media: rc: gpio-ir-recv: drop of_match_ptr for ID table

The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:

drivers/media/rc/gpio-ir-recv.c:197:34: error: ‘gpio_ir_recv_of_match’ defined but not used [-Werror=unused-const-variable=]

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sean Young <sean@mess.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rc: gpio-ir-recv: Fix support for wake-up

The driver was intended from the start to be a wake-up source for the
system, however due to the absence of a suitable call to
device_set_wakeup_capable(), the device_may_wakeup() call used to decide
whether to enable the GPIO interrupt as a wake-up source would never
happen. Lookup the DT standard "wakeup-source" property and call
device_init_wakeup() to ensure the device is flagged as being wakeup
capable.

Reported-by: Matthew Lear <matthew.lear@broadcom.com>
Fixes: fd0f6851eb46 ("[media] rc: Add support for GPIO based IR Receiver driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

media: gpio-ir-recv: Convert to platform remove callback returning void

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

media: rc: gpio-ir-recv: add remove function

In case runtime PM is enabled, do runtime PM clean up to remove
cpu latency qos request, otherwise driver removal may have below
kernel dump:

[ 19.463299] Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000048
[ 19.472161] Mem abort info:
[ 19.474985] ESR = 0x0000000096000004
[ 19.478754] EC = 0x25: DABT (current EL), IL = 32 bits
[ 19.484081] SET = 0, FnV = 0
[ 19.487149] EA = 0, S1PTW = 0
[ 19.490361] FSC = 0x04: level 0 translation fault
[ 19.495256] Data abort info:
[ 19.498149] ISV = 0, ISS = 0x00000004
[ 19.501997] CM = 0, WnR = 0
[ 19.504977] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000049f81000
[ 19.511432] [0000000000000048] pgd=0000000000000000,
p4d=0000000000000000
[ 19.518245] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 19.524520] Modules linked in: gpio_ir_recv(+) rc_core [last
unloaded: rc_core]
[ 19.531845] CPU: 0 PID: 445 Comm: insmod Not tainted
6.2.0-rc1-00028-g2c397a46d47c #72
[ 19.531854] Hardware name: FSL i.MX8MM EVK board (DT)
[ 19.531859] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS
BTYPE=--)
[ 19.551777] pc : cpu_latency_qos_remove_request+0x20/0x110
[ 19.557277] lr : gpio_ir_recv_runtime_suspend+0x18/0x30
[gpio_ir_recv]
[ 19.557294] sp : ffff800008ce3740
[ 19.557297] x29: ffff800008ce3740 x28: 0000000000000000 x27:
ffff800008ce3d50
[ 19.574270] x26: ffffc7e3e9cea100 x25: 00000000000f4240 x24:
ffffc7e3f9ef0e30
[ 19.574284] x23: 0000000000000000 x22: ffff0061803820f4 x21:
0000000000000008
[ 19.574296] x20: ffffc7e3fa75df30 x19: 0000000000000020 x18:
ffffffffffffffff
[ 19.588570] x17: 0000000000000000 x16: ffffc7e3f9efab70 x15:
ffffffffffffffff
[ 19.595712] x14: ffff800008ce37b8 x13: ffff800008ce37aa x12:
0000000000000001
[ 19.602853] x11: 0000000000000001 x10: ffffcbe3ec0dff87 x9 :
0000000000000008
[ 19.609991] x8 : 0101010101010101 x7 : 0000000000000000 x6 :
000000000f0bfe9f
[ 19.624261] x5 : 00ffffffffffffff x4 : 0025ab8e00000000 x3 :
ffff006180382010
[ 19.631405] x2 : ffffc7e3e9ce8030 x1 : ffffc7e3fc3eb810 x0 :
0000000000000020
[ 19.638548] Call trace:
[ 19.640995] cpu_latency_qos_remove_request+0x20/0x110
[ 19.646142] gpio_ir_recv_runtime_suspend+0x18/0x30 [gpio_ir_recv]
[ 19.652339] pm_generic_runtime_suspend+0x2c/0x44
[ 19.657055] __rpm_callback+0x48/0x1dc
[ 19.660807] rpm_callback+0x6c/0x80
[ 19.664301] rpm_suspend+0x10c/0x640
[ 19.667880] rpm_idle+0x250/0x2d0
[ 19.671198] update_autosuspend+0x38/0xe0
[ 19.675213] pm_runtime_set_autosuspend_delay+0x40/0x60
[ 19.680442] gpio_ir_recv_probe+0x1b4/0x21c [gpio_ir_recv]
[ 19.685941] platform_probe+0x68/0xc0
[ 19.689610] really_probe+0xc0/0x3dc
[ 19.693189] __driver_probe_device+0x7c/0x190
[ 19.697550] driver_probe_device+0x3c/0x110
[ 19.701739] __driver_attach+0xf4/0x200
[ 19.705578] bus_for_each_dev+0x70/0xd0
[ 19.709417] driver_attach+0x24/0x30
[ 19.712998] bus_add_driver+0x17c/0x240
[ 19.716834] driver_register+0x78/0x130
[ 19.720676] __platform_driver_register+0x28/0x34
[ 19.725386] gpio_ir_recv_driver_init+0x20/0x1000 [gpio_ir_recv]
[ 19.731404] do_one_initcall+0x44/0x2ac
[ 19.735243] do_init_module+0x48/0x1d0
[ 19.739003] load_module+0x19fc/0x2034
[ 19.742759] __do_sys_finit_module+0xac/0x12c
[ 19.747124] __arm64_sys_finit_module+0x20/0x30
[ 19.751664] invoke_syscall+0x48/0x114
[ 19.755420] el0_svc_common.constprop.0+0xcc/0xec
[ 19.760132] do_el0_svc+0x38/0xb0
[ 19.763456] el0_svc+0x2c/0x84
[ 19.766516] el0t_64_sync_handler+0xf4/0x120
[ 19.770789] el0t_64_sync+0x190/0x194
[ 19.774460] Code: 910003fd a90153f3 aa0003f3 91204021 (f9401400)
[ 19.780556] ---[ end trace 0000000000000000 ]---

Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: Switch to use dev_err_probe() helper

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER.

Reviewed-by: Sean Young <sean@mess.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

media: rc: gpio-ir-recv: add QoS support for cpuidle system

GPIO IR receive is much rely on interrupt response, uneven interrupt
latency will lead to incorrect timing, so the decoder fails to decode
it. The issue is particularly acute on some systems which support
cpuidle, not all, dynamically disable and enable cpuidle can solve this
problem to a great extent.

However, there is a downside to this approach, the measurement of header
on the first frame may incorrect. Test on i.MX8M serials, when enable
cpuidle, interrupt latency could be about 500us.

With this patch:
1. has no side effect on non-cpuidle system, even runtime pm api won't
be invoked to avoid a bunch of pm busy work for devices that do not need
it, including spinlocks, ktime, etc.
2. latency is still much longer for the first gpio interrupt on cpuidle
system, so the first frame may not be decoded. Generally, RC would transmit
multiple frames at once press, we can sacrifice the first frame.
3. add "linux,autosuspend-period" property in device tree if you also
suffer this cpuidle issue.

Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 284

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 294 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[media] media: rc: fix gpio-ir-receiver build failure

The 0-day robot reports:

drivers/media/rc/gpio-ir-recv.c: In function 'gpio_ir_recv_irq':
>> drivers/media/rc/gpio-ir-recv.c:38:8: error: implicit declaration of function 'gpiod_get_value' [-Werror=implicit-function-declaration]

Fixes: eed008e605d1 ("[media] media: rc: gpio-ir-recv: use gpiolib API")

For some reason only partial patch was applied. Also include
gpio/consumer.h otherwise compile test fails.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Sean Young <sean@mess.org>

[media] media: rc: gpio-ir-recv: use gpiolib API

Gpiolib API is preferred way to access gpios.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: rc: gpio-ir-recv: remove gpio_ir_recv_platform_data

gpio_ir_recv_platform_data are not used anywhere in kernel tree,
so remove it.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: rc: gpio-ir-recv: use KBUILD_MODNAME

There already is standard macro providing driver name, use it.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: rc: gpio-ir-recv: use devm_request_irq

Use of devm_request_irq simplifies error unwinding and as
free_irq was the last user of driver remove function,
remove it too.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: rc: gpio-ir-recv: do not allow threaded interrupt handler

Requesting any context irq is not actually great idea since threaded
interrupt handler is run at too unpredictable time which turns
timing information wrong. Fix it by requesting regular interrupt.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: rc: gpio-ir-recv: use devm_rc_register_device

Use of devm_rc_register_device simplifies error unwinding.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: rc: gpio-ir-recv: use devm_gpio_request_one

Use of devm_gpio_request_one simplifies error unwinding.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: rc: gpio-ir-recv: use devm_rc_allocate_device

Use of devm_rc_allocate_device simplifies error unwinding.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: rc: gpio-ir-recv: use devm_kzalloc

Use of devm_kzalloc simplifies error unwinding.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: rc: gpio-ir-recv: use helper variable to access device info

Using explicit struct device variable makes code a bit more readable.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

media: rc: rename RC_TYPE_* to RC_PROTO_* and RC_BIT_* to RC_PROTO_BIT_*

RC_TYPE is confusing and it's just the protocol. So rename it.

Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc: simplify ir_raw_event_store_edge()

Since commit 12749b198fa4 ("[media] rc: saa7134: add trailing space for
timely decoding"), the workaround of inserting reset events is no
longer needed.

Note that the initial reset is not needed either; other rc-core drivers
that don't use ir_raw_event_store_edge() never call this at all.

Verified on a HVR-1150 and Raspberry Pi.

Fixes: 3f5c4c73322e ("[media] rc: fix ghost keypresses with certain hw")

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc: saa7134: add trailing space for timely decoding

The gpio-ir-recv driver adds timeouts which the saa7134 lacks; this
causes keypress not to arrive, and to only arrive once more IR is
received. This is what the commit below calls "ghost keypresses",
and that commit does not solve the issue completely.

This makes the IR on the HVR-1150 much more reliable and responsive.

Fixes: 3f5c4c73322e ("[media] rc: fix ghost keypresses with certain hw")

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: rc-core: rename input_name to device_name

When an ir-spi is registered, you get this message.

rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0

"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.

Also make driver_name const char* so that no casts are needed anywhere.

Now ir-spi reports:

rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] gpio-ir: do not allow a timeout of 0

According to the documentation, a timeout of 0 turns off timeouts,
which is not the case.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] rc-main: assign driver type during allocation

The driver type can be assigned immediately when an RC device
requests to the framework to allocate the device.

This is an 'enum rc_driver_type' data type and specifies whether
the device is a raw receiver or scancode receiver. The type will
be given as parameter to the rc_allocate_device device.

Change accordingly all the drivers calling rc_allocate_device()
so that the device type is specified during the rc device
allocation. Whenever the device type is not specified, it will be
set as RC_DRIVER_SCANCODE which was the default '0' value.

Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] rc: raw IR drivers cannot handle cec, unknown or other

unknown and other are for IR protocols for which we have no decoder,
so the raw IR drivers have no chance of generating them. cec is not
an IR protocol.

Signed-off-by: Sean Young <sean@mess.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] rc: gpio-ir-recv: add timeout on idle

Many decoders require a trailing space (period without IR illumination)
to be delivered before completing a decode.

Since the gpio-ir-recv driver only delivers events on gpio transitions,
a single IR symbol (caused by a quick touch on an IR remote) will not
be properly decoded without the use of a timer to flush the tail end
state of the IR receiver.

This patch initializes and uses a timer and the timeout field of rcdev
to complete the stream and allow decode.

The timeout can be overridden through the use of the LIRC_SET_REC_TIMEOUT
ioctl.

Signed-off-by: Eric Nelson <eric@nelint.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] include/media: move platform_data to linux/platform_data/media

Let's not mix platform_data headers with the core headers. Instead, let's
create a subdir at linux/platform_data and move the headers to that
common place, adding it to MAINTAINERS.

The headers were moved with:
mkdir include/linux/platform_data/media/; git mv include/media/gpio-ir-recv.h include/media/ir-rx51.h include/media/mmp-camera.h include/media/omap1_camera.h include/media/omap4iss.h include/media/s5p_hdmi.h include/media/si4713.h include/media/sii9234.h include/media/smiapp.h include/media/soc_camera.h include/media/soc_camera_platform.h include/media/timb_radio.h include/media/timb_video.h include/linux/platform_data/media/

And the references fixed with this script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="media/"
DIRS="media/"

echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

[media] rc: gpio-ir-recv: don't sleep in irq handler

Don't allow sleep when getting the gpio value in the irq-handler.
On my rk3288 board this results in might_sleep warnings when receiving
data like:

BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1531
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/0
CPU: 0 PID: 0 Comm: swapper/0 Tainted: P 4.1.0-rc5+ #2011
Hardware name: Rockchip (Device Tree)
[<c00189a0>] (unwind_backtrace) from [<c0013b04>] (show_stack+0x20/0x24)
[<c0013b04>] (show_stack) from [<c0757970>] (dump_stack+0x8c/0xbc)
[<c0757970>] (dump_stack) from [<c0053188>] (___might_sleep+0x238/0x284)
[<c0053188>] (___might_sleep) from [<c0053264>] (__might_sleep+0x90/0xa4)
[<c0053264>] (__might_sleep) from [<c02ff4ac>] (gpiod_get_raw_value_cansleep+0x28/0x44)
[<c02ff4ac>] (gpiod_get_raw_value_cansleep) from [<bf0363c4>] (gpio_ir_recv_irq+0x24/0x6c [gpio_ir_recv])
[<bf0363c4>] (gpio_ir_recv_irq [gpio_ir_recv]) from [<c008a78c>] (handle_irq_event_percpu+0x164/0x550)
[<c008a78c>] (handle_irq_event_percpu) from [<c008abc4>] (handle_irq_event+0x4c/0x6c)
[<c008abc4>] (handle_irq_event) from [<c008df88>] (handle_edge_irq+0x128/0x150)
[<c008df88>] (handle_edge_irq) from [<c0089edc>] (generic_handle_irq+0x30/0x40)
[<c0089edc>] (generic_handle_irq) from [<c02fc4cc>] (rockchip_irq_demux+0x158/0x210)
[<c02fc4cc>] (rockchip_irq_demux) from [<c0089edc>] (generic_handle_irq+0x30/0x40)
[<c0089edc>] (generic_handle_irq) from [<c008a058>] (__handle_domain_irq+0x98/0xc0)
[<c008a058>] (__handle_domain_irq) from [<c00094a4>] (gic_handle_irq+0x4c/0x70)
[<c00094a4>] (gic_handle_irq) from [<c0014684>] (__irq_svc+0x44/0x5c)

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] constify of_device_id array

of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)

[mchehab@osg.samsung.com: fix a merge conflict at adv7604.c]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

media: rc: drop owner assignment from platform_drivers

A platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

[media] rc-core: remove protocol arrays

The basic API of rc-core used to be:

dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();

which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:

dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();

There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).

[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

[media] rc: abstract access to allowed/enabled protocols

The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

[media] gpio-ir-recv: Include linux/of.h header

'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

[media] rc: gpio-ir-recv: Remove redundant platform_set_drvdata()

Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: rc: gpio-ir-recv: add support for device tree parsing

This patch adds device tree parsing for gpio_ir_recv platform_data and
the mandatory binding documentation. It basically follows what we already
have for e.g. gpio_keys. All required device tree properties are OS
independent but an optional property allows linux specific support for rc
maps.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Drivers: media: remove __dev* attributes.

CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[media] rc: Fix double free in gpio_ir_recv_remove()

Since rc_unregister_device() frees its argument there's no need to
subsequently call rc_free_device() on the same variable - in fact it's
a double free bug.
Easily fixed by just removing the rc_free_device() call.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc: Fix double free in gpio_ir_recv_probe()

At the 'err_request_irq' label, rc_unregister_device(rcdev) frees its
argument. So when we fall through to the 'err_gpio_request' label
further down and call rc_free_device(rcdev) then that's a double free.
Fix that by moving 'rcdev = NULL' from after the call to
rc_free_device() to after rc_unregister_device(). That fixes the
problem since rc_free_device() just does nothing if passed NULL and
there's no further use of 'rcdev' after the call to rc_free_device()
so it's not needed there.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc-core: add separate defines for protocol bitmaps and numbers

The RC_TYPE_* defines are currently used both where a single protocol is
expected and where a bitmap of protocols is expected.

Functions like rc_keydown() and functions which add/remove entries to the
keytable want a single protocol. Future userspace APIs would also
benefit from numeric protocols (rather than bitmap ones). Keytables are
smaller if they can use a small(ish) integer rather than a bitmap.

Other functions or struct members (e.g. allowed_protos,
enabled_protocols, etc) accept multiple protocols and need a bitmap.

Using different types reduces the risk of programmer error. Using a
protocol enum whereever possible also makes for a more future-proof
user-space API as we don't need to worry about a sufficient number of
bits being available (e.g. in structs used for ioctl() calls).

The use of both a number and a corresponding bit is dalso one in e.g.
the input subsystem as well (see all the references to set/clear bit when
changing keytables for example).

This patch separate the different usages in preparation for
upcoming patches.

Where a single protocol is expected, enum rc_type is used; where one or more
protocol(s) are expected, something like u64 is used.

The patch has been rewritten so that the format of the sysfs "protocols"
file is no longer altered (at the loss of some detail). The file itself
should probably be deprecated in the future though.

Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: gpio-ir-recv: add allowed_protos for platform data

It's better to give platform code a chance to specify the allowed
protocols to use.

[mchehab@redhat.com: fix merge conflict with a patch that made
half of this change]
Signed-off-by: Du, Changbin <changbin.du@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: gpio-ir-recv: switch to module_platform_driver

Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: gpio-ir-recv: add map name

Make it possible for gpio-ir-recv users to choose a map name.

Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: gpio-ir-recv: fix missing udev by-path entry

Add missing information so that udev can create an entry for gpio-ir-recv under
/dev/input/by-path/ .

Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gpio-ir-recv: a couple signedness bugs

There are couple places where we check unsigned values for negative. I
changed ->gpin_nr to signed because in gpio_ir_recv_probe() we do:
if (pdata->gpio_nr < 0)
return -EINVAL;
I also change gval to a signed int in gpio_ir_recv_irq() because that's
the type that gpio_get_value_cansleep() returns and we test for negative
returns.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc: Add support for GPIO based IR Receiver driver

Adds GPIO based IR Receiver driver. It decodes signals using decoders
available in rc framework.

Signed-off-by: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>