callback"

This reverts commit 9869da5bacc5c9b865a183bd36c04be76cdd325d.

The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.

Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Revert "[media] rc: rc-ir-raw: Add Manchester encoder (phase encoder) helper"

This reverts commit 1d971d927efa2e10194c96ed0475b6d6054342d8.

The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.

Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Revert "[media] rc: rc-core: Add support for encode_wakeup drivers"

This reverts commit 0d830b2d1295fee82546d57185da5a6604f11ae2.

The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.

Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] rc: rc-core: Add support for encode_wakeup drivers

Add support in rc-core for drivers which implement the wakeup scancode
filter by encoding the scancode using the raw IR encoders. This is by
way of rc_dev::encode_wakeup which should be set to true to make the
allowed wakeup protocols the same as the set of raw IR encoders.

As well as updating the sysfs interface to know which wakeup protocols
are allowed for encode_wakeup drivers, also ensure that the IR
decoders/encoders are loaded when an encode_wakeup driver is registered.

Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] rc: rc-ir-raw: Add Manchester encoder (phase encoder) helper

Adding a simple Manchester encoder to rc-core.
Manchester coding is used by at least RC-5 and RC-6 protocols and their
variants.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] rc: rc-ir-raw: Add scancode encoder callback

Add a callback to raw ir handlers for encoding and modulating a scancode
to a set of raw events. This could be used for transmit, or for
converting a wakeup scancode filter to a form that is more suitable for
raw hardware wake up filters.

Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] rc: Add support for decoding XMP protocol

This protocol is found on Dreambox remotes

[m.chehab@samsung.com: CodingStyle fixes and conflict fix]
Signed-off-by: Marcel Mol <marcel@mesa.nl>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

[media] rc-core: merge rc5 and streamzap decoders

Now that the protocol is part of the scancode, it is pretty easy to merge
the rc5 and streamzap decoders. An additional advantage is that the decoder
is now stricter as it waits for the trailing silence before determining that
a command is a valid rc5/streamzap command (which avoids collisions that I've
seen with e.g. Sony protocols).

Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

[media, edac] Change my email address

There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

[media] rc: ir-raw: Load ir-sharp-decoder module at init

Commit 1d184b0bc13d ([media] media: rc: add raw decoder for Sharp
protocol) added a new raw IR decoder for the sharp protocol, but didn't
add the code to load the module at init as is done for other raw
decoders, so add that code now.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

[media] media: rc: add raw decoder for Sharp protocol

Add a raw decoder for the Sharp protocol. It uses a pulse distance
modulation with a pulse of 320us and a bit period of 2ms for a logical 1
and 1ms for a logical 0. The first part of the message consists of a
5-bit address, an 8-bit command, and two other bits, followed by a 40ms
gap before the echo message which is an inverted version of the main
message except for the address bits.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

[media] rc-core: don't treat dev->rc_map.rc_type as a bitmap

store_protocols() treats dev->rc_map.rc_type as a bitmap which is wrong for
two reasons. First of all, it is pretty bogus to change the protocol type of
the keymap just because the hardware has been asked to decode a different
protocol.
Second, dev->rc_map.rc_type is an enum (i.e. a single protocol) as pointed
out by James Hogan <james.hogan@imgtec.com>.
Fix both issues by introducing a separate enabled_protocols member to
struct rc_dev.

Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media/rc: fix oops on unloading module rc-core

During modiles initialization rc-core schedules work which calls
request_module() several times to load ir-*-decoder modules, but
it does not wait or cancel this work on module unloading.
rc-core should use request_module_nowait() instead, because it
anyway cannot load modules synchronously or cancel/wait pending
work on unloading, because this leads to deadlock on modules_mutex
between several "modprobe" processes.

Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc/ir-raw: use kfifo_rec_ptr_1 instead of kfifo

Raw IR events are passed to the raw event thread through a kfifo. The
size of the event struct is 12 bytes, and space for 512 events is
reserved in the kfifo (6144 bytes), however this is rounded down to 4096
bytes (the next power of 2) by __kfifo_alloc().

4096 bytes is not divisible by 12 therefore if the fifo fills up a third
of a record will be written in the end of the kfifo by
ir_raw_event_store() because the recsize of the fifo is 0 (it doesn't
have records). When this is read by ir_raw_event_thread() a corrupted or
partial record will be read, and in the case of a partial record the
BUG_ON(retval != sizeof(ev)) gets hit too.

According to samples/kfifo/record-example.c struct kfifo_rec_ptr_1 can
handle records of a length between 0 and 255 bytes, so change struct
ir_raw_event_ctrl to use that instead of struct kfifo.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc: Add support for decoding Sanyo protocol

This protocol is found on Sanyo/Aiwa remotes.

Tested with an Aiwa RC-7AS06 remote control.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media, rc: Use static inline functions to kill warnings

This patch converts some ifdef'd wrapper functions from macros to static inline
functions to kill the following warnings issued by GCC:

CC [M] drivers/media/rc/ir-raw.o
drivers/media/rc/ir-raw.c: In function ‘init_decoders’:
drivers/media/rc/ir-raw.c:353:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:354:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:355:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:356:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:357:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:359:2: warning: statement with no effect [-Wunused-value]

Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc-core support for Microsoft IR keyboard/mouse

This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.

Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.

Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.

This work is inspired by lirc_mod_mce:

The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.

Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.

callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...

CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc-core: fix some leftovers from the renaming patches

Fix some minor comments etc which are leftover from the old naming scheme.

Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc: rename the remaining things to rc_core

The Remote Controller subsystem is meant to be used not only by Infra Red
but also for similar types of Remote Controllers. The core is not specific
to Infra Red. As such, rename:
- ir-core.h to rc-core.h
- IR_CORE to RC_CORE
- namespace inside rc-core.c/rc-core.h

To be consistent with the other changes.

No functional change on this patch.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ir-core: make struct rc_dev the primary interface

This patch merges the ir_input_dev and ir_dev_props structs into a single
struct called rc_dev. The drivers and various functions in rc-core used
by the drivers are also changed to use rc_dev as the primary interface
when dealing with rc-core.

This means that the input_dev is abstracted away from the drivers which
is necessary if we ever want to support multiple input devs per rc device.

The new API is similar to what the input subsystem uses, i.e:
rc_device_alloc()
rc_device_free()
rc_device_register()
rc_device_unregister()

[mchehab@redhat.com: Fix compilation on mceusb and cx231xx, due to merge conflicts]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc-core: Code cleanup after merging rc-sysfs and rc-map into rc-main

[mchehab@redhat.com: this patch were originally bundled with some renaming
stuff and with the file merges, as seen at:
https://patchwork.kernel.org/patch/291092/.

Instead of using the original approach, I wrote the rename patches and the
code merge as separate changes, then applied the difference on this patch.
This way, it is easier to see the real changes at the code, and will be easier
to merge upstream, especially if some conflict rises on the renaming patches]

Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Rename rc-core files from ir- to rc-

As protocol decoders are specific to InfraRed, keep their names as-is.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>