| #
8be143b9 |
|
23-Feb-2024 |
Guenter Roeck <linux@roeck-us.net> |
hwmon: (pmbus/tda38640) Use PMBUS_REGULATOR_ONE to declare regulator
If a chip only provides a single regulator, it should be named 'vout'
and not 'vout0'. Declare regulator using PMBUS_REGULATOR_ONE() to make
that happen.
Cc: Conor Dooley <conor@kernel.org>
Cc: Naresh Solanki <naresh.solanki@9elements.com>
Cc: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240223-catnap-companion-c42fdd8ad110@spud
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
| #
923774d7 |
|
31-Aug-2023 |
Patrick Rudolph <patrick.rudolph@9elements.com> |
hwmon: (pmbus/tda38640) Add workaround for SVID mode
TDA38640 can operate in either PMBus mode or SVID mode.
In SVID mode, by design ENABLE pin is the only option for controlling
the output rail i.e., ENABLE pin is chained to power good of another
reglator & FPGA.
In cases where the chip is configured for SVID mode, and the ENABLE pin
is set at a fixed level or is left unconnected (with an internal
pull-down), while requiring software control, the following
workaround is necessary.
The workaround utilizes ENABLE pin polarity flipping to control
output rail.
If property 'infineon,en-pin-fixed-level' is specified then
determine if chip is in SVID mode by checking BIT15 of MTP memory offset
0x44 as described in the datasheet.
If chip is in SVID mode then apply the workaround by
1. Determine EN pin level
2. Maps BIT7 of OPERATION(01h) to EN_PIN_POLARITY(BIT1) of
PB_ON_OFF_CONFIG.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230831190731.265099-3-Naresh.Solanki@9elements.com
[groeck: Dropped unnecessary line continuation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
| #
1975d167 |
|
05-May-2023 |
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> |
hwmon: Switch i2c drivers back to use .probe()
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230505131718.1210071-1-u.kleine-koenig@pengutronix.de
[groeck: Added missing change in pmbus/acbel-fsg032.c]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|