i3c: ast2600: Add AST2600 platform-specific driver

Now that we have platform-specific infrastructure for the dw i3c driver,
add platform support for the ASPEED AST2600 SoC.

The AST2600 has a small set of "i3c global" registers, providing
platform-level i3c configuration outside of the i3c core.

For the ast2600, we need a couple of extra setup operations:

- on probe: find the i3c global register set and parse the SDA pullup
resistor values

- on init: set the pullups accordingly, and set the i3c instance IDs

Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230331091501.3800299-4-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

i3c: master: svc: Add Silvaco I3C master driver

Add support for Silvaco I3C dual-role IP. The master role is supported
in SDR mode only. I2C transfers have not been tested but are shared
because they are very close to the I3C transfers in terms of register
configuration.

The IBI processing follows this logic:
- When a slave advertizes an interrupt (SDA pulled low) an interrupt
gets generated by the master. This time is unbounded and may be
deferred.
- The IRQ handler itself does not process anything: it only queues a
work that will be run in non-atomic context. This is needed because
short wait periods must be experienced.
- The IBI job is divided in two parts: the first one is "critical" in
the sense that it may not support getting interrupted. If this
happens, after this first section the driver checks the master error
register and depending on its content either flushes everything and
errors out, or ends the processing (this second section may be
interrupted).
- If the critical section got interrupted, the slave will
automatically respin it's IBI request when it will be allowed to.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210121101808.14654-6-miquel.raynal@bootlin.com

i3c/master/mipi-i3c-hci: Specify HAS_IOMEM dependency

The MIPI i3c HCI driver makes use of IOMEM functions like
devm_platform_ioremap_resource(), which are only available if
CONFIG_HAS_IOMEM is defined.

This causes the driver to be enabled under make ARCH=um allyesconfig,
even though it won't build.

By adding a dependency on HAS_IOMEM, the driver will not be enabled on
architectures which don't support it.

Fixes: 9ad9a52cce28 ("i3c/master: introduce the mipi-i3c-hci driver")
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210127040636.1535722-1-davidgow@google.com

i3c/master: introduce the mipi-i3c-hci driver

This adds basic support for hardware implementing the MIPI I3C HCI
specification. This driver is currently limited by the capabilities
of the I3C subsystem, meaning things like scheduled commands,
auto-commands and NCM mode are not yet supported.

This supports version 1.0 of the MIPI I3C HCI spec, as well as the
imminent release of version 1.1. Support for draft version 2.0 of the
spec is also largely included with the caveat that future adjustments
to this code are likely as the spec is still a work in progress.

This is also lightly tested as actual hardware is still very scarce,
even for HCI v1.0. Hence the EXPERIMENTAL tag. Further contributions
to this driver are expected once vendor implementations and new I3C
devices become available.

Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/20201111220510.3622216-3-nico@fluxnic.net

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i3c: master: Add driver for Synopsys DesignWare IP

Add driver for Synopsys DesignWare I3C master IP

Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

i3c: master: Add driver for Cadence IP

Add a driver for Cadence I3C master IP.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i3c: Add core I3C infrastructure

Add core infrastructure to support I3C in Linux and document it.

This infrastructure adds basic I3C support. Advanced features will be
added afterwards.

There are a few design choices that are worth mentioning because they
impact the way I3C device drivers can interact with their devices:

- all functions used to send I3C/I2C frames must be called in
non-atomic context. Mainly done this way to ease implementation, but
this is not set in stone, and if anyone needs async support, new
functions can be added later on.
- the bus element is a separate object, but it's tightly coupled with
the master object. We thus have a 1:1 relationship between i3c_bus
and i3c_master_controller objects, and if 2 master controllers are
connected to the same bus and both exposed to the same Linux instance
they will appear as two distinct busses, and devices on this bus will
be exposed twice.
- I2C backward compatibility has been designed to be transparent to I2C
drivers and the I2C subsystem. The I3C master just registers an I2C
adapter which creates a new I2C bus. I'd say that, from a
representation PoV it's not ideal because what should appear as a
single I3C bus exposing I3C and I2C devices here appears as 2
different buses connected to each other through the parenting (the
I3C master is the parent of the I2C and I3C busses).
On the other hand, I don't see a better solution if we want something
that is not invasive.

Missing features:
- I3C HDR modes are not supported
- no support for multi-master and the associated concepts (mastership
handover, support for secondary masters, ...)
- I2C devices can only be described using DT because this is the only
use case I have. However, the framework can easily be extended with
ACPI and board info support
- I3C slave framework. This has been completely omitted, but shouldn't
have a huge impact on the I3C framework because I3C slaves don't see
the whole bus, it's only about handling master requests and generating
IBIs. Some of the struct, constant and enum definitions could be
shared, but most of the I3C slave framework logic will be different

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>