iio: adc: adding support for PAC193x

This is the iio driver for Microchip
PAC193X series of Power Monitor with Accumulator chip family.

Signed-off-by: Marius Cristea <marius.cristea@microchip.com>
Link: https://lore.kernel.org/r/20240222164206.65700-3-marius.cristea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-ads1298: Add driver

Skeleton driver for the TI ADS1298 medical ADC. This device is
typically used for ECG and similar measurements. Supports data
acquisition at configurable scale and sampling frequency.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Link: https://lore.kernel.org/r/20240216153020.485201-2-mike.looijmans@topic.nl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add support for AD7091R-8

Add support for Analog Devices AD7091R-2, AD7091R-4, and AD7091R-8
low power 12-Bit SAR ADCs with SPI interface.
Extend ad7091r-base driver so it can be used by the AD7091R-8 driver.

Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/09d1d1c4b39cecc528488efac6094233715f5659.1703013352.git.marcelo.schmitt1@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Split AD7091R-5 config symbol

Split AD7091R-5 kconfig symbol into one symbol for the base AD7091R driver
and another one for the I2C interface AD7091R-5 driver.

Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/8cae37c611c1b0fe3faef7a4b8c4cc915eaeddc7.1703013352.git.marcelo.schmitt1@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add driver support for MAX34408/9

The MAX34408/MAX34409 are two- and four-channel current monitors that are
configured and monitored with a standard I2C/SMBus serial interface. Each
unidirectional current sensor offers precision high-side operation with a
low full-scale sense voltage. The devices automatically sequence through
two or four channels and collect the current-sense samples and average them
to reduce the effect of impulse noise. The raw ADC samples are compared to
user-programmable digital thresholds to indicate overcurrent conditions.
Overcurrent conditions trigger a hardware output to provide an immediate
indication to shut down any necessary external circuitry.

Add as ADC driver which only supports current monitoring for now.

Link: https://www.analog.com/media/en/technical-documentation/data-sheets/MAX34408-MAX34409.pdf

Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com>
Link: https://lore.kernel.org/r/20231014211254.16719-3-fr0st61te@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: adding support for MCP3564 ADC

This is the iio driver for Microchip family of 153.6 ksps,
Low-Noise 16/24-Bit Delta-Sigma ADCs with an SPI interface
(Microchip's MCP3461, MCP3462, MCP3464, MCP3461R, MCP3462R,
MCP3464R, MCP3561, MCP3562, MCP3564, MCP3561R,
MCP3562R and MCP3564R analog to digital converters).

Signed-off-by: Marius Cristea <marius.cristea@microchip.com>
Link: https://lore.kernel.org/r/20230829154133.40716-3-marius.cristea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: add ltc2309 support

The LTC2309 is an 8-Channel, 12-Bit SAR ADC with an I2C Interface.

This implements support for all single-ended and differential channels,
in unipolar mode only.

Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Link: https://lore.kernel.org/r/20230828-ltc2309-v3-2-338b3a8fab8b@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add Allwinner D1/T113s/R329/T507 SoCs GPADC

The General Purpose ADC (GPADC) can convert the external signal into
a certain proportion of digital value, to realize the measurement of
analog signal, which can be applied to power detection and key detection.

Theoretically, this ADC can support up to 16 channels. All SoCs below
contain this GPADC IP. The only difference between them is the number
of available channels:

T113 - 1 channel
D1 - 2 channels
R329 - 4 channels
T507 - 4 channels

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-3-bigunclemax@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: max77541: Add ADI MAX77541 ADC Support

The MAX77541 has an 8-bit Successive Approximation Register (SAR) ADC
with four multiplexers for supporting the telemetry feature.

Signed-off-by: Okan Sahin <okan.sahin@analog.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230412111256.40013-4-okan.sahin@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>

iio: adc: Add TI ADS1100 and ADS1000

The ADS1100 is a 16-bit ADC (at 8 samples per second).
The ADS1000 is similar, but has a fixed data rate.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230307065535.7927-2-mike.looijmans@topic.nl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: add imx93 adc support

The ADC in i.mx93 is a total new ADC IP, add a driver to support
this ADC.

Currently, only support one shot normal conversion triggered by
software. For other mode, will add in future.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20230117135137.1735536-2-haibo.chen@nxp.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-ads7924: add Texas Instruments ADS7924 driver

The Texas Instruments ADS7924 is a 4 channels, 12-bit analog to
digital converter (ADC) with an I2C interface.

Datasheet: https://www.ti.com/lit/gpn/ads7924
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230115170623.3680647-2-hugo@hugovil.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: add ADC driver for the TI LMP92064 controller

The TI LMP92064 is a dual 12 Bit ADC connected via SPI.
The two channels are intended for simultaneous measurements of the voltage
across- and current through a load to allow accurate instantaneous power
measurements.
The driver does not yet take advantage of this feature, as buffering is not
yet implemented.

Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Link: https://lore.kernel.org/r/20221128133503.1355898-2-l.goehrs@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad4130: add AD4130 driver

AD4130-8 is an ultra-low power, high precision, measurement solution for
low bandwidth battery operated applications.

The fully integrated AFE (Analog Front-End) includes a multiplexer for up
to 16 single-ended or 8 differential inputs, PGA (Programmable Gain
Amplifier), 24-bit Sigma-Delta ADC, on-chip reference and oscillator,
selectable filter options, smart sequencer, sensor biasing and excitation
options, diagnostics, and a FIFO buffer.

Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20221021104115.1812486-3-demonsingur@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: mt6370: Add MediaTek MT6370 support

MediaTek MT6370 is a SubPMIC consisting of a single cell battery charger
with ADC monitoring, RGB LEDs, dual channel flashlight, WLED backlight
driver, display bias voltage supply, one general purpose LDO, and the
USB Type-C & PD controller complies with the latest USB Type-C and PD
standards.

Add support for the MT6370 ADC driver for system monitoring, including
charger current, voltage, and temperature.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Link: https://lore.kernel.org/r/81ec58ae89030e48508d6810396de2679c40d26c.1665488982.git.chiaen_wu@richtek.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: add max11410 adc driver

Adding support for max11410 24-bit, 1.9ksps delta-sigma adc which
has 3 differential reference and 10 differential channel inputs.
Inputs and references can be buffered internally. Inputs can also
be amplified with internal PGA.

Device has four digital filter modes: FIR50/60, FIR50, FIR60 and SINC4.
FIR 50Hz and 60Hz rejections can be enabled/disabled separately.
Digital filter selection affects sampling frequency range so driver
has to consider the configured filter when configuring sampling frequency.

Signed-off-by: Ibrahim Tilki <Ibrahim.Tilki@analog.com>
Link: https://lore.kernel.org/r/20221003105903.229-2-Ibrahim.Tilki@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: add max11205 adc driver

Adding support for max11205 16-bit single-channel ultra-low power
delta-sigma adc.
The MAX11205 is compatible with the 2-wire interface and uses
SCLK and RDY/DOUT for serial communications. In this mode, all
controls are implemented by timing the high or low phase of the SCLK.
The 2-wire serial interface only allows for data to be read out through
the RDY/DOUT output.

Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX11205.pdf
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220831133021.215625-2-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: stx104: Move to addac subdirectory

The stx104 driver supports both ADC and DAC functionality.

Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20220815222921.138945-1-william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add rtq6056 support

Add Richtek rtq6056 supporting.

It can be used for the system to monitor load current and power with 16-bit
resolution.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/1658242365-27797-3-git-send-email-u0084500@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: qcom-spmi-rradc: introduce round robin adc

The Round Robin ADC is responsible for reading data about the rate of
charge from the USB or DC input ports, it can also read the battery
ID (resistence), skin temperature and the die temperature of the pmic.
It is found on the PMI8998 and PM660 Qualcomm PMICs.

Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20220429220904.137297-6-caleb.connolly@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio:adc:ad7280a: Move out of staging

This is a rather unusual device (in IIO anyway). However, it has
a near to standard userspace ABI.

Note the work to move this out of staging was done against a minimal
QEMU model, which doesn't model all the features of the device.
I have no intention to upstream the QEMU model as it was developed
just to enable this driver cleanup.

https://github.com/jic23/qemu/tree/ad7280a-hacks

Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://lore.kernel.org/r/20220206190328.333093-21-jic23@kernel.org

iio: adc: Add Xilinx AMS driver

The AMS includes an ADC as well as on-chip sensors that can be used to
sample external voltages and monitor on-die operating conditions, such
as temperature and supply voltage levels. The AMS has two SYSMON blocks.
PL-SYSMON block is capable of monitoring off chip voltage and
temperature.

PL-SYSMON block has DRP, JTAG and I2C interface to enable monitoring
from an external master. Out of these interfaces currently only DRP is
supported. Other block PS-SYSMON is memory mapped to PS.

The AMS can use internal channels to monitor voltage and temperature as
well as one primary and up to 16 auxiliary channels for measuring
external voltages.

The voltage and temperature monitoring channels also have event capability
which allows to generate an interrupt when their value falls below or
raises above a set threshold.

Co-developed-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
Link: https://lore.kernel.org/r/20211203212358.31444-4-anand.ashok.dumbre@xilinx.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC

The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add
driver support for this ADC.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210925020555.129-2-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add driver for Renesas RZ/G2L A/D converter

Add ADC driver support for Renesas RZ/G2L A/D converter in SW
trigger mode.

A/D Converter block is a successive approximation analog-to-digital
converter with a 12-bit accuracy and supports a maximum of 8 input
channels.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210804202118.25745-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: add ADC driver for the TI TSC2046 controller

Basically the TI TSC2046 touchscreen controller is 8 channel ADC optimized for
the touchscreen use case. By implementing it as an IIO ADC device, we can
make use of resistive-adc-touch and iio-hwmon drivers.

Polled readings are currently not implemented to keep this patch small, so
iio-hwmon will not work out of the box for now.

So far, this driver was tested with a custom version of resistive-adc-touch driver,
since it needs to be extended to make use of Z1 and Z2 channels. The X/Y
are working without additional changes.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210428073208.19570-4-o.rempel@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add driver for Texas Instruments ADS131E0x ADC family

The ADS131E0x are a family of multichannel, simultaneous sampling,
24-bit, delta-sigma, analog-to-digital converters (ADCs) with a
built-in programmable gain amplifier (PGA), internal reference
and an onboard oscillator.

Datasheet: https://www.ti.com/lit/ds/symlink/ads131e08.pdf
Signed-off-by: Tomislav Denis <tomislav.denis@avl.com>
Link: https://lore.kernel.org/r/20210202084107.3260-2-tomislav.denis@avl.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: mt6360: Add ADC driver for MT6360

Add MT6360 ADC driver including Charger Current, Voltage, and
Temperature.

Signed-off-by: Gene Chen <gene_chen@richtek.com>
Link: https://lore.kernel.org/r/1603181267-15610-4-git-send-email-gene.chen.richtek@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: mp2629: Add support for mp2629 ADC driver

Add support for 8-bit resolution ADC readings for input power
supply and battery charging measurement. Provides voltage, current
readings to mp2629 power supply driver.

Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

iio: adc: Add MAX1241 driver

Add driver for the Maxim MAX1241 12-bit, single-channel ADC.

Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX1240-MAX1241.pdf
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Lazar <alazar@startmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad9467: add support AD9467 ADC

The AD9467 is a 16-bit, monolithic, IF sampling analog-to-digital converter
(ADC). It is optimized for high performanceover wide bandwidths and ease of
use. The product operates at a 250 MSPS conversion rate and is designed for
wireless receivers, instrumentation, and test equipment that require a high
dynamic range. The ADC requires 1.8 V and 3.3 V power supplies and a low
voltage differential input clock for full performance operation. No
external reference or driver components are required for many applications.
Data outputs are LVDS compatible (ANSI-644 compatible) and include the
means to reduce the overall current needed for short trace distances.

Since the chip can operate at such high sample-rates (much higher than
classical interfaces), it requires that a DMA controller be used to
interface directly to the chip and push data into memory.
Typically, the AXI ADC IP core is used to interface with it.

Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/AD9467.pdf

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: adi-axi-adc: add support for AXI ADC IP core

This change adds support for the Analog Devices Generic AXI ADC IP core.
The IP core is used for interfacing with analog-to-digital (ADC) converters
that require either a high-speed serial interface (JESD204B/C) or a source
synchronous parallel interface (LVDS/CMOS).

Usually, some other interface type (i.e SPI) is used as a control interface
for the actual ADC, while the IP core (controlled via this driver), will
interface to the data-lines of the ADC and handle the streaming of data
into memory via DMA.

Because of this, the AXI ADC driver needs the other SPI-ADC driver to
register with it. The SPI-ADC needs to be register via the SPI framework,
while the AXI ADC registers as a platform driver. The two cannot be ordered
in a hierarchy as both drivers have their own registers, and trying to
organize this [in a hierarchy becomes] problematic when trying to map
memory/registers.

There are some modes where the AXI ADC can operate as standalone ADC, but
those will be implemented at a later point in time.

DocLink: https://wiki.analog.com/resources/fpga/docs/axi_adc_ip

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: rn5t618: Add ADC driver for RN5T618/RC5T619

Both chips have an A/D converter capable of measuring
things like VBAT, VUSB and analog inputs.

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

staging: iio: adc: ad7192: move out of staging

Move ad7192 ADC driver out of staging into mainline.

Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: new driver to support Linear technology's ltc2496

This chip is similar to the LTC2497 ADC, it just uses SPI instead of I2C
and so has a slightly different protocol. Only the actual hardware
access is different. The spi protocol is different enough to not be able
to map the differences via a regmap.

Also generalize the entry in MAINTAINER to cover the newly introduced
file.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ltc2497: split protocol independent part in a separate module

This allows to share most of this driver for the ltc2496 driver added in
the next commit that is an SPI variant of the ltc2497. Initially I named
the generic part ltc249x, but wild card names are frowned upon, so the
generic part is called ltc2497-core even though it's not obvious that
this is then to be reused for the ltc2496 driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Move AD7091R5 entry in a alphabetical order in Makefile

Ad7091R5 was added in a non alphabetical order after AD7124 in Makefile and
KConfig. This patch fixes that and place Ad7091R5 before AD7124.

Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add support for AD7091R5 ADC

AD7091R5 is 4-Channel, I2C, Ultra Low Power,12-Bit ADC.

This driver will also support AD7091R2/4/8 in the future.

Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7091r-5.pdf

Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add driver support for AD7292

The AD7292 is a 10-bit monitor and control system with ADC, DACs,
temperature sensor, and GPIOs.

Configure AD7292 devices in direct access mode, enabling single-ended
ADC readings.

Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7292.pdf

Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: New driver for the AB8500 GPADC

This is a new driver for the ST-Ericsson AB8500 GPADC, which
replaces the old driver in drivers/mfd/ab8500-gpadc.c and
thus gets rid of another necessarily different custom driver
from the times before IIO existed.

The AB8500 GPADC can convert 10 different channels and these
are used for monitoring voltages in the U8500 chipset, some
are used for battery charging, some for temperature
monitoring.

As this is very core functionality that a lot of drivers
depend on and was formerly compiled in with the AB8500 core
driver, we deafault it to 'y' in Kconfig: it can be compiled
out but it is really not advisible: the platform can
for example overheat if we do.

Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver

Exposes the ADC device present on, at least, Intel Merrifield platform.

Based on work done by:
Yang Bin <bin.yang@intel.com>
Huiquan Zhong <huiquan.zhong@intel.com>
Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Pavan Kumar S <pavan.kumar.s@intel.com>

Though it has been heavily rewritten for upstream.

Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add driver for the TI ADS8344 A/DC chips

This adds support for the Texas Instruments ADS8344 ADC chip. This chip
has a 16-bit 8-Channel ADC and is access directly through SPI.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad7780: moving ad7780 out of staging

Move ad7780 ADC driver out of staging and into the mainline.

The ad7780 is a sigma-delta analog to digital converter. This driver provides
reading voltage values and status bits from both the ad778x and ad717x series.
Its interface also allows writing on the FILTER and GAIN GPIO pins on the
ad778x.

Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
Co-developed-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

IIO: add Ingenic JZ47xx ADC driver.

Add an IIO driver for the ADC hardware present on Ingenic JZ47xx SoCs.

Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add AD7768-1 ADC basic support

The ad7768-1 is a single channel, precision 24-bit analog to digital
converter (ADC).

This basic patch configures the device in fast mode, with 32 kSPS and
leaves the default sinc5 filter.

Two data conversion modes are made available. When data is retrieved by
using the read_raw attribute, one shot single conversion mode is set.
The continuous conversion mode is enabled when the triggered buffer
mechanism is used. To assure correct data retrieval, the driver waits
for the interrupt triggered by the low to high transition of the DRDY
pin.

Datasheets:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7768-1.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: add NPCM ADC driver

Add Nuvoton NPCM BMC Analog-to-Digital Converter(ADC) driver.

The NPCM ADC is a 10-bit converter for eight channel inputs.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: add STMPE ADC driver using IIO framework

This adds an ADC driver for the STMPE device using the industrial
input/output interface. The driver supports raw reading of values.
The driver depends on the MFD STMPE driver. If the touchscreen
block is enabled too, only four of the 8 ADC channels are available.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

iio: adc: Add the TI ads124s08 ADC code

Introduce the TI ADS124S08 and the ADS124S06 ADC
devices from TI. The ADS124S08 is the 12 channel ADC
and the ADS124S06 is the 6 channel ADC device

These devices share a common datasheet:
http://www.ti.com/lit/gpn/ads124s08

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: adc: ad7606: Move out of staging

Move ad7606 ADC driver out of staging and into the mainline.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add ad7124 support

The ad7124-4 and ad7124-8 are a family of 4 and 8 channel sigma-delta ADCs
with 24-bit precision and reference.

Three power modes are available which in turn affect the output data rate:
* Full power: 9.38 SPS to 19,200 SPS
* Mid power: 2.34 SPS to 4800 SPS
* Low power: 1.17 SPS to 2400 SPS

The ad7124-4 can be configured to have four differential inputs, while
ad7124-8 can have 8. Moreover, ad7124 also supports per channel
configuration. Each configuration consists of gain, reference source,
output data rate and bipolar/unipolar configuration.

Datasheets:
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/AD7124-4.pdf
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/ad7124-8.pdf

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio:adc:ad7949: Add AD7949 ADC driver family

Compatible with AD7682 and AD7689 chips.
It is a Analog Devices ADC driver 14/16 bits 4/8 channels
with SPI protocol

Datasheet of the device:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7949.pdf

Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: add support for mcp3911

MCP3911 is a dual channel Analog Front End (AFE) containing two
synchronous sampling delta-sigma Analog-to-Digital Converters (ADC).

Co-developed-by: Kent Gustavsson <kent@minoris.se>
Signed-off-by: Kent Gustavsson <kent@minoris.se>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add QCOM SPMI PMIC5 ADC driver

This patch adds support for QCOM SPMI PMIC5 family
of ADC driver that supports hardware based offset and
gain compensation. The ADC peripheral can measure both
voltage and current channels whose input signal is
connected to the PMIC ADC AMUX.

The register set and configuration has been refreshed
compared to the prior QCOM PMIC ADC family. Register
ADC5 as part of the IIO framework.

Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add Spreadtrum SC27XX PMICs ADC support

The Spreadtrum SC27XX PMICs ADC controller contains 32 channels,
which is used to sample voltages with 12 bits conversion.

[Baolin Wang did lots of improvements]

Signed-off-by: Freeman Liu <freeman.liu@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

IIO: ADC: add STM32 DFSDM sigma delta ADC support

Add DFSDM driver to handle sigma delta ADC.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

IIO: ADC: add stm32 DFSDM core support

Add driver for stm32 DFSDM pheripheral. Its converts a sigma delta
stream in n bit samples through a low pass filter and an integrator.
stm32-dfsdm-core driver is the core part supporting the filter
instances dedicated to sigma-delta ADC or audio PDM microphone purpose.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

IIO: ADC: add sigma delta modulator support

Add generic driver to support sigma delta modulators.
Typically, this device is hardware connected to
an IIO device in charge of the conversion. Devices are
bonded through the hardware consumer API.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: New driver for Cirrus Logic EP93xx ADC

New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
Board specific code must take care to create plaform device with all necessary
resources.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add support for DLN2 ADC

This patch adds support for Diolan DLN2 ADC via IIO's ADC interface.
ADC is the fourth and final component of the DLN2 for the kernel.

Signed-off-by: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: Add LTC2471/LTC2473 driver

The LTC2741 and LTC2473 are single voltage ADC chips. The LTC2473
is similar to the LTC2471 but outputs a signed differential value.

Datasheet:
http://cds.linear.com/docs/en/datasheet/24713fb.pdf

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add support for TI ADC108S102 and ADC128S102

This is an upstream port of an IIO driver for the TI ADC108S102 and
ADC128S102. The former can be found on the Intel Galileo Gen2 and the
Siemens SIMATIC IOT2000. For those boards, ACPI-based enumeration is
included.

Due to the lack of regulators under ACPI, we hard-code the voltage
provided to the VA pin of the ADC to 5 V, the value used on Galileo and
IOT2000. For DT usage, the regulator "vref-supply" provides this
information. Note that DT usage has not been tested.

Original author: Bogdan Pricop <bogdan.pricop@emutex.com>
Ported from Intel Galileo Gen2 BSP to Intel Yocto kernel:
Todor Minchev <todor@minchev.co.uk>.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add driver for the ti-adc084s021 chip

This adds support for the Texas Instruments ADC084S021 ADC chip.

Signed-off-by: Mårten Lindahl <martenli@axis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs

The X-Powers AXP20X and AXP22X PMICs have multiple ADCs. They expose the
battery voltage, battery charge and discharge currents, AC-in and VBUS
voltages and currents, 2 GPIOs muxable in ADC mode and PMIC temperature.

This adds support for most of AXP20X and AXP22X ADCs.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

iio: adc: add max1117/max1118/max1119 ADC driver

This adds max1117/max1118/max1119 8-bit, dual-channel ADC driver.

This new driver uses the zero length spi_transfers with the cs_change
flag set and/or the non-zero delay_usecs.

1. The zero length transfer with the spi_transfer.cs_change set is
required in order to select CH1. The chip select line must be brought
high and low again without transfer.

2. The zero length transfer with the spi_transfer.delay_usecs > 0 is
required for waiting the conversion to be complete. The conversion
begins with the falling edge of the chip select. During the conversion
process, SCLK is ignored.

These two usages are unusual. But the spi controller drivers that use
a default implementation of transfer_one_message() are likely to work.
(I've tested this adc driver with spi-omap2-mcspi and spi-xilinx)

On the other hand, some spi controller drivers that have their own
transfer_one_message() may not work. But at least for the zero length
transfer with delay_usecs > 0, I'm proposing a new testcase for the
spi-loopback-test that can test whether the delay_usecs setting has
taken effect.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add a driver for Qualcomm PM8xxx HK/XOADC

The Qualcomm PM8xxx PMICs contain a simpler ADC than its
successors (already in the kernel as qcom-spmi-vadc.c):
the HK/XO ADC (Housekeeping/Chrystal oscillator ADC).

As far as I can understand this is equal to the PMICs
using SSBI transport and encompass PM8018, PM8038,
PM8058, and PM8921, so this is shortly named PM8xxx.

This ADC monitors a bunch of on-board voltages and the die
temperature of the PMIC itself, but it can also be routed
to convert a few external MPPs (multi-purpose pins). On
the APQ8060 DragonBoard this feature is used to let this
ADC convert an analog ALS (Ambient Light Sensor) voltage
signal from a Capella CM3605 ALS into a LUX value.

Developed and tested with APQ8060 DragonBoard based on
Ivan's driver and Rama Krishna's patches. The SPMI VADC
driver is quite different, but share enough minor
functionality that I have split out to the common file
in a previous patch.

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: break out common code from SPMI VADC

The SPMI VADC and the earlier XOADC share a subset of
common code, so to be able to use the same code in both
drivers, we break out a separate file with the common code,
prefix exported functions that are no longer static with
qcom_* and bake an object qcom-spmi-vadc.o that contains both
files: qcom-vadc-common.o and qcom-spmi-vadc-core.o.

As we need to follow the procedure for making a kernel module
or compiled in object from several files, but still want to
produce the same module name, rename the qcom-spmi-vadc.c
file to qcom-spmi-vadc-core.c so we can bake the two objects
into qcom-spmi-vadc.o

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add Maxim max9611 ADC driver

Add iio driver for Maxim max9611 and max9612 current-sense amplifiers
with 12-bits ADC interface.

Datasheet publicly available at:
https://datasheets.maximintegrated.com/en/ds/MAX9611-MAX9612.pdf

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adc: Driver for Linear Technology LTC2497 ADC

This patch adds support for the Analog Devices / Linear Technology
LTC2497 ADCs. The LTC2497 is a 16-channel (eight differential),
16-bit, high precision, delta-sigma ADC with an automatic, differential,
input current cancellation front end and a 2-wire, I2C interface.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Aspeed ADC

Aspeed BMC SoCs include a 16 channel, 10-bit ADC. Low and high threshold
interrupts are supported by the hardware but are not currently implemented.

Signed-off-by: Rick Altherr <raltherr@google.com>
Tested-by: Xo Wang <xow@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: cpcap: Add minimal support for CPCAP PMIC ADC

On Motorola phones like droid 4 there is a custom CPCAP PMIC. This PMIC
has ADCs that are used for battery charging and USB PHY VBUS and ID pin
detection.

Unfortunately the only documentation for this ADC seems to be the
Motorola mapphone Linux kernel tree. I have tested that reading raw and
scaled values works, but I have not used the timed sampling that the ADC
seems to support.

Let's add a minimal support for it so we can eventually provide IIO
channels for the related battery charging and USB PHY drivers.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: mxs-lradc: Remove driver

Since the driver has been split into MFD there is no reason for it to
stay, so remove it.

Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

iio: adc: mxs-lradc: Add support for ADC driver

Add support for sixteen-channel 12-bit resolution ADC and its functions,
which include general-purpose ADC readings, battery voltage measurement,
and die temperature measurement.

Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

iio: adc: add support for Allwinner SoCs ADC

The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. This patch adds the ADC driver which is
based on the MFD for the same SoCs ADC.

This also registers the thermal adc channel in the iio map array so
iio_hwmon could use it without modifying the Device Tree. This registers
the driver in the thermal framework.

The thermal sensor requires the IP to be in touchscreen mode to return
correct values. Therefore, if the user is continuously reading the ADC
channel(s), the thermal framework in which the thermal sensor is
registered will switch the IP in touchscreen mode to get a temperature
value and requires a delay of 100ms (because of the mode switching),
then the ADC will switch back to ADC mode and requires also a delay of
100ms. If the ADC readings are critical to user and the SoC temperature
is not, this driver is capable of not registering the thermal sensor in
the thermal framework and thus, "quicken" the ADC readings.

This driver probes on three different platform_device_id to take into
account slight differences (registers bit and temperature computation)
between Allwinner SoCs ADCs.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging:iio:adc:lpc32xx Move out of staging.

There are a few more little cleanups that could be done on this driver, but
I don't think any are sufficient to justify not moving it out of staging.

It's a very simple driver (presumably for a simple part) so not much that can
go wrong. I think it was only ever in staging because that's where IIO was
as a whole at the time and then we forgot about it!

Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging:iio:adc:spear Move out of staging.

There are some unanswered questions due to disagreements between the code
and various datasheets (including between different datasheets for the same
part).

I don't think that is necessarily a reason to keep it in staging however.
I'm partly posting this patch inorder to reignite debate and with a bit
of luck find someone who has one of these to test!

Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs

This adds support for the SAR (Successive Approximation Register) ADC
on the Amlogic Meson SoCs.

The code is based on the public S805 (Meson8b) and S905 (GXBB)
datasheets (see [0] and [1]), as well as by reading (various versions
of) the vendor driver and by inspecting the registers on the vendor
kernels of my testing-hardware.

Currently the GXBB, GXL and GXM SoCs are supported. GXBB hardware has
10-bit ADC resolution, while GXL and GXM have 12-bit ADC resolution.
The code was written to support older SoCs (Meson8 and Meson8b) as well,
but due to lack of actual testing-hardware no of_device_id was added for
these.

Two "features" from the vendor driver are currently missing:
- the vendor driver uses channel #7 for calibration (this improves the
accuracy of the results - in my tests the results were less than 3%
off without calibration compared to the vendor driver). Adding support
for this should be easy, but is not required for most applications.
- channel #6 is connected to the SoCs internal temperature sensor.
Adding support for this is probably not so easy since (based on the
u-boot sources) most SoC versions are using different registers and
algorithms for the conversion from "ADC value" to temperature.

Supported by the hardware but currently not supported by the driver:
- reading multiple channels at the same time (the hardware has a FIFO
buffer which stores multiple results)
- continuous sampling (this would require a way to enable this
individually because otherwise the ADC would be drawing power
constantly)
- interrupt support (similar to the vendor driver this new driver is
polling the results. It is unclear if the IRQ-mode is supported on
older (Meson6 or Meson8) hardware as well or if there are any errata)

[0]
http://dn.odroid.com/S805/Datasheet/S805_Datasheet%20V0.8%2020150126.pdf
[1] http://dn.odroid.com/S905/DataSheet/S905_Public_Datasheet_V1.1.4.pdf

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add Renesas GyroADC driver

Add IIO driver for the Renesas RCar GyroADC block. This block is a
simple 4/8-channel ADC which samples 12/15/24 bits of data every
cycle from all channels.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: tlc4541: add support for TI tlc4541 adc

This adds TI's tlc4541 16-bit ADC driver. Which is a single channel
ADC. Supports raw and trigger buffer access.
Also supports the tlc3541 14-bit device, which has not been tested.
Implementation of the tlc3541 is fairly straight forward thou.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add Maxim MAX11100 driver

Add iio driver for Maxim MAX11100 single-channel ADC.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: hx711: Add IIO driver for AVIA HX711

This is the IIO driver for AVIA HX711 ADC which is mostly used in weighting
cells.

The protocol is quite simple and using GPIOs:
One GPIO is used as clock (SCK) while another GPIO is read (DOUT)

The raw value read from the chip is delivered.
To get a weight one needs to subtract the zero offset and scale it.

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: New driver for TI ADS7950 chips

This adds a new driver for the TI ADS7950 family of ADC chips. These
communicate using SPI and come in 8/10/12-bit and 4/8/12/16 channel
varieties.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add support for STM32 ADC

This patch adds support for STMicroelectronics STM32 MCU's analog to
digital converter.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add support for STM32 ADC core

Add core driver for STMicroelectronics STM32 ADC (Analog to Digital
Converter). STM32 ADC can be composed of up to 3 ADCs with shared
resources like clock prescaler, common interrupt line and analog
reference voltage.
This core driver basically manages shared resources.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: envelope-detector: ADC driver based on a DAC and a comparator

The DAC is used to find the peak level of an alternating voltage input
signal by a binary search using the output of a comparator wired to
an interrupt pin. Like so:
_
| \
input +------>-------|+ \
| \
.-------. | }---.
| | | / |
| dac|-->--|- / |
| | |_/ |
| | |
| | |
| irq|------<-------'
| |
'-------'

Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adc: Add support for AD7766/AD7767

Add support for the AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1, AD7767-2
Analog to Digital converters. It's a family of single channel 24-bit SAR
ADCs. They are all digital interface compatible and the main difference is
the internal decimation rate and analog performance. For communication with
the host processor a SPI interface is used.

In addition the part has a data ready pin that is pulsed for one MCLK cycle
when a conversion has completed and can be used as a IIO trigger.

Datasheets:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7766.pdf
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7767.pdf

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: stx104: Add IIO support for the ADC channels

The Apex Embedded Systems STX104 features 16 channels of single-ended (8
channels of true differential) 16-bit analog input. Differential input
configuration may be selected via a physical jumper on the device.
Similarly, input polarity (unipolar/bipolar) is configured via a
physical jumper on the device.

Input gain selection is available to the user via software, thus
allowing eight possible input ranges: +-10V, +-5V, +-2.5V, +-1.25V,
0 to 10V, 0 to 5V, 0 to 2.5V, and 0 to 1.25V. Four input gain
configurations are supported: x1, x2, x4, and x8.

This ADC resolution is 16-bits (1/65536 of full scale). Analog input
samples are taken on software trigger; neither FIFO sampling nor
interrupt triggering is supported by this driver.

The Apex Embedded Systems STX104 is primarily an analog-to-digital
converter device. The STX104 IIO driver was initially placed in the DAC
directory because only the DAC portion of the STX104 was supported at
the time. Now that ADC support has been added to the STX104 IIO driver,
the driver should be moved to the more appropriate ADC directory.

Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add ADC12130/ADC12132/ADC12138 ADC driver

This adds Texas Instruments' ADC12130/ADC12132/ADC12138 12-bit plus
sign ADC driver. I have tested with the ADC12138. The ADC12130 and
ADC12132 are not tested but these are similar to ADC12138 except that
the mode programming instruction is a bit different.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ltc2485: add support for Linear Technology LTC2485 ADC

Adds basic support for the LTC2485 ADC - a delta-sigma analog-to-digital
converter with an I2C interface that operates in single shot conversion
mode.

The driver supports an on board 5V reference and the power-on default
configuration which rejects both 50hz & 60hz line frequencies and
operates in 1x speed mode.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: mt2701: Add Mediatek auxadc driver for mt2701.

Add Mediatek auxadc driver based on iio.
It will register a device in iio and support iio.
So thermal can read auxadc channel to sample data by iio device.
It is tested successfully on mt2701 platform.
Mt8173 and mt6577 platforms are not tested.
But the expectation is compatible.

Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: ti-adc161s626: add support for TI 1-channel differential ADCs

Add support for Texas Instruments ADC141S626, and ADC161S626 chips.

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Add driver for Broadcom iproc-static-adc

This patch adds basic driver implementation for Broadcom's
static adc controller used in iProc SoC's family.

Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add NXP LPC18xx ADC driver

Add base support for the 10-bit SAR ADC peripheral found
on NXP LPC18xx/43xx SoCs.

This is a minimal driver that does not support burst mode,
interrupts, DMA or hardware triggers.

User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add TI ADS1015 ADC driver support

The driver has sysfs readings with runtime PM support for power saving.
It also offers buffer support that can be used together with IIO software
triggers.

Datasheet can be found here:
http://www.ti.com.cn/cn/lit/ds/symlink/ads1015.pdf

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add imx25-gcq ADC driver

This is a conversion queue driver for the mx25 SoC. It uses the central
ADC which is used by two seperate independent queues. This driver
prepares different conversion configurations for each possible input.
For a conversion it creates a conversionqueue of one item with the
correct configuration for the chosen channel. It then executes the queue
once and disables the conversion queue afterwards.

The reference voltages are configurable through devicetree subnodes,
depending on the connections of the ADC inputs.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

iio: adc: Move mxs-lradc out of staging

Move mxs-lradc driver from drivers/staging/iio/adc to drivers/iio/adc.

Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add support for ADC0831/ADC0832/ADC0834/ADC0838 chips

This adds ADC0831/ADC0832/ADC0834/ADC0838 8-bit ADC driver.
I have tested with ADC0831 and ADC0832. The remaining ADC0834 and
ADC0838 are very similar to ADC0832.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adc:at91_adc8xx: introduce new atmel adc driver

This driver supports the new version of the Atmel ADC device introduced
with the SAMA5D2 SoC family.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add IMX7D ADC driver support

Freescale i.MX7D soc contains a new ADC IP. This patch add this ADC
driver support, and the driver only support ADC software trigger.

Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: ina2xx: add support for TI INA2xx Power Monitors

in SOFTWARE buffer mode, a kthread will capture the active scan_elements
into a kfifo, then compute the remaining time until the next capture tick
and do an active wait (udelay).

This will produce a stream of up to fours channels plus a 64bits
timestamps (ns).

Tested with ina226, on BeagleBoneBlack.

Datasheet: http://www.ti.com/lit/gpn/ina226

Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add TI ADS8688

This patch adds support for the Texas Intruments ADS8688 ADC.

Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Martin Hundebøll <martin.hundeboll@prevas.dk>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adc: add iio driver for Palmas (twl6035/7) gpadc

This driver code was found as:

https://android.googlesource.com/kernel/tegra/+/aaabb2e045f31e5a970109ffdaae900dd403d17e/drivers/staging/iio/adc

Fixed various compilation issues and test this driver on omap5 evm.

Signed-off-by: Pradeep Goudagunta <pgoudagunta@nvidia.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: hi8435: Holt HI-8435 threshold detector

Add Holt threshold detector driver for HI-8435 chip

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adc:cc10001_adc: resort entry in Kconfig and Makefile

Move the entry for the CC 10001 ADC driver in Kconfig and Makefile up to
maintain alphabetic order.

Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add support for Berlin

This patch adds the support of the Berlin ADC, available on Berlin SoCs.
This ADC has 8 channels available, with one connected to a temperature
sensor.

The particularity here, is that the temperature sensor connected to the
ADC has its own registers, and both the ADC and the temperature sensor
must be configured when using it.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Add support for DA9150 GPADC

This patch adds support for DA9150 Charger & Fuel-Gauge IC GPADC.

Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

iio: adc: Cosmic Circuits 10001 ADC driver

This commit adds support for Cosmic Circuits 10001 10-bit ADC device.

Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Phani Movva <Phani.Movva@imgtec.com>
Signed-off-by: Naidu Tellapati <Naidu.Tellapati@imgtec.com>
[ezequiel: code style cleaning]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: vadc: Qualcomm SPMI PMIC voltage ADC driver

The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
15bits resolution and register space inside PMIC accessible across
SPMI bus.

The vadc driver registers itself through IIO interface.

Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: iadc: Qualcomm SPMI PMIC current ADC driver

The current ADC is peripheral of Qualcomm SPMI PMIC chips. It has
16 bits resolution and register space inside PMIC accessible across
SPMI bus.

The driver registers itself through IIO interface.

Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add support for axp288 adc

Platform driver for X-Powers AXP288 ADC, which is a sub-device of the
customized AXP288 PMIC for Intel Baytrail-CR platforms. GPADC device
enumerates as one of the MFD cell devices. It uses IIO infrastructure
to communicate with userspace and consumer drivers.

Usages of ADC channels include battery charging and thermal sensors.

Based on initial work by:
Ramakrishna Pallala <ramakrishna.pallala@intel.com>

Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

iio: adc: add driver for Rockchip saradc

The ADC is a 3-channel signal-ended 10-bit Successive Approximation
Register (SAR) A/D Converter. It uses the supply and ground as its reference
and converts the analog input signal into 10-bit binary digital codes.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add TI ADC128S052

This patch adds support for ADC128S052 from TI.

Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging:iio:ad7291: Move out of staging

The ad7291 driver is in a reasonable shape. It does not use non-standard API/ABI
and there are no major style issues with the driver. So this patch moves it out
of staging.

There is one small warning from checkpatch which is also fixed in this patch.
The patch also sorts the #include directives in alphabetical order.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: add support of the max1027

This driver add partial support of the
maxim 1027/1029/1031. Differential mode is not
supported.

It was tested on armadeus apf27 board.

Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

mfd: twl4030-madc: Move driver to drivers/iio/adc

This is a driver for an A/D converter, which belongs into
drivers/iio/adc.

Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

staging:iio: Move ad799x driver out of staging

The driver is now at a reasonable quality level. Move it out of staging.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adc: Add Xilinx XADC driver

The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx.
The XADC has a DRP interface for communication. Currently two different
frontends for the DRP interface exist. One that is only available on the ZYNQ
family as a hardmacro in the SoC portion of the ZYNQ. The other one is available
on all series 7 platforms and is a softmacro with a AXI interface. This driver
supports both interfaces and internally has a small abstraction layer that hides
the specifics of these interfaces from the main driver logic.

The ADC has a couple of internal channels which are used for voltage and
temperature monitoring of the FPGA as well as one primary and up to 16 channels
auxiliary channels for measuring external voltages. The external auxiliary
channels can either be directly connected each to one physical pin on the FPGA
or they can make use of an external multiplexer which is responsible for
multiplexing the external signals onto one pair of physical pins.

The voltage and temperature monitoring channels also have an event capability
which allows to generate a interrupt when their value falls below or raises
above a set threshold.

Buffered sampling mode is supported by the driver, but only for AXI-XADC since
the ZYNQ XADC interface does not have capabilities for supporting buffer mode
(no end-of-conversion interrupt). If buffered mode is supported the driver will
register two triggers. One "xadc-samplerate" trigger which will generate samples
with the configured samplerate. And one "xadc-convst" trigger which will
generate one sample each time the CONVST (conversion start) signal is asserted.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add MEN 16z188 ADC driver

Add support for MEN 16z188 ADC IP Core on MCB FPGAs.

Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio:adc:imx: add Freescale Vybrid vf610 adc driver

Add Freescale Vybrid vf610 adc driver. The driver only support
ADC software trigger.

VF610 ADC device documentation is available at below reference manual
(chapter 37):
http://cache.freescale.com/files/32bit/doc/ref_manual/VYBRIDRM.pdf?
fpsp=1&WT_TYPE=Reference%20Manuals&WT_VENDOR=FREESCALE&WT_FILE_FORMAT
=pdf&WT_ASSET=Documentation

CC: Shawn Guo <shawn.guo@linaro.org>
CC: Jonathan Cameron <jic23@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: Peter Meerwald <pmeerw@pmeerw.net>
CC: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add driver for Microchip MCP3422/3/4 high resolution ADC

Sysfs access to all channels.

Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: twl6030-gpadc: TWL6030, TWL6032 GPADC driver

The GPADC is general purpose ADC found on TWL6030, and TWL6032 PMIC,
known also as Phoenix and PhoenixLite.

The TWL6030 and TWL6032 have GPADC with 17 and 19 channels
respectively. Some channels have current source and are used for
measuring voltage drop on resistive load for detecting battery ID
resistance, or measuring voltage drop on NTC resistors for external
temperature measurements. Some channels measure voltage, (i.e. battery
voltage), and have voltage dividers, thus, capable to scale voltage.
Some channels are dedicated for measuring die temperature.

Some channels are calibrated in 2 points, having offsets from ideal
values kept in trim registers. This is used to correct measurements.

The differences between GPADC in TWL6030 and TWL6032:
- 10 bit vs 12 bit ADC;
- 17 vs 19 channels;
- channels have different purpose(i.e. battery voltage
channel 8 vs channel 18);
- trim values are interpreted differently.

Based on the driver patched from Balaji TK, Graeme Gregory, Ambresh K,
Girish S Ghongdemath.

Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Oleksandr Kozaruk <oleksandr.kozaruk@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Add a comment to about alphabetical order to Kconfigs and Makefiles

Keeping Makefile and Kconfig entries in alphabetical order usually works better
than just appending new entries at the end, since it reduces the amount of
conflicts. This patch adds a comment to the IIO Kconfig and Makefile files to
document that the entries should be kept in alphabetical order.

Also reorder those entries which weren't in alphabetical order yet.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Add Nuvoton NAU7802 ADC driver

The Nuvoton NAU7802 ADC is a 24-bit 2-channels I2C ADC, with adjustable
gain and sampling rates.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add driver for MCP3204/08 12-bit ADC

This adds support for Microchip's 12 bit AD converters MCP3204 and
MCP3208. These chips communicates over SPI and supports single-ended
and pseudo-differential configurations.

Signed-off-by: Oskar Andero <oskar.andero@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add exynos adc driver under iio framwork

This patch adds New driver to support:
1. Supports ADC IF found on EXYNOS4412/EXYNOS5250
and future SoCs from Samsung
2. Add ADC driver under iio/adc framework
3. Also adds the Documentation for device tree bindings

Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

IIO ADC support for AD7923

This patch adds support for Analog Devices AD7923 ADC in the IIO Subsystem.

Signed-off-by: Patrick Vasseur <patrick.vasseur@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add Texas Instruments ADC081C021/027 support

Add support for reading conversion results from the ADC and provide them
through a single IIO channel. A proper scaling factor is also exported
based on the reference voltage provided by a regulator.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging:iio: Move ad7793 driver out of staging

The driver does not expose any custom API to userspace and none of the standard
static code checker tools report any issues, so move it out of staging.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: Add viperboard adc driver

This adds the mfd cell to use the adc part of the Nano River Technologies
viperboard.

Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

staging:iio: Move the ad7298 driver out of staging

The driver does not expose any custom API to userspace and none of the standard
static code checker tools report any issues, so move it out of staging.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adc:max1363 move from staging.

Now this driver is using kfifo we can move it out of staging.

Signed-off-by: Jonathan Cameron <jic23@kernel.org>

IIO : ADC: tiadc: Add support of TI's ADC driver

This patch adds support for TI's ADC driver.
This is a multifunctional device.
Analog input lines are provided on which
voltage measurements can be carried out.
You can have upto 8 input lines.

Signed-off-by: Patil, Rachna <rachna@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

staging:iio: Move the ad7887 driver out of staging

The driver does not expose any custom API to userspace and none of the standard
static code checker tools report any issues, so move it out of staging.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: adc: add new lp8788 adc driver

TI LP8788 PMU provides regulators, battery charger, ADC,
RTC, backlight driver and current sinks.

This patch enables the LP8788 ADC functions.

The LP8788 ADC has several ADC input selection and supports 12bit resolution.
Internal operation of getting ADC is access to registers of LP8788.
The LP8788 ADC uses exported functions for accessing these registers.
(exported by LP8788 MFD device driver)

This driver supports IIO_CHAN_INFO_RAW and SCALE.
So the IIO consumer can calculate the value with raw and scale.
The unit of scale is micro.

(ADC Input Selection)

Voltage: battery voltage (MAX 5.0, 5.5 and 6.0V)
charger input voltage
four general ADC inputs
coin cell voltage
Current: battery charging current
Temperature: IC temperature

(The IIO map for the IIO consumer)

The ADC input is configurable in the platform side.
Even though this platform data is not defined,
the default IIO map is created for supporting the power supply driver.
The battery voltage and temperature are used inside this driver.

(History)

Patch v6.
(a) Fix scale value for each ADC input selection
Voltage and current type are mili unit and temperature is degree.
To calculate the IC temperature,
temp = raw * scaleint + (raw * scalepart)/ 1000000, scaleint is always 0.
= raw * 0.061050, raw: 0 ~ 4095
Then range of IC temperature(ADC result) is 0 ~ 250'C

(b) Reorganization of the IIO channel Spec
Remove address, scan_type and scan_index and rollback the datasheet name.
The reason why 'address' field is unnecessary is no relation with each channel.
Moreover, to get the raw ADC value, the address info is not only one register
but also several registers.
Therefore specific function(lp8788_get_adc_result) is called rather than
using one 'address' field.

(c) Fix coding style
Remove duplicated checking routine while unregistering the IIO map.
Fix code for space and parenthesis.

Patch v5.
Fix default consumer name as 'lp8788-charger'.
Add mutex for ADC read operation.
Reorganization on lp8788_adc_read_raw().

Patch v4.
Fix adc_raw function: support RAW and SCALE channel info.
Change LP8788 ADC platform data - iio map.
Enables the default IIO map.

Patch v3.
Fix wrong size of allocating iio private data.
Fix coding styles.

Patch v2.
Support RAW and SCALE interface for IIO consumer.
Clean up the iio channel spec macro.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio: Move ad7476 driver out of staging

The ad7476 driver is a driver for simple single channel ADCs. The driver does
not export any experimental or custom ABI files nor do the static code check
tools report any issues, so move the driver out of staging.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

staging:iio:adc: Add AD7791 driver

This patch adds support for the Analog Devices AD7787, AD7788, AD7789, AD7790
and AD7791 Sigma Delta Analog-to-Digital converters.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adc: Add common code for ADI Sigma Delta devices

Most devices from the Analog Devices Sigma Delta family use a similar scheme for
communication with the device. This includes register access, as well as trigger
handling. But each device sub-family has different features and different
register layouts (some even have no registers at all) and thus it is impractical
to try to support all of the devices by the same driver. This patch adds a
common base library for Sigma Delta converter devices. It will be used by
individual drivers.

This code is mostly based on the three existing Sigma Delta drivers the AD7192,
AD7780 and AD7793, but has been improved for more robustness and flexibility.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

iio:adc: Add AD7265/AD7266 support

This patch adds support for the Analog Devices AD7265 and AD7266
Analog-to-Digital converters.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

ARM: AT91: IIO: Add AT91 ADC driver.

Add the ADC driver for Atmel's AT91SAM9G20-EK, AT91SAM9M10G45-EK
and AT91SAM9X5 family boards.

It has support for both software and hardware triggers.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>