RDMA: Support more than 255 rdma ports

Current code uses many different types when dealing with a port of a RDMA
device: u8, unsigned int and u32. Switch to u32 to clean up the logic.

This allows us to make (at least) the core view consistent and use the
same type. Unfortunately not all places can be converted. Many uverbs
functions expect port to be u8 so keep those places in order not to break
UAPIs. HW/Spec defined values must also not be changed.

With the switch to u32 we now can support devices with more than 255
ports. U32_MAX is reserved to make control logic a bit easier to deal
with. As a device with U32_MAX ports probably isn't going to happen any
time soon this seems like a non issue.

When a device with more than 255 ports is created uverbs will report the
RDMA device as having 255 ports as this is the max currently supported.

The verbs interface is not changed yet because the IBTA spec limits the
port size in too many places to be u8 and all applications that relies in
verbs won't be able to cope with this change. At this stage, we are
extending the interfaces that are using vendor channel solely

Once the limitation is lifted mlx5 in switchdev mode will be able to have
thousands of SFs created by the device. As the only instance of an RDMA
device that reports more than 255 ports will be a representor device and
it exposes itself as a RAW Ethernet only device CM/MAD/IPoIB and other
ULPs aren't effected by this change and their sysfs/interfaces that are
exposes to userspace can remain unchanged.

While here cleanup some alignment issues and remove unneeded sanity
checks (mainly in rdmavt),

Link: https://lore.kernel.org/r/20210301070420.439400-1-leon@kernel.org
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>

RDMA: Start use ib_device_ops

Make all the required change to start use the ib_device_ops structure.

Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

IB: Add rdma_cap_ib_switch helper and use where appropriate

Persuant to Liran's comments on node_type on linux-rdma
mailing list:

In an effort to reform the RDMA core and ULPs to minimize use of
node_type in struct ib_device, an additional bit is added to
struct ib_device for is_switch (IB switch). This is needed
to be initialized by any IB switch device driver. This is a
NEW requirement on such device drivers which are all
"out of tree".

In addition, an ib_switch helper was added to ib_verbs.h
based on the is_switch device bit rather than node_type
(although those should be consistent).

The RDMA core (MAD, SMI, agent, sa_query, multicast, sysfs)
as well as (IPoIB and SRP) ULPs are updated where
appropriate to use this new helper. In some cases,
the helper is now used under the covers of using
rdma_[start end]_port rather than the open coding
previously used.

Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/mad: Enable loopback of DR SMP responses from userspace

The local loopback of an outgoing DR SMP response is limited to those
that originate at the driver specific SMA implementation during the
driver specific process_mad() function. This patch enables a
returning DR SMP originating in userspace (or elsewhere) to be
delivered to the local managment stack. In this specific case the
driver process_mad() function does not consume or process the MAD, so
a reponse mad has not be created and the original MAD must manually be
copied to the MAD buffer that is to be handed off to the local agent.

Signed-off-by: Steve Welch <swelch@systemfabricworks.com>
Acked-by: Hal Rosenstock <hal@xsigo.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

IB/mad: Enhance SMI for switch support

Extend the SMI with switch (intermediate hop) support. Care has been
taken to ensure that the CA (and router) code paths are changed as
little as possible.

Signed-off-by: Suresh Shelvapille <suri@baymicrosystems.com>
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

IB/mad: Change SMI to use enums rather than magic return codes

Clarify code by changing return values from SMI functions to named
enum values instead of magic 0/1 values.

Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

IB/mad: Simplify SMI by eliminating smi_check_local_dr_smp()

The call to ib_get_agent_port() shouldn't be possible to fail when
smi_check_local_dr_smp() is called from ib_mad_recv_done_handler().
When it is called from handle_outgoing_dr_smp(), the device and
port_num come from mad_agent_priv so I assume the call to
ib_get_agent_port() shouldn't fail either. In either case,
smi_check_local_smp() only uses the mad_agent pointer to check that
mad_agent->device->process_mad is not NULL. The device pointer would
have to be the same as the one passed to smi_check_local_dr_smp()
since that pointer is used later instead of the one checked in
smi_check_local_smp().

Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

[IB] Fix MAD layer DMA mappings to avoid touching data buffer once mapped

The MAD layer was violating the DMA API by touching data buffers used
for sends after the DMA mapping was done. This causes problems on
non-cache-coherent architectures, because the device doing DMA won't
see updates to the payload buffers that exist only in the CPU cache.

Fix this by having all MAD consumers use ib_create_send_mad() to
allocate their send buffers, and moving the DMA mapping into the MAD
layer so it can be done just before calling send (and after any
modifications of the send buffer by the MAD layer).

Tested on a non-cache-coherent PowerPC 440SPe system.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!