drm/msm/dpu: fix the programming of INTF_CFG2_DATA_HCTL_EN

Currently INTF_CFG2_DATA_HCTL_EN is coupled with the enablement
of widebus but this is incorrect because we should be enabling
this bit independent of widebus except for cases where compression
is enabled in one pixel per clock mode.

Fix this by making the condition checks more explicit and enabling
INTF_CFG2_DATA_HCTL_EN for all other cases when supported by DPU.

Fixes: 3309a7563971 ("drm/msm/dpu: revise timing engine programming to support widebus feature")
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/576722/
Link: https://lore.kernel.org/r/20240201004737.2478-1-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Drop enable and frame_count parameters from dpu_hw_setup_misr()

Drop the enable and frame_count parameters from dpu_hw_setup_misr() as they
are always set to the same values.

In addition, replace MISR_FRAME_COUNT_MASK with MISR_FRAME_COUNT as
frame_count is always set to the same value.

Fixes: 7b37523fb1d1 ("drm/msm/dpu: Move MISR methods to dpu_hw_util")
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/572009/
Link: https://lore.kernel.org/r/20231213-encoder-fixup-v4-2-6da6cd1bf118@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Set input_sel bit for INTF

Set the input_sel bit for encoders as it was missed in the initial
implementation.

Reported-by: Rob Clark <robdclark@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/39
Fixes: 91143873a05d ("drm/msm/dpu: Add MISR register support for interface")
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/572007/
Link: https://lore.kernel.org/r/20231213-encoder-fixup-v4-1-6da6cd1bf118@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: use devres-managed allocation for HW blocks

Use devm_kzalloc to create HW block structure. This allows us to remove
corresponding kfree and drop all dpu_hw_*_destroy() functions as well as
dpu_rm_destroy(), which becomes empty afterwards.

Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/570041/
Link: https://lore.kernel.org/r/20231201211845.1026967-7-dmitry.baryshkov@linaro.org

drm/msm/dpu: enable INTF TE operations only when supported by HW

The DPU_INTF_TE bit is set for all INTF blocks on DPU >= 5.0, however
only INTF_1 and INTF_2 actually support tearing control (both are
INTF_DSI). Rather than trying to limit the DPU_INTF_TE feature bit to
those two INTF instances, check for the major && INTF type.

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/555547/
Link: https://lore.kernel.org/r/20230904020454.2945667-6-dmitry.baryshkov@linaro.org

drm/msm/dpu: inline _setup_intf_ops()

Inline the _setup_intf_ops() function, it makes it easier to handle
different conditions involving INTF configuration.

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/555551/
Link: https://lore.kernel.org/r/20230904020454.2945667-5-dmitry.baryshkov@linaro.org

drm/msm/dpu: Enable widebus for DSI INTF

DPU supports a data-bus widen mode for DSI INTF.

Enable this mode for all supported chipsets if widebus is enabled for DSI.

Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/553756/
Link: https://lore.kernel.org/r/20230822-add-widebus-support-v4-2-9dc86083d6ea@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: rename enable_compression() to program_intf_cmd_cfg()

Rename the intf's enable_compression() op to program_intf_cmd_cfg()
and allow it to accept a struct intf_cmd_mode_cfg to program
all the bits at once. This can be re-used by widebus later on as
well as it touches the same register.

changes in v5:
- rename struct intf_cmd_mode_cfg to dpu_hw_intf_cmd_mode_cfg
- remove couple of comments

Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/546806/
Link: https://lore.kernel.org/r/20230712012003.2212-5-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: rename all hw_intf structs to have dpu_hw prefix

dpu_hw_intf has a few instances of structs which do not have
the dpu_hw prefix. Lets fix this by renaming those structs
and updating the usage of those accordingly.

Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/546805/
Link: https://lore.kernel.org/r/20230712012003.2212-4-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: use dpu core's major version to enable data compress

Instead of using a feature bit to decide whether to enable data
compress or not for DSC use-cases, use dpu core's major version
instead by assigning the enable_compression op based on the
dpu core's major version.

To make this possible pass the struct dpu_mdss_version to
dpu_hw_intf_init().

This will avoid defining feature bits for every bit level details of
registers.

changes in v5:
- none

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/546803/
Link: https://lore.kernel.org/r/20230712012003.2212-3-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Set DATA_COMPRESS on command mode for DCE/DSC 1.2

Add a DPU INTF op to set the DCE_DATA_COMPRESS bit to enable the
DCE/DSC 1.2 datapath

Note: For now, this op is called for command mode encoders only. Changes to
set DATA_COMPRESS for video mode encoders will be posted along with DSC
v1.2 support for DP.

Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/541966/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-4-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: use PINGPONG_NONE to unbind INTF from PP

Currently the driver passes the PINGPONG index to
dpu_hw_intf_ops::bind_pingpong_blk() callback and uses separate boolean
flag to tell whether INTF should be bound or unbound. Simplify this by
passing PINGPONG_NONE in case of unbinding and drop the flag completely.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/540968/
Link: https://lore.kernel.org/r/20230604031308.894274-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Implement tearcheck support on INTF block

Since DPU 5.0.0 the TEARCHECK registers and interrupts moved out of the
PINGPONG block and into the INTF. Implement the necessary callbacks in
the INTF block, and use these callbacks together with the INTF_TEAR
interrupts.

Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/534234/
Link: https://lore.kernel.org/r/20230411-dpu-intf-te-v4-21-27ce1a5ab5c6@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Sort INTF registers numerically

A bunch of registers were appended at the end in e.g. commit
91143873a05d ("drm/msm/dpu: Add MISR register support for interface")
rather than being inserted in a place that maintains numerical sorting:
restore said numerical sorting.

Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/534213/
Link: https://lore.kernel.org/r/20230411-dpu-intf-te-v4-10-27ce1a5ab5c6@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Remove extraneous register define indentation

A bunch of registers are indented with two extra spaces, looking as if
these are values corresponding to the previous register which is not the
case, rather these are simply also register offsets and should only have
a single space separating them and the #define keyword.

Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/534218/
Link: https://lore.kernel.org/r/20230411-dpu-intf-te-v4-9-27ce1a5ab5c6@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Pass catalog pointers in RM to replace for-loop ID lookups

The Resource Manager already iterates over all available blocks from the
catalog, only to pass their ID to a dpu_hw_xxx_init() function which
uses an _xxx_offset() helper to search for and find the exact same
catalog pointer again to initialize the block with, fallible error
handling and all.

Instead, pass const pointers to the catalog entries directly to these
_init functions and drop the for loops entirely, saving on both
readability complexity and unnecessary cycles at boot.

Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/533861/
Link: https://lore.kernel.org/r/20230418-dpu-drop-useless-for-lookup-v3-3-e8d869eea455@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Drop unused members from HW structs

Some of these members were initialized while never read, while others
were not even assigned any pointer value at all. Drop them to save some
space, and above all confusion when looking at or accidentally
dereferencing these members.

Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/533862/
Link: https://lore.kernel.org/r/20230418-dpu-drop-useless-for-lookup-v3-2-e8d869eea455@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: use hsync/vsync polarity set by the encoder

Do not override the hsync/vsync polarity passed by the encoder when
setting up intf timings. The same logic was used in both the encoder and
intf code to set the DP and DSI polarities, so those interfaces are not
impacted. However for HDMI, the polarities were overriden to static
values based on the vertical resolution, instead of using the actual
mode polarities.

Signed-off-by: Arnaud Vrac <avrac@freebox.fr>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/532901/
Link: https://lore.kernel.org/r/20230419-dpu-tweaks-v1-3-d1bac46db075@freebox.fr
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Remove duplicate register defines from INTF

The INTF_FRAME_LINE_COUNT_EN, INTF_FRAME_COUNT and INTF_LINE_COUNT
registers are already defined higher up, in the right place when sorted
numerically.

Fixes: 25fdd5933e4c ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/534231/
Link: https://lore.kernel.org/r/20230411-dpu-intf-te-v4-8-27ce1a5ab5c6@somainline.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

drm/msm/disp/dpu: get timing engine status from intf status register

Recommended way of reading the interface timing gen status is via
status register. Timing gen status register will give a reliable status
of the interface especially during ON/OFF transitions. This support was
added from DPU version 5.0.0.

Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/524724/
Link: https://lore.kernel.org/r/1677774797-31063-6-git-send-email-quic_vpolimer@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: merge base_off with blk_off in struct dpu_hw_blk_reg_map

There is little point in keeping a separate MDP address and block offset
in this struct. Merge them to form a new blk_addr field used for all
register access.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/488017/
Link: https://lore.kernel.org/r/20220601161349.1517667-4-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/dpu: drop length from struct dpu_hw_blk_reg_map

We (nearly) do not use the length field from struct dpu_hw_blk_reg_map,
so we can drop it safely.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/488013/
Link: https://lore.kernel.org/r/20220601161349.1517667-3-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/dpu: Add MISR register support for interface

Add support for setting MISR registers within the interface

Changes since V1:
- Replaced dpu_hw_intf collect_misr and setup_misr implementations with
calls to dpu_hw_utils helper methods

Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/490730/
Link: https://lore.kernel.org/r/20220622171835.7558-4-quic_jesszhan@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: remove hwversion field from data structures

The driver should not depend on hw revision for detecting features.
Instead it should use features from the hw catalog. Drop the hwversion
field from struct dpu_mdss_cfg and struct dpu_hw_blk_reg_map.

Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/488160/
Link: https://lore.kernel.org/r/20220602202447.1755115-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: drop INTF_EDP from interface type conditions

To remove possible confusion between (old) INTF_EDP and newer INTF_DP,
stop using INTF_EDP in DPU's code. Until the 8x74/8x84 SoCs are
supported by DPU driver, there is no point in using INTF_EDP.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/475560/
Link: https://lore.kernel.org/r/20220222062246.242577-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: revise timing engine programming to support widebus feature

Widebus feature will transmit two pixel data per pixel clock to interface.
Timing engine provides driving force for this purpose. This patch base
on HPG (Hardware Programming Guide) to revise timing engine register
setting to accommodate both widebus and non widebus application. Also
horizontal width parameters need to be reduced by half since two pixel
data are clocked out per pixel clock when widebus feature enabled.

Widebus can be enabled individually at DP. However at DSI, widebus have
to be enabled along with DSC to achieve pixel clock rate be scaled down
with same ratio as compression ratio when 10 bits per source component.
Therefore this patch add no supports of DSI related widebus and compression.

Changes in v2:
-- remove compression related code from timing
-- remove op_info from struct msm_drm_private
-- remove unnecessary wide_bus_en variables
-- pass wide_bus_en into timing configuration by struct msm_dp

Changes in v3:
-- split patch into 3 patches

Changes in v4:
-- rework timing engine to not interfere with dsi/hdmi
-- cover both widebus and compression

Changes in v5:
-- remove supports of DSI widebus and compression

Changes in v7:
-- split this patch into 3 patches
-- add Tested-by

Changes in v8:
-- move new registers writes under DATA_HCTL_EN features check.

Changes in v10:
-- add const inside dpu_encoder_is_widebus_enabled()
-- drop useless parenthesis please

Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/476281/
Link: https://lore.kernel.org/r/1645824192-29670-4-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: replace BIT(x) with correspond marco define string

To improve code readability, this patch replace BIT(x) with
correspond register bit define string

Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/476280/
Link: https://lore.kernel.org/r/1645824192-29670-3-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: adjust display_v_end for eDP and DP

The “DP timing” requires the active region to be defined in the
bottom-right corner of the frame dimensions which is different
with DSI. Therefore both display_h_end and display_v_end need
to be adjusted accordingly. However current implementation has
only display_h_end adjusted.

Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>

Fixes: fc3a69ec68d3 ("drm/msm/dpu: intf timing path for displayport")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/476277/
Link: https://lore.kernel.org/r/1645824192-29670-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: hw_blk: make dpu_hw_blk empty opaque structure

The code does not really use dpu_hw_blk fields, so drop them, making
dpu_hw_blk empty structure.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210515190909.1809050-5-dmitry.baryshkov@linaro.org
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/dpu: drop dpu_hw_blk_destroy function

The dpu_hw_blk_destroy() function is empty, so we can drop it now.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210515190909.1809050-3-dmitry.baryshkov@linaro.org
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/dpu: remove unused dpu_hw_blk features

Remove all unused dpu_hw_blk features and functions:
- dpu_hw_blk_get()/_put() and respective refcounting,
- global list of all dpu_hw_blk instances,
- dpu_hw_blk_ops and empty implementation inside each hw_blk subdriver.

This leaves dpu_hw_blk as a placeholder with just type and index.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210515190909.1809050-2-dmitry.baryshkov@linaro.org
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/disp/dpu1: enable DATA_HCTL_EN for sc7280 target

The reset value of INTF_CONFIG2 register is changed
for SC7280 family. Changes are added to program
this register correctly based on the target.

DATA_HCTL_EN in INTF_CONFIG2 register allows data
to be transferred at a different rate than video
timing. When this is set, the number of data per
line follows DISPLAY_DATA_HCTL register value.
This change adds support to program these
registers for sc7280 target.

Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Link: https://lore.kernel.org/r/1617685792-14376-5-git-send-email-mkrishn@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/disp/dpu1: turn off vblank irqs aggressively in dpu driver

Set the flag vblank_disable_immediate = true to turn off vblank irqs
immediately as soon as drm_vblank_put is requested so that there are
no irqs triggered during idle state. This will reduce cpu wakeups
and help in power saving.

To enable vblank_disable_immediate flag the underlying KMS driver
needs to support high precision vblank timestamping and also a
reliable way of providing vblank counter which is incrementing
at the leading edge of vblank.

This patch also brings in changes to support vblank_disable_immediate
requirement in dpu driver.

Changes in v1:
- Specify reason to add vblank timestamp support. (Rob).
- Add changes to provide vblank counter from dpu driver.

Changes in v2:
- Fix warn stack reported by Rob Clark with v2 patch.

Changes in v3:
- Move back to HW frame counter (Rob).

Changes in v4:
- Frame count mismatch was causing a DRM WARN stack spew.
DPU HW will increment the frame count at the end of
the sync, where as vblank will be triggered at the
fetch_start counter which is calculated as v_total - vfp.
This is to start fetching early for panels with low
vbp w.r.t hw latency lines.

Add logic to detect the line count if it falls between
vactive and v_total then return incremented frame count value.

Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Link: https://lore.kernel.org/r/1613651746-12783-1-git-send-email-kalyan_t@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/dpu: intf timing path for displayport

Calculate the correct timings for displayport, from downstream driver.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/dpu: don't use INTF_INPUT_CTRL feature on sdm845

The INTF_INPUT_CTRL feature is not available on sdm845, so don't set it.

This also adds separate feature bits for INTF (based on downstream) instead
of using CTL feature bit for it, and removes the unnecessary NULL check in
the added bind_pingpong_blk function.

Fixes: 73bfb790ac786ca55fa2786a06f59 ("msm:disp:dpu1: setup display datapath for SC7180 target")

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>

msm:disp:dpu1: setup display datapath for SC7180 target

Add changes to setup display datapath on SC7180 target.

Changes in v1:
- Add changes to support ctl_active on SC7180 target.
- While selecting the number of mixers in the topology
consider the interface width.

Changes in v2:
- Spawn topology mixer selection into separate patch (Rob Clark).
- Add co-developed-by tags in the commit msg (Stephen Boyd).

Changes in v3:
- Fix kernel checkpatch errors in v2.

This patch has dependency on the below series

https://patchwork.kernel.org/patch/11253747/

Co-developed-by: Shubhashree Dhar <dhar@codeaurora.org>
Signed-off-by: Shubhashree Dhar <dhar@codeaurora.org>
Co-developed-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/dpu: Mark various data tables as const

These structures look like a bunch of data tables that aren't going to
change after boot. Let's move them to the const RO section of memory so
that they can't be modified at runtime on modern machines.

Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 284

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 294 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/msm/dpu: Cleanup callers of dpu_hw_blk_init

Outside of superfluous parameter checks the dpu_hw_blk_init()
doesn't have any failure paths. Switch it over to be a void
function and we can remove error handling paths in all the functions
that call it. While we're in those functions remove unneeded
initialization for a static variable.

v3: No changes
v2: Removed a cleanup intended for a different patch

Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

drm/msm/dpu: Remove dpu_dbg

The functions in dpu_dbg.c aren't used. The two main dump functions
fail after a lookup from dpu_dbg_base.reg_base_list which turns out
to never be populated and once those are removed the rest of the
file doesn't make any sense.

v3: No changes
v2: Moved some unrelated changes to another patch

Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

drm/msm/dpu: remove debugfs support for misr

MISR support is the debug feature present in Snapdragon chipsets.
At the layer mixer and interfaces, MISR algorithm can generate CRC
signatures of the pixel data which can be used for validating
the frames generated. Since there are no clients for this feature,
strip down the support from the driver.

changes in v4:
- changed introduced in the series
changes in v5:
- update commit text with the need for the change(Sean)

Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

drm/msm: Add SDM845 DPU support

SDM845 SoC includes the Mobile Display Sub System (MDSS) which is a
top level wrapper consisting of Display Processing Unit (DPU) and
display peripheral modules such as Display Serial Interface (DSI)
and DisplayPort (DP).

MDSS functions essentially as a back-end composition engine. It blends
video and graphic images stored in the frame buffers and scans out the
composed image to a display sink (over DSI/DP).

The following diagram represents hardware blocks for a simple pipeline
(two planes are present on a given crtc which is connected to a DSI
connector):

MDSS
+---------------------------------+
| +-----------------------------+ |
| | DPU | |
| | +--------+ +--------+ | |
| | | SSPP | | SSPP | | |
| | +----+---+ +----+---+ | |
| | | | | |
| | +----v-----------v---+ | |
| | | Layer Mixer (LM) | | |
| | +--------------------+ | |
| | +--------------------+ | |
| | | PingPong (PP) | | |
| | +--------------------+ | |
| | +--------------------+ | |
| | | INTERFACE (VIDEO) | | |
| | +---+----------------+ | |
| +------|----------------------+ |
| | |
| +------|---------------------+ |
| | | DISPLAY PERIPHERALS | |
| | +---v-+ +-----+ | |
| | | DSI | | DP | | |
| | +-----+ +-----+ | |
| +----------------------------+ |
+---------------------------------+

The number of DPU sub-blocks (i.e. SSPPs, LMs, PP blocks and INTFs)
depends on SoC capabilities.

Overview of DPU sub-blocks:
---------------------------
* Source Surface Processor (SSPP):
Refers to any of hardware pipes like ViG, DMA etc. Only ViG pipes are
capable of performing format conversion, scaling and quality improvement
for source surfaces.

* Layer Mixer (LM):
Blend source surfaces together (in requested zorder)

* PingPong (PP):
This block controls frame done interrupt output, EOL and EOF generation,
overflow/underflow control.

* Display interface (INTF):
Timing generator and interface connecting the display peripherals.

DRM components mapping to DPU architecture:
------------------------------------------
PLANEs maps to SSPPs
CRTC maps to LMs
Encoder maps to PPs, INTFs

Data flow setup:
---------------
MDSS hardware can support various data flows (e.g.):
- Dual pipe: Output from two LMs combined to single display.
- Split display: Output from two LMs connected to two separate
interfaces.

The hardware capabilities determine the number of concurrent data paths
possible. Any control path (i.e. pipeline w/i DPU) can be routed to any
of the hardware data paths. A given control path can be triggered,
flushed and controlled independently.

Changes in v3:
- Move msm_media_info.h from uapi to dpu/ subdir
- Remove preclose callback dpu (it's handled in core)
- Fix kbuild warnings with parent_ops
- Remove unused functions from dpu_core_irq
- Rename mdss_phys to mdss
- Rename mdp_phys address space to mdp
- Drop _phys from vbif and regdma binding names

Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rajesh Yadav <ryadav@codeaurora.org>
Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[robclark minor rebase]
Signed-off-by: Rob Clark <robdclark@gmail.com>